Revision 0:cc2f9ea8cd1f, committed 2019-06-16

Comitter:

foxbrianr

Date:

Sun Jun 16 00:36:06 2019 +0000

Commit message:

demo microcom

Changed in this revision

--- /dev/null	Thu Jan 01 00:00:00 1970 +0000
+++ b/MicroCom.h	Sun Jun 16 00:36:06 2019 +0000
@@ -0,0 +1,127 @@
+/*
+1st Byte:  Header byte:  always 0x40.
+
+2nd Byte:  Is a bit field:    free_a7            :1,    bit 7
+            Reserved (fire service)    :1,    bit 6
+            Reserved         :1,    bit 5
+            Reserved        :1,    bit 4
+            Reserved        :1,    bit 3
+            play strobe         :1,    bit 2
+            arrival_dn_arrow     :1,    bit 1
+            arrival_up_arrow     :1,    bit0
+
+3rd Byte:  Scan_slot. zero is reserved, 1 through 254, (119 may be max value in some cases)
+
+4th Byte: Message_number.  zero is no message, 1 through 126, (63 may be max value in some cases)
+
+5th Byte:  Is a bit field:    Rear arrival dn arr    :1,    bit 7
+            Rear arrival up arr    :1,    bit 6
+            Message level hi bit    :1,    bit 5
+            Message level low bit    :1,    bit 4
+            Passing chime         :1,    bit 3
+            Reserved        :1,    bit 2
+            traveling dn arrow    :1,    bit 1
+            traveling up arrow    :1,    bit 0
+
+6th Byte:  ASCII floor char, msb.
+
+7th Btye:  ASCII floor char, mid.
+
+8thByte:  ASCII floor char, lsb.
+            Note:  floor ASCII range is 0x30 through 0x5a (‘0’ – ‘Z’). 
+                0x3a  through 0x40 are special characters with 
+                0x3b being the space or blank character(semicolon)
+                0x3d is normally displayed as a minus character.
+9th Byte:  ASCII Mess. char, msb.
+
+10th Byte:  ASCII Mess. Char, mid.
+
+11th Byte:  ASCII Mess. char, lsb.
+            Note:  message ASCII range is 0x30 through 0x5b (‘0’ – ‘[’). 
+                0x3a  through 0x40 are special characters with 
+                0x3b being the space or blank character(semicolon)
+                0x5d is sent when there is no message (instead of spaces).
+                So bytes 9, 10, and 11 will each be ‘[‘  when no message. 
+12th Byte: checksum, two’s complement of bytes 1 through 11.
+
+Example:
+ 0x40,    header
+ 0x01,    up arrow for lantern
+ 0x01,     floor number 1,
+ 0x03,    message number 3 activated 
+ 0x11,    message level 1, direction arrow is up
+ 0x4c,    ascii floor character ‘L’
+ 0x42,    ascii floor character ‘B,
+ 0x59,    ascii floor character ‘Y’
+ 0x3b,    ascii message character ‘;’ for space or blank
+ 0x4e,    ascii message character ‘N’
+ 0x44,    ascii message character ‘D’
+ 0xf6,    checksum (two’s complement). 
+ */
+ 
+class MicroComMessage
+{
+    public:
+        uint8_t message[12];
+        
+        uint8_t * getMessage(){ return message;};
+        
+        
+        
+        void SetFloor(char* floor) {};
+        
+        void SetMessage( char* msg){};
+        
+        
+        
+};
+
+/*
+Floor and Arrow Information (0x501)
+The floor and arrow information contains the current car position and hall arrows.
+Packet Data
+Byte 1
+Front arrows
+Bit 0 – Front arrival arrow up
+Bit 1 – Front arrival arrow down
+Bit 2 – Play Strobe
+Bit 3-5 – Reserved
+Bit 6 – Fire Warning Lamp
+Byte 2
+Floor Number.  A floor number of 0 is not a valid.
+Byte 3
+Priority message number
+Byte 4
+Travel and rear arrows
+Bit 0 – Travel arrow up
+Bit 1 – Travel arrow down
+Bit 2 – unused
+Bit 3 – Passing Chime
+Bit 4 – Message Level Low Bit
+Bit 5 – Message Level High Bit
+Bit 6 – Rear arrival arrow up
+Bit 7 – Rear arrival arrow down
+Byte 5-8
+Reserved
+*/
+
+void GetMessage501(char * floor, char * msg, char lantern )
+{
+}
+/*
+Floor and Message characters (0x502)
+The floor and message characters packet contains the marking used to represent the floor or priority message on displays.
+Packet Data
+    Byte 1    Floor marking character (leftmost)
+    Byte 2    Floor marking character
+    Byte 3    Floor marking character (rightmost)
+    Byte 4    Message marking character (leftmost)
+    Byte 5    Message marking character
+    Byte 6    Message marking character (rightmost)
+    Byte 7    Lantern Position (ThyssenKrupp)
+    Byte 8    Unused
+
+*/
+void GetMessage502(char * floor, char * msg, char lantern )
+{
+}
\ No newline at end of file

--- /dev/null	Thu Jan 01 00:00:00 1970 +0000
+++ b/emic2.h	Sun Jun 16 00:36:06 2019 +0000
@@ -0,0 +1,41 @@
+#define speakf printf
+class emic2 : public Stream
+{
+public :
+    emic2(PinName tx, PinName rx): _cmd(tx,rx) {
+        _cmd.baud(9600);
+        _cmd.putc('X'); //stop talking if reset and not a power on
+        _cmd.putc('\r'); // Send a CR in case the system is already up
+        wait(1); //delay for emic power on boot or reset respone
+        while (_cmd.getc() != ':');   // When the Emic 2 has initialized and is ready, it will send a single ':'
+        while (_cmd.readable()) _cmd.getc();//flush out buffer just in case
+    };
+    void ready() {
+        while (_cmd.getc() != ':');
+        while (_cmd.readable()) _cmd.getc();//flush out recieve buffer just in case
+    };
+    int readable() {
+        return _cmd.readable();
+    };
+    int getc() {
+        return _cmd.getc();
+    }
+    void volume(int x) {
+        speakf("V%D\r",x);
+        ready();
+    }
+    void voice(int x) {
+        speakf("N%D\r",x);
+        ready();
+    }
+protected :
+    Serial     _cmd;
+    //used by printf - supply it and printf works!
+    virtual int _putc(int c) {
+        _cmd.putc(c);
+        return 0;
+    };
+    virtual int _getc() {
+        return -1;
+    };
+};

--- /dev/null	Thu Jan 01 00:00:00 1970 +0000
+++ b/main.cpp	Sun Jun 16 00:36:06 2019 +0000
@@ -0,0 +1,135 @@
+#include "mbed.h"
+  
+DigitalOut myled1(LED1);
+DigitalOut myled2(LED2);
+DigitalOut myled3(LED3);
+DigitalOut myled4(LED3);
+
+DigitalOut myled(LED1);
+#include "emic2.h"
+
+emic2 myVoice2Text(p28, p27); //serial RX,TX pins to emic
+
+Serial pc(USBTX, USBRX, 9600); //tx,rx,baud
+
+Serial rs485port1(p9, p10, 9600); //tx,rx,baud
+DigitalOut rs485port1mode (p11); //Transmit = 1, Receive = 0
+
+Serial rs485port2(p13, p14, 9600); //tx,rx,baud
+DigitalOut rs485port2mode (p12); //Transmit = 1, Receive = 0
+
+int dataRxCnt        = 0;
+int dataRxBuffer[4]  = {0};
+int cur_address        = 0;
+    
+char fault[4];
+    
+void rx485Message() {
+    // Note: you need to actually read from the serial to clear the RX interrupt
+    int value = rs485port1.getc();
+    
+    if (value){
+        dataRxBuffer[dataRxCnt++]=value;
+        
+        if(dataRxCnt==4) {
+            cur_address = 10*(dataRxBuffer[0] -0x30) + (dataRxBuffer[1] -0x30);
+            pc.printf("Received >> %02d \n\r", cur_address);
+            memset(dataRxBuffer,0,sizeof(dataRxBuffer));
+            dataRxCnt=0;
+        }
+    }
+    myled4 = !myled4;
+}
+
+
+void tx485Message(int address) {
+    
+    int sum =0;
+    
+    char dataTxBuffer[12];
+    sum += dataTxBuffer[0] = 0x40;
+    sum += dataTxBuffer[1]  = 0x01;
+    sum += dataTxBuffer[2]  = address; // floor number
+    sum += dataTxBuffer[3]  = 0x0;
+    sum += dataTxBuffer[4]  = 0x0;
+    sum += dataTxBuffer[5]  = 0x0;
+    sum += dataTxBuffer[6]  = (0x30 + address / 10); 
+    sum += dataTxBuffer[7]  = (0x30 + address % 10); 
+    ; //
+    sum += dataTxBuffer[8]  = 0x0;
+    sum += dataTxBuffer[9]  = 0x0;
+    sum += dataTxBuffer[10] = 0x0;
+    sum += dataTxBuffer[11] = (char)(~sum +1);
+    
+    for(int i= 0;i<12;i++){
+        rs485port2.putc(dataTxBuffer[i]);
+    }
+    
+}
+void say (char *format, ...)
+{
+    char buffer[128];
+    va_list args;
+    va_start(args, format);
+    vsprintf(buffer,format,args);
+    
+    myVoice2Text.speakf("S");//Speak command starts with "S"
+    myVoice2Text.speakf(buffer);  
+    myVoice2Text.speakf("\r"); 
+    myVoice2Text.ready(); 
+    
+    
+    va_end(args);
+}
+
+
+int main() {
+    
+    pc.printf("\n\r");
+    pc.printf("------------------------\n\r");
+    pc.printf("Serial Test\n\r");
+    pc.printf("version = %s %s\n\r", __DATE__, __TIME__ );
+    pc.printf("------------------------\n\r");
+    rs485port1mode = 0; // Receive
+    rs485port2mode = 1; // Transmit
+    
+    
+    myVoice2Text.voice(2);   
+    say("hello");
+    
+    rs485port1.attach(&rx485Message);     
+    
+    while(1) {
+        
+        myled1 != myled1;
+        wait(0.2);
+        
+        myled2 = 0;
+        myled3 = 0;
+        
+        #if 0
+        if(rs485port1.readable() ) {
+            memset(data,0,sizeof(data));
+            rs485port1.scanf("%2s", data);
+            for (int i = 0 ; i < sizeof(data);i++){
+                pc.printf("%02x ", data[i]);
+            }
+            pc.printf("\n\r");
+            
+            myled2 = 1;
+        }
+        else {
+            pc.printf("No serial data on port 1.\r\n");
+            myled3 = 1;
+        }
+        #endif
+        
+        if (cur_address)
+        {
+            tx485Message(cur_address);
+            say("%d is open", cur_address);
+        }
+                
+       wait_ms(1000);
+    }
+}

--- /dev/null	Thu Jan 01 00:00:00 1970 +0000
+++ b/mbed.bld	Sun Jun 16 00:36:06 2019 +0000
@@ -0,0 +1,1 @@
+https://os.mbed.com/users/mbed_official/code/mbed/builds/65be27845400
\ No newline at end of file