Diff: pinsettings.hpp

Revision:

2:c54ddf743283

--- /dev/null	Thu Jan 01 00:00:00 1970 +0000
+++ b/pinsettings.hpp	Sun May 05 17:14:17 2019 +0000
@@ -0,0 +1,101 @@
+/*Connect as follows:
+
+Power supply MUST BE 3.3V and GND to the respective pins.
+
+  RFID pins          ->   Board pinName   L432KC       FRDM-KL25Z
+  ---------------------------------------------------------------------
+  
+  =======================  BUS   ======================================
+  RFID MISO = pin4   ->   SPI_MISO        PA_6=D12     PTD3
+  RFID MOSI = pin3   ->   SPI_MOSI        PA_7=D11     PTD2
+  RFID SCK  = pin2   ->   SPI_SCK         PA_5=D13     PTD1
+  ======================= RFID 1 ====================================== 
+  RFID SDA  = pin1   ->   SPI_CS          PB_6=D10     PTD0
+  RFID RST  = pin7   ->                   PA_9=D8      PTA13
+  RFID IRQ  = pin5   ->                   -------- OPEN --------
+  ======================= RFID 2 ======================================
+  RFID SDA  = pin1   ->   SPI_CS          PA_12=D2     PTD5     
+  RFID RST  = pin7   ->                   PB_1=D6      PTC9
+  RFID IRQ  = pin5   ->                   -------- OPEN --------
+  =====================================================================
+
+Connecting the "HOUSE"
+  Location      Circuit latch function    L432KC       FRDM-KL25Z
+  ---------------------------------------------------------------------
+  Front door    Set                       A1           A1
+  Front door    Reset                     A2           A2
+  Room 1 door   Set                       A3           A3
+  Room 1 door   Reset                     A4           A4
+  =====================================================================
+  
+  Mapping:
+  Front door = r0 = rfid0
+  Room 1 door = r1 = rfid1
+  
+*/
+
+#include "mbed.h"
+#include "MFRC522.h"
+
+#ifndef COMPILING_FOR_KL25Z
+    #define COMPILING_FOR_KL25Z 1 //Set this to 1 to compile with KL25Z pins
+#endif
+
+
+#ifndef PINSETTINGS_H
+#define PINSETTINGS_H
+
+    #if COMPILING_FOR_KL25Z
+      // FRDM KL25Z pins
+      
+      //USB communication
+      #define SERIAL_TX PTE0  //UART0 USB
+      #define SERIAL_RX PTE1  //UART0 USB
+      
+      //BUS
+      #define SPI_MISO  PTD3
+      #define SPI_MOSI  PTD2
+      #define SPI_SCK   PTD1
+      
+      //RFID 1
+      #define SPI_CS1   PTD0  //Chip select can be any digital pin
+      #define MF_RESET1 PTA13
+      
+      //RFID 2
+      #define SPI_CS2   PTD5
+      #define MF_RESET2 PTC9
+    
+      //House circuit connections
+      #define FRONTDOOR_SET A1
+      #define FRONTDOOR_RST A2
+      #define ROOM1DOOR_SET A3
+      #define ROOM1DOOR_RST A4
+    
+    #else
+      // STM32 L432KC pins
+      
+      //USB communication
+      #define SERIAL_TX USBTX  //UART0 USB
+      #define SERIAL_RX USBRX  //UART0 USB
+      
+      //BUS
+      #define SPI_MISO  D12
+      #define SPI_MOSI  D11
+      #define SPI_SCK   D13
+      
+      //RFID 1
+      #define SPI_CS1   D10
+      #define MF_RESET1  D8
+      
+      //RFID 2
+      #define SPI_CS2    D2
+      #define MF_RESET2  D6
+    
+      //House circuit connections
+      #define FRONTDOOR_SET A1
+      #define FRONTDOOR_RST A2
+      #define ROOM1DOOR_SET A3
+      #define ROOM1DOOR_RST A4
+    
+    #endif
+#endif
\ No newline at end of file