File content as of revision 2:1e4061cedf1d:

/**
 ******************************************************************************
 * @file    main.cpp
 * @author  IPC Rennes
 * @version V1.0.0
 * @date    April 25th, 2016
 * @brief   mbed simple application for the STMicroelectronics X-NUCLEO-IHM12A1
 *          Motor Control Expansion Board: control of 2 Brush DC motors.
 ******************************************************************************
 * @attention
 *
 * <h2><center>&copy; COPYRIGHT(c) 2016 STMicroelectronics</center></h2>
 *
 * Redistribution and use in source and binary forms, with or without modification,
 * are permitted provided that the following conditions are met:
 *   1. Redistributions of source code must retain the above copyright notice,
 *      this list of conditions and the following disclaimer.
 *   2. Redistributions in binary form must reproduce the above copyright notice,
 *      this list of conditions and the following disclaimer in the documentation
 *      and/or other materials provided with the distribution.
 *   3. Neither the name of STMicroelectronics nor the names of its contributors
 *      may be used to endorse or promote products derived from this software
 *      without specific prior written permission.
 *
 * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
 * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
 * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
 * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
 * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
 * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
 * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
 * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
 * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
 * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
 *
 ******************************************************************************
 */

/* Includes ------------------------------------------------------------------*/

/* mbed specific header files. */
#include "mbed.h"

/* Component specific header files. */
#include "stspin240_250_class.h"

/* Variables -----------------------------------------------------------------*/

/* Initialization parameters of the motor connected to the expansion board. */
 Stspin240_250_Init_t initDeviceParameters =
 {
  20000, /* Frequency of PWM of Input Bridge A in Hz up to 100000Hz             */
  20000, /* Frequency of PWM of Input Bridge B in Hz up to 100000Hz             */
  20000, /* Frequency of PWM used for Ref pin in Hz up to 100000Hz              */
  50,    /* Duty cycle of PWM used for Ref pin (from 0 to 100)                  */
  TRUE   /* Dual Bridge configuration  (FALSE for mono, TRUE for dual brush dc) */
 };

/* Motor Control Component. */
STSPIN240_250 *motor;

/* Functions -----------------------------------------------------------------*/

/**
 * @brief  This is an example of error handler.
 * @param[in] error Number of the error
 * @retval None
 * @note   If needed, implement it, and then attach it:
 *           + motor->AttachErrorHandler(&myErrorHandler);
 */
void myErrorHandler(uint16_t error)
{
  /* Printing to the console. */
  printf("Error %d detected\r\n\n", error);
  
  /* Infinite loop */
  while(1)
  {
  }    
}

/**
 * @brief  This is an example of user handler for the flag interrupt.
 * @param  None
 * @retval None
 * @note   If needed, implement it, and then attach and enable it:
 *           + motor->AttachFlagIRQ(&myFlagIRQHandler);
 *           + motor->EnableFlagIRQ();
 *         To disable it:
 *           + motor->DisbleFlagIRQ();
 */
void myFlagIRQHandler(void)
{
   /* Code to be customised */
  /************************/

  printf("    WARNING: \"FLAG\" interrupt triggered.\r\n");

  /* Get the state of bridge A */
  uint16_t bridgeState  = motor->GetBridgeStatus(0);
  
  if (bridgeState == 0) 
  {
    if (motor->GetDeviceState(0) != INACTIVE)
    {
      /* Bridges were disabled due to overcurrent or over temperature */
      /* When  motor was running */
        myErrorHandler(0XBAD0);
    }
  }
}

/* Main ----------------------------------------------------------------------*/

int main()
{
  uint8_t demoStep = 0;
  
  /* Printing to the console. */
  printf("STARTING MAIN PROGRAM\r\n");
    
//----- Initialization 
  
  /* Initializing Motor Control Component. */
  #if (defined TARGET_NUCLEO_F030R8)||(defined TARGET_NUCLEO_F334R8)
  motor = new STSPIN240_250(D2, D9, D6, D7, D5, D4, A2);
  #elif (defined TARGET_NUCLEO_L152RE)
  motor = new STSPIN240_250(D2, D9, D6, D7, D5, D4, A3);
  #else
  motor = new STSPIN240_250(D2, D9, D6, D7, D5, D4, A0);
  #endif
  if (motor->Init(&initDeviceParameters) != COMPONENT_OK) exit(EXIT_FAILURE);

  /* Set dual bridge enabled as two motors are used*/
  motor->SetDualFullBridgeConfig(1);

  /* Attaching and enabling an interrupt handler. */
  motor->AttachFlagIRQ(&myFlagIRQHandler);
  motor->EnableFlagIRQ();
    
  /* Attaching an error handler */
  motor->AttachErrorHandler(&myErrorHandler);

  /* Printing to the console. */
  printf("Motor Control Application Example for 2 brush DC motors\r\n");

  /* Set PWM Frequency of Ref to 15000 Hz */ 
  motor->SetRefPwmFreq(0, 15000); 

  /* Set PWM duty cycle of Ref to 60% */ 
  motor->SetRefPwmDc(0, 60); 
  
  /* Set PWM Frequency of bridge A inputs to 10000 Hz */ 
  motor->SetBridgeInputPwmFreq(0,10000); 
  
  /* Set PWM Frequency of bridge B inputs to 10000 Hz */ 
  motor->SetBridgeInputPwmFreq(1,10000); 
  
  /* Infinite Loop. */
  printf("--> Infinite Loop...\r\n");
  while (1)
  {
    switch (demoStep)
    {  
        case 0:
          printf("STEP 0: Motor(0) FWD Speed=100%% - Motor(1) Inactive\r\n");
          /* Set speed of motor 0 to 100 % */
          motor->SetSpeed(0,100); 
          /* start motor 0 to run forward*/
          /* if chip is in standby mode */
          /* it is automatically awakened */
          motor->Run(0, BDCMotor::FWD);
          break;
         case 1:
          printf("STEP 1: Motor(0) FWD Speed=75%% - Motor(1) BWD Speed=100%%\r\n");
          /* Set speed of motor 0 to 75 % */
          motor->SetSpeed(0,75); 
          /* Set speed of motor 1 to 100 % */
          motor->SetSpeed(1,100); 
          /* start motor 1 to run backward */
          motor->Run(1, BDCMotor::BWD);
          break;
        case 2:
          printf("STEP 2: Motor(0) FWD Speed=50%% - Motor(1) BWD Speed=75%%\r\n");
          /* Set speed of motor 0 to 50 % */
          motor->SetSpeed(0,50);   
         /* Set speed of motor 1 to 75% */
          motor->SetSpeed(1,75); 
          break;      
        case 3:
          printf("STEP 3: Motor(0) FWD Speed=25%% - Motor(1) BWD Speed=50%%\r\n");
          /* Set speed of motor 0 to 25 % */
          motor->SetSpeed(0,25);  
          /* Set speed of motor 1 to 50% */
          motor->SetSpeed(1,50);          
          break;  
        case 4:
          printf("STEP 4: Motor(0) Stopped - Motor(1) BWD Speed=25%%\r\n");
          /* Stop Motor 0 */
          motor->HardStop(0);   
          /* Set speed of motor 1 to 25% */
          motor->SetSpeed(1,25);      
          break;         
         case 5:
          printf("STEP 5: Motor(0) BWD Speed=25%% - Motor(1) Stopped\r\n");
          /* Set speed of motor 0 to 25 % */
          motor->SetSpeed(0,25); 
          /* start motor 0 to run backward */
          motor->Run(0, BDCMotor::BWD);
          /* Stop Motor 1 */
          motor->HardStop(1);   
          break;
         case 6:
          printf("STEP 6: Motor(0) BWD Speed=50%% - Motor(1) FWD Speed=25%%\r\n");
          /* Set speed of motor 0 to 50 % */
          motor->SetSpeed(0,50); 
          /* Set speed of motor 1 to 25 % */
          motor->SetSpeed(1,25); 
          /* start motor 1 to run backward */
          motor->Run(1, BDCMotor::FWD);
          break;
        case 7:
          printf("STEP 7: Motor(0) BWD Speed=75%% - Motor(1) FWD Speed=50%%\r\n");
          /* Set speed of motor 0 to 75 % */
          motor->SetSpeed(0,75);   
          /* Set speed of motor 1 to 50 % */
          motor->SetSpeed(1,50);             
          break;      
        case 8:
          printf("STEP 8: Motor(0) BWD Speed=100%% - Motor(1) FWD Speed=75%%\r\n");
          /* Set speed of motor 0 to 100 % */
          motor->SetSpeed(0,100);   
          /* Set speed of motor 1 to 75 % */
          motor->SetSpeed(1,75);   
          break;  
        case 9:
          printf("STEP 9: Motor(0) BWD Speed=100%% - Motor(1) FWD Speed=100%%\r\n");
          /* Set speed of motor 1 to 100 % */
          motor->SetSpeed(1,100);    
          break;   
        case 10:
          printf("STEP 10\r\n: Stop both motors and disable bridges\r\n");
          /* Stop both motors and disable bridge */
          motor->HardHiZ(0);    
          motor->HardHiZ(1);    
          break;           
        case 11:
          printf("STEP 11: Motor(0) FWD Speed=100%% - Motor(1) FWD Speed=100%%\r\n");
          /* Start both motors to go forward*/
          motor->Run(0,BDCMotor::FWD);    
          motor->Run(1,BDCMotor::FWD);    
          break;                 
        case 12:
        default:
          printf("STEP 12: Stop both motors and enter standby mode\r\n");
          /* Stop both motors and put chip in standby mode */
          motor->Reset();    
          break;            
    }
  
    /* Wait for 5 seconds */  
    wait_ms(5000);
    
    /* Increment demostep*/  
    demoStep++;
    if (demoStep > 12)
    {
      demoStep = 0;
    }
  } 
}
/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/