stm32f1xx_hal_conf.h

00001 /**
00002   ******************************************************************************
00003   * @file    stm32f1xx_hal_conf.h
00004   * @author  MCD Application Team
00005   * @version V1.0.4
00006   * @date    29-April-2016
00007   * @brief   HAL configuration template file.
00008   *          This file should be copied to the application folder and renamed
00009   *          to stm32f1xx_hal_conf.h.
00010   ******************************************************************************
00011   * @attention
00012   *
00013   * <h2><center>&copy; COPYRIGHT(c) 2016 STMicroelectronics</center></h2>
00014   *
00015   * Redistribution and use in source and binary forms, with or without modification,
00016   * are permitted provided that the following conditions are met:
00017   *   1. Redistributions of source code must retain the above copyright notice,
00018   *      this list of conditions and the following disclaimer.
00019   *   2. Redistributions in binary form must reproduce the above copyright notice,
00020   *      this list of conditions and the following disclaimer in the documentation
00021   *      and/or other materials provided with the distribution.
00022   *   3. Neither the name of STMicroelectronics nor the names of its contributors
00023   *      may be used to endorse or promote products derived from this software
00024   *      without specific prior written permission.
00025   *
00026   * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
00027   * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
00028   * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
00029   * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
00030   * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
00031   * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
00032   * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
00033   * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
00034   * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
00035   * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
00036   *
00037   ******************************************************************************
00038   */ 
00039 
00040 /* Define to prevent recursive inclusion -------------------------------------*/
00041 #ifndef __STM32F1xx_HAL_CONF_H
00042 #define __STM32F1xx_HAL_CONF_H
00043 
00044 #ifdef __cplusplus
00045  extern "C" {
00046 #endif
00047 
00048 /* Exported types ------------------------------------------------------------*/
00049 /* Exported constants --------------------------------------------------------*/
00050 
00051 /* ########################## Module Selection ############################## */
00052 /**
00053   * @brief This is the list of modules to be used in the HAL driver 
00054   */
00055 #define HAL_MODULE_ENABLED
00056 //#define HAL_ADC_MODULE_ENABLED
00057 //#define HAL_CAN_MODULE_ENABLED
00058 //#define HAL_CEC_MODULE_ENABLED
00059 #define HAL_CORTEX_MODULE_ENABLED
00060 //#define HAL_CRC_MODULE_ENABLED
00061 //#define HAL_DAC_MODULE_ENABLED
00062 #define HAL_DMA_MODULE_ENABLED
00063 //#define HAL_ETH_MODULE_ENABLED
00064 #define HAL_FLASH_MODULE_ENABLED
00065 #define HAL_GPIO_MODULE_ENABLED
00066 //#define HAL_HCD_MODULE_ENABLED
00067 //#define HAL_I2C_MODULE_ENABLED
00068 //#define HAL_I2S_MODULE_ENABLED
00069 //#define HAL_IRDA_MODULE_ENABLED
00070 //#define HAL_IWDG_MODULE_ENABLED
00071 //#define HAL_NAND_MODULE_ENABLED
00072 //#define HAL_NOR_MODULE_ENABLED
00073 //#define HAL_PCCARD_MODULE_ENABLED
00074 //#define HAL_PCD_MODULE_ENABLED
00075 //#define HAL_PWR_MODULE_ENABLED
00076 #define HAL_RCC_MODULE_ENABLED
00077 //#define HAL_RTC_MODULE_ENABLED
00078 //#define HAL_SD_MODULE_ENABLED
00079 //#define HAL_SMARTCARD_MODULE_ENABLED
00080 //#define HAL_SPI_MODULE_ENABLED
00081 //#define HAL_SRAM_MODULE_ENABLED
00082 #define HAL_TIM_MODULE_ENABLED
00083 #define HAL_UART_MODULE_ENABLED
00084 #define HAL_USART_MODULE_ENABLED
00085 //#define HAL_WWDG_MODULE_ENABLED
00086 
00087 /* ########################## Oscillator Values adaptation ####################*/
00088 /**
00089   * @brief Adjust the value of External High Speed oscillator (HSE) used in your application.
00090   *        This value is used by the RCC HAL module to compute the system frequency
00091   *        (when HSE is used as system clock source, directly or through the PLL).  
00092   */
00093 #if !defined  (HSE_VALUE) 
00094 #if defined(USE_STM3210C_EVAL)
00095   #define HSE_VALUE    ((uint32_t)25000000) /*!< Value of the External oscillator in Hz */
00096 #else
00097   #define HSE_VALUE    ((uint32_t)8000000) /*!< Value of the External oscillator in Hz */
00098 #endif
00099 #endif /* HSE_VALUE */
00100 
00101 #if !defined  (HSE_STARTUP_TIMEOUT)
00102   #define HSE_STARTUP_TIMEOUT    ((uint32_t)100)   /*!< Time out for HSE start up, in ms */
00103 #endif /* HSE_STARTUP_TIMEOUT */
00104 
00105 /**
00106   * @brief Internal High Speed oscillator (HSI) value.
00107   *        This value is used by the RCC HAL module to compute the system frequency
00108   *        (when HSI is used as system clock source, directly or through the PLL). 
00109   */
00110 #if !defined  (HSI_VALUE)
00111   #define HSI_VALUE    ((uint32_t)8000000) /*!< Value of the Internal oscillator in Hz*/
00112 #endif /* HSI_VALUE */
00113 
00114 /**
00115   * @brief External Low Speed oscillator (LSE) value.
00116   *        This value is used by the UART, RTC HAL module to compute the system frequency
00117   */
00118 #if !defined  (LSE_VALUE)
00119   #define LSE_VALUE    ((uint32_t)32768) /*!< Value of the External oscillator in Hz*/
00120 #endif /* LSE_VALUE */
00121 
00122    
00123 #if !defined  (LSE_STARTUP_TIMEOUT)
00124   #define LSE_STARTUP_TIMEOUT    ((uint32_t)5000)   /*!< Time out for LSE start up, in ms */
00125 #endif /* HSE_STARTUP_TIMEOUT */
00126 
00127    
00128 /* Tip: To avoid modifying this file each time you need to use different HSE,
00129    ===  you can define the HSE value in your toolchain compiler preprocessor. */
00130 
00131 /* ########################### System Configuration ######################### */
00132 /**
00133   * @brief This is the HAL system configuration section
00134   */     
00135 #define  VDD_VALUE                    ((uint32_t)3300) /*!< Value of VDD in mv */           
00136 #define  TICK_INT_PRIORITY            ((uint32_t)0x000F)    /*!< tick interrupt priority */            
00137 #define  USE_RTOS                     0     
00138 #define  PREFETCH_ENABLE              1
00139 
00140 /* ########################## Assert Selection ############################## */
00141 /**
00142   * @brief Uncomment the line below to expanse the "assert_param" macro in the 
00143   *        HAL drivers code
00144   */
00145 /*#define USE_FULL_ASSERT    1*/ 
00146 
00147 
00148 /* ################## Ethernet peripheral configuration ##################### */
00149 
00150 /* Section 1 : Ethernet peripheral configuration */
00151 
00152 /* MAC ADDRESS: MAC_ADDR0:MAC_ADDR1:MAC_ADDR2:MAC_ADDR3:MAC_ADDR4:MAC_ADDR5 */
00153 #define MAC_ADDR0   2
00154 #define MAC_ADDR1   0
00155 #define MAC_ADDR2   0
00156 #define MAC_ADDR3   0
00157 #define MAC_ADDR4   0
00158 #define MAC_ADDR5   0
00159 
00160 /* Definition of the Ethernet driver buffers size and count */   
00161 #define ETH_RX_BUF_SIZE                ETH_MAX_PACKET_SIZE /* buffer size for receive               */
00162 #define ETH_TX_BUF_SIZE                ETH_MAX_PACKET_SIZE /* buffer size for transmit              */
00163 #define ETH_RXBUFNB                    ((uint32_t)8)       /* 4 Rx buffers of size ETH_RX_BUF_SIZE  */
00164 #define ETH_TXBUFNB                    ((uint32_t)4)       /* 4 Tx buffers of size ETH_TX_BUF_SIZE  */
00165 
00166 /* Section 2: PHY configuration section */
00167 
00168 /* DP83848 PHY Address*/ 
00169 #define DP83848_PHY_ADDRESS             0x01
00170 /* PHY Reset delay these values are based on a 1 ms Systick interrupt*/ 
00171 #define PHY_RESET_DELAY                 ((uint32_t)0x000000FF)
00172 /* PHY Configuration delay */
00173 #define PHY_CONFIG_DELAY                ((uint32_t)0x00000FFF)
00174 
00175 #define PHY_READ_TO                     ((uint32_t)0x0000FFFF)
00176 #define PHY_WRITE_TO                    ((uint32_t)0x0000FFFF)
00177 
00178 /* Section 3: Common PHY Registers */
00179 
00180 #define PHY_BCR                         ((uint16_t)0x00)    /*!< Transceiver Basic Control Register   */
00181 #define PHY_BSR                         ((uint16_t)0x01)    /*!< Transceiver Basic Status Register    */
00182  
00183 #define PHY_RESET                       ((uint16_t)0x8000)  /*!< PHY Reset */
00184 #define PHY_LOOPBACK                    ((uint16_t)0x4000)  /*!< Select loop-back mode */
00185 #define PHY_FULLDUPLEX_100M             ((uint16_t)0x2100)  /*!< Set the full-duplex mode at 100 Mb/s */
00186 #define PHY_HALFDUPLEX_100M             ((uint16_t)0x2000)  /*!< Set the half-duplex mode at 100 Mb/s */
00187 #define PHY_FULLDUPLEX_10M              ((uint16_t)0x0100)  /*!< Set the full-duplex mode at 10 Mb/s  */
00188 #define PHY_HALFDUPLEX_10M              ((uint16_t)0x0000)  /*!< Set the half-duplex mode at 10 Mb/s  */
00189 #define PHY_AUTONEGOTIATION             ((uint16_t)0x1000)  /*!< Enable auto-negotiation function     */
00190 #define PHY_RESTART_AUTONEGOTIATION     ((uint16_t)0x0200)  /*!< Restart auto-negotiation function    */
00191 #define PHY_POWERDOWN                   ((uint16_t)0x0800)  /*!< Select the power down mode           */
00192 #define PHY_ISOLATE                     ((uint16_t)0x0400)  /*!< Isolate PHY from MII                 */
00193 
00194 #define PHY_AUTONEGO_COMPLETE           ((uint16_t)0x0020)  /*!< Auto-Negotiation process completed   */
00195 #define PHY_LINKED_STATUS               ((uint16_t)0x0004)  /*!< Valid link established               */
00196 #define PHY_JABBER_DETECTION            ((uint16_t)0x0002)  /*!< Jabber condition detected            */
00197   
00198 /* Section 4: Extended PHY Registers */
00199 
00200 #define PHY_SR                          ((uint16_t)0x10)    /*!< PHY status register Offset                      */
00201 #define PHY_MICR                        ((uint16_t)0x11)    /*!< MII Interrupt Control Register                  */
00202 #define PHY_MISR                        ((uint16_t)0x12)    /*!< MII Interrupt Status and Misc. Control Register */
00203  
00204 #define PHY_LINK_STATUS                 ((uint16_t)0x0001)  /*!< PHY Link mask                                   */
00205 #define PHY_SPEED_STATUS                ((uint16_t)0x0002)  /*!< PHY Speed mask                                  */
00206 #define PHY_DUPLEX_STATUS               ((uint16_t)0x0004)  /*!< PHY Duplex mask                                 */
00207 
00208 #define PHY_MICR_INT_EN                 ((uint16_t)0x0002)  /*!< PHY Enable interrupts                           */
00209 #define PHY_MICR_INT_OE                 ((uint16_t)0x0001)  /*!< PHY Enable output interrupt events              */
00210 
00211 #define PHY_MISR_LINK_INT_EN            ((uint16_t)0x0020)  /*!< Enable Interrupt on change of link status       */
00212 #define PHY_LINK_INTERRUPT              ((uint16_t)0x2000)  /*!< PHY link status interrupt mask                  */
00213 
00214 
00215 
00216 /* Includes ------------------------------------------------------------------*/
00217 /**
00218   * @brief Include module's header file 
00219   */
00220 
00221 #ifdef HAL_RCC_MODULE_ENABLED
00222  #include "stm32f1xx_hal_rcc.h"
00223 #endif /* HAL_RCC_MODULE_ENABLED */
00224 
00225 #ifdef HAL_GPIO_MODULE_ENABLED
00226  #include "stm32f1xx_hal_gpio.h"
00227 #endif /* HAL_GPIO_MODULE_ENABLED */
00228    
00229 #ifdef HAL_DMA_MODULE_ENABLED
00230   #include "stm32f1xx_hal_dma.h"
00231 #endif /* HAL_DMA_MODULE_ENABLED */
00232    
00233 #ifdef HAL_ETH_MODULE_ENABLED
00234   #include "stm32f1xx_hal_eth.h"
00235 #endif /* HAL_ETH_MODULE_ENABLED */  
00236    
00237 #ifdef HAL_CAN_MODULE_ENABLED
00238  #include "stm32f1xx_hal_can.h"
00239 #endif /* HAL_CAN_MODULE_ENABLED */
00240 
00241 #ifdef HAL_CEC_MODULE_ENABLED
00242  #include "stm32f1xx_hal_cec.h"
00243 #endif /* HAL_CEC_MODULE_ENABLED */
00244 
00245 #ifdef HAL_CORTEX_MODULE_ENABLED
00246  #include "stm32f1xx_hal_cortex.h"
00247 #endif /* HAL_CORTEX_MODULE_ENABLED */
00248 
00249 #ifdef HAL_ADC_MODULE_ENABLED
00250  #include "stm32f1xx_hal_adc.h"
00251 #endif /* HAL_ADC_MODULE_ENABLED */
00252 
00253 #ifdef HAL_CRC_MODULE_ENABLED
00254  #include "stm32f1xx_hal_crc.h"
00255 #endif /* HAL_CRC_MODULE_ENABLED */
00256 
00257 #ifdef HAL_DAC_MODULE_ENABLED
00258  #include "stm32f1xx_hal_dac.h"
00259 #endif /* HAL_DAC_MODULE_ENABLED */
00260 
00261 #ifdef HAL_FLASH_MODULE_ENABLED
00262  #include "stm32f1xx_hal_flash.h"
00263 #endif /* HAL_FLASH_MODULE_ENABLED */
00264 
00265 #ifdef HAL_SRAM_MODULE_ENABLED
00266  #include "stm32f1xx_hal_sram.h"
00267 #endif /* HAL_SRAM_MODULE_ENABLED */
00268 
00269 #ifdef HAL_NOR_MODULE_ENABLED
00270  #include "stm32f1xx_hal_nor.h"
00271 #endif /* HAL_NOR_MODULE_ENABLED */
00272 
00273 #ifdef HAL_I2C_MODULE_ENABLED
00274  #include "stm32f1xx_hal_i2c.h"
00275 #endif /* HAL_I2C_MODULE_ENABLED */
00276 
00277 #ifdef HAL_I2S_MODULE_ENABLED
00278  #include "stm32f1xx_hal_i2s.h"
00279 #endif /* HAL_I2S_MODULE_ENABLED */
00280 
00281 #ifdef HAL_IWDG_MODULE_ENABLED
00282  #include "stm32f1xx_hal_iwdg.h"
00283 #endif /* HAL_IWDG_MODULE_ENABLED */
00284 
00285 #ifdef HAL_PWR_MODULE_ENABLED
00286  #include "stm32f1xx_hal_pwr.h"
00287 #endif /* HAL_PWR_MODULE_ENABLED */
00288 
00289 #ifdef HAL_RTC_MODULE_ENABLED
00290  #include "stm32f1xx_hal_rtc.h"
00291 #endif /* HAL_RTC_MODULE_ENABLED */
00292 
00293 #ifdef HAL_PCCARD_MODULE_ENABLED
00294  #include "stm32f1xx_hal_pccard.h"
00295 #endif /* HAL_PCCARD_MODULE_ENABLED */ 
00296 
00297 #ifdef HAL_SD_MODULE_ENABLED
00298  #include "stm32f1xx_hal_sd.h"
00299 #endif /* HAL_SD_MODULE_ENABLED */  
00300 
00301 #ifdef HAL_NAND_MODULE_ENABLED
00302  #include "stm32f1xx_hal_nand.h"
00303 #endif /* HAL_NAND_MODULE_ENABLED */     
00304 
00305 #ifdef HAL_SPI_MODULE_ENABLED
00306  #include "stm32f1xx_hal_spi.h"
00307 #endif /* HAL_SPI_MODULE_ENABLED */
00308 
00309 #ifdef HAL_TIM_MODULE_ENABLED
00310  #include "stm32f1xx_hal_tim.h"
00311 #endif /* HAL_TIM_MODULE_ENABLED */
00312 
00313 #ifdef HAL_UART_MODULE_ENABLED
00314  #include "stm32f1xx_hal_uart.h"
00315 #endif /* HAL_UART_MODULE_ENABLED */
00316 
00317 #ifdef HAL_USART_MODULE_ENABLED
00318  #include "stm32f1xx_hal_usart.h"
00319 #endif /* HAL_USART_MODULE_ENABLED */
00320 
00321 #ifdef HAL_IRDA_MODULE_ENABLED
00322  #include "stm32f1xx_hal_irda.h"
00323 #endif /* HAL_IRDA_MODULE_ENABLED */
00324 
00325 #ifdef HAL_SMARTCARD_MODULE_ENABLED
00326  #include "stm32f1xx_hal_smartcard.h"
00327 #endif /* HAL_SMARTCARD_MODULE_ENABLED */
00328 
00329 #ifdef HAL_WWDG_MODULE_ENABLED
00330  #include "stm32f1xx_hal_wwdg.h"
00331 #endif /* HAL_WWDG_MODULE_ENABLED */
00332 
00333 #ifdef HAL_PCD_MODULE_ENABLED
00334  #include "stm32f1xx_hal_pcd.h"
00335 #endif /* HAL_PCD_MODULE_ENABLED */
00336 
00337 
00338 #ifdef HAL_HCD_MODULE_ENABLED
00339  #include "stm32f1xx_hal_hcd.h"
00340 #endif /* HAL_HCD_MODULE_ENABLED */   
00341    
00342 
00343 /* Exported macro ------------------------------------------------------------*/
00344 #ifdef  USE_FULL_ASSERT
00345 /**
00346   * @brief  The assert_param macro is used for function's parameters check.
00347   * @param  expr: If expr is false, it calls assert_failed function
00348   *         which reports the name of the source file and the source
00349   *         line number of the call that failed. 
00350   *         If expr is true, it returns no value.
00351   * @retval None
00352   */
00353   #define assert_param(expr) ((expr) ? (void)0 : assert_failed((uint8_t *)__FILE__, __LINE__))
00354 /* Exported functions ------------------------------------------------------- */
00355   void assert_failed(uint8_t* file, uint32_t line);
00356 #else
00357   #define assert_param(expr) ((void)0)
00358 #endif /* USE_FULL_ASSERT */
00359 
00360 #ifdef __cplusplus
00361 }
00362 #endif
00363 
00364 #endif /* __STM32F1xx_HAL_CONF_H */
00365 
00366 
00367 /************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/