Analog Devices
/
EVAL-CN0540-ARDZ
Important changes to repositories hosted on mbed.com
Mbed hosted mercurial repositories are deprecated and are due to be permanently deleted in July 2026.
To keep a copy of this software download the repository Zip archive or clone locally using Mercurial.
It is also possible to export all your personal repositories from the account settings page.
Dependencies: platform_drivers LTC26X6 AD77681
main.cpp
- Committer:
- jngarlitos
- Date:
- 2021-12-06
- Revision:
- 1:9dd7c64b4a64
- Parent:
- 0:b9debc14d077
File content as of revision 1:9dd7c64b4a64:
/******************************************************************************
*Copyright (c)2020 Analog Devices, Inc.
*
* Licensed under the 2020-04-27-CN0540EC License(the "License");
* you may not use this file except in compliance with the License.
*
****************************************************************************/
#include <mbed.h>
#include "platform_drivers.h"
#include <assert.h>
#include "main.h"
#include "cn0540_app_config.h"
#include "platform_drivers.h"
#include "cn0540_init_params.h"
extern "C"{
#include "ad77681.h"
#include "cn0540_adi_fft.h"
#include "ltc26x6.h"
}
// Descriptor of the main device - the ADC AD7768-1
ad77681_dev *device_adc;
// Structure carying measured data, sampled by the ADC
adc_data measured_data;
// AD7768-1's status register structure, carying all the error flags
ad77681_status_registers *current_status;
// Initialize the interrupt event variable
volatile bool int_event= false;
// Descriptor of the DAC LTC2606
ltc26x6_dev *device_dac;
// Structure carying data, the FFT module works with
fft_entry *FFT_data;
// Structure carying measuremtns from the FFT module
fft_measurements *FFT_meas;
// Initialize the serial object with TX and RX pins
Serial pc(USBTX, USBRX);
// Initialize the drdy pin as interrupt input
InterruptIn drdy(DRDY_PIN, PullNone);
// Initialize the adc_rst_pin pin as digital output
DigitalOut adc_reset(ADC_RST_PIN);
// Initialize the buffer enable control pin as digital output
DigitalOut buffer_en(ARD_BUF_EN_PIN);
// Initialize the red LED control pin as digital output
DigitalOut led_red(ARD_RED_LED_PIN);
// Initialize the blue LED pin as digital output
DigitalOut led_blue(ARD_BLUE_LED_PIN);
/**
* ADC data recteption interrupt from DRDY
*
* Data reception from the ADC using interrupt generated by the ADC's DRDY (Data Ready) pin
* Interrupt triggers falling edge of the active-high DRDY pulse
* DRDY pulse is generated by the ADC and frequency of the DRDY pulse depends on the ADC settings:
*
* DRDY frequency = MCLK / ( MCLK_DIV * FILTER_OSR )
*/
void drdy_interrupt()
{
int_event = true;
if (measured_data.count == measured_data.samples) { // Desired numer of samples has been taken, set everything back
drdy.disable_irq(); // Disable interrupt on DRDY pin
measured_data.finish = true; // Desired number of samples has been taken
measured_data.count = 0; // Set measured data counter to 0
}
}
/**
*=================================================================================================================================
*
* ////////////////////////////////////////////////// MAIN function \\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\
*
*==================================================================================================================================
*/
int main() {
int32_t connected = FAILURE;
uint32_t menu;
sdpk1_gpio_setup(); // Setup SDP-K1 GPIOs
adc_hard_reset(); // Perform ADC hard reset
connected = ad77681_setup(&device_adc, init_params, ¤t_status); // SETUP and check connection
if(connected == FAILURE)
go_to_error();
ltc26x6_init(&device_dac, init_params_dac); // Initialize DAC
#ifdef CN0540_ADI_FFT_H_ // if the adi_fft.h is included , initialize it
FFT_init_params(&FFT_data, &FFT_meas); // Initialize FFT structure and allocate space
update_FFT_enviroment(device_adc->vref, device_adc->mclk, device_adc->sample_rate, FFT_data); // Update the Vref, Mclk, Sampling rate
measured_data.samples = 4096; // Initialize FFT with 4096 samples
FFT_init(measured_data.samples, FFT_data); // Update sample count for FFT
#endif // CN0540_ADI_FFT_H_ // FFT module is initializedd with 4096 samples and 7-term BH window
print_title();
print_prompt();
//============ MAIN WHILE ====================//
while(1)
{
if (pc.readable()) { // Settings menu SWITCH
getUserInput(&menu);
switch (menu) {
case 1:
menu_1_set_adc_powermode(); // Set ADC power mode
break;
case 2:
menu_2_set_adc_clock_divider(); // Set ADC clock divider
break;
case 3:
menu_3_set_adc_filter_type(); // Set ad7768-1 filter type
break;
case 4:
menu_4_adc_buffers_controll(); // Set ADC AIN & Reference buffers
break;
case 5:
menu_5_set_default_settings(); // Set ADC default value
break;
case 6:
menu_6_set_adc_vcm(); // Set ADC VCM
break;
case 7:
menu_7_adc_read_register(); // Read ADC register
break;
case 8:
menu_8_adc_cont_read_data(); // Perform continuous ADC read
break;
case 9:
menu_9_reset_ADC(); // Reset ADC
break;
case 10:
menu_10_power_down(); // ADC Wake up and sleep
break;
case 11:
menu_11_ADC_GPIO(); // Set ADC GPIOs
break;
case 12:
menu_12_read_master_status(); // Read ADC master status
break;
case 13:
menu_13_mclk_vref(); // Set ADC MCLK / Vref
break;
case 14:
menu_14_print_measured_data(); // Print continouos ADC read data
break;
case 15:
menu_15_set_adc_data_output_mode(); // Set ADC data output mode
break;
case 16:
menu_16_set_adc_diagnostic_mode(); // Set ADC to diagnostic mode
break;
case 17:
menu_17_do_the_fft(); // Perform FFT
break;
case 18:
menu_18_fft_settings(); // Change FFT settins
break;
case 19:
menu_19_gains_offsets(); // Set ADC gain and offset
break;
case 20:
menu_20_check_scratchpad(); // Perform scratchpad check
break;
case 21:
menu_21_piezo_offset(); // Compensate piezo offset
break;
case 22:
menu_22_set_DAC_output(); // Set DAC output mode
break;
default:
pc.printf("Invalid option");
print_prompt();
break;
}
}
}
}
/**
* Error warning, in case of unsuccessfull SPI connection
*
*/
void static go_to_error()
{
int32_t connected = FAILURE;
uint8_t scratchpad_sequence = 0xAD;
while (1) {
pc.printf("ERROR: NOT CONNECTED\nCHECK YOUR PHYSICAL CONNECTION\n\n"); // When not connected, keep showing error message
wait(5);
connected = ad77681_setup(&device_adc, init_params, ¤t_status); // Keep trying to connect
if (connected == SUCCESS) {
pc.printf("SUCCESSFULLY RECONNECTED\n\n"); // If successfull reading from scratchpad, init the ADC and go back
break;
}
}
}
/**
* Print title
*
*/
void static print_title() {
pc.printf("\n\r");
pc.printf("****************************************************************\n");
pc.printf("* EVAL-CN0540-PMDZ Demonstration Program -- (mbed) *\n");
pc.printf("* *\n");
pc.printf("* This program demonstrates IEPE / ICP piezo accelerometer *\n");
pc.printf("* interfacing and FFT measurements using AD7768-1 *\n");
pc.printf("* Precision 24-bit sigma-delta AD converter *\n");
pc.printf("* *\n");
pc.printf("* Set the baud rate to 115200 select the newline terminator. *\n");
pc.printf("****************************************************************\n");
}
/**
* Print main menu to console
*
*/
void static print_prompt() {
pc.printf("\n\nCommand Summary:\n\n");
pc.printf(" 1 - Set ADC power mode\n");
pc.printf(" 2 - Set ADC MCLK divider\n");
pc.printf(" 3 - Set ADC filter type\n");
pc.printf(" 4 - Set ADC AIN and REF buffers\n");
pc.printf(" 5 - Set ADC to default config\n");
pc.printf(" 6 - Set ADC VCM output\n");
pc.printf(" 7 - Read desired ADC register\n");
pc.printf(" 8 - Read continuous ADC data\n");
pc.printf(" 9 - Reset ADC\n");
pc.printf(" 10 - ADC Power-down\n");
pc.printf(" 11 - Set ADC GPIOs\n");
pc.printf(" 12 - Read ADC master status\n");
pc.printf(" 13 - Set ADC Vref and MCLK\n");
pc.printf(" 14 - Print ADC measured data\n");
pc.printf(" 15 - Set ADC data output mode\n");
pc.printf(" 16 - Set ADC diagnostic mode\n");
pc.printf(" 17 - Do the FFT\n");
pc.printf(" 18 - FFT settings\n");
pc.printf(" 19 - Set ADC Gains, Offsets\n");
pc.printf(" 20 - ADC Scratchpad Check\n");
pc.printf(" 21 - Compenzate Piezo sensor offset\n");
pc.printf(" 22 - Set DAC output\n");
pc.printf("\n\r");
}
/**
* Read user input from uart
* *UserInput = 0 if failure
*
*/
int32_t static getUserInput(uint32_t *UserInput)
{
long uart_val;
int32_t ret;
ret = pc.scanf("%ld", &uart_val); // Return 1 = OK, Return 0 = Fail
if((ret == 0) || (uart_val < 0)) { // Failure if uart_val is negative, or non-digit
*UserInput = 0;
return FAILURE;
}
*UserInput = (uint32_t)(uart_val);
return SUCCESS;
}
/**
* Set power mode
*
*/
void static menu_1_set_adc_powermode(void)
{
uint32_t new_pwr_mode;
pc.printf(" Avaliable power modes: \n");
pc.printf(" 1 - Low power mode\n");
pc.printf(" 2 - Median power mode\n");
pc.printf(" 3 - Fast power mode\n");
pc.printf(" Select an option: \n");
getUserInput(&new_pwr_mode);
pc.putc('\n');
switch (new_pwr_mode) {
case 1:
ad77681_set_power_mode(device_adc, AD77681_ECO);
pc.printf(" Low power mode selected\n");
break;
case 2:
ad77681_set_power_mode(device_adc, AD77681_MEDIAN);
pc.printf(" Median power mode selected\n");
break;
case 3:
ad77681_set_power_mode(device_adc, AD77681_FAST);
pc.printf(" Fast power mode selected\n");
break;
default:
pc.printf(" Invalid option\n");
break;
}
print_prompt();
}
/**
* Set clock divider
*
*/
void static menu_2_set_adc_clock_divider(void)
{
uint32_t new_mclk_div;
pc.printf(" Avaliable MCLK divide options: \n");
pc.printf(" 1 - MCLK/16\n");
pc.printf(" 2 - MCLK/8\n");
pc.printf(" 3 - MCLK/4\n");
pc.printf(" 4 - MCLK/2\n");
pc.printf(" Select an option: \n");
getUserInput(&new_mclk_div);
pc.putc('\n');
switch (new_mclk_div) {
case 1:
ad77681_set_mclk_div(device_adc, AD77681_MCLK_DIV_16);
pc.printf(" MCLK/16 selected\n");
break;
case 2:
ad77681_set_mclk_div(device_adc, AD77681_MCLK_DIV_8);
pc.printf(" MCLK/8 selected\n");
break;
case 3:
ad77681_set_mclk_div(device_adc, AD77681_MCLK_DIV_4);
pc.printf(" MCLK/4 selected\n");
break;
case 4:
ad77681_set_mclk_div(device_adc, AD77681_MCLK_DIV_2);
pc.printf(" MCLK/2 selected\n");
break;
default:
pc.printf(" Invalid option\n");
break;
}
// Update the sample rate after changing the MCLK divider
ad77681_update_sample_rate(device_adc);
print_prompt();
}
/**
* Set filter type
*
*/
void static menu_3_set_adc_filter_type(void)
{
uint32_t new_filter = 0;
int32_t ret;
pc.printf(" Avaliable clock divide options: \n");
pc.printf(" 1 - SINC3 Fileter\n");
pc.printf(" 2 - SINC5 Filter\n");
pc.printf(" 3 - Low ripple FIR Filter\n");
pc.printf(" 4 - SINC3 50/60Hz rejection\n");
pc.printf(" 5 - User-defined FIR filter\n");
pc.printf(" Select an option: \n");
getUserInput(&new_filter);
pc.putc('\n');
switch (new_filter) {
case 1:
set_adc_SINC3_filter();
break;
case 2:
set_adc_SINC5_filter();
break;
case 3:
set_adc_FIR_filter();
break;
case 4:
set_adc_50HZ_rej();
break;
case 5:
set_adc_user_defined_FIR();
break;
default:
pc.printf(" Invalid option\n");
break;
}
// Update the sample rate after changing the Filter type
ad77681_update_sample_rate(device_adc);
print_prompt();
}
/**
* Set SINC3 filter
*
*/
void static set_adc_SINC3_filter(void)
{
uint32_t new_sinc3 = 0, new_sinc5 = 0;
int32_t ret;
pc.printf(" SINC3 filter Oversampling ratios: \n");
pc.printf(" OSR is calculated as (x + 1)*32\n");
pc.printf(" x is SINC3 OSR register value\n");
pc.printf(" Please input a value from 0 to 8192 = 2^13\n :");
ret = getUserInput(&new_sinc3);
if ((new_sinc3 >= 0) && (new_sinc3 <= 8192) && (ret == SUCCESS)) {
pc.printf("%d\n", new_sinc3);
ad77681_set_filter_type(device_adc, AD77681_SINC5_FIR_DECx32, AD77681_SINC3, new_sinc3);
pc.printf(" SINC3 OSR is set to %d\n", (new_sinc3 + 1) * 32);
} else {
pc.printf("%d\n", new_sinc3);
pc.printf(" Invalid option - too large number\n");
}
}
/**
* Set SINC5 filter
*
*/
void static set_adc_SINC5_filter(void)
{
uint32_t new_sinc5;
pc.printf(" SINC5 filter Oversampling ratios: \n");
pc.printf(" 1 - Oversampled by 8\n");
pc.printf(" 2 - Oversampled by 16\n");
pc.printf(" 3 - Oversampled by 32\n");
pc.printf(" 4 - Oversampled by 64\n");
pc.printf(" 5 - Oversampled by 128\n");
pc.printf(" 6 - Oversampled by 256\n");
pc.printf(" 7 - Oversampled by 512\n");
pc.printf(" 8 - Oversampled by 1024\n");
pc.printf(" Select an option: \n");
getUserInput(&new_sinc5);
pc.putc('\n');
switch (new_sinc5) {
case 1:
ad77681_set_filter_type(device_adc, AD77681_SINC5_FIR_DECx32, AD77681_SINC5_DECx8, 0);
pc.printf(" SINC5 with OSRx8 set\n");
break;
case 2:
ad77681_set_filter_type(device_adc, AD77681_SINC5_FIR_DECx32, AD77681_SINC5_DECx16, 0);
pc.printf(" SINC5 with OSRx16 set\n");
break;
case 3:
ad77681_set_filter_type(device_adc, AD77681_SINC5_FIR_DECx32, AD77681_SINC5, 0);
pc.printf(" SINC5 with OSRx32 set\n");
break;
case 4:
ad77681_set_filter_type(device_adc, AD77681_SINC5_FIR_DECx64, AD77681_SINC5, 0);
pc.printf(" SINC5 with OSRx64 set\n");
break;
case 5:
ad77681_set_filter_type(device_adc, AD77681_SINC5_FIR_DECx128, AD77681_SINC5, 0);
pc.printf(" SINC5 with OSRx128 set\n");
break;
case 6:
ad77681_set_filter_type(device_adc, AD77681_SINC5_FIR_DECx256, AD77681_SINC5, 0);
pc.printf(" SINC5 with OSRx256 set\n");
break;
case 7:
ad77681_set_filter_type(device_adc, AD77681_SINC5_FIR_DECx512, AD77681_SINC5, 0);
pc.printf(" SINC5 with OSRx512 set\n");
break;
case 8:
ad77681_set_filter_type(device_adc, AD77681_SINC5_FIR_DECx1024, AD77681_SINC5, 0);
pc.printf(" SINC5 with OSRx1024 set\n");
break;
default:
pc.printf(" Invalid option\n");
break;
}
}
/**
* Set FIR filter
*
*/
void static set_adc_FIR_filter(void)
{
uint32_t new_fir;
pc.printf(" FIR filter Oversampling ratios: \n");
pc.printf(" 1 - Oversampled by 32\n");
pc.printf(" 2 - Oversampled by 64\n");
pc.printf(" 3 - Oversampled by 128\n");
pc.printf(" 4 - Oversampled by 256\n");
pc.printf(" 5 - Oversampled by 512\n");
pc.printf(" 6 - Oversampled by 1024\n");
pc.printf(" Select an option: \n");
getUserInput(&new_fir);
pc.putc('\n');
switch (new_fir) {
case 1:
ad77681_set_filter_type(device_adc, AD77681_SINC5_FIR_DECx32, AD77681_FIR, 0);
pc.printf(" FIR with OSRx32 set\n");
break;
case 2:
ad77681_set_filter_type(device_adc, AD77681_SINC5_FIR_DECx64, AD77681_FIR, 0);
pc.printf(" FIR with OSRx64 set\n");
break;
case 3:
ad77681_set_filter_type(device_adc, AD77681_SINC5_FIR_DECx128, AD77681_FIR, 0);
pc.printf(" FIR with OSRx128 set\n");
break;
case 4:
ad77681_set_filter_type(device_adc, AD77681_SINC5_FIR_DECx256, AD77681_FIR, 0);
pc.printf(" FIR with OSRx256 set\n");
break;
case 5:
ad77681_set_filter_type(device_adc, AD77681_SINC5_FIR_DECx512, AD77681_FIR, 0);
pc.printf(" FIR with OSRx512 set\n");
break;
case 6:
ad77681_set_filter_type(device_adc, AD77681_SINC5_FIR_DECx1024, AD77681_FIR, 0);
pc.printf(" FIR with OSRx1024 set\n");
break;
default:
pc.printf(" Invalid option\n");
break;
}
}
/**
* Set 50HZ rejection bit when SINC3 is being used
*
*/
void static set_adc_50HZ_rej(void)
{
uint32_t new_50Hz;
pc.printf(" SINC3 50/60Hz rejection: \n");
pc.printf(" 1 - 50/60Hz rejection enable \n");
pc.printf(" 2 - 50/60Hz rejection disable \n");
pc.printf(" Select an option: \n");
getUserInput(&new_50Hz);
pc.putc('\n');
switch (new_50Hz)
{
case 1:
ad77681_set_50HZ_rejection(device_adc, ENABLE);
pc.printf(" SINC3 50/60Hz rejection enabled\n");
break;
case 2:
ad77681_set_50HZ_rejection(device_adc, DISABLE);
pc.printf(" SINC3 50/60Hz rejection disabled\n");
break;
default:
pc.printf(" Invalid option\n");
break;
}
}
/**
* Insert user-defined FIR filter coeffs
*
*/
void static set_adc_user_defined_FIR(void)
{
const uint8_t coeff_reg_length = 56; // Maximum allowed number of coefficients in the coeff register
pc.printf(" User Defined FIR filter\n");
if ((ARRAY_SIZE(programmable_FIR) <= coeff_reg_length) && (count_of_active_coeffs <= coeff_reg_length)) {
pc.printf(" Aplying user-defined FIR filter coefficients from 'FIR_user_coeffs.h'\n");
ad77681_programmable_filter(device_adc, programmable_FIR, count_of_active_coeffs);
pc.printf(" Coeffs inserted successfully\n");
} else
pc.printf(" Incorrect count of coefficients in 'FIR_user_coeffs.h'\n");
}
/**
* AIN and REF buffers controll
*
*/
void static menu_4_adc_buffers_controll(void)
{
uint32_t new_AIN_buffer = 0, new_REF_buffer = 0, new_buffer = 0;
pc.printf(" Buffers settings: \n");
pc.printf(" 1 - Set AIN precharge buffers\n");
pc.printf(" 2 - Set REF buffers\n");
pc.printf(" Select an option: \n");
getUserInput(&new_buffer);
pc.putc('\n');
switch (new_buffer) {
case 1:
pc.printf(" Analog IN precharge buffers settings: \n");
pc.printf(" 1 - Turn ON both precharge buffers\n");
pc.printf(" 2 - Turn OFF both precharge buffers\n");
pc.printf(" 3 - Turn ON AIN- precharge buffer\n");
pc.printf(" 4 - Turn OFF AIN- precharge buffer\n");
pc.printf(" 5 - Turn ON AIN+ precharge buffer\n");
pc.printf(" 6 - Turn OFF AIN+ precharge buffer\n");
pc.printf(" Select an option: \n");
getUserInput(&new_AIN_buffer);
pc.putc('\n');
switch (new_AIN_buffer) {
case 1:
ad77681_set_AINn_buffer(device_adc, AD77681_AINn_ENABLED);
ad77681_set_AINp_buffer(device_adc, AD77681_AINp_ENABLED);
pc.printf(" AIN+ and AIN- enabled\n");
break;
case 2:
ad77681_set_AINn_buffer(device_adc, AD77681_AINn_DISABLED);
ad77681_set_AINp_buffer(device_adc, AD77681_AINp_DISABLED);
pc.printf(" AIN+ and AIN- disabled\n");
break;
case 3:
ad77681_set_AINn_buffer(device_adc, AD77681_AINn_ENABLED);
pc.printf(" AIN- Enabled\n");
break;
case 4:
ad77681_set_AINn_buffer(device_adc, AD77681_AINn_DISABLED);
pc.printf(" AIN- Disabled\n");
break;
case 5:
ad77681_set_AINp_buffer(device_adc, AD77681_AINp_ENABLED);
pc.printf(" AIN+ Enabled\n");
break;
case 6:
ad77681_set_AINp_buffer(device_adc, AD77681_AINp_DISABLED);
pc.printf(" AIN+ Disabled\n");
break;
default:
pc.printf(" Invalid option\n");
break;
}
break;
case 2:
pc.printf(" REF buffers settings: \n");
pc.printf(" 1 - Full REF- reference buffer\n");
pc.printf(" 2 - Full REF+ reference buffer\n");
pc.printf(" 3 - Unbuffered REF- reference buffer\n");
pc.printf(" 4 - Unbuffered REF+ reference buffer\n");
pc.printf(" 5 - Precharge REF- reference buffer\n");
pc.printf(" 6 - Precharge REF+ reference buffer\n");
pc.printf(" Select an option: \n");
getUserInput(&new_REF_buffer);
pc.putc('\n');
switch (new_REF_buffer) {
case 1:
ad77681_set_REFn_buffer(device_adc, AD77681_BUFn_FULL_BUFFER_ON);
pc.printf(" Fully buffered REF-\n");
break;
case 2:
ad77681_set_REFp_buffer(device_adc, AD77681_BUFp_FULL_BUFFER_ON);
pc.printf(" Fully buffered REF+\n");
break;
case 3:
ad77681_set_REFn_buffer(device_adc, AD77681_BUFn_DISABLED);
pc.printf(" Unbuffered REF-\n");
break;
case 4:
ad77681_set_REFp_buffer(device_adc, AD77681_BUFp_DISABLED);
pc.printf(" Unbuffered REF+\n");
break;
case 5:
ad77681_set_REFn_buffer(device_adc, AD77681_BUFn_ENABLED);
pc.printf(" Precharge buffer on REF-\n");
break;
case 6:
ad77681_set_REFp_buffer(device_adc, AD77681_BUFp_ENABLED);
pc.printf(" Precharge buffer on REF+\n");
break;
default:
pc.printf(" Invalid option\n");
break;
}
break;
default:
pc.printf(" Invalid option\n");
break;
}
print_prompt();
}
/**
* Default ADC Settings
*
*/
void static menu_5_set_default_settings(void)
{
int32_t default_settings_flag = ad77681_setup(&device_adc, init_params, ¤t_status);
if (default_settings_flag == SUCCESS)
pc.printf("\n Default ADC settings successfull\n");
else
pc.printf("\n Error in settings, please reset the ADC\n");
print_prompt();
}
/**
* VCM output controll
*
*/
void static menu_6_set_adc_vcm(void)
{
uint32_t new_vcm = 0;
pc.printf(" Avaliable VCM output voltage levels: \n");
pc.printf(" 1 - VCM = (AVDD1-AVSS)/2\n");
pc.printf(" 2 - VCM = 2.5V\n");
pc.printf(" 3 - VCM = 2.05V\n");
pc.printf(" 4 - VCM = 1.9V\n");
pc.printf(" 5 - VCM = 1.65V\n");
pc.printf(" 6 - VCM = 1.1V\n");
pc.printf(" 7 - VCM = 0.9V\n");
pc.printf(" 8 - VCM off\n");
pc.printf(" Select an option: \n");
getUserInput(&new_vcm);
pc.putc('\n');
switch (new_vcm) {
case 1:
ad77681_set_VCM_output(device_adc, AD77681_VCM_HALF_VCC);
pc.printf(" VCM set to half of the Vcc\n");
break;
case 2:
ad77681_set_VCM_output(device_adc, AD77681_VCM_2_5V);
pc.printf(" VCM set to 2.5V\n");
break;
case 3:
ad77681_set_VCM_output(device_adc, AD77681_VCM_2_05V);
pc.printf(" VCM set to 2.05V\n");
break;
case 4:
ad77681_set_VCM_output(device_adc, AD77681_VCM_1_9V);
pc.printf(" VCM set to 1.9V\n");
break;
case 5:
ad77681_set_VCM_output(device_adc, AD77681_VCM_1_65V);
pc.printf(" VCM set to 1.65V\n");
break;
case 6:
ad77681_set_VCM_output(device_adc, AD77681_VCM_1_1V);
pc.printf(" VCM set to 1.1V\n");
break;
case 7:
ad77681_set_VCM_output(device_adc, AD77681_VCM_0_9V);
pc.printf(" VCM set to 0.9V\n");
break;
case 8:
ad77681_set_VCM_output(device_adc, AD77681_VCM_OFF);
pc.printf(" VCM OFF\n");
break;
default:
pc.printf(" Invalid option\n");
break;
}
print_prompt();
}
/**
* Register read
*
*/
void static menu_7_adc_read_register(void)
{
uint32_t new_reg_to_read = 0;
uint8_t reg_read_buf[3], read_adc_data[6], hex_number = 0;
uint8_t HI = 0, MID = 0, LO = 0;
char binary_number[8], other_register[2] = "";
double voltage;
pc.printf(" Read desired register: \n");
pc.printf(" 1 - 0x03 - Chip type\n");
pc.printf(" 2 - 0x14 - Interface format\n");
pc.printf(" 3 - 0x15 - Power clock\n");
pc.printf(" 4 - 0x16 - Analog\n");
pc.printf(" 5 - 0x17 - Analog2\n");
pc.printf(" 6 - 0x18 - Conversion\n");
pc.printf(" 7 - 0x19 - Digital filter\n");
pc.printf(" 8 - 0x1A - SINC3 Dec. rate MSB\n");
pc.printf(" 9 - 0x1B - SINC3 Dec. rate LSB\n");
pc.printf(" 10 - 0x1C - Duty cycle ratio\n");
pc.printf(" 11 - 0x1D - Sync, Reset\n");
pc.printf(" 12 - 0x1E - GPIO Controll\n");
pc.printf(" 13 - 0x1F - GPIO Write\n");
pc.printf(" 14 - 0x20 - GPIO Read\n");
pc.printf(" 15 - 0x21 - 0x23 - Offset register\n");
pc.printf(" 16 - 0x24 - 0x26 - Gain register\n");
pc.printf(" 17 - 0x2C - ADC Data\n");
pc.printf(" Select an option: \n");
getUserInput(&new_reg_to_read);
pc.putc('\n');
switch (new_reg_to_read) {
case 1:
ad77681_spi_reg_read(device_adc, AD77681_REG_CHIP_TYPE, reg_read_buf);
print_binary(reg_read_buf[1], binary_number);
pc.printf(" Value of 0x03 - Chip type register is: 0x%x 0b%s\n", reg_read_buf[1], binary_number);
break;
case 2:
ad77681_spi_reg_read(device_adc, AD77681_REG_INTERFACE_FORMAT, reg_read_buf);
print_binary(reg_read_buf[1], binary_number);
pc.printf(" Value of 0x14 - Interface format register is: 0x%x 0b%s\n", reg_read_buf[1], binary_number);
break;
case 3:
ad77681_spi_reg_read(device_adc, AD77681_REG_POWER_CLOCK, reg_read_buf);
print_binary(reg_read_buf[1], binary_number);
pc.printf(" Value of 0x15 - Power clock register is: 0x%x 0b%s\n", reg_read_buf[1], binary_number);
break;
case 4:
ad77681_spi_reg_read(device_adc, AD77681_REG_ANALOG, reg_read_buf);
print_binary(reg_read_buf[1], binary_number);
pc.printf(" Value of 0x16 - Anlaog register is: 0x%x 0b%s\n", reg_read_buf[1], binary_number);
break;
case 5:
ad77681_spi_reg_read(device_adc, AD77681_REG_ANALOG2, reg_read_buf);
print_binary(reg_read_buf[1], binary_number);
pc.printf(" Value of 0x17 - Analog2 regster is: 0x%x 0b%s\n", reg_read_buf[1], binary_number);
break;
case 6:
ad77681_spi_reg_read(device_adc, AD77681_REG_CONVERSION, reg_read_buf);
print_binary(reg_read_buf[1], binary_number);
pc.printf(" Value of 0x18 - Conversion register is: 0x%x 0b%s\n", reg_read_buf[1], binary_number);
break;
case 7:
ad77681_spi_reg_read(device_adc, AD77681_REG_DIGITAL_FILTER, reg_read_buf);
print_binary(reg_read_buf[1], binary_number);
pc.printf(" Value of 0x19 - Digital filter register is: 0x%x 0b%s\n", reg_read_buf[1], binary_number);
break;
case 8:
ad77681_spi_reg_read(device_adc, AD77681_REG_SINC3_DEC_RATE_MSB, reg_read_buf);
print_binary(reg_read_buf[1], binary_number);
pc.printf(" Value of 0x1A - SINC3 Dec. rate MSB is: 0x%x 0b%s\n", reg_read_buf[1], binary_number);
break;
case 9:
ad77681_spi_reg_read(device_adc, AD77681_REG_SINC3_DEC_RATE_LSB, reg_read_buf);
print_binary(reg_read_buf[1], binary_number);
pc.printf(" Value of 0x1B - SINC3 Dec. rate LSB is: 0x%x 0b%s\n", reg_read_buf[1], binary_number);
break;
case 10:
ad77681_spi_reg_read(device_adc, AD77681_REG_DUTY_CYCLE_RATIO, reg_read_buf);
print_binary(reg_read_buf[1], binary_number);
pc.printf(" Value of 0x1C - Duty cycle ratio 0x%x 0b%s\n", reg_read_buf[1], binary_number);
break;
case 11:
ad77681_spi_reg_read(device_adc, AD77681_REG_SYNC_RESET, reg_read_buf);
print_binary(reg_read_buf[1], binary_number);
pc.printf(" Value of 0x1D - Sync, Reset 0x%x 0b%s\n", reg_read_buf[1], binary_number);
break;
case 12:
ad77681_spi_reg_read(device_adc, AD77681_REG_GPIO_CONTROL, reg_read_buf);
print_binary(reg_read_buf[1], binary_number);
pc.printf(" Value of 0x1E - GPIO Controll is: 0x%x 0b%s\n", reg_read_buf[1], binary_number);
break;
case 13:
ad77681_spi_reg_read(device_adc, AD77681_REG_GPIO_WRITE, reg_read_buf);
print_binary(reg_read_buf[1], binary_number);
pc.printf(" Value of 0x1F - GPIO Write is: 0x%x 0b%s\n", reg_read_buf[1], binary_number);
break;
case 14:
ad77681_spi_reg_read(device_adc, AD77681_REG_GPIO_READ, reg_read_buf);
print_binary(reg_read_buf[1], binary_number);
pc.printf(" Value of 0x20 - GPIO Read is: 0x%x 0b%s\n", reg_read_buf[1], binary_number);
break;
case 15:
ad77681_spi_reg_read(device_adc, AD77681_REG_OFFSET_HI, reg_read_buf);
HI = reg_read_buf[1];
ad77681_spi_reg_read(device_adc, AD77681_REG_OFFSET_MID, reg_read_buf);
MID = reg_read_buf[1];
ad77681_spi_reg_read(device_adc, AD77681_REG_OFFSET_LO, reg_read_buf);
LO = reg_read_buf[1];
pc.printf(" Value of 0x21 - 0x23 - Offset register is: 0x%x %x %x\n", HI, MID, LO);
break;
case 16:
ad77681_spi_reg_read(device_adc, AD77681_REG_GAIN_HI, reg_read_buf);
HI = reg_read_buf[1];
ad77681_spi_reg_read(device_adc, AD77681_REG_GAIN_MID, reg_read_buf);
MID = reg_read_buf[1];
ad77681_spi_reg_read(device_adc, AD77681_REG_GAIN_LO, reg_read_buf);
LO = reg_read_buf[1];
pc.printf(" Value of 0x24 - 0x26 - Gain register is: 0x%x %x %x\n", HI, MID, LO);
break;
case 17:
ad77681_spi_read_adc_data(device_adc, read_adc_data, AD77681_REGISTER_DATA_READ);
pc.printf(" Value of 0x2C - ADC data is: 0x%x 0x%x 0x%x\n", read_adc_data[1], read_adc_data[2], read_adc_data[3]);
break;
default :
pc.printf(" Invalid option\n");
break;
}
print_prompt();
}
/**
* Read ADC data
*
*/
void static menu_8_adc_cont_read_data(void)
{
uint32_t new_sample_count = 0;
int32_t ret;
pc.printf(" Read Continuous ADC Data");
pc.printf(" Input number of samples (1 to 4096): \n");
ret = getUserInput(&new_sample_count); // Get user input
if ((new_sample_count <= 4096) && (ret == SUCCESS) ) {
pc.printf("\n%d of samples\n", new_sample_count); // Print Desired Measurement Count
measured_data.samples = (uint16_t)(new_sample_count);
measured_data.finish = false;
measured_data.count = 0;
pc.printf("Sampling....\n");
cont_sampling();
pc.printf("Done Sampling....\n");
} else {
pc.printf(" Invalid option\n");
}
print_prompt();
}
/**
* ADC Continuous read
*
*/
void static cont_sampling()
{
uint8_t buf[6];
ad77681_set_continuos_read(device_adc, AD77681_CONTINUOUS_READ_ENABLE);
__enable_irq(); // Enable all interupts
drdy.enable_irq(); // Enable interrupt on DRDY pin
drdy.fall(&drdy_interrupt); // Interrupt on falling edne of DRDY
while (!measured_data.finish) { // While loop. Waiting for the measurements to be completed
if (int_event==true) { // Checks if Interrupt Occurred
ad77681_spi_read_adc_data(device_adc, buf, AD77681_CONTINUOUS_DATA_READ); // Read the continuous read data
if (device_adc->conv_len == AD77681_CONV_24BIT) // 24bit format
measured_data.raw_data[measured_data.count] = (buf[0] << 16 | buf[1] << 8 | buf[2]<< 0); // Combining the SPI buffers
else // 16bit format
measured_data.raw_data[measured_data.count] = (buf[0] << 8 | buf[1]<< 0); // Combining the SPI buffers
measured_data.count++; // Increment Measured Data Counter
int_event=false; // Set int event flag after reading the Data
}
}
ad77681_set_continuos_read(device_adc, AD77681_CONTINUOUS_READ_DISABLE); // Disable continuous ADC read
}
/**
* Reset ADC
*
*/
void static menu_9_reset_ADC(void)
{
uint32_t new_reset_option = 0;
pc.printf(" ADC reset opportunities: \n");
pc.printf(" 1 - Soft reset - over SPI\n");
pc.printf(" 2 - Hard reset - uing RESET pin\n");
pc.printf(" Select an option: \n");
getUserInput(&new_reset_option);
pc.putc('\n');
switch (new_reset_option) {
case 1:
ad77681_soft_reset(device_adc); // Perform soft reset thru SPI write
pc.printf(" ADC after soft reset\n");
break;
case 2:
adc_hard_reset();
pc.printf(" ADC after hard reset\n");
break;
default:
pc.printf(" Invalid option\n");
break;
}
print_prompt();
}
/**
* Reset ADC thru SDP-K1 GPIO
*
*
*/
void static adc_hard_reset()
{
adc_reset = 0; // Set ADC reset pin to Low
mdelay(100); // Delay 100ms
adc_reset = 1; // Set ADC reset pin to High
mdelay(100); // Delay 100ms
}
/**
* Sleep mode / Wake up ADC
*
*/
void static menu_10_power_down(void)
{
uint32_t new_sleep = 0;
pc.printf(" Controll sleep mode of the ADC: \n");
pc.printf(" 1 - Put ADC to sleep mode\n");
pc.printf(" 2 - Wake up ADC\n");
pc.printf(" Select an option: \n");
getUserInput(&new_sleep);
pc.putc('\n');
switch (new_sleep) {
case 1:
ad77681_power_down(device_adc, AD77681_SLEEP);
pc.printf(" ADC put to sleep mode\n");
break;
case 2:
ad77681_power_down(device_adc, AD77681_WAKE);
pc.printf(" ADC powered\n");
break;
default:
pc.printf("Invalid option\n");
break;
}
print_prompt();
}
/**
* ADC's GPIO Controll
*
*/
void static menu_11_ADC_GPIO(void)
{
uint8_t GPIO_state;
uint32_t new_gpio_sel = 0;
char binary_number[8];
int32_t ret_val = FAILURE, ret;
pc.printf(" ADC GPIO Controll: \n");
pc.printf(" 1 - Read from GPIO\n");
pc.printf(" 2 - Write to GPIO\n");
pc.printf(" 3 - Set GPIO as input / output\n");
pc.printf(" 4 - Change GPIO settings\n");
pc.printf(" Select an option: \n");
getUserInput(&new_gpio_sel);
pc.putc('\n');
switch (new_gpio_sel) {
case 1:
ad77681_gpio_read(device_adc, &GPIO_state, AD77681_ALL_GPIOS);
print_binary(GPIO_state, binary_number);
pc.printf(" Current GPIO Values:\n GPIO0: %c\n GPIO1: %c\n GPIO2: %c\n GPIO3: %c\n", binary_number[7], binary_number[6], binary_number[5], binary_number[4]);
break;
case 2:
adc_GPIO_write();
break;
case 3:
adc_GPIO_inout();
break;
case 4:
adc_GPIO_settings();
break;
default:
pc.printf(" Invalid option\n");
break;
}
print_prompt();
}
/**
* Write to GPIOs, part of the ADC_GPIO function
*
*/
void static adc_GPIO_write(void)
{
uint32_t new_gpio_write = 0, new_value = 0;
int32_t ret, ret_val;
pc.printf(" Write to GPIO: \n");
pc.printf(" 1 - Write to all GPIOs\n");
pc.printf(" 2 - Write to GPIO0\n");
pc.printf(" 3 - Write to GPIO1\n");
pc.printf(" 4 - Write to GPIO2\n");
pc.printf(" 5 - Write to GPIO3\n");
pc.printf(" Select an option: \n");
getUserInput(&new_gpio_write);
pc.putc('\n');
switch (new_gpio_write)
{
case 1:
pc.printf("Insert value to be writen into all GPIOs, same value for all GPIOs: ");
ret = getUserInput(&new_value);
if (((new_value == GPIO_HIGH) || (new_value == GPIO_LOW)) && (ret == SUCCESS)) {
new_value *= 0xF;
ret_val = ad77681_gpio_write(device_adc, new_value, AD77681_ALL_GPIOS);
pc.printf("\n Value %d successully written to all GPOIs\n", new_value);
} else
pc.printf("\nInvalid value\n");
break;
case 2:
pc.printf("Insert value to be written into GPIO0: ");
ret = getUserInput(&new_value);
if (((new_value == GPIO_HIGH) || (new_value == GPIO_LOW)) && (ret == SUCCESS)) {
ret_val = ad77681_gpio_write(device_adc, new_value, AD77681_GPIO0);
pc.printf("\n Value %d successully written to GPIO0\n", new_value);
} else
pc.printf("\nInvalid value\n");
break;
case 3:
pc.printf("Insert value to be written into GPIO1: ");
ret = getUserInput(&new_value);
if (((new_value == GPIO_HIGH) || (new_value == GPIO_LOW)) && (ret == SUCCESS)) {
ret_val = ad77681_gpio_write(device_adc, new_value, AD77681_GPIO1);
pc.printf("\n Value %d successully written to GPIO1\n", new_value);
} else
pc.printf("\nInvalid value\n");
break;
case 4:
pc.printf("Insert value to be written into GPIO2: ");
ret = getUserInput(&new_value);
if (((new_value == GPIO_HIGH) || (new_value == GPIO_LOW)) && (ret == SUCCESS)) {
ret_val = ad77681_gpio_write(device_adc, new_value, AD77681_GPIO2);
pc.printf("\n Value %d successully written to GPIO2\n", new_value);
} else
pc.printf("\nInvalid value\n");
break;
case 5:
pc.printf("Insert value to be written into GPIO3: ");
ret = getUserInput(&new_value);
if (((new_value == GPIO_HIGH) || (new_value == GPIO_LOW)) && (ret == SUCCESS)) {
ret_val = ad77681_gpio_write(device_adc, new_value, AD77681_GPIO3);
pc.printf("\n Value %d successully written to GPIO3\n", new_value);
} else
pc.printf("\nInvalid value\n");
break;
default:
pc.printf(" Invalid option\n");
break;
}
}
/**
* GPIO direction, part of the ADC_GPIO function
*
*/
void static adc_GPIO_inout(void)
{
uint32_t new_gpio_inout = 0, new_gpio_inout_set = 0;
int32_t ret_val;
pc.printf(" Set GPIOs as input or output: \n");
pc.printf(" 1 - Set all GPIOs\n");
pc.printf(" 2 - Set GPIO0\n");
pc.printf(" 3 - Set GPIO1\n");
pc.printf(" 4 - Set GIPO2\n");
pc.printf(" 5 - Set GPIO3\n");
pc.printf(" Select an option: \n");
getUserInput(&new_gpio_inout);
pc.putc('\n');
switch (new_gpio_inout) {
case 1:
pc.printf(" 1 - Set all GPIOS as inputs\n");
pc.printf(" 2 - Set all GPIOS as outputs\n");
getUserInput(&new_gpio_inout_set);
pc.putc('\n');
if ((new_gpio_inout_set == 1) || (new_gpio_inout_set == 2)) {
new_gpio_inout_set -= 1;
new_gpio_inout_set *= 0xF;
ret_val = ad77681_gpio_inout(device_adc, new_gpio_inout_set, AD77681_ALL_GPIOS);
pc.printf("All GPIOs successfully set");
} else
pc.printf("\nInvalid value\n");
break;
case 2:
pc.printf(" 1 - Set GPIO0 as input\n");
pc.printf(" 2 - Set GPIO0 as output\n");
getUserInput(&new_gpio_inout_set);
pc.putc('\n');
if ((new_gpio_inout_set == 1) || (new_gpio_inout_set == 2)) {
new_gpio_inout_set -= 1;
ret_val = ad77681_gpio_inout(device_adc, new_gpio_inout_set, AD77681_GPIO0);
pc.printf("GPIO0 successfully set");
} else
pc.printf("\nInvalid value\n");
break;
case 3:
pc.printf(" 1 - Set GPIO1 as input\n");
pc.printf(" 2 - Set GPIO1 as output\n");
getUserInput(&new_gpio_inout_set);
pc.putc('\n');
if ((new_gpio_inout_set == 1) || (new_gpio_inout_set == 2)) {
new_gpio_inout_set -= 1;
ret_val = ad77681_gpio_inout(device_adc, new_gpio_inout_set, AD77681_GPIO1);
pc.printf("GPIO1 successfully set");
} else
pc.printf("\nInvalid value\n");
break;
case 4:
pc.printf(" 1 - Set GPIO2 as input\n");
pc.printf(" 2 - Set GPIO2 as output\n");
getUserInput(&new_gpio_inout_set);
pc.putc('\n');
if ((new_gpio_inout_set == 1) || (new_gpio_inout_set == 2)) {
new_gpio_inout_set -= 1;
ret_val = ad77681_gpio_inout(device_adc, new_gpio_inout_set, AD77681_GPIO2);
pc.printf("GPIO2 successfully set");
} else
pc.printf("\nInvalid value\n");
break;
case 5:
pc.printf(" 1 - Set GPIO3 as input\n");
pc.printf(" 2 - Set GPIO3 as output\n");
getUserInput(&new_gpio_inout_set);
pc.putc('\n');
if ((new_gpio_inout_set == 1) || (new_gpio_inout_set == 2)) {
new_gpio_inout_set -= 1;
ret_val = ad77681_gpio_inout(device_adc, new_gpio_inout_set, AD77681_GPIO3);
pc.printf("GPIO3 successfully set");
} else
pc.printf("\nInvalid value\n");
break;
default:
pc.printf(" Invalid option\n");
break;
}
}
/**
* Additional GPIO settings, part of the ADC_GPIO function
*
*/
void static adc_GPIO_settings(void)
{
uint32_t new_gpio_settings = 0;
pc.printf(" GPIO Settings: \n");
pc.printf(" 1 - Enable all GPIOs (Global enble)\n");
pc.printf(" 2 - Disable all GPIOs (Global disable)\n");
pc.printf(" 3 - Set GPIO0 - GPIO2 as open drain\n");
pc.printf(" 4 - Set GPIO0 - GPIO2 as strong driver\n");
pc.printf(" Select an option: \n");
getUserInput(&new_gpio_settings);
pc.putc('\n');
switch (new_gpio_settings) {
case 1:
ad77681_global_gpio(device_adc, AD77681_GLOBAL_GPIO_ENABLE);
pc.printf(" Global GPIO enalbe bit enabled");
break;
case 2:
ad77681_global_gpio(device_adc, AD77681_GLOBAL_GPIO_DISABLE);
pc.printf(" Global GPIO enalbe bit disabled");
break;
default:
pc.printf(" Invalid option\n");
break;
}
}
/**
* Read ADC status from status registers
*
*/
void static menu_12_read_master_status(void)
{
uint8_t reg_read_buf[3];
char binary_number[8];
char ok[3] = { 'O', 'K' }, fault[6] = { 'F', 'A', 'U', 'L', 'T' };
ad77681_status(device_adc, current_status);
pc.putc('\n');
pc.printf("== MASTER STATUS REGISER\n");
pc.printf("Master error: %s\n", ((current_status->master_error == 0) ? (ok) : (fault)));
pc.printf("ADC error: %s\n", ((current_status->adc_error == 0) ? (ok) : (fault)));
pc.printf("Dig error: %s\n", ((current_status->dig_error == 0) ? (ok) : (fault)));
pc.printf("Ext. clock: %s\n", ((current_status->adc_err_ext_clk_qual == 0) ? (ok) : (fault)));
pc.printf("Filter saturated: %s\n", ((current_status->adc_filt_saturated == 0) ? (ok) : (fault)));
pc.printf("Filter not settled: %s\n", ((current_status->adc_filt_not_settled == 0) ? (ok) : (fault)));
pc.printf("SPI error: %s\n", ((current_status->spi_error == 0) ? (ok) : (fault)));
pc.printf("POR Flag: %s\n", ((current_status->por_flag == 0) ? (ok) : (fault)));
if (current_status->spi_error == 1) {
pc.printf("\n== SPI DIAG STATUS REGISER\n");
pc.printf("SPI ignore error: %s\n", ((current_status->spi_ignore == 0) ? (ok) : (fault)));
pc.printf("SPI clock count error: %s\n", ((current_status->spi_clock_count == 0) ? (ok) : (fault)));
pc.printf("SPI read error: %s\n", ((current_status->spi_read_error == 0) ? (ok) : (fault)));
pc.printf("SPI write error: %s\n", ((current_status->spi_write_error == 0) ? (ok) : (fault)));
pc.printf("SPI CRC error: %s\n", ((current_status->spi_crc_error == 0) ? (ok) : (fault)));
}
if (current_status->adc_error == 1) {
pc.printf("\n== ADC DIAG STATUS REGISER\n");
pc.printf("DLDO PSM error: %s\n", ((current_status->dldo_psm_error == 0) ? (ok) : (fault)));
pc.printf("ALDO PSM error: %s\n", ((current_status->aldo_psm_error == 0) ? (ok) : (fault)));
pc.printf("REF DET error: %s\n", ((current_status->ref_det_error == 0) ? (ok) : (fault)));
pc.printf("FILT SAT error: %s\n", ((current_status->filt_sat_error == 0) ? (ok) : (fault)));
pc.printf("FILT NOT SET error: %s\n", ((current_status->filt_not_set_error == 0) ? (ok) : (fault)));
pc.printf("EXT CLK QUAL error: %s\n", ((current_status->ext_clk_qual_error == 0) ? (ok) : (fault)));
}
if (current_status->dig_error == 1) {
pc.printf("\n== DIGITAL DIAG STATUS REGISER\n");
pc.printf("Memory map CRC error: %s\n", ((current_status->memoy_map_crc_error == 0) ? (ok) : (fault)));
pc.printf("RAM CRC error: %s\n", ((current_status->ram_crc_error == 0) ? (ok) : (fault)));
pc.printf("FUSE CRC error: %s\n", ((current_status->fuse_crc_error == 0) ? (ok) : (fault)));
}
pc.putc('\n');
print_prompt();
}
/**
* Set Vref anc MCLK as "exteranl" values, depending on you setup
*
*/
void static menu_13_mclk_vref(void)
{
uint32_t input = 0, new_settings = 0;
int32_t ret;
pc.printf(" Set Vref and Mclk: \n");
pc.printf(" 1 - Change Vref\n");
pc.printf(" 2 - Change MCLK\n");
pc.printf(" Select an option: \n");
getUserInput(&new_settings);
pc.putc('\n');
switch (new_settings) {
case 1:
pc.printf(" Change Vref from %d mV to [mV]: ", device_adc->vref); // Vref change
ret = getUserInput(&input);
if ((input >= 1000) && (input <= 5000) && (ret == SUCCESS)) {
pc.printf("\n New Vref value is %d mV", input);
device_adc->vref = input;
#ifdef CN0540_ADI_FFT_H_
// Update the Vref, Mclk and sampling rate
update_FFT_enviroment(device_adc->vref, device_adc->mclk, device_adc->sample_rate, FFT_data);
#endif //CN0540_ADI_FFT_H_
} else
pc.printf(" Invalid option\n");
pc.putc('\n');
break;
case 2:
pc.printf(" Change MCLK from %d kHz to [kHz]: ", device_adc->mclk); // MCLK change
ret = getUserInput(&input);
if ((input >= 10000) && (input <= 50000) && (ret == SUCCESS)){
pc.printf("\n New MCLK value is %d kHz\n", input);
device_adc->vref = input;
ad77681_update_sample_rate(device_adc); // Update the sample rate after changinig the MCLK
#ifdef CN0540_ADI_FFT_H_
// Update the Vref, Mclk and sampling rate
update_FFT_enviroment(device_adc->vref, device_adc->mclk, device_adc->sample_rate, FFT_data);
#endif //CN0540_ADI_FFT_H_
} else
pc.printf(" Invalid option\n");
pc.putc('\n');
break;
default:
pc.printf(" Invalid option\n");
break;
}
print_prompt();
}
/**
* Print measured data and transfered to voltage
*
*/
void static menu_14_print_measured_data(void)
{
double voltage;
int32_t shifted_data;
uint16_t i;
char buf[15];
if (measured_data.finish) {
// Printing Voltage
pc.printf("\n\nVoltage\n");
for ( i = 0; i < measured_data.samples; i++) {
ad77681_data_to_voltage(device_adc, &measured_data.raw_data[i], &voltage);
pc.printf("%.9f \n",voltage);
}
// Printing Codes
pc.printf("\n\nCodes\n");
for(i = 0 ; i < measured_data.samples ; i++) {
if (measured_data.raw_data[i] & 0x800000)
shifted_data = (int32_t)((0xFF << 24) | measured_data.raw_data[i]);
else
shifted_data = (int32_t)((0x00 << 24) | measured_data.raw_data[i]);
pc.printf("%d\n", shifted_data + AD7768_HALF_SCALE);
}
// Printing Raw Date
pc.printf("\n\nRaw data\n");
for (i = 0; i < measured_data.samples; i++)
pc.printf("%d\n", measured_data.raw_data[i]);
// Set measured_data.finish to false after Printing
measured_data.finish = false;
} else
pc.printf("Data not prepared\n");
print_prompt();
}
/**
* Set data output mode
*
*/
void static menu_15_set_adc_data_output_mode(void)
{
uint32_t new_data_mode = 0, new_length = 0, new_status = 0, new_crc = 0, ret;
pc.printf(" ADC data outpup modes: \n");
pc.printf(" 1 - Continuous: waiting for DRDY\n");
pc.printf(" 2 - Continuous one shot: waiting for SYNC_IN\n");
pc.printf(" 3 - Single-conversion standby\n");
pc.printf(" 4 - Periodic standby\n");
pc.printf(" 5 - Standby mode\n");
pc.printf(" 6 - 16bit or 24bit data format\n");
pc.printf(" 7 - Status bit output\n");
pc.printf(" 8 - Switch form diag mode to measure\n");
pc.printf(" 9 - Switch form measure to diag mode\n");
pc.printf(" 10 - Set CRC type\n");
pc.printf(" Select an option: \n");
getUserInput(&new_data_mode);
pc.putc('\n');
switch (new_data_mode) {
case 1:
ad77681_set_conv_mode(device_adc, AD77681_CONV_CONTINUOUS, device_adc->diag_mux_sel, device_adc->conv_diag_sel);// DIAG MUX NOT SELECTED
pc.printf(" Continuous mode set\n");
break;
case 2:
ad77681_set_conv_mode(device_adc, AD77681_CONV_ONE_SHOT, device_adc->diag_mux_sel, device_adc->conv_diag_sel);
pc.printf(" Continuous one shot conversion set\n");
break;
case 3:
ad77681_set_conv_mode(device_adc, AD77681_CONV_SINGLE, device_adc->diag_mux_sel, device_adc->conv_diag_sel);
pc.printf(" Single conversion standby mode set\n");
break;
case 4:
ad77681_set_conv_mode(device_adc, AD77681_CONV_PERIODIC, device_adc->diag_mux_sel, device_adc->conv_diag_sel);
pc.printf(" Periodiec standby mode set\n");
break;
case 5:
ad77681_set_conv_mode(device_adc, AD77681_CONV_STANDBY, device_adc->diag_mux_sel, device_adc->conv_diag_sel);
pc.printf(" Standby mode set\n");
break;
case 6:
pc.printf(" Conversion length select: \n");
pc.printf(" 1 - 24bit length\n");
pc.printf(" 2 - 16bit length\n");
getUserInput(&new_length);
pc.putc('\n');
switch (new_length) {
case 1:
ad77681_set_convlen(device_adc, AD77681_CONV_24BIT);
pc.printf(" 24bit data output format selected\n");
break;
case 2:
ad77681_set_convlen(device_adc, AD77681_CONV_16BIT);
pc.printf(" 16bit data output format selected\n");
break;
default:
pc.printf(" Invalid option\n");
break;
}
break;
case 7:
pc.printf(" Status bit output: \n");
pc.printf(" 1 - Enable status bit after each ADC conversion\n");
pc.printf(" 2 - Disable status bit after each ADC conversion\n");
getUserInput(&new_status);
pc.putc('\n');
switch (new_status) {
case 1:
ad77681_set_status_bit(device_adc, true);
pc.printf(" Status bit enabled\n");
break;
case 2:
ad77681_set_status_bit(device_adc, false);
pc.printf(" Status bit disabled\n");
break;
default:
pc.printf(" Invalid option\n");
break;
}
break;
case 8:
ad77681_set_conv_mode(device_adc, device_adc->conv_mode, device_adc->diag_mux_sel, false);// DIAG MUX NOT SELECTED
pc.printf(" Measure mode selected\n");
break;
case 9:
ad77681_set_conv_mode(device_adc, device_adc->conv_mode, device_adc->diag_mux_sel, true); // DIAG MUX SELECTED
pc.printf(" Diagnostic mode selected\n");
break;
case 10:
pc.printf(" CRC settings \n");
pc.printf(" 1 - Disable CRC\n");
pc.printf(" 2 - 8-bit polynomial CRC\n");
pc.printf(" 3 - XOR based CRC\n");
getUserInput(&new_crc);
pc.putc('\n');
switch (new_crc) {
case 1:
ad77681_set_crc_sel(device_adc, AD77681_NO_CRC);
pc.printf(" CRC disabled\n");
break;
case 2:
ad77681_set_crc_sel(device_adc, AD77681_CRC);
pc.printf(" 8-bit polynomial CRC method selected\n");
break;
case 3:
ad77681_set_crc_sel(device_adc, AD77681_XOR);
pc.printf(" XOR based CRC method selected\n");
break;
default:
pc.printf(" Invalid option\n");
break;
}
break;
default:
pc.printf(" Invalid option\n");
break;
}
print_prompt();
}
/**
* Set diagnostic mode
*
*/
void static menu_16_set_adc_diagnostic_mode(void)
{
uint32_t new_diag_mode = 0;
pc.printf(" ADC diagnostic modes: \n");
pc.printf(" 1 - Internal temperature sensor\n");
pc.printf(" 2 - AIN shorted\n");
pc.printf(" 3 - Positive full-scale\n");
pc.printf(" 4 - Negative full-scale\n");
pc.printf(" Select an option: \n");
getUserInput(&new_diag_mode);
pc.putc('\n');
switch (new_diag_mode) {
case 1:
ad77681_set_conv_mode(device_adc, device_adc->conv_mode, AD77681_TEMP_SENSOR, true);
pc.printf(" Diagnostic mode: Internal temperature sensor selected\n");
break;
case 2:
ad77681_set_conv_mode(device_adc, device_adc->conv_mode, AD77681_AIN_SHORT, true);
pc.printf(" Diagnostic mode: AIN shorted selected\n");
break;
case 3:
ad77681_set_conv_mode(device_adc, device_adc->conv_mode, AD77681_POSITIVE_FS, true);
pc.printf(" Diagnostic mode: Positive full-scale selected\n");
break;
case 4:
ad77681_set_conv_mode(device_adc, device_adc->conv_mode, AD77681_NEGATIVE_FS, true);
pc.printf(" Diagnostic mode: Negative full-scale selected\n");
break;
default:
pc.printf(" Invalid option\n");
break;
}
print_prompt();
}
/**
* Do the FFT
*
*/
void static menu_17_do_the_fft(void)
{
pc.printf(" FFT in progress...\n");
measured_data.samples = FFT_data->fft_length * 2;
measured_data.samples = 4096;
measured_data.finish = false;
measured_data.count = 0;
pc.printf("Sampling....\n");
cont_sampling();
perform_FFT(measured_data.raw_data, FFT_data, FFT_meas, device_adc->sample_rate);
pc.printf(" FFT Done!\n");
measured_data.finish = false;
pc.printf("\n THD:\t\t%.3f dB", FFT_meas->THD);
pc.printf("\n SNR:\t\t%.3f dB", FFT_meas->SNR);
pc.printf("\n DR:\t\t%.3f dB", FFT_meas->DR);
pc.printf("\n Fundamental:\t%.3f dBFS", FFT_meas->harmonics_mag_dbfs[0]);
pc.printf("\n Fundamental:\t%.3f Hz", FFT_meas->harmonics_freq[0]*FFT_data->bin_width);
pc.printf("\n RMS noise:\t%.6f uV", FFT_meas->RMS_noise * 1000000.0);
pc.printf("\n LSB noise:\t%.3f", FFT_meas->transition_noise_LSB);
print_prompt();
}
/**
* Setting of the FFT module
*
*/
void static menu_18_fft_settings(void)
{
uint32_t new_menu_select, new_window, new_sample_count;
pc.printf(" FFT settings: \n");
pc.printf(" 1 - Set window type\n");
pc.printf(" 2 - Set sample count\n");
pc.printf(" 3 - Print FFT plot\n");
pc.printf(" Select an option: \n\n");
getUserInput(&new_menu_select);
switch (new_menu_select) {
case 1:
pc.printf(" Choose window type:\n");
pc.printf(" 1 - 7-term Blackman-Harris\n");
pc.printf(" 2 - Rectangular\n");
getUserInput(&new_window);
switch (new_window) {
case 1:
pc.printf(" 7-7-term Blackman-Harris window selected\n");
FFT_data->window = BLACKMAN_HARRIS_7TERM;
break;
case 2:
pc.printf(" Rectalngular window selected\n");
FFT_data->window = RECTANGULAR;
break;
default:
pc.printf(" Invalid option\n");
break;
}
break;
case 2:
pc.printf(" Set sample count:\n");
pc.printf(" 1 - 4096 samples\n");
pc.printf(" 2 - 1024 samples\n");
pc.printf(" 3 - 256 samples\n");
pc.printf(" 4 - 64 samples\n");
pc.printf(" 5 - 16 samples\n");
getUserInput(&new_sample_count);
switch (new_sample_count) {
case 1:
pc.printf(" 4096 samples selected\n");
FFT_init(4096, FFT_data); // Update the FFT module with a new sample count
break;
case 2:
pc.printf(" 1024 samples selected\n");
FFT_init(1024, FFT_data);
break;
case 3:
pc.printf(" 256 samples selected\n");
FFT_init(256, FFT_data);
break;
case 4:
pc.printf(" 64 samples selected\n");
FFT_init(64, FFT_data);
break;
case 5:
pc.printf(" 16 samples selected\n");
FFT_init(16, FFT_data);
break;
default:
pc.printf(" Invalid option\n");
break;
}
break;
case 3:
if (FFT_data->fft_done == true) {
pc.printf(" Printing FFT plot in dB:\n");
for (uint16_t i = 0; i < FFT_data->fft_length; i++)
pc.printf("%.4f\n", FFT_data->fft_dB[i]);
}
else
pc.printf(" Data not prepared\n");
break;
default:
pc.printf(" Invalid option\n");
break;
}
print_prompt();
}
/**
* Set Gains and Offsets
*
*/
void static menu_19_gains_offsets(void)
{
uint32_t gain_offset, new_menu_select;
int32_t ret;
pc.printf(" Gains and Offsets settings: \n");
pc.printf(" 1 - Set gain\n");
pc.printf(" 2 - Set offset\n");
pc.printf(" Select an option: \n");
getUserInput(&new_menu_select);
switch (new_menu_select) {
case 1:
pc.printf(" Insert new Gain value in decimal form\n");
ret = getUserInput(&gain_offset);
if ((gain_offset <= 0xFFFFFF) && (ret == SUCCESS)) {
ad77681_apply_gain(device_adc, gain_offset);
pc.printf(" Value %d has been successfully inserted to the Gain register\n", gain_offset);
} else
pc.printf(" Invalid value\n");
break;
case 2:
pc.printf(" Insert new Offset value in decimal form\n");
ret = getUserInput(&gain_offset);
if ((gain_offset <= 0xFFFFFF) && (ret == SUCCESS)) {
ad77681_apply_offset(device_adc, gain_offset);
pc.printf(" Value %d has been successfully inserted to the Offset register\n", gain_offset);
} else
pc.printf(" Invalid value\n");
break;
default:
pc.printf(" Invalid option\n");
break;
}
print_prompt();
}
/**
* Chceck read and write functionaity by writing to and reading from scratchpad register
*
*/
void static menu_20_check_scratchpad(void)
{
int32_t ret;
uint32_t ret_val;
uint32_t new_menu_select;
uint8_t chceck_sequence;
pc.printf(" Scratchpad check\n");
pc.printf(" Insert 8bit number for scratchpad check: \n");
ret = getUserInput(&new_menu_select);
if ((new_menu_select <= 0xFF) && (new_menu_select >= 0) && (ret == SUCCESS)) {
chceck_sequence = (uint8_t)(new_menu_select);
ret_val = ad77681_scratchpad(device_adc, &chceck_sequence);
pc.printf(" Insered sequence: %d\n Returned sequence: %d\n", new_menu_select, chceck_sequence);
if (ret_val == SUCCESS)
pc.printf(" SUCCESS!\n");
else
pc.printf(" FAILURE!\n");
} else
pc.printf(" Invalid value\n");
print_prompt();
}
/**
* Start with the piezo accelerometer offset compensation
* The offset compenzation process uses a successive approximation model
* There is lot of averaging going on, because of quite noisy piezo accelerometer
* It will take some time
*/
void static menu_21_piezo_offset(void)
{
uint8_t ltc2606_res = 16;
uint32_t dac_code = 0;
uint32_t dac_code_arr[16];
double mean_voltage = 0.0, min_voltage;
double mean_voltage_arr[16];
int8_t sar_loop, min_find, min_index;
uint16_t SINC3_odr;
// Low power mode and MCLK/16
ad77681_set_power_mode(device_adc, AD77681_ECO);
ad77681_set_mclk_div(device_adc, AD77681_MCLK_DIV_16);
// 4SPS = 7999 SINC3, 10SPS = 3199 SINC3, 50SPS = 639 SINC3
ad77681_SINC3_ODR(device_adc, &SINC3_odr, 4);
// Set the oversamplig ratio to high value, to extract DC
ad77681_set_filter_type(device_adc, AD77681_SINC5_FIR_DECx32, AD77681_SINC3, SINC3_odr);
// successive approximation algorithm
pc.printf("\nInitialize SAR loop (DAC MSB set to high)\n");
// Set DAC code to half scale
dac_code = (1 << (ltc2606_res - 1 ));
// Update output of the DAC
ltc26x6_write_code(device_dac, write_update_command, dac_code);
// Wait for DAC output to settle
wait_ms(500);
// Set desired number of samples for every iteration
measured_data.samples = 100;
measured_data.finish = false;
measured_data.count = 0;
// Take X number of samples
cont_sampling();
// Get the mean voltage of taken samples stroed in the measured_data strucutre
get_mean_voltage(&measured_data, &mean_voltage);
// Print the mean ADC read voltage for a given DAC code
pc.printf("DAC code:%x\t\tMean Voltage: %.6f\n", dac_code, mean_voltage);
// Store the initial DAC code in the array
dac_code_arr[ltc2606_res - 1] = dac_code;
// Store the initial mean voltage in the array
mean_voltage_arr[ltc2606_res - 1] = mean_voltage;
for ( sar_loop = ltc2606_res - 1; sar_loop > 0; sar_loop--) {
// Check if the mean voltage is positive or negative
if (mean_voltage > 0) {
dac_code = dac_code + (1 << (sar_loop - 1));
pc.printf("UP\n\n");
} else {
dac_code = dac_code - (1 << (sar_loop)) + (1 << (sar_loop-1));
pc.printf("DOWN\n\n");
}
// Print loop coard
pc.printf("SAR loop #: %d\n",sar_loop);
// Update output of the DAC
ltc26x6_write_code(device_dac, write_update_command, dac_code);
// Wait for DAC output to settle
wait_ms(500);
// Clear data finish flag
measured_data.finish = false;
measured_data.count = 0;
// Take X number of samples
cont_sampling();
// Get the mean voltage of taken samples stroed in the measured_data strucutre
get_mean_voltage(&measured_data, &mean_voltage);
pc.printf("DAC code:%x\t\tMean Voltage: %.6f\n", dac_code, mean_voltage);
dac_code_arr[sar_loop - 1] = dac_code;
mean_voltage_arr[sar_loop - 1] = mean_voltage;
}
min_voltage = abs(mean_voltage_arr[0]);
for (min_find = 0; min_find < 16; min_find++) {
if (min_voltage > abs(mean_voltage_arr[min_find])) {
min_voltage = abs(mean_voltage_arr[min_find]);
min_index = min_find;
}
}
ltc26x6_write_code(device_dac, write_update_command, dac_code_arr[min_index]);
// Wait for DAC output to settle
wait_ms(500);
// Print the final DAC code
pc.printf("\nFinal DAC code set to:%x\t\tFinal Mean Voltage: %.6f\n", dac_code_arr[min_index], mean_voltage_arr[min_index]);
// Set to original filter
ad77681_set_filter_type(device_adc, AD77681_SINC5_FIR_DECx32, AD77681_FIR, 0);
ad77681_update_sample_rate(device_adc);
pc.printf("\nOffset compenzation done!\n");
print_prompt();
}
/**
* Get mean from sampled data
* @param mean_voltage Mean Voltage
* @param measured_data The structure carying measured data
*/
void static get_mean_voltage(struct adc_data *measured_data, double *mean_voltage)
{
int32_t shifted_data;
double sum = 0, voltage = 0;
uint16_t i;
for ( i = 0; i < measured_data->samples; i++) {
ad77681_data_to_voltage(device_adc, &measured_data->raw_data[i], &voltage);
sum += voltage;
}
*mean_voltage = (double)(sum / (double)(measured_data->samples));
}
/**
* Set output of the on-board DAC in codes or in voltage
*
*/
void static menu_22_set_DAC_output(void)
{
int16_t dac_status;
uint16_t code ;
uint32_t new_menu_select, new_dac;
float dac_voltage;
// Gain factor of the on-board DAC buffer, to have full 5V range(ADA4807-1ARJZ)
// Non-inverting op-amp resistor ratio => 1 + (2.7 k ohm / 2.7 k ohm)
float buffer_gain = 2;
pc.printf(" Set DAC output: \n");
pc.printf(" 1 - Voltage\n");
pc.printf(" 2 - Codes\n");
pc.printf(" Select an option: \n");
getUserInput(&new_menu_select);
switch (new_menu_select) {
case 1:
pc.printf(" Set DAC output in mV: ");
getUserInput(&new_dac);
dac_voltage = ((float)(new_dac) / 1000.0) / buffer_gain;
ltc26x6_voltage_to_code(device_dac, dac_voltage, &code);
ltc26x6_write_code(device_dac, write_update_command, code);
if (dac_status == SUCCESS)
pc.printf("%.3f V at Shift output\n\n", dac_voltage * buffer_gain);
else if (dac_status == LTC26X6_CODE_OVERFLOW)
pc.printf("%.3f V at Shift output, OVERFLOW!\n\n", dac_voltage * buffer_gain);
else if (dac_status == LTC26X6_CODE_UNDERFLOW)
pc.printf("%.3f V at Shift output, UNDERFLOW!\n\n", dac_voltage * buffer_gain);
break;
case 2:
pc.printf(" Set DAC codes in decimal form: ");
getUserInput(&new_dac);
ltc26x6_write_code(device_dac, write_update_command, new_dac);
pc.printf("%x at DAC output\n\n", new_dac);
break;
default:
pc.printf(" Invalid option\n");
break;
}
print_prompt();
}
/**
* Prints out an array in binary form
*
*/
void static print_binary(uint8_t number, char *binary_number)
{
for (int8_t i = 7; i >= 0; i--) {
if (number & 1)
binary_number[i] = '1';
else
binary_number[i] = '0';
number >>= 1;
}
}
/**
* Setup SDP-K1 GPIOs
*
*
*/
void static sdpk1_gpio_setup(void)
{
// Enable DAC buffer & other buffer
buffer_en = GPIO_HIGH;
// Turn on onboard red LED
led_red = GPIO_HIGH;
// Turn on onboard blue LED
led_blue = GPIO_HIGH;
}