Revision 0:5a3104f02775, committed 2020-06-28

Comitter:

imanomadao

Date:

Sun Jun 28 11:10:43 2020 +0000

Commit message:

a;

Changed in this revision

--- /dev/null	Thu Jan 01 00:00:00 1970 +0000
+++ b/MPU9255.cpp	Sun Jun 28 11:10:43 2020 +0000
@@ -0,0 +1,532 @@
+#include"MPU9255.h"
+
+//-----------------
+//private functions
+//-----------------
+
+void MPU9255::writeByte(uint8_t address, uint8_t subAddress, uint8_t data)
+{
+   char data_write[2];
+   data_write[0] = subAddress;
+   data_write[1] = data;
+   i2c.write(address, data_write, 2, 0);
+}
+
+char MPU9255::readByte(uint8_t address, uint8_t subAddress)
+{
+    char data[1]; // `data` will store the register data     
+    char data_write[1];
+    data_write[0] = subAddress;
+    i2c.write(address, data_write, 1, 1); // no stop
+    i2c.read(address, data, 1, 0); 
+    return data[0]; 
+}
+
+void MPU9255::readBytes(uint8_t address, uint8_t subAddress, uint8_t count, uint8_t * dest)
+{     
+    char data[14];
+    char data_write[1];
+    data_write[0] = subAddress;
+    i2c.write(address, data_write, 1, 1); // no stop
+    i2c.read(address, data, count, 0); 
+    for(int ii = 0; ii < count; ii++) 
+    {
+        dest[ii] = data[ii];
+    }
+} 
+
+
+//----------------
+//public functions
+//----------------
+
+MPU9255::MPU9255(PinName sda, PinName scl, RawSerial* serial_p)
+    : i2c_p(new I2C(sda,scl)), i2c(*i2c_p), pc_p(serial_p)
+{
+    i2c.frequency(40000);
+}
+
+MPU9255::~MPU9255() {}
+
+uint8_t MPU9255::whoami_mpu9255()
+{
+    uint8_t a = readByte(MPU9255_ADDRESS, WHO_AM_I_MPU9255);
+    return a;
+}
+
+void MPU9255::reset_mpu9255()
+{
+    writeByte(MPU9255_ADDRESS, PWR_MGMT_1, 0x80);
+    wait_ms(10);
+}
+
+void MPU9255::selftest_mpu9255(float * destination) // Should return percent deviation from factory trim values, +/- 14 or less deviation is a pass
+{
+    uint8_t rawData[6] = {0, 0, 0, 0, 0, 0};
+    uint8_t selfTest[6];
+    int32_t gAvg[3] = {0}, aAvg[3] = {0}, aSTAvg[3] = {0}, gSTAvg[3] = {0};
+    float factoryTrim[6];
+    uint8_t FS = 0;
+   
+    writeByte(MPU9255_ADDRESS, SMPLRT_DIV, 0x00);    // Set gyro sample rate to 1 kHz
+    writeByte(MPU9255_ADDRESS, CONFIG, 0x02);        // Set gyro sample rate to 1 kHz and DLPF to 92 Hz
+    writeByte(MPU9255_ADDRESS, GYRO_CONFIG, 1<<FS);  // Set full scale range for the gyro to 250 dps
+    writeByte(MPU9255_ADDRESS, ACCEL_CONFIG2, 0x02); // Set accelerometer rate to 1 kHz and bandwidth to 92 Hz
+    writeByte(MPU9255_ADDRESS, ACCEL_CONFIG, 1<<FS); // Set full scale range for the accelerometer to 2 g      
+
+    for( int ii = 0; ii < 200; ii++)   // get average current values of gyro and acclerometer
+    {  
+        readBytes(MPU9255_ADDRESS, ACCEL_XOUT_H, 6, &rawData[0]);        // Read the six raw data registers into data array
+        aAvg[0] += (int16_t)(((int16_t)rawData[0] << 8) | rawData[1]) ;  // Turn the MSB and LSB into a signed 16-bit value
+        aAvg[1] += (int16_t)(((int16_t)rawData[2] << 8) | rawData[3]) ;  
+        aAvg[2] += (int16_t)(((int16_t)rawData[4] << 8) | rawData[5]) ; 
+  
+        readBytes(MPU9255_ADDRESS, GYRO_XOUT_H, 6, &rawData[0]);       // Read the six raw data registers sequentially into data array
+        gAvg[0] += (int16_t)(((int16_t)rawData[0] << 8) | rawData[1]) ;  // Turn the MSB and LSB into a signed 16-bit value
+        gAvg[1] += (int16_t)(((int16_t)rawData[2] << 8) | rawData[3]) ;  
+        gAvg[2] += (int16_t)(((int16_t)rawData[4] << 8) | rawData[5]) ; 
+    }
+  
+    for (int ii =0; ii < 3; ii++)   // Get average of 200 values and store as average current readings
+    {
+        aAvg[ii] /= 200;
+        gAvg[ii] /= 200;
+    }
+  
+// Configure the accelerometer for self-test
+    writeByte(MPU9255_ADDRESS, ACCEL_CONFIG, 0xE0); // Enable self test on all three axes and set accelerometer range to +/- 2 g
+    writeByte(MPU9255_ADDRESS, GYRO_CONFIG,  0xE0); // Enable self test on all three axes and set gyro range to +/- 250 degrees/s
+    wait_ms(25);  // Delay a while to let the device stabilize
+
+    for( int ii = 0; ii < 200; ii++)   // get average self-test values of gyro and acclerometer
+    {
+        readBytes(MPU9255_ADDRESS, ACCEL_XOUT_H, 6, &rawData[0]);  // Read the six raw data registers into data array
+        aSTAvg[0] += (int16_t)(((int16_t)rawData[0] << 8) | rawData[1]) ;  // Turn the MSB and LSB into a signed 16-bit value
+        aSTAvg[1] += (int16_t)(((int16_t)rawData[2] << 8) | rawData[3]) ;  
+        aSTAvg[2] += (int16_t)(((int16_t)rawData[4] << 8) | rawData[5]) ; 
+  
+        readBytes(MPU9255_ADDRESS, GYRO_XOUT_H, 6, &rawData[0]);  // Read the six raw data registers sequentially into data array
+        gSTAvg[0] += (int16_t)(((int16_t)rawData[0] << 8) | rawData[1]) ;  // Turn the MSB and LSB into a signed 16-bit value
+        gSTAvg[1] += (int16_t)(((int16_t)rawData[2] << 8) | rawData[3]) ;  
+        gSTAvg[2] += (int16_t)(((int16_t)rawData[4] << 8) | rawData[5]) ; 
+    }
+  
+    for (int ii =0; ii < 3; ii++)   // Get average of 200 values and store as average self-test readings
+    {
+        aSTAvg[ii] /= 200;
+        gSTAvg[ii] /= 200;
+    }   
+  
+ // Configure the gyro and accelerometer for normal operation
+    writeByte(MPU9255_ADDRESS, ACCEL_CONFIG, 0x00);  
+    writeByte(MPU9255_ADDRESS, GYRO_CONFIG,  0x00);  
+    wait_ms(25);  // Delay a while to let the device stabilize
+   
+   // Retrieve accelerometer and gyro factory Self-Test Code from USR_Reg
+    selfTest[0] = readByte(MPU9255_ADDRESS, SELF_TEST_X_ACCEL); // X-axis accel self-test results
+    selfTest[1] = readByte(MPU9255_ADDRESS, SELF_TEST_Y_ACCEL); // Y-axis accel self-test results
+    selfTest[2] = readByte(MPU9255_ADDRESS, SELF_TEST_Z_ACCEL); // Z-axis accel self-test results
+    selfTest[3] = readByte(MPU9255_ADDRESS, SELF_TEST_X_GYRO);  // X-axis gyro self-test results
+    selfTest[4] = readByte(MPU9255_ADDRESS, SELF_TEST_Y_GYRO);  // Y-axis gyro self-test results
+    selfTest[5] = readByte(MPU9255_ADDRESS, SELF_TEST_Z_GYRO);  // Z-axis gyro self-test results
+
+  // Retrieve factory self-test value from self-test code reads
+    factoryTrim[0] = (float)(2620/1<<FS)*(pow( 1.01 , ((float)selfTest[0] - 1.0) )); // FT[Xa] factory trim calculation
+    factoryTrim[1] = (float)(2620/1<<FS)*(pow( 1.01 , ((float)selfTest[1] - 1.0) )); // FT[Ya] factory trim calculation
+    factoryTrim[2] = (float)(2620/1<<FS)*(pow( 1.01 , ((float)selfTest[2] - 1.0) )); // FT[Za] factory trim calculation
+    factoryTrim[3] = (float)(2620/1<<FS)*(pow( 1.01 , ((float)selfTest[3] - 1.0) )); // FT[Xg] factory trim calculation
+    factoryTrim[4] = (float)(2620/1<<FS)*(pow( 1.01 , ((float)selfTest[4] - 1.0) )); // FT[Yg] factory trim calculation
+    factoryTrim[5] = (float)(2620/1<<FS)*(pow( 1.01 , ((float)selfTest[5] - 1.0) )); // FT[Zg] factory trim calculation
+ 
+ // Report results as a ratio of (STR - FT)/FT; the change from Factory Trim of the Self-Test Response
+ // To get percent, must multiply by 100
+    for (int i = 0; i < 3; i++) 
+    {
+        destination[i]   = 100.0f*((float)(aSTAvg[i] - aAvg[i]))/factoryTrim[i] - 100.0f;   // Report percent differences
+        destination[i+3] = 100.0f*((float)(gSTAvg[i] - gAvg[i]))/factoryTrim[i+3] - 100.0f; // Report percent differences
+    }
+   
+}
+
+float MPU9255::getMres(uint8_t Mscale) 
+{
+    float _mRes;
+    switch (Mscale)
+    {
+   // Possible magnetometer scales (and their register bit settings) are:
+  // 14 bit resolution (0) and 16 bit resolution (1)
+        case MFS_14BITS:
+            _mRes = 10.*4912./8190.; // Proper scale to return milliGauss
+            return _mRes;
+            //break;
+        case MFS_16BITS:
+            _mRes = 10.*4912./32760.0; // Proper scale to return milliGauss (4912/32760=0.15)
+            return _mRes;              // convert 'μT' to 'mG' 
+            //break;
+    }
+}
+
+float MPU9255::getGres(uint8_t Gscale)
+{
+    float _gRes;
+    switch (Gscale)
+    {
+  // Possible gyro scales (and their register bit settings) are:
+  // 250 DPS (00), 500 DPS (01), 1000 DPS (10), and 2000 DPS  (11). 
+        case GFS_250DPS:
+            _gRes = 250.0/32768.0;
+            return _gRes;
+            //break;
+        case GFS_500DPS:
+            _gRes = 500.0/32768.0;
+            return _gRes;
+            //break;
+        case GFS_1000DPS:
+            _gRes = 1000.0/32768.0;
+            return _gRes;
+            //break;
+        case GFS_2000DPS:
+            _gRes = 2000.0/32768.0;
+            return _gRes;
+            //break;
+    }
+}
+
+float MPU9255::getAres(uint8_t Ascale)
+{
+    float _aRes;
+    switch (Ascale)
+    {
+  // Possible accelerometer scales (and their register bit settings) are:
+  // 2 Gs (00), 4 Gs (01), 8 Gs (10), and 16 Gs  (11). 
+        // Here's a bit of an algorith to calculate DPS/(ADC tick) based on that 2-bit value:
+        case AFS_2G:
+            _aRes = 2.0f/32768.0f;
+            return _aRes;
+            //break;
+        case AFS_4G:
+            _aRes = 4.0f/32768.0f;
+            return _aRes;
+            //break;
+        case AFS_8G:
+            _aRes = 8.0f/32768.0f;
+            return _aRes;
+            //break;
+        case AFS_16G:
+            _aRes = 16.0f/32768.0f;
+            return _aRes;
+            //break;
+    }
+}
+
+void MPU9255::calibrate_mpu9255(float * dest1, float * dest2)
+{  
+    uint8_t data[12]; // data array to hold accelerometer and gyro x, y, z, data
+    uint16_t ii, packet_count, fifo_count;
+    int32_t gyro_bias[3]  = {0, 0, 0}, accel_bias[3] = {0, 0, 0};
+  
+    // reset device
+    writeByte(MPU9255_ADDRESS, PWR_MGMT_1, 0x80); // Write a one to bit 7 reset bit; toggle reset device
+    wait_ms(100);
+   
+    // get stable time source; Auto select clock source to be PLL gyroscope reference if ready 
+    // else use the internal oscillator, bits 2:0 = 001
+    writeByte(MPU9255_ADDRESS, PWR_MGMT_1, 0x01);  
+    writeByte(MPU9255_ADDRESS, PWR_MGMT_2, 0x00);
+    wait_ms(200);                                    
+
+    // Configure device for bias calculation
+    writeByte(MPU9255_ADDRESS, INT_ENABLE, 0x00);   // Disable all interrupts
+    writeByte(MPU9255_ADDRESS, FIFO_EN, 0x00);      // Disable FIFO
+    writeByte(MPU9255_ADDRESS, PWR_MGMT_1, 0x00);   // Turn on internal clock source
+    writeByte(MPU9255_ADDRESS, I2C_MST_CTRL, 0x00); // Disable I2C master
+    writeByte(MPU9255_ADDRESS, USER_CTRL, 0x00);    // Disable FIFO and I2C master modes
+    writeByte(MPU9255_ADDRESS, USER_CTRL, 0x0C);    // Reset FIFO and DMP
+    wait_ms(15);
+  
+    // Configure MPU6050 gyro and accelerometer for bias calculation
+    writeByte(MPU9255_ADDRESS, CONFIG, 0x01);      // Set low-pass filter to 188 Hz
+    writeByte(MPU9255_ADDRESS, SMPLRT_DIV, 0x00);  // Set sample rate to 1 kHz
+    writeByte(MPU9255_ADDRESS, GYRO_CONFIG, 0x00);  // Set gyro full-scale to 250 degrees per second, maximum sensitivity
+    writeByte(MPU9255_ADDRESS, ACCEL_CONFIG, 0x00); // Set accelerometer full-scale to 2 g, maximum sensitivity
+ 
+    uint16_t  gyrosensitivity  = 131;   // = 131 LSB/degrees/sec
+    uint16_t  accelsensitivity = 16384;  // = 16384 LSB/g
+
+    // Configure FIFO to capture accelerometer and gyro data for bias calculation
+    writeByte(MPU9255_ADDRESS, USER_CTRL, 0x40);   // Enable FIFO  
+    writeByte(MPU9255_ADDRESS, FIFO_EN, 0x78);     // Enable gyro and accelerometer sensors for FIFO  (max size 512 bytes in MPU-9150)
+    wait_ms(40); // accumulate 40 samples in 40 milliseconds = 480 bytes
+
+// At end of sample accumulation, turn off FIFO sensor read
+    writeByte(MPU9255_ADDRESS, FIFO_EN, 0x00);        // Disable gyro and accelerometer sensors for FIFO
+    readBytes(MPU9255_ADDRESS, FIFO_COUNTH, 2, &data[0]); // read FIFO sample count
+    fifo_count = ((uint16_t)data[0] << 8) | data[1];
+    packet_count = fifo_count/12;// How many sets of full gyro and accelerometer data for averaging
+  
+    for (ii = 0; ii < packet_count; ii++) 
+    {
+        int16_t accel_temp[3] = {0, 0, 0}, gyro_temp[3] = {0, 0, 0};
+        readBytes(MPU9255_ADDRESS, FIFO_R_W, 12, &data[0]); // read data for averaging
+        accel_temp[0] = (int16_t) (((int16_t)data[0] << 8) | data[1]  ) ;  // Form signed 16-bit integer for each sample in FIFO
+        accel_temp[1] = (int16_t) (((int16_t)data[2] << 8) | data[3]  ) ;
+        accel_temp[2] = (int16_t) (((int16_t)data[4] << 8) | data[5]  ) ;    
+        gyro_temp[0]  = (int16_t) (((int16_t)data[6] << 8) | data[7]  ) ;
+        gyro_temp[1]  = (int16_t) (((int16_t)data[8] << 8) | data[9]  ) ;
+        gyro_temp[2]  = (int16_t) (((int16_t)data[10] << 8) | data[11]) ;
+    
+        accel_bias[0] += (int32_t) accel_temp[0]; // Sum individual signed 16-bit biases to get accumulated signed 32-bit biases
+        accel_bias[1] += (int32_t) accel_temp[1];
+        accel_bias[2] += (int32_t) accel_temp[2];
+        gyro_bias[0]  += (int32_t) gyro_temp[0];
+        gyro_bias[1]  += (int32_t) gyro_temp[1];
+        gyro_bias[2]  += (int32_t) gyro_temp[2];
+            
+    }
+        
+    accel_bias[0] /= (int32_t) packet_count; // Normalize sums to get average count biases
+    accel_bias[1] /= (int32_t) packet_count;
+    accel_bias[2] /= (int32_t) packet_count;
+    gyro_bias[0]  /= (int32_t) packet_count;
+    gyro_bias[1]  /= (int32_t) packet_count;
+    gyro_bias[2]  /= (int32_t) packet_count;
+    
+    if(accel_bias[2] > 0L) {accel_bias[2] -= (int32_t) accelsensitivity;}  // Remove gravity from the z-axis accelerometer bias calculation
+    else {accel_bias[2] += (int32_t) accelsensitivity;}
+   
+// Construct the gyro biases for push to the hardware gyro bias registers, which are reset to zero upon device startup
+    data[0] = (-gyro_bias[0]/4  >> 8) & 0xFF; // Divide by 4 to get 32.9 LSB per deg/s to conform to expected bias input format
+    data[1] = (-gyro_bias[0]/4)       & 0xFF; // Biases are additive, so change sign on calculated average gyro biases
+    data[2] = (-gyro_bias[1]/4  >> 8) & 0xFF;
+    data[3] = (-gyro_bias[1]/4)       & 0xFF;
+    data[4] = (-gyro_bias[2]/4  >> 8) & 0xFF;
+    data[5] = (-gyro_bias[2]/4)       & 0xFF;
+  
+// Push gyro biases to hardware registers
+    writeByte(MPU9255_ADDRESS, XG_OFFSET_H, data[0]);
+    writeByte(MPU9255_ADDRESS, XG_OFFSET_L, data[1]);
+    writeByte(MPU9255_ADDRESS, YG_OFFSET_H, data[2]);
+    writeByte(MPU9255_ADDRESS, YG_OFFSET_L, data[3]);
+    writeByte(MPU9255_ADDRESS, ZG_OFFSET_H, data[4]);
+    writeByte(MPU9255_ADDRESS, ZG_OFFSET_L, data[5]);
+  
+// Output scaled gyro biases for display in the main program
+    dest1[0] = (float) gyro_bias[0]/(float) gyrosensitivity;  
+    dest1[1] = (float) gyro_bias[1]/(float) gyrosensitivity;
+    dest1[2] = (float) gyro_bias[2]/(float) gyrosensitivity;
+
+// Construct the accelerometer biases for push to the hardware accelerometer bias registers. These registers contain
+// factory trim values which must be added to the calculated accelerometer biases; on boot up these registers will hold
+// non-zero values. In addition, bit 0 of the lower byte must be preserved since it is used for temperature
+// compensation calculations. Accelerometer bias registers expect bias input as 2048 LSB per g, so that
+// the accelerometer biases calculated above must be divided by 8.
+
+    int32_t accel_bias_reg[3] = {0, 0, 0}; // A place to hold the factory accelerometer trim biases
+    readBytes(MPU9255_ADDRESS, XA_OFFSET_H, 2, &data[0]); // Read factory accelerometer trim values
+    accel_bias_reg[0] = (int32_t) (((int16_t)data[0] << 8) | data[1]);
+    readBytes(MPU9255_ADDRESS, YA_OFFSET_H, 2, &data[0]);
+    accel_bias_reg[1] = (int32_t) (((int16_t)data[0] << 8) | data[1]);
+    readBytes(MPU9255_ADDRESS, ZA_OFFSET_H, 2, &data[0]);
+    accel_bias_reg[2] = (int32_t) (((int16_t)data[0] << 8) | data[1]);
+  
+    uint32_t mask = 1uL; // Define mask for temperature compensation bit 0 of lower byte of accelerometer bias registers
+    uint8_t mask_bit[3] = {0, 0, 0}; // Define array to hold mask bit for each accelerometer bias axis
+  
+    for(ii = 0; ii < 3; ii++) 
+    {
+        if((accel_bias_reg[ii] & mask)) mask_bit[ii] = 0x01; // If temperature compensation bit is set, record that fact in mask_bit
+    }
+  
+  // Construct total accelerometer bias, including calculated average accelerometer bias from above
+    accel_bias_reg[0] -= (accel_bias[0]/8); // Subtract calculated averaged accelerometer bias scaled to 2048 LSB/g (16 g full scale)
+    accel_bias_reg[1] -= (accel_bias[1]/8);
+    accel_bias_reg[2] -= (accel_bias[2]/8);
+  
+    data[0] = (accel_bias_reg[0] >> 8) & 0xFF;
+    data[1] = (accel_bias_reg[0])      & 0xFF;
+    data[1] = data[1] | mask_bit[0]; // preserve temperature compensation bit when writing back to accelerometer bias registers
+    data[2] = (accel_bias_reg[1] >> 8) & 0xFF;
+    data[3] = (accel_bias_reg[1])      & 0xFF;
+    data[3] = data[3] | mask_bit[1]; // preserve temperature compensation bit when writing back to accelerometer bias registers
+    data[4] = (accel_bias_reg[2] >> 8) & 0xFF;
+    data[5] = (accel_bias_reg[2])      & 0xFF;
+    data[5] = data[5] | mask_bit[2]; // preserve temperature compensation bit when writing back to accelerometer bias registers
+ 
+// Apparently this is not working for the acceleration biases in the MPU-9255
+// Are we handling the temperature correction bit properly?
+// Push accelerometer biases to hardware registers
+//  writeByte(MPU9255_ADDRESS, XA_OFFSET_H, data[0]);
+//  writeByte(MPU9255_ADDRESS, XA_OFFSET_L, data[1]);
+//  writeByte(MPU9255_ADDRESS, YA_OFFSET_H, data[2]);
+//  writeByte(MPU9255_ADDRESS, YA_OFFSET_L, data[3]);
+//  writeByte(MPU9255_ADDRESS, ZA_OFFSET_H, data[4]);
+//  writeByte(MPU9255_ADDRESS, ZA_OFFSET_L, data[5]);
+
+// Output scaled accelerometer biases for display in the main program
+    dest2[0] = (float)accel_bias[0]/(float)accelsensitivity; 
+    dest2[1] = (float)accel_bias[1]/(float)accelsensitivity;
+    dest2[2] = (float)accel_bias[2]/(float)accelsensitivity;
+}
+
+void MPU9255::init_mpu9255(uint8_t Ascale, uint8_t Gscale, uint8_t sampleRate)
+{  
+ // wake up device
+    writeByte(MPU9255_ADDRESS, PWR_MGMT_1, 0x00); // Clear sleep mode bit (6), enable all sensors 
+    wait_ms(100); // Wait for all registers to reset 
+
+ // get stable time source
+    writeByte(MPU9255_ADDRESS, PWR_MGMT_1, 0x01);  // Auto select clock source to be PLL gyroscope reference if ready else
+    wait_ms(200); 
+  
+ // Configure Gyro and Thermometer
+ // Disable FSYNC and set thermometer and gyro bandwidth to 41 and 42 Hz, respectively; 
+ // minimum delay time for this setting is 5.9 ms, which means sensor fusion update rates cannot
+ // be higher than 1 / 0.0059 = 170 Hz
+ // DLPF_CFG = bits 2:0 = 011; this limits the sample rate to 1000 Hz for both
+ // With the MPU9255, it is possible to get gyro sample rates of 32 kHz (!), 8 kHz, or 1 kHz
+    writeByte(MPU9255_ADDRESS, CONFIG, 0x03);  
+
+ // Set sample rate = gyroscope output rate/(1 + SMPLRT_DIV)
+    writeByte(MPU9255_ADDRESS, SMPLRT_DIV, sampleRate);  // Use a 200 Hz rate; a rate consistent with the filter update rate 
+                                                       // determined inset in CONFIG above
+ 
+ // Set gyroscope full scale range
+ // Range selects FS_SEL and AFS_SEL are 0 - 3, so 2-bit values are left-shifted into positions 4:3
+    uint8_t c = readByte(MPU9255_ADDRESS, GYRO_CONFIG); // get current GYRO_CONFIG register value
+ // c = c & ~0xE0; // Clear self-test bits [7:5] 
+    c = c & ~0x02; // Clear Fchoice bits [1:0] 
+    c = c & ~0x18; // Clear AFS bits [4:3]
+    c = c | Gscale << 3; // Set full scale range for the gyro
+ // c =| 0x00; // Set Fchoice for the gyro to 11 by writing its inverse to bits 1:0 of GYRO_CONFIG
+    writeByte(MPU9255_ADDRESS, GYRO_CONFIG, c ); // Write new GYRO_CONFIG value to register
+  
+ // Set accelerometer full-scale range configuration
+    c = readByte(MPU9255_ADDRESS, ACCEL_CONFIG); // get current ACCEL_CONFIG register value
+ // c = c & ~0xE0; // Clear self-test bits [7:5] 
+    c = c & ~0x18;  // Clear AFS bits [4:3]
+    c = c | Ascale << 3; // Set full scale range for the accelerometer 
+    writeByte(MPU9255_ADDRESS, ACCEL_CONFIG, c); // Write new ACCEL_CONFIG register value
+
+ // Set accelerometer sample rate configuration
+ // It is possible to get a 4 kHz sample rate from the accelerometer by choosing 1 for
+ // accel_fchoice_b bit [3]; in this case the bandwidth is 1.13 kHz
+    c = readByte(MPU9255_ADDRESS, ACCEL_CONFIG2); // get current ACCEL_CONFIG2 register value
+    c = c & ~0x0F; // Clear accel_fchoice_b (bit 3) and A_DLPFG (bits [2:0])  
+    c = c | 0x03;  // Set accelerometer rate to 1 kHz and bandwidth to 41 Hz
+    writeByte(MPU9255_ADDRESS, ACCEL_CONFIG2, c); // Write new ACCEL_CONFIG2 register value
+
+ // The accelerometer, gyro, and thermometer are set to 1 kHz sample rates, 
+ // but all these rates are further reduced by a factor of 5 to 200 Hz because of the SMPLRT_DIV setting
+
+  // Configure Interrupts and Bypass Enable
+  // Set interrupt pin active high, push-pull, hold interrupt pin level HIGH until interrupt cleared,
+  // clear on read of INT_STATUS, and enable I2C_BYPASS_EN so additional chips 
+  // can join the I2C bus and all can be controlled by the Arduino as master
+    writeByte(MPU9255_ADDRESS, INT_PIN_CFG, 0x10);  // INT is 50 microsecond pulse and any read to clear  
+    writeByte(MPU9255_ADDRESS, INT_ENABLE, 0x01);  // Enable data ready (bit 0) interrupt
+    wait_ms(100);
+ 
+    writeByte(MPU9255_ADDRESS, USER_CTRL, 0x20);          // Enable I2C Master mode  
+    writeByte(MPU9255_ADDRESS, I2C_MST_CTRL, 0x1D);       // I2C configuration STOP after each transaction, master I2C bus at 400 KHz
+    writeByte(MPU9255_ADDRESS, I2C_MST_DELAY_CTRL, 0x81); // Use blocking data retreival and enable delay for mag sample rate mismatch
+    writeByte(MPU9255_ADDRESS, I2C_SLV4_CTRL, 0x01);      // Delay mag data retrieval to once every other accel/gyro data sample
+}
+
+
+uint8_t MPU9255::get_AK8963CID()
+{
+    writeByte(MPU9255_ADDRESS, USER_CTRL, 0x20);    // Enable I2C Master mode  
+    writeByte(MPU9255_ADDRESS, I2C_MST_CTRL, 0x0D); // I2C configuration multi-master I2C 400KHz
+
+    writeByte(MPU9255_ADDRESS, I2C_SLV0_ADDR, AK8963_ADDRESS | 0x80);    // Set the I2C slave address of AK8963 and set for read.
+    writeByte(MPU9255_ADDRESS, I2C_SLV0_REG, WHO_AM_I_AK8963);           // I2C slave 0 register address from where to begin data transfer
+    writeByte(MPU9255_ADDRESS, I2C_SLV0_CTRL, 0x81);                     // Enable I2C and transfer 1 byte
+    wait_ms(10);
+    uint8_t c = readByte(MPU9255_ADDRESS, EXT_SENS_DATA_00);             // Read the WHO_AM_I byte
+    return c;
+}
+
+void MPU9255::init_AK8963Slave(uint8_t Mscale, uint8_t Mmode, float * magCalibration)
+{
+   // First extract the factory calibration for each magnetometer axis
+    uint8_t rawData[3];  // x/y/z gyro calibration data stored here
+
+    writeByte(MPU9255_ADDRESS, I2C_SLV0_ADDR, AK8963_ADDRESS);           // Set the I2C slave address of AK8963 and set for write.
+    writeByte(MPU9255_ADDRESS, I2C_SLV0_REG, AK8963_CNTL2);              // I2C slave 0 register address from where to begin data transfer
+    writeByte(MPU9255_ADDRESS, I2C_SLV0_DO, 0x01);                       // Reset AK8963
+    writeByte(MPU9255_ADDRESS, I2C_SLV0_CTRL, 0x81);                     // Enable I2C and write 1 byte
+    wait_ms(50);
+    writeByte(MPU9255_ADDRESS, I2C_SLV0_ADDR, AK8963_ADDRESS);           // Set the I2C slave address of AK8963 and set for write.
+    writeByte(MPU9255_ADDRESS, I2C_SLV0_REG, AK8963_CNTL);               // I2C slave 0 register address from where to begin data transfer
+    writeByte(MPU9255_ADDRESS, I2C_SLV0_DO, 0x00);                       // Power down magnetometer  
+    writeByte(MPU9255_ADDRESS, I2C_SLV0_CTRL, 0x81);                     // Enable I2C and write 1 byte
+    wait_ms(50);
+    writeByte(MPU9255_ADDRESS, I2C_SLV0_ADDR, AK8963_ADDRESS);           // Set the I2C slave address of AK8963 and set for write.
+    writeByte(MPU9255_ADDRESS, I2C_SLV0_REG, AK8963_CNTL);               // I2C slave 0 register address from where to begin data transfer
+    writeByte(MPU9255_ADDRESS, I2C_SLV0_DO, 0x0F);                       // Enter fuze mode
+    writeByte(MPU9255_ADDRESS, I2C_SLV0_CTRL, 0x81);                     // Enable I2C and write 1 byte
+    wait_ms(50);
+   
+    writeByte(MPU9255_ADDRESS, I2C_SLV0_ADDR, AK8963_ADDRESS | 0x80);    // Set the I2C slave address of AK8963 and set for read.
+    writeByte(MPU9255_ADDRESS, I2C_SLV0_REG, AK8963_ASAX);               // I2C slave 0 register address from where to begin data transfer
+    writeByte(MPU9255_ADDRESS, I2C_SLV0_CTRL, 0x83);                     // Enable I2C and read 3 bytes
+    wait_ms(50);
+    readBytes(MPU9255_ADDRESS, EXT_SENS_DATA_00, 3, &rawData[0]);        // Read the x-, y-, and z-axis calibration values
+    magCalibration[0] =  (float)(rawData[0] - 128)/256.0f + 1.0f;        // Return x-axis sensitivity adjustment values, etc.
+    magCalibration[1] =  (float)(rawData[1] - 128)/256.0f + 1.0f;  
+    magCalibration[2] =  (float)(rawData[2] - 128)/256.0f + 1.0f; 
+    /*_magCalibration[0] = magCalibration[0];
+    _magCalibration[1] = magCalibration[1];
+    _magCalibration[2] = magCalibration[2];
+    _Mmode = Mmode;*/
+    
+    writeByte(MPU9255_ADDRESS, I2C_SLV0_ADDR, AK8963_ADDRESS);           // Set the I2C slave address of AK8963 and set for write.
+    writeByte(MPU9255_ADDRESS, I2C_SLV0_REG, AK8963_CNTL);               // I2C slave 0 register address from where to begin data transfer
+    writeByte(MPU9255_ADDRESS, I2C_SLV0_DO, 0x00);                       // Power down magnetometer  
+    writeByte(MPU9255_ADDRESS, I2C_SLV0_CTRL, 0x81);                     // Enable I2C and transfer 1 byte
+    wait_ms(50);
+
+    writeByte(MPU9255_ADDRESS, I2C_SLV0_ADDR, AK8963_ADDRESS);           // Set the I2C slave address of AK8963 and set for write.
+    writeByte(MPU9255_ADDRESS, I2C_SLV0_REG, AK8963_CNTL);               // I2C slave 0 register address from where to begin data transfer 
+    // Configure the magnetometer for continuous read and highest resolution
+   // set Mscale bit 4 to 1 (0) to enable 16 (14) bit resolution in CNTL register,
+   // and enable continuous mode data acquisition Mmode (bits [3:0]), 0010 for 8 Hz and 0110 for 100 Hz sample rates
+    writeByte(MPU9255_ADDRESS, I2C_SLV0_DO, Mscale << 4 | Mmode);        // Set magnetometer data resolution and sample ODR
+    writeByte(MPU9255_ADDRESS, I2C_SLV0_CTRL, 0x81);                     // Enable I2C and transfer 1 byte
+    wait_ms(50);
+    writeByte(MPU9255_ADDRESS, I2C_SLV0_ADDR, AK8963_ADDRESS | 0x80);    // Set the I2C slave address of AK8963 and set for read.
+    writeByte(MPU9255_ADDRESS, I2C_SLV0_REG, AK8963_CNTL);               // I2C slave 0 register address from where to begin data transfer
+    writeByte(MPU9255_ADDRESS, I2C_SLV0_CTRL, 0x81);                     // Enable I2C and transfer 1 byte
+    wait_ms(50);
+}
+
+void MPU9255::readMagData_mpu9255(int16_t * destination)
+{
+    uint8_t rawData[7];  // x/y/z gyro register data, ST2 register stored here, must read ST2 at end of data acquisition
+//  readBytes(AK8963_ADDRESS, AK8963_XOUT_L, 7, &rawData[0]);  // Read the six raw data and ST2 registers sequentially into data array
+    writeByte(MPU9255_ADDRESS, I2C_SLV0_ADDR, AK8963_ADDRESS | 0x80);    // Set the I2C slave address of AK8963 and set for read.
+    writeByte(MPU9255_ADDRESS, I2C_SLV0_REG, AK8963_XOUT_L);             // I2C slave 0 register address from where to begin data transfer
+    writeByte(MPU9255_ADDRESS, I2C_SLV0_CTRL, 0x87);                     // Enable I2C and read 7 bytes
+    wait_ms(2);
+    readBytes(MPU9255_ADDRESS, EXT_SENS_DATA_00, 7, &rawData[0]);        // Read the x-, y-, and z-axis calibration values
+    uint8_t c = rawData[6]; // End data read by reading ST2 register
+    if(!(c & 0x08))  // Check if magnetic sensor overflow set, if not then report data
+    {
+        destination[0] = ((int16_t)rawData[1] << 8) | rawData[0] ;  // Turn the MSB and LSB into a signed 16-bit value
+        destination[1] = ((int16_t)rawData[3] << 8) | rawData[2] ;  // Data stored as little Endian
+        destination[2] = ((int16_t)rawData[5] << 8) | rawData[4] ; 
+    }
+}
+
+void MPU9255::readaccgyrodata_mpu9255(int16_t * destination)
+{
+    uint8_t rawData[14];  // x/y/z accel register data stored here
+    readBytes(MPU9255_ADDRESS, ACCEL_XOUT_H, 14, &rawData[0]);  // Read the 14 raw data registers into data array
+    destination[0] = ((int16_t)rawData[0] << 8) | rawData[1] ;  // Turn the MSB and LSB into a signed 16-bit value
+    destination[1] = ((int16_t)rawData[2] << 8) | rawData[3] ;  
+    destination[2] = ((int16_t)rawData[4] << 8) | rawData[5] ; 
+    destination[3] = ((int16_t)rawData[6] << 8) | rawData[7] ;   
+    destination[4] = ((int16_t)rawData[8] << 8) | rawData[9] ;  
+    destination[5] = ((int16_t)rawData[10] << 8) | rawData[11] ;  
+    destination[6] = ((int16_t)rawData[12] << 8) | rawData[13] ; 
+}
\ No newline at end of file

--- /dev/null	Thu Jan 01 00:00:00 1970 +0000
+++ b/MPU9255.h	Sun Jun 28 11:10:43 2020 +0000
@@ -0,0 +1,53 @@
+#ifndef _MPU9255_H_
+#define _MPU9255_H_
+
+#include"mbed.h"
+#include"MPU9255Regs.h"
+
+// Set initial input parameters
+#define  AFS_2G  0
+#define  AFS_4G  1
+#define  AFS_8G  2
+#define  AFS_16G 3
+
+#define  GFS_250DPS  0
+#define  GFS_500DPS  1
+#define  GFS_1000DPS 2
+#define  GFS_2000DPS 3
+
+#define  MFS_14BITS  0 // 0.6 mG per LSB
+#define  MFS_16BITS  1    // 0.15 mG per LSB
+
+#define M_8Hz   0x02
+#define M_100Hz 0x06
+
+
+class MPU9255
+{
+    I2C *i2c_p;
+    I2C &i2c;
+    RawSerial* pc_p;
+    
+    void writeByte(uint8_t address, uint8_t subAddress, uint8_t data);
+    char readByte(uint8_t address, uint8_t subAddress);
+    void readBytes(uint8_t address, uint8_t subAddress, uint8_t count, uint8_t * dest);
+
+public:
+    MPU9255(PinName sda, PinName scl, RawSerial* serial_p);
+    ~MPU9255();
+    
+    void init_mpu9255(uint8_t Ascale, uint8_t Cscale, uint8_t asmpleRate);
+    uint8_t whoami_mpu9255();
+    void reset_mpu9255();
+    void selftest_mpu9255(float * destination);
+    float getAres(uint8_t Ascale);
+    float getGres(uint8_t Gscale);
+    float getMres(uint8_t Mscale);
+    void calibrate_mpu9255(float * dest1, float * dest2);
+    uint8_t get_AK8963CID();
+    void init_AK8963Slave(uint8_t Mscale, uint8_t Mmode, float * magCalibration);
+    void readMagData_mpu9255(int16_t * destination);
+    void readaccgyrodata_mpu9255(int16_t * destination);
+};
+
+#endif
\ No newline at end of file

--- /dev/null	Thu Jan 01 00:00:00 1970 +0000
+++ b/MPU9255Regs.h	Sun Jun 28 11:10:43 2020 +0000
@@ -0,0 +1,154 @@
+#ifndef MPU9250_REGISTER_H
+#define MPU9250_REGISTER_H
+
+// See also MPU-9250 Register Map and Descriptions, Revision 4.0, RM-MPU-9250A-00, Rev. 1.4, 9/9/2013 for registers not listed in 
+// above document; the MPU9250 and MPU9150 are virtually identical but the latter has a different register map
+
+//AK8963 registers
+#define AK8963_ADDRESS   0x0C // used in slave mode, ak8963c's adress is 0x0c
+#define WHO_AM_I_AK8963  0x00 // should return 0x48
+#define INFO             0x01
+#define AK8963_ST1       0x02  // data ready status bit 0
+#define AK8963_XOUT_L    0x03  // data
+#define AK8963_XOUT_H    0x04
+#define AK8963_YOUT_L    0x05
+#define AK8963_YOUT_H    0x06
+#define AK8963_ZOUT_L    0x07
+#define AK8963_ZOUT_H    0x08
+#define AK8963_ST2       0x09  // Data overflow bit 3 and data read error status bit 2
+#define AK8963_CNTL      0x0A  // Power down (0000), single-measurement (0001), self-test (1000) and Fuse ROM (1111) modes on bits 3:0
+#define AK8963_CNTL2     0x0B  // Reset
+#define AK8963_ASTC      0x0C  // Self test control
+#define AK8963_I2CDIS    0x0F  // I2C disable
+#define AK8963_ASAX      0x10  // Fuse ROM x-axis sensitivity adjustment value
+#define AK8963_ASAY      0x11  // Fuse ROM y-axis sensitivity adjustment value
+#define AK8963_ASAZ      0x12  // Fuse ROM z-axis sensitivity adjustment value
+
+
+
+//MPU9255 register
+#define ADO 0
+#if ADO
+#define MPU9255_ADDRESS 0x69<<1  // Device address when ADO = 1
+#else
+#define MPU9255_ADDRESS 0x68<<1  // Device address when ADO = 0
+#endif
+
+#define SELF_TEST_X_GYRO 0x00                  
+#define SELF_TEST_Y_GYRO 0x01                                                                          
+#define SELF_TEST_Z_GYRO 0x02
+
+#define SELF_TEST_X_ACCEL 0x0D
+#define SELF_TEST_Y_ACCEL 0x0E    
+#define SELF_TEST_Z_ACCEL 0x0F
+
+#define SELF_TEST_A      0x10
+
+#define XG_OFFSET_H      0x13  // User-defined trim values for gyroscope
+#define XG_OFFSET_L      0x14
+#define YG_OFFSET_H      0x15
+#define YG_OFFSET_L      0x16
+#define ZG_OFFSET_H      0x17
+#define ZG_OFFSET_L      0x18
+#define SMPLRT_DIV       0x19
+#define CONFIG           0x1A
+#define GYRO_CONFIG      0x1B
+#define ACCEL_CONFIG     0x1C
+#define ACCEL_CONFIG2    0x1D
+#define LP_ACCEL_ODR     0x1E   
+#define WOM_THR          0x1F   
+
+#define MOT_DUR          0x20  // Duration counter threshold for motion interrupt generation, 1 kHz rate, LSB = 1 ms
+#define ZMOT_THR         0x21  // Zero-motion detection threshold bits [7:0]
+#define ZRMOT_DUR        0x22  // Duration counter threshold for zero motion interrupt generation, 16 Hz rate, LSB = 64 ms
+
+#define FIFO_EN          0x23
+#define I2C_MST_CTRL     0x24   
+#define I2C_SLV0_ADDR    0x25
+#define I2C_SLV0_REG     0x26
+#define I2C_SLV0_CTRL    0x27
+#define I2C_SLV1_ADDR    0x28
+#define I2C_SLV1_REG     0x29
+#define I2C_SLV1_CTRL    0x2A
+#define I2C_SLV2_ADDR    0x2B
+#define I2C_SLV2_REG     0x2C
+#define I2C_SLV2_CTRL    0x2D
+#define I2C_SLV3_ADDR    0x2E
+#define I2C_SLV3_REG     0x2F
+#define I2C_SLV3_CTRL    0x30
+#define I2C_SLV4_ADDR    0x31
+#define I2C_SLV4_REG     0x32
+#define I2C_SLV4_DO      0x33
+#define I2C_SLV4_CTRL    0x34
+#define I2C_SLV4_DI      0x35
+#define I2C_MST_STATUS   0x36
+#define INT_PIN_CFG      0x37
+#define INT_ENABLE       0x38
+#define DMP_INT_STATUS   0x39  // Check DMP interrupt
+#define INT_STATUS       0x3A
+#define ACCEL_XOUT_H     0x3B
+#define ACCEL_XOUT_L     0x3C
+#define ACCEL_YOUT_H     0x3D
+#define ACCEL_YOUT_L     0x3E
+#define ACCEL_ZOUT_H     0x3F
+#define ACCEL_ZOUT_L     0x40
+#define TEMP_OUT_H       0x41
+#define TEMP_OUT_L       0x42
+#define GYRO_XOUT_H      0x43
+#define GYRO_XOUT_L      0x44
+#define GYRO_YOUT_H      0x45
+#define GYRO_YOUT_L      0x46
+#define GYRO_ZOUT_H      0x47
+#define GYRO_ZOUT_L      0x48
+#define EXT_SENS_DATA_00 0x49
+#define EXT_SENS_DATA_01 0x4A
+#define EXT_SENS_DATA_02 0x4B
+#define EXT_SENS_DATA_03 0x4C
+#define EXT_SENS_DATA_04 0x4D
+#define EXT_SENS_DATA_05 0x4E
+#define EXT_SENS_DATA_06 0x4F
+#define EXT_SENS_DATA_07 0x50
+#define EXT_SENS_DATA_08 0x51
+#define EXT_SENS_DATA_09 0x52
+#define EXT_SENS_DATA_10 0x53
+#define EXT_SENS_DATA_11 0x54
+#define EXT_SENS_DATA_12 0x55
+#define EXT_SENS_DATA_13 0x56
+#define EXT_SENS_DATA_14 0x57
+#define EXT_SENS_DATA_15 0x58
+#define EXT_SENS_DATA_16 0x59
+#define EXT_SENS_DATA_17 0x5A
+#define EXT_SENS_DATA_18 0x5B
+#define EXT_SENS_DATA_19 0x5C
+#define EXT_SENS_DATA_20 0x5D
+#define EXT_SENS_DATA_21 0x5E
+#define EXT_SENS_DATA_22 0x5F
+#define EXT_SENS_DATA_23 0x60
+#define MOT_DETECT_STATUS 0x61
+#define I2C_SLV0_DO      0x63
+#define I2C_SLV1_DO      0x64
+#define I2C_SLV2_DO      0x65
+#define I2C_SLV3_DO      0x66
+#define I2C_MST_DELAY_CTRL 0x67
+#define SIGNAL_PATH_RESET  0x68
+#define MOT_DETECT_CTRL  0x69
+#define USER_CTRL        0x6A  // Bit 7 enable DMP, bit 3 reset DMP
+#define PWR_MGMT_1       0x6B // Device defaults to the SLEEP mode
+#define PWR_MGMT_2       0x6C
+#define DMP_BANK         0x6D  // Activates a specific bank in the DMP
+#define DMP_RW_PNT       0x6E  // Set read/write pointer to a specific start address in specified DMP bank
+#define DMP_REG          0x6F  // Register in DMP from which to read or to which to write
+#define DMP_REG_1        0x70
+#define DMP_REG_2        0x71 
+#define FIFO_COUNTH      0x72
+#define FIFO_COUNTL      0x73
+#define FIFO_R_W         0x74
+#define WHO_AM_I_MPU9255 0x75 // Should return 0x73
+#define XA_OFFSET_H      0x77
+#define XA_OFFSET_L      0x78
+#define YA_OFFSET_H      0x7A
+#define YA_OFFSET_L      0x7B
+#define ZA_OFFSET_H      0x7D
+#define ZA_OFFSET_L      0x7E
+
+#endif
\ No newline at end of file