Use this constructor if pin definitions are provided manually.

The pins that are marked NC are optional. It is assumed that these pins are not connected until/unless configured otherwise.

Destructor.

Check if the given RF is in range.

Parameters

frequency

frequency needed to be checked

Implements LoRaRadio.

Get radio status.

Parameters

status

Radio status [RF_IDLE, RF_RX_RUNNING, RF_TX_RUNNING]

Returns

Return current radio status

Implements LoRaRadio.

Registers radio events with the Mbed LoRaWAN stack and undergoes initialization steps if any.

Parameters

events

Structure containing the driver callback functions

Implements LoRaRadio.

Acquire exclusive access.

Implements LoRaRadio.

Perform carrier sensing.

Checks for a certain time if the RSSI is above a given threshold. This threshold determines if there is already a transmission going on in the channel or not.

Parameters

modem	Type of the radio modem
freq	Carrier frequency
rssi_threshold	Threshold value of RSSI
max_carrier_sense_time	time to sense the channel

Returns

true if there is no active transmission in the channel, false otherwise

Implements LoRaRadio.

Resets the radio module.

Implements LoRaRadio.

Generates a 32 bits random value based on the RSSI readings.

Remark this function sets the radio in LoRa modem mode and disables all interrupts. After calling this function either Radio.SetRxConfig or Radio.SetTxConfig functions must be called.

Returns

32 bits random value

Implements LoRaRadio.

For backwards compatibility.

Definition at line 207 of file SX1272_LoRaRadio.h.

Sets the radio to receive.

All necessary configuration options for receptions are set in 'set_rx_config(parameters)' API.

Implements LoRaRadio.

Sends the buffer of size.

Prepares the packet to be sent and sets the radio in transmission

Parameters

buffer	Buffer pointer
size	Buffer size

Implements LoRaRadio.

Sets the carrier frequency.

Parameters

freq	Channel RF frequency

Implements LoRaRadio.

Sets the maximum payload length.

Parameters

modem	Radio modem to be used [0: FSK, 1: LoRa]
max	Maximum payload length in bytes

Implements LoRaRadio.

Sets the network to public or private.

Updates the sync byte. Applies to LoRa modem only

Parameters

enable

if true, it enables a public network

Implements LoRaRadio.

Sets the reception parameters.

Parameters

modem	Radio modem to be used [0: FSK, 1: LoRa]
bandwidth	Sets the bandwidth FSK : >= 2600 and <= 250000 Hz LoRa: [0: 125 kHz, 1: 250 kHz, 2: 500 kHz, 3: Reserved]
datarate	Sets the Datarate FSK : 600..300000 bits/s LoRa: [6: 64, 7: 128, 8: 256, 9: 512, 10: 1024, 11: 2048, 12: 4096 chips]
coderate	Sets the coding rate ( LoRa only ) FSK : N/A ( set to 0 ) LoRa: [1: 4/5, 2: 4/6, 3: 4/7, 4: 4/8]
bandwidth_afc	Sets the AFC Bandwidth ( FSK only ) FSK : >= 2600 and <= 250000 Hz LoRa: N/A ( set to 0 )
preamble_len	Sets the Preamble length ( LoRa only ) FSK : N/A ( set to 0 ) LoRa: Length in symbols ( the hardware adds 4 more symbols )
symb_timeout	Sets the RxSingle timeout value FSK : timeout number of bytes LoRa: timeout in symbols
fixLen	Fixed length packets [0: variable, 1: fixed]
payload_len	Sets payload length when fixed lenght is used
crc_on	Enables/Disables the CRC [0: OFF, 1: ON]
freq_hop_on	Enables disables the intra-packet frequency hopping [0: OFF, 1: ON] (LoRa only)
hop_period	Number of symbols bewteen each hop (LoRa only)
iq_inverted	Inverts IQ signals ( LoRa only ) FSK : N/A ( set to 0 ) LoRa: [0: not inverted, 1: inverted]
rx_continuous	Sets the reception in continuous mode [false: single mode, true: continuous mode]

Implements LoRaRadio.

Sets the transmission parameters.

Parameters

modem	Radio modem to be used [0: FSK, 1: LoRa]
power	Sets the output power [dBm]
fdev	Sets the frequency deviation ( FSK only ) FSK : [Hz] LoRa: 0
bandwidth	Sets the bandwidth ( LoRa only ) FSK : 0 LoRa: [0: 125 kHz, 1: 250 kHz, 2: 500 kHz, 3: Reserved]
datarate	Sets the Datarate FSK : 600..300000 bits/s LoRa: [6: 64, 7: 128, 8: 256, 9: 512, 10: 1024, 11: 2048, 12: 4096 chips]
coderate	Sets the coding rate ( LoRa only ) FSK : N/A ( set to 0 ) LoRa: [1: 4/5, 2: 4/6, 3: 4/7, 4: 4/8]
preamble_len	Sets the preamble length
fix_len	Fixed length packets [0: variable, 1: fixed]
crc_on	Enables disables the CRC [0: OFF, 1: ON]
freq_hop_on	Enables disables the intra-packet frequency hopping [0: OFF, 1: ON] (LoRa only)
hop_period	Number of symbols bewteen each hop (LoRa only)
iq_inverted	Inverts IQ signals ( LoRa only ) FSK : N/A ( set to 0 ) LoRa: [0: not inverted, 1: inverted]
timeout	Transmission timeout [ms]

Implements LoRaRadio.

Sets the radio in continuous wave transmission mode.

Parameters

freq	Channel RF frequency
power	Sets the output power [dBm]
time	Transmission mode timeout [s]

Implements LoRaRadio.

Put the RF module in sleep mode.

Implements LoRaRadio.

Sets the radio in standby mode.

Implements LoRaRadio.

Sets the radio in CAD mode.

Implements LoRaRadio.

Computes the packet time on air for the given payload.

Remark can only be called once SetRxConfig or SetTxConfig have been called

Parameters

modem	Radio modem to be used [0: FSK, 1: LoRa]
pkt_len	Packet payload length

Returns

Computed airTime for the given packet payload length

Implements LoRaRadio.

Release exclusive access.

Implements LoRaRadio.