Mbed OS Reference | d52_starterkit.h Source File

 /**
  * This software is subject to the ANT+ Shared Source License
  * www.thisisant.com/swlicenses
  * Copyright (c) Garmin Canada Inc. 2016
  * All rights reserved.
  *
  * Redistribution and use in source and binary forms, with or
  * without modification, are permitted provided that the following
  * conditions are met:
  *
  *    1) Redistributions of source code must retain the above
  *       copyright notice, this list of conditions and the following
  *       disclaimer.
  *
  *    2) Redistributions in binary form must reproduce the above
  *       copyright notice, this list of conditions and the following
  *       disclaimer in the documentation and/or other materials
  *       provided with the distribution.
  *
  *    3) Neither the name of Garmin nor the names of its
  *       contributors may be used to endorse or promote products
  *       derived from this software without specific prior
  *       written permission.
  *
  * The following actions are prohibited:
  *
  *    1) Redistribution of source code containing the ANT+ Network
  *       Key. The ANT+ Network Key is available to ANT+ Adopters.
  *       Please refer to http://thisisant.com to become an ANT+
  *       Adopter and access the key. 
  *
  *    2) Reverse engineering, decompilation, and/or disassembly of
  *       software provided in binary form under this license.
  *
  * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND
  * CONTRIBUTORS "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES,
  * INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
  * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY
  * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR
  * CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
  * SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES(INCLUDING, 
  * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR 
  * SERVICES; DAMAGE TO ANY DEVICE, LOSS OF USE, DATA, OR 
  * PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
  * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
  * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN 
  * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED 
  * OF THE POSSIBILITY OF SUCH DAMAGE. SOME STATES DO NOT ALLOW 
  * THE EXCLUSION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE
  * ABOVE LIMITATIONS MAY NOT APPLY TO YOU.
  *
  */
 #ifndef D52STARTERKIT_H
 #define D52STARTERKIT_H
 
 #include "nrf_gpio.h"
 
 #ifdef __cplusplus
 extern "C" {
 #endif
 
 // LEDs definitions for D52DK1
 #define LEDS_NUMBER    4
 
 // IO board active low leds
 // D52DK1 does not define LED_START or LED_STOP since the LEDS are not on sequential pins
 #define LED_A        24 //LED A on D52 Starter Kit IO Board
 #define LED_B        31 //LED B on D52 Starter Kit IO Board
 #define LED_C        17 //LED C on D52 Starter Kit IO Board
 #define LED_D        20 //LED D on D52 Starter Kit IO Board
 
 #define LEDS_ACTIVE_STATE 0
 
 #define LEDS_LIST { LED_A, LED_B, LED_C, LED_D }
 
 #define BSP_LED_0      LED_A
 #define BSP_LED_1      LED_B
 #define BSP_LED_2      LED_C
 #define BSP_LED_3      LED_D
 
 #define LEDS_INV_MASK  LEDS_MASK
 
 #define BUTTONS_NUMBER 4
 
 // IO board pull-up buttons
 #define BUTTON_A     6  //BUTTON A on D52 Starter Kit IO Board
 #define BUTTON_B     7  //BUTTON B on D52 Starter Kit IO Board
 #define BUTTON_C     16 //BUTTON C on D52 Starter Kit IO Board
 #define BUTTON_D     19 //BUTTON D on D52 Starter Kit IO Board
 #define BUTTON_PULL  NRF_GPIO_PIN_PULLUP
 
 #define BUTTONS_ACTIVE_STATE 0
 
 #define BSP_BUTTON_0   BUTTON_A
 #define BSP_BUTTON_1   BUTTON_B
 #define BSP_BUTTON_2   BUTTON_C
 #define BSP_BUTTON_3   BUTTON_D
 
 #define BUTTONS_LIST { BUTTON_A, BUTTON_B, BUTTON_C, BUTTON_D }
 
 // Battery board pull-up switches
 #define SWITCH_1     12 // Switch 1 on D52 Starter Kit Battery Board
 #define SWITCH_2     8  // Switch 2 on D52 Starter Kit Battery Board
 #define SWITCH_3     15 // Switch 3 on D52 Starter Kit Battery Board
 #define SWITCH_4     11 // Switch 4 on D52 Starter Kit Battery Board
 #define SWITCH_5     14 // Switch 5 on D52 Starter Kit Battery Board
 #define SWITCH_PULL  NRF_GPIO_PIN_PULLUP
 
 #define SWITCHES_NUMBER 5
 
 #define BSP_SWITCH_0 SWITCH_1
 #define BSP_SWITCH_1 SWITCH_2
 #define BSP_SWITCH_2 SWITCH_3
 #define BSP_SWITCH_3 SWITCH_4
 #define BSP_SWITCH_4 SWITCH_5
 
 #define BSP_SWITCH_0_MASK   (1<<BSP_SWITCH_0)
 #define BSP_SWITCH_1_MASK   (1<<BSP_SWITCH_1)
 #define BSP_SWITCH_2_MASK   (1<<BSP_SWITCH_2)
 #define BSP_SWITCH_3_MASK   (1<<BSP_SWITCH_3)
 #define BSP_SWITCH_4_MASK   (1<<BSP_SWITCH_4)
 
 #define SWITCHES_MASK (BSP_SWITCH_0_MASK | BSP_SWITCH_1_MASK | BSP_SWITCH_2_MASK | BSP_SWITCH_3_MASK | BSP_SWITCH_4_MASK)
 
 // D52DK1 does not have UART peripheral. Dummy defines for compilation.
 #define RX_PIN_NUMBER  UART_PIN_DISCONNECTED
 #define TX_PIN_NUMBER  UART_PIN_DISCONNECTED
 #define CTS_PIN_NUMBER UART_PIN_DISCONNECTED
 #define RTS_PIN_NUMBER UART_PIN_DISCONNECTED
 
 // serialization CONNECTIVITY board
 #define SER_CON_RX_PIN              22    // UART RX pin number.
 #define SER_CON_TX_PIN              23    // UART TX pin number.
 #define SER_CON_CTS_PIN             25    // UART Clear To Send pin number. Not used if HWFC is set to false.
 #define SER_CON_RTS_PIN             2     // UART Request To Send pin number. Not used if HWFC is set to false.
 
 // serialization APPLICATION board - temp. setup for running serialized MEMU tests
 #define SER_APP_RX_PIN              23    // UART RX pin number.
 #define SER_APP_TX_PIN              22    // UART TX pin number.
 #define SER_APP_CTS_PIN             2     // UART Clear To Send pin number.
 #define SER_APP_RTS_PIN             25    // UART Request To Send pin number.
 
 
 #define SER_CONN_CHIP_RESET_PIN     11    // Pin used to reset connectivity chip
 
 #ifdef __cplusplus
 }
 #endif
 
 #endif
Important Information for this Arm website
