Uttam Bhat / LoRaWAN-SX1276-Application-Demo

SX1276 Shield based Applications

Dependencies:   X_NUCLEO_IKS01A1 LoRaWAN-lib SX1276Lib mbed

LoRaWAN-SX1276-Application Demo uses SX1276MB1LAS mbed component shield on a nucleo board platform to demonstrate a Class-A LoRaWAN device in the 915MHz ISM band for North American region. It uses the LoRaWAN-lib and SX1276Lib libraries.

Comissioning.h (LoRaWAN Network Configuration)

The end-device can be activated in one of the two ways:

Over the Air (OTA) activation can be enabled as shown in the figure below.

The end-device must be configured with the following parameters:

• LORAWAN_DEVICE_EUI (8 Bytes) : Fist 3 Bytes is the Organizationally Unique Identifier (OUI) followed by 5 bytes of unique ID. If not defined by user, then the firmware automatically assigns one to the end-device
• LORAWAN_APPLICATION_EUI (8 Bytes)
• LORAWAN_APPLICATION_KEY (or DEVKEY) (16 Bytes)

Activation by Personalization (ABP) can be enabled as shown in the figure below.

The end-device must be configured with the following parameters:

• LORAWAN_DEVICE_ADDRESS (4 Bytes) : If not defined by user, then the firmware automatically assigns one to the end-device
• LORAWAN_NWKSKEY (16 Bytes)
• LORAWAN_APPSKEY (16 Bytes)

Config.h (LoRaWAN Communication Parameters)

• Mode of Operation : Hybrid If the end-device needs to be configured to operate over 8-channels, then Hybrid Mode needs to be enabled

• Mode of Operation : Frequency Hop If the end-device needs to be configured to operate over 64-channels, then Hybrid Mode needs to be disabled

• Delay between successive JOIN REQUESTs : The delay between successive Join Requests (until the end-device joins the network) can be configured using the parameter OVER_THE_AIR_ACTIVATION_DUTYCYCLE

• Inter-Frame Delay : One can change the delay between each frame transmission using APP_TX_DUTYCYCLE It is advisable that APP_TX_DUTYCYCLE is greater than or equal to 3sec.

• Data Rate : The data rate can be configured as per LoRaWAN specification using the paramter LORAWAN_DEFAULT_DATARATE. The range of values are DR_0, DR_1, DR_2, DR_3 and DR_4

• Confirmed/Unconfirmed Messages : The uplink message or payload can be chosen to be confirmed or unconfirmed using the parameter LORAWAN_CONFIRMED_MSG_ON. When set to 1, the transmitted messages need to be confirmed with an ACK by the network server in the subsequent RX window. When set to 0, no ACK is requested.

• ADR ON/OFF : The ADR can be enabled or disabled using the parameter LORAWAN_ADR_ON. When set to 1, ADR is enabled and disabled when set to 0.

• Application Port : The application port can be set using parameter LORAWAN_APP_PORT. A few examples are associated to specific Application Port, and are defined in Config.h

• Payload Length : The lenght of the payload (in bytes) to be transmitted can be configured using LORAWAN_APP_DATA_SIZE

• Transmit Power : The transmit power can be configured using LORAWAN_TX_POWER (LoRaMAC verifies if the set power is compliant with the LoRaWAN spec and FCC guidelines)

The baud-rate for serial terminal display is 115200

diff -r 000000000000 -r 42863a11464a system/crypto/cmac.h
--- /dev/null	Thu Jan 01 00:00:00 1970 +0000
+++ b/system/crypto/cmac.h	Fri Aug 26 19:36:35 2016 +0000
@@ -0,0 +1,63 @@
+/**************************************************************************
+Copyright (C) 2009 Lander Casado, Philippas Tsigas
+
+All rights reserved.
+
+Permission is hereby granted, free of charge, to any person obtaining
+a copy of this software and associated documentation files 
+(the "Software"), to deal with the Software without restriction, including
+without limitation the rights to use, copy, modify, merge, publish, 
+distribute, sublicense, and/or sell copies of the Software, and to
+permit persons to whom the Software is furnished to do so, subject to
+the following conditions: 
+
+Redistributions of source code must retain the above copyright notice, 
+this list of conditions and the following disclaimers. Redistributions in
+binary form must reproduce the above copyright notice, this list of
+conditions and the following disclaimers in the documentation and/or 
+other materials provided with the distribution.
+
+In no event shall the authors or copyright holders be liable for any special,
+incidental, indirect or consequential damages of any kind, or any damages 
+whatsoever resulting from loss of use, data or profits, whether or not 
+advised of the possibility of damage, and on any theory of liability, 
+arising out of or in connection with the use or performance of this software.
+ 
+THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS
+OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
+CONTRIBUTORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
+LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING 
+FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER 
+DEALINGS WITH THE SOFTWARE
+
+*****************************************************************************/
+
+#ifndef _CMAC_H_
+#define _CMAC_H_
+
+#include "aes.h" 
+  
+#define AES_CMAC_KEY_LENGTH     16
+#define AES_CMAC_DIGEST_LENGTH  16
+ 
+typedef struct _AES_CMAC_CTX {
+            aes_context    rijndael;
+            uint8_t        X[16];
+            uint8_t        M_last[16];
+            uint32_t       M_n;
+    } AES_CMAC_CTX;
+   
+//#include <sys/cdefs.h>
+    
+//__BEGIN_DECLS
+void     AES_CMAC_Init(AES_CMAC_CTX * ctx);
+void     AES_CMAC_SetKey(AES_CMAC_CTX * ctx, const uint8_t key[AES_CMAC_KEY_LENGTH]);
+void     AES_CMAC_Update(AES_CMAC_CTX * ctx, const uint8_t * data, uint32_t len);
+          //          __attribute__((__bounded__(__string__,2,3)));
+void     AES_CMAC_Final(uint8_t digest[AES_CMAC_DIGEST_LENGTH], AES_CMAC_CTX  * ctx);
+            //     __attribute__((__bounded__(__minbytes__,1,AES_CMAC_DIGEST_LENGTH)));
+//__END_DECLS
+
+#endif /* _CMAC_H_ */
+