File content as of revision 33:8c65879e7d52:

/* mbed Microcontroller Library
 * Copyright (c) 2006-2013 ARM Limited
 *
 * Licensed under the Apache License, Version 2.0 (the "License");
 * you may not use this file except in compliance with the License.
 * You may obtain a copy of the License at
 *
 *      http://www.apache.org/licenses/LICENSE-2.0
 *
 * Unless required by applicable law or agreed to in writing, software
 * distributed under the License is distributed on an "AS IS" BASIS,
 * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
 * See the License for the specific language governing permissions and
 * limitations under the License.
 */

#include "mbed.h"
#include "BLE.h"
#include "EddystoneConfigService.h"
#include "DFUService.h"
#include "DeviceInformationService.h"
#include "ConfigParamsPersistence.h"

BLE ble;
EddystoneConfigService *EddystoneBeaconConfig;

/**
 * URIBeaconConfig service can operate in two modes: a configuration mode which
 * allows a user to update settings over a connection; and normal URIBeacon mode
 * which involves advertising a URI. Constructing an object from URIBeaconConfig
 * service sets up advertisements for the configuration mode. It is then up to
 * the application to switch to URIBeacon mode based on some timeout.
 *
 * The following help with this switch.
 */
static const int CONFIG_ADVERTISEMENT_TIMEOUT_SECONDS = 60;  // Duration after power-on that config service is available.
Ticker configAdvertisementTimeout;

/**
 * Stop advertising the Config Service after a delay; and switch to a non-connectable advertising mode only beacon.
 */
void timeout(void)
{
    Gap::GapState_t state;
    state = ble.getGapState();
    if (!state.connected) { /* don't switch if we're in a connected state. */
        EddystoneBeaconConfig->setupEddystoneAdvertisements();
        configAdvertisementTimeout.detach(); /* disable the callback from the timeout Ticker. */
        printf("removing config service\r\n");
    }
}

/**
 * Callback triggered upon a disconnection event. Needs to re-enable advertisements.
 */
void disconnectionCallback(Gap::Handle_t handle, Gap::DisconnectionReason_t reason)
{
    ble.gap().startAdvertising();
    printf("disconnect CB\r\n");
}

int main(void)
{
    printf("Starting Example\r\n");
    ble.init();
    ble.gap().onDisconnection(disconnectionCallback);

    /*
     * Load parameters from (platform specific) persistent storage. Parameters
     * can be set to non-default values while the URIBeacon is in configuration
     * mode (within the first 60 seconds of power-up). Thereafter, parameters
     * get copied out to persistent storage before switching to normal URIBeacon
     * operation.
     */
    EddystoneConfigService::Params_t params;
    bool fetchedFromPersistentStorage = loadURIBeaconConfigParams(&params);
    EddystoneConfigService::UIDNamespaceID_t uidNamespaceID = {0x00, 0x11, 0x22, 0x33, 0x44, 0x55, 0x66, 0x77, 0x88, 0x99}; // 10Byte Namespace UUID
    EddystoneConfigService::UIDInstanceID_t  uidInstanceID = {0xAA, 0xBB, 0xCC, 0xDD, 0xEE, 0xFF}; // 6Byte Instance ID
    uint8_t tlmVersion = 0x00;
    
    /* Initialize a EddystoneBeaconConfig service providing config params, default URI, and power levels. */
    static EddystoneConfigService::PowerLevels_t defaultAdvPowerLevels = {-20, -4, 0, 10}; // Values for ADV packets related to firmware levels
    EddystoneBeaconConfig = new EddystoneConfigService(ble, params, !fetchedFromPersistentStorage, "http://mbed.org", uidNamespaceID, uidInstanceID,tlmVersion, defaultAdvPowerLevels);
    if (!EddystoneBeaconConfig->configuredSuccessfully()) {
        error("failed to accommodate URI");
    }
    configAdvertisementTimeout.attach(timeout, CONFIG_ADVERTISEMENT_TIMEOUT_SECONDS);

    // Setup auxiliary services to allow over-the-air firmware updates, etc
    DFUService dfu(ble);
    DeviceInformationService deviceInfo(ble, "ARM", "UriBeacon", "SN1", "hw-rev1", "fw-rev1", "soft-rev1");

    ble.gap().startAdvertising(); /* Set the whole thing in motion. After this call a GAP central can scan the EddystoneBeaconConfig
                                   * service. This can then be switched to the normal URIBeacon functionality after a timeout. */
    printf("Running...\r\n");
    while (true) {
        ble.waitForEvent();
    }
}