Ricardo Benitez
meh
Fork of
mbed
by 
mbed official
TARGET_NUCLEO_F030R8/stm32f0xx_hal_smartcard.h
- Committer:
- Kojto
- Date:
- 2015-10-02
- Revision:
- 108:34e6b704fe68
- Parent:
- 93:e188a91d3eaa
File content as of revision 108:34e6b704fe68:
/**
******************************************************************************
* @file stm32f0xx_hal_smartcard.h
* @author MCD Application Team
* @version V1.3.0
* @date 26-June-2015
* @brief Header file of SMARTCARD HAL module.
******************************************************************************
* @attention
*
* <h2><center>© COPYRIGHT(c) 2015 STMicroelectronics</center></h2>
*
* Redistribution and use in source and binary forms, with or without modification,
* are permitted provided that the following conditions are met:
* 1. Redistributions of source code must retain the above copyright notice,
* this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright notice,
* this list of conditions and the following disclaimer in the documentation
* and/or other materials provided with the distribution.
* 3. Neither the name of STMicroelectronics nor the names of its contributors
* may be used to endorse or promote products derived from this software
* without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
* AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
* DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
* FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
* SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
* CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
* OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
* OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*
******************************************************************************
*/
/* Define to prevent recursive inclusion -------------------------------------*/
#ifndef __STM32F0xx_HAL_SMARTCARD_H
#define __STM32F0xx_HAL_SMARTCARD_H
#ifdef __cplusplus
extern "C" {
#endif
#if !defined(STM32F030x6) && !defined(STM32F030x8) && !defined(STM32F070x6) && !defined(STM32F070xB) && !defined(STM32F030xC)
/* Includes ------------------------------------------------------------------*/
#include "stm32f0xx_hal_def.h"
/** @addtogroup STM32F0xx_HAL_Driver
* @{
*/
/** @addtogroup SMARTCARD
* @{
*/
/* Exported types ------------------------------------------------------------*/
/** @defgroup SMARTCARD_Exported_Types SMARTCARD Exported Types
* @{
*/
/**
* @brief SMARTCARD Init Structure definition
*/
typedef struct
{
uint32_t BaudRate; /*!< Configures the SmartCard communication baud rate.
The baud rate register is computed using the following formula:
Baud Rate Register = ((PCLKx) / ((hsmartcard->Init.BaudRate))) */
uint32_t WordLength; /*!< Specifies the number of data bits transmitted or received in a frame.
This parameter @ref SMARTCARD_Word_Length can only be set to 9 (8 data + 1 parity bits). */
uint32_t StopBits; /*!< Specifies the number of stop bits @ref SMARTCARD_Stop_Bits.
Only 1.5 stop bits are authorized in SmartCard mode. */
uint16_t Parity; /*!< Specifies the parity mode.
This parameter can be a value of @ref SMARTCARD_Parity
@note The parity is enabled by default (PCE is forced to 1).
Since the WordLength is forced to 8 bits + parity, M is
forced to 1 and the parity bit is the 9th bit. */
uint16_t Mode; /*!< Specifies whether the Receive or Transmit mode is enabled or disabled.
This parameter can be a value of @ref SMARTCARD_Mode */
uint16_t CLKPolarity; /*!< Specifies the steady state of the serial clock.
This parameter can be a value of @ref SMARTCARD_Clock_Polarity */
uint16_t CLKPhase; /*!< Specifies the clock transition on which the bit capture is made.
This parameter can be a value of @ref SMARTCARD_Clock_Phase */
uint16_t CLKLastBit; /*!< Specifies whether the clock pulse corresponding to the last transmitted
data bit (MSB) has to be output on the SCLK pin in synchronous mode.
This parameter can be a value of @ref SMARTCARD_Last_Bit */
uint16_t OneBitSampling; /*!< Specifies whether a single sample or three samples' majority vote is selected.
Selecting the single sample method increases the receiver tolerance to clock
deviations. This parameter can be a value of @ref SMARTCARD_OneBit_Sampling. */
uint8_t Prescaler; /*!< Specifies the SmartCard Prescaler */
uint8_t GuardTime; /*!< Specifies the SmartCard Guard Time */
uint16_t NACKEnable; /*!< Specifies whether the SmartCard NACK transmission is enabled
in case of parity error.
This parameter can be a value of @ref SMARTCARD_NACK_Enable */
uint32_t TimeOutEnable; /*!< Specifies whether the receiver timeout is enabled.
This parameter can be a value of @ref SMARTCARD_Timeout_Enable*/
uint32_t TimeOutValue; /*!< Specifies the receiver time out value in number of baud blocks:
it is used to implement the Character Wait Time (CWT) and
Block Wait Time (BWT). It is coded over 24 bits. */
uint8_t BlockLength; /*!< Specifies the SmartCard Block Length in T=1 Reception mode.
This parameter can be any value from 0x0 to 0xFF */
uint8_t AutoRetryCount; /*!< Specifies the SmartCard auto-retry count (number of retries in
receive and transmit mode). When set to 0, retransmission is
disabled. Otherwise, its maximum value is 7 (before signalling
an error) */
}SMARTCARD_InitTypeDef;
/**
* @brief SMARTCARD advanced features initalization structure definition
*/
typedef struct
{
uint32_t AdvFeatureInit; /*!< Specifies which advanced SMARTCARD features is initialized. Several
advanced features may be initialized at the same time. This parameter
can be a value of @ref SMARTCARD_Advanced_Features_Initialization_Type */
uint32_t TxPinLevelInvert; /*!< Specifies whether the TX pin active level is inverted.
This parameter can be a value of @ref SMARTCARD_Tx_Inv */
uint32_t RxPinLevelInvert; /*!< Specifies whether the RX pin active level is inverted.
This parameter can be a value of @ref SMARTCARD_Rx_Inv */
uint32_t DataInvert; /*!< Specifies whether data are inverted (positive/direct logic
vs negative/inverted logic).
This parameter can be a value of @ref SMARTCARD_Data_Inv */
uint32_t Swap; /*!< Specifies whether TX and RX pins are swapped.
This parameter can be a value of @ref SMARTCARD_Rx_Tx_Swap */
uint32_t OverrunDisable; /*!< Specifies whether the reception overrun detection is disabled.
This parameter can be a value of @ref SMARTCARD_Overrun_Disable */
uint32_t DMADisableonRxError; /*!< Specifies whether the DMA is disabled in case of reception error.
This parameter can be a value of @ref SMARTCARD_DMA_Disable_on_Rx_Error */
uint32_t MSBFirst; /*!< Specifies whether MSB is sent first on UART line.
This parameter can be a value of @ref SMARTCARD_MSB_First */
}SMARTCARD_AdvFeatureInitTypeDef;
/**
* @brief HAL State structures definition
*/
typedef enum
{
HAL_SMARTCARD_STATE_RESET = 0x00, /*!< Peripheral is not initialized */
HAL_SMARTCARD_STATE_READY = 0x01, /*!< Peripheral Initialized and ready for use */
HAL_SMARTCARD_STATE_BUSY = 0x02, /*!< an internal process is ongoing */
HAL_SMARTCARD_STATE_BUSY_TX = 0x12, /*!< Data Transmission process is ongoing */
HAL_SMARTCARD_STATE_BUSY_RX = 0x22, /*!< Data Reception process is ongoing */
HAL_SMARTCARD_STATE_BUSY_TX_RX = 0x32, /*!< Data Transmission and Reception process is ongoing */
HAL_SMARTCARD_STATE_TIMEOUT = 0x03, /*!< Timeout state */
HAL_SMARTCARD_STATE_ERROR = 0x04 /*!< Error */
}HAL_SMARTCARD_StateTypeDef;
/**
* @brief SMARTCARD clock sources
*/
typedef enum
{
SMARTCARD_CLOCKSOURCE_PCLK1 = 0x00, /*!< PCLK1 clock source */
SMARTCARD_CLOCKSOURCE_HSI = 0x02, /*!< HSI clock source */
SMARTCARD_CLOCKSOURCE_SYSCLK = 0x04, /*!< SYSCLK clock source */
SMARTCARD_CLOCKSOURCE_LSE = 0x08, /*!< LSE clock source */
SMARTCARD_CLOCKSOURCE_UNDEFINED = 0x10 /*!< undefined clock source */
}SMARTCARD_ClockSourceTypeDef;
/**
* @brief SMARTCARD handle Structure definition
*/
typedef struct
{
USART_TypeDef *Instance; /*!< USART registers base address */
SMARTCARD_InitTypeDef Init; /*!< SmartCard communication parameters */
SMARTCARD_AdvFeatureInitTypeDef AdvancedInit; /*!< SmartCard advanced features initialization parameters */
uint8_t *pTxBuffPtr; /*!< Pointer to SmartCard Tx transfer Buffer */
uint16_t TxXferSize; /*!< SmartCard Tx Transfer size */
uint16_t TxXferCount; /*!< SmartCard Tx Transfer Counter */
uint8_t *pRxBuffPtr; /*!< Pointer to SmartCard Rx transfer Buffer */
uint16_t RxXferSize; /*!< SmartCard Rx Transfer size */
uint16_t RxXferCount; /*!< SmartCard Rx Transfer Counter */
DMA_HandleTypeDef *hdmatx; /*!< SmartCard Tx DMA Handle parameters */
DMA_HandleTypeDef *hdmarx; /*!< SmartCard Rx DMA Handle parameters */
HAL_LockTypeDef Lock; /*!< Locking object */
__IO HAL_SMARTCARD_StateTypeDef State; /*!< SmartCard communication state */
__IO uint32_t ErrorCode; /*!< SmartCard Error code
This parameter can be a value of @ref SMARTCARD_Error */
}SMARTCARD_HandleTypeDef;
/**
* @}
*/
/* Exported constants --------------------------------------------------------*/
/** @defgroup SMARTCARD_Exported_Constants SMARTCARD Exported Constants
* @{
*/
/** @defgroup SMARTCARD_Error SMARTCARD Error
* @{
*/
#define HAL_SMARTCARD_ERROR_NONE ((uint32_t)0x00000000) /*!< No error */
#define HAL_SMARTCARD_ERROR_PE ((uint32_t)0x00000001) /*!< Parity error */
#define HAL_SMARTCARD_ERROR_NE ((uint32_t)0x00000002) /*!< Noise error */
#define HAL_SMARTCARD_ERROR_FE ((uint32_t)0x00000004) /*!< frame error */
#define HAL_SMARTCARD_ERROR_ORE ((uint32_t)0x00000008) /*!< Overrun error */
#define HAL_SMARTCARD_ERROR_DMA ((uint32_t)0x00000010) /*!< DMA transfer error */
#define HAL_SMARTCARD_ERROR_RTO ((uint32_t)0x00000020) /*!< Receiver TimeOut error */
/**
* @}
*/
/** @defgroup SMARTCARD_Word_Length SMARTCARD Word Length
* @{
*/
#define SMARTCARD_WORDLENGTH_9B ((uint32_t)USART_CR1_M0) /*!< SMARTCARD frame length */
/**
* @}
*/
/** @defgroup SMARTCARD_Stop_Bits SMARTCARD Stop Bits
* @{
*/
#define SMARTCARD_STOPBITS_1_5 USART_CR2_STOP /*!< SMARTCARD frame with 1.5 stop bits */
/**
* @}
*/
/** @defgroup SMARTCARD_Parity SMARTCARD Parity
* @{
*/
#define SMARTCARD_PARITY_EVEN ((uint32_t)USART_CR1_PCE) /*!< SMARTCARD frame even parity */
#define SMARTCARD_PARITY_ODD ((uint32_t)(USART_CR1_PCE | USART_CR1_PS)) /*!< SMARTCARD frame odd parity */
/**
* @}
*/
/** @defgroup SMARTCARD_Mode SMARTCARD Transfer Mode
* @{
*/
#define SMARTCARD_MODE_RX ((uint32_t)USART_CR1_RE) /*!< SMARTCARD RX mode */
#define SMARTCARD_MODE_TX ((uint32_t)USART_CR1_TE) /*!< SMARTCARD TX mode */
#define SMARTCARD_MODE_TX_RX ((uint32_t)(USART_CR1_TE |USART_CR1_RE)) /*!< SMARTCARD RX and TX mode */
/**
* @}
*/
/** @defgroup SMARTCARD_Clock_Polarity SMARTCARD Clock Polarity
* @{
*/
#define SMARTCARD_POLARITY_LOW ((uint32_t)0x00000000) /*!< SMARTCARD frame low polarity */
#define SMARTCARD_POLARITY_HIGH ((uint32_t)USART_CR2_CPOL) /*!< SMARTCARD frame high polarity */
/**
* @}
*/
/** @defgroup SMARTCARD_Clock_Phase SMARTCARD Clock Phase
* @{
*/
#define SMARTCARD_PHASE_1EDGE ((uint32_t)0x00000000) /*!< SMARTCARD frame phase on first clock transition */
#define SMARTCARD_PHASE_2EDGE ((uint32_t)USART_CR2_CPHA) /*!< SMARTCARD frame phase on second clock transition */
/**
* @}
*/
/** @defgroup SMARTCARD_Last_Bit SMARTCARD Last Bit
* @{
*/
#define SMARTCARD_LASTBIT_DISABLE ((uint32_t)0x00000000) /*!< SMARTCARD frame last data bit clock pulse not output to SCLK pin */
#define SMARTCARD_LASTBIT_ENABLE ((uint32_t)USART_CR2_LBCL) /*!< SMARTCARD frame last data bit clock pulse output to SCLK pin */
/**
* @}
*/
/** @defgroup SMARTCARD_OneBit_Sampling SMARTCARD One Bit Sampling Method
* @{
*/
#define SMARTCARD_ONE_BIT_SAMPLE_DISABLE ((uint32_t)0x00000000) /*!< SMARTCARD frame one-bit sample disabled */
#define SMARTCARD_ONE_BIT_SAMPLE_ENABLE ((uint32_t)USART_CR3_ONEBIT) /*!< SMARTCARD frame one-bit sample enabled */
/**
* @}
*/
/** @defgroup SMARTCARD_NACK_Enable SMARTCARD NACK Enable
* @{
*/
#define SMARTCARD_NACK_ENABLE ((uint32_t)USART_CR3_NACK) /*!< SMARTCARD NACK transmission disabled */
#define SMARTCARD_NACK_DISABLE ((uint32_t)0x00000000) /*!< SMARTCARD NACK transmission enabled */
/**
* @}
*/
/** @defgroup SMARTCARD_Timeout_Enable SMARTCARD Timeout Enable
* @{
*/
#define SMARTCARD_TIMEOUT_DISABLE ((uint32_t)0x00000000) /*!< SMARTCARD receiver timeout disabled */
#define SMARTCARD_TIMEOUT_ENABLE ((uint32_t)USART_CR2_RTOEN) /*!< SMARTCARD receiver timeout enabled */
/**
* @}
*/
/** @defgroup SMARTCARD_Advanced_Features_Initialization_Type SMARTCARD advanced feature initialization type
* @{
*/
#define SMARTCARD_ADVFEATURE_NO_INIT ((uint32_t)0x00000000) /*!< No advanced feature initialization */
#define SMARTCARD_ADVFEATURE_TXINVERT_INIT ((uint32_t)0x00000001) /*!< TX pin active level inversion */
#define SMARTCARD_ADVFEATURE_RXINVERT_INIT ((uint32_t)0x00000002) /*!< RX pin active level inversion */
#define SMARTCARD_ADVFEATURE_DATAINVERT_INIT ((uint32_t)0x00000004) /*!< Binary data inversion */
#define SMARTCARD_ADVFEATURE_SWAP_INIT ((uint32_t)0x00000008) /*!< TX/RX pins swap */
#define SMARTCARD_ADVFEATURE_RXOVERRUNDISABLE_INIT ((uint32_t)0x00000010) /*!< RX overrun disable */
#define SMARTCARD_ADVFEATURE_DMADISABLEONERROR_INIT ((uint32_t)0x00000020) /*!< DMA disable on Reception Error */
#define SMARTCARD_ADVFEATURE_MSBFIRST_INIT ((uint32_t)0x00000080) /*!< Most significant bit sent/received first */
/**
* @}
*/
/** @defgroup SMARTCARD_Tx_Inv SMARTCARD advanced feature TX pin active level inversion
* @{
*/
#define SMARTCARD_ADVFEATURE_TXINV_DISABLE ((uint32_t)0x00000000) /*!< TX pin active level inversion disable */
#define SMARTCARD_ADVFEATURE_TXINV_ENABLE ((uint32_t)USART_CR2_TXINV) /*!< TX pin active level inversion enable */
/**
* @}
*/
/** @defgroup SMARTCARD_Rx_Inv SMARTCARD advanced feature RX pin active level inversion
* @{
*/
#define SMARTCARD_ADVFEATURE_RXINV_DISABLE ((uint32_t)0x00000000) /*!< RX pin active level inversion disable */
#define SMARTCARD_ADVFEATURE_RXINV_ENABLE ((uint32_t)USART_CR2_RXINV) /*!< RX pin active level inversion enable */
/**
* @}
*/
/** @defgroup SMARTCARD_Data_Inv SMARTCARD advanced feature Binary Data inversion
* @{
*/
#define SMARTCARD_ADVFEATURE_DATAINV_DISABLE ((uint32_t)0x00000000) /*!< Binary data inversion disable */
#define SMARTCARD_ADVFEATURE_DATAINV_ENABLE ((uint32_t)USART_CR2_DATAINV) /*!< Binary data inversion enable */
/**
* @}
*/
/** @defgroup SMARTCARD_Rx_Tx_Swap SMARTCARD advanced feature RX TX pins swap
* @{
*/
#define SMARTCARD_ADVFEATURE_SWAP_DISABLE ((uint32_t)0x00000000) /*!< TX/RX pins swap disable */
#define SMARTCARD_ADVFEATURE_SWAP_ENABLE ((uint32_t)USART_CR2_SWAP) /*!< TX/RX pins swap enable */
/**
* @}
*/
/** @defgroup SMARTCARD_Overrun_Disable SMARTCARD advanced feature Overrun Disable
* @{
*/
#define SMARTCARD_ADVFEATURE_OVERRUN_ENABLE ((uint32_t)0x00000000) /*!< RX overrun enable */
#define SMARTCARD_ADVFEATURE_OVERRUN_DISABLE ((uint32_t)USART_CR3_OVRDIS) /*!< RX overrun disable */
/**
* @}
*/
/** @defgroup SMARTCARD_DMA_Disable_on_Rx_Error SMARTCARD advanced feature DMA Disable on Rx Error
* @{
*/
#define SMARTCARD_ADVFEATURE_DMA_ENABLEONRXERROR ((uint32_t)0x00000000) /*!< DMA enable on Reception Error */
#define SMARTCARD_ADVFEATURE_DMA_DISABLEONRXERROR ((uint32_t)USART_CR3_DDRE) /*!< DMA disable on Reception Error */
/**
* @}
*/
/** @defgroup SMARTCARD_MSB_First SMARTCARD advanced feature MSB first
* @{
*/
#define SMARTCARD_ADVFEATURE_MSBFIRST_DISABLE ((uint32_t)0x00000000) /*!< Most significant bit sent/received first disable */
#define SMARTCARD_ADVFEATURE_MSBFIRST_ENABLE ((uint32_t)USART_CR2_MSBFIRST) /*!< Most significant bit sent/received first enable */
/**
* @}
*/
/** @defgroup SMARTCARD_Flags SMARTCARD Flags
* Elements values convention: 0xXXXX
* - 0xXXXX : Flag mask in the ISR register
* @{
*/
#define SMARTCARD_FLAG_REACK USART_ISR_REACK /*!< SMARTCARD receive enable acknowledge flag */
#define SMARTCARD_FLAG_TEACK USART_ISR_TEACK /*!< SMARTCARD transmit enable acknowledge flag */
#define SMARTCARD_FLAG_BUSY USART_ISR_BUSY /*!< SMARTCARD busy flag */
#define SMARTCARD_FLAG_EOBF USART_ISR_EOBF /*!< SMARTCARD end of block flag */
#define SMARTCARD_FLAG_RTOF USART_ISR_RTOF /*!< SMARTCARD receiver timeout flag */
#define SMARTCARD_FLAG_TXE USART_ISR_TXE /*!< SMARTCARD transmit data register empty */
#define SMARTCARD_FLAG_TC USART_ISR_TC /*!< SMARTCARD transmission complete */
#define SMARTCARD_FLAG_RXNE USART_ISR_RXNE /*!< SMARTCARD read data register not empty */
#define SMARTCARD_FLAG_IDLE USART_ISR_IDLE /*!< SMARTCARD idle line detection */
#define SMARTCARD_FLAG_ORE USART_ISR_ORE /*!< SMARTCARD overrun error */
#define SMARTCARD_FLAG_NE USART_ISR_NE /*!< SMARTCARD noise error */
#define SMARTCARD_FLAG_FE USART_ISR_FE /*!< SMARTCARD frame error */
#define SMARTCARD_FLAG_PE USART_ISR_PE /*!< SMARTCARD parity error */
/**
* @}
*/
/** @defgroup SMARTCARD_Interrupt_definition SMARTCARD Interrupts Definition
* Elements values convention: 0000ZZZZ0XXYYYYYb
* - YYYYY : Interrupt source position in the XX register (5bits)
* - XX : Interrupt source register (2bits)
* - 01: CR1 register
* - 10: CR2 register
* - 11: CR3 register
* - ZZZZ : Flag position in the ISR register(4bits)
* @{
*/
#define SMARTCARD_IT_PE ((uint16_t)0x0028) /*!< SMARTCARD parity error interruption */
#define SMARTCARD_IT_TXE ((uint16_t)0x0727) /*!< SMARTCARD transmit data register empty interruption */
#define SMARTCARD_IT_TC ((uint16_t)0x0626) /*!< SMARTCARD transmission complete interruption */
#define SMARTCARD_IT_RXNE ((uint16_t)0x0525) /*!< SMARTCARD read data register not empty interruption */
#define SMARTCARD_IT_IDLE ((uint16_t)0x0424) /*!< SMARTCARD idle line detection interruption */
#define SMARTCARD_IT_ERR ((uint16_t)0x0060) /*!< SMARTCARD error interruption */
#define SMARTCARD_IT_ORE ((uint16_t)0x0300) /*!< SMARTCARD overrun error interruption */
#define SMARTCARD_IT_NE ((uint16_t)0x0200) /*!< SMARTCARD noise error interruption */
#define SMARTCARD_IT_FE ((uint16_t)0x0100) /*!< SMARTCARD frame error interruption */
#define SMARTCARD_IT_EOB ((uint16_t)0x0C3B) /*!< SMARTCARD end of block interruption */
#define SMARTCARD_IT_RTO ((uint16_t)0x0B3A) /*!< SMARTCARD receiver timeout interruption */
/**
* @}
*/
/** @defgroup SMARTCARD_IT_CLEAR_Flags SMARTCARD Interruption Clear Flags
* @{
*/
#define SMARTCARD_CLEAR_PEF USART_ICR_PECF /*!< SMARTCARD parity error clear flag */
#define SMARTCARD_CLEAR_FEF USART_ICR_FECF /*!< SMARTCARD framing error clear flag */
#define SMARTCARD_CLEAR_NEF USART_ICR_NCF /*!< SMARTCARD noise detected clear flag */
#define SMARTCARD_CLEAR_OREF USART_ICR_ORECF /*!< SMARTCARD overrun error clear flag */
#define SMARTCARD_CLEAR_IDLEF USART_ICR_IDLECF /*!< SMARTCARD idle line detected clear flag */
#define SMARTCARD_CLEAR_TCF USART_ICR_TCCF /*!< SMARTCARD transmission complete clear flag */
#define SMARTCARD_CLEAR_RTOF USART_ICR_RTOCF /*!< SMARTCARD receiver time out clear flag */
#define SMARTCARD_CLEAR_EOBF USART_ICR_EOBCF /*!< SMARTCARD end of block clear flag */
/**
* @}
*/
/** @defgroup SMARTCARD_CR3_SCARCNT_LSB_POS SMARTCARD auto retry counter LSB position in CR3 register
* @{
*/
#define SMARTCARD_CR3_SCARCNT_LSB_POS ((uint32_t) 17) /*!< SMARTCARD auto retry counter LSB position in CR3 register */
/**
* @}
*/
/** @defgroup SMARTCARD_GTPR_GT_LSB_POS SMARTCARD guard time value LSB position in GTPR register
* @{
*/
#define SMARTCARD_GTPR_GT_LSB_POS ((uint32_t) 8) /*!< SMARTCARD guard time value LSB position in GTPR register */
/**
* @}
*/
/** @defgroup SMARTCARD_RTOR_BLEN_LSB_POS SMARTCARD block length LSB position in RTOR register
* @{
*/
#define SMARTCARD_RTOR_BLEN_LSB_POS ((uint32_t) 24) /*!< SMARTCARD block length LSB position in RTOR register */
/**
* @}
*/
/** @defgroup SMARTCARD_Interruption_Mask SMARTCARD interruptions flags mask
* @{
*/
#define SMARTCARD_IT_MASK ((uint16_t)0x001F) /*!< SMARTCARD interruptions flags mask */
/**
* @}
*/
/** @defgroup SMARTCARD_Request_Parameters SMARTCARD Request Parameters
* @{
*/
#define SMARTCARD_RXDATA_FLUSH_REQUEST ((uint16_t)USART_RQR_RXFRQ) /*!< Receive Data flush Request */
#define SMARTCARD_TXDATA_FLUSH_REQUEST ((uint16_t)USART_RQR_TXFRQ) /*!< Transmit data flush Request */
/**
* @}
*/
/**
* @}
*/
/* Exported macros -----------------------------------------------------------*/
/** @defgroup SMARTCARD_Exported_Macros SMARTCARD Exported Macros
* @{
*/
/** @brief Reset SMARTCARD handle state.
* @param __HANDLE__: SMARTCARD handle.
* @retval None
*/
#define __HAL_SMARTCARD_RESET_HANDLE_STATE(__HANDLE__) ((__HANDLE__)->State = HAL_SMARTCARD_STATE_RESET)
/** @brief Flush the Smartcard Data registers.
* @param __HANDLE__: specifies the SMARTCARD Handle.
* @retval None
*/
#define __HAL_SMARTCARD_FLUSH_DRREGISTER(__HANDLE__) \
do{ \
SET_BIT((__HANDLE__)->Instance->RQR, SMARTCARD_RXDATA_FLUSH_REQUEST); \
SET_BIT((__HANDLE__)->Instance->RQR, SMARTCARD_TXDATA_FLUSH_REQUEST); \
} while(0)
/** @brief Clear the specified SMARTCARD pending flag.
* @param __HANDLE__: specifies the SMARTCARD Handle.
* @param __FLAG__: specifies the flag to check.
* This parameter can be any combination of the following values:
* @arg SMARTCARD_CLEAR_PEF: Parity error clear flag
* @arg SMARTCARD_CLEAR_FEF: Framing error clear flag
* @arg SMARTCARD_CLEAR_NEF: Noise detected clear flag
* @arg SMARTCARD_CLEAR_OREF: OverRun error clear flag
* @arg SMARTCARD_CLEAR_IDLEF: Idle line detected clear flag
* @arg SMARTCARD_CLEAR_TCF: Transmission complete clear flag
* @arg SMARTCARD_CLEAR_RTOF: Receiver timeout clear flag
* @arg SMARTCARD_CLEAR_EOBF: End of block clear flag
* @retval None
*/
#define __HAL_SMARTCARD_CLEAR_FLAG(__HANDLE__, __FLAG__) ((__HANDLE__)->Instance->ICR = (__FLAG__))
/** @brief Clear the SMARTCARD PE pending flag.
* @param __HANDLE__: specifies the SMARTCARD Handle.
* @retval None
*/
#define __HAL_SMARTCARD_CLEAR_PEFLAG(__HANDLE__) __HAL_SMARTCARD_CLEAR_FLAG((__HANDLE__), SMARTCARD_CLEAR_PEF)
/** @brief Clear the SMARTCARD FE pending flag.
* @param __HANDLE__: specifies the SMARTCARD Handle.
* @retval None
*/
#define __HAL_SMARTCARD_CLEAR_FEFLAG(__HANDLE__) __HAL_SMARTCARD_CLEAR_FLAG((__HANDLE__), SMARTCARD_CLEAR_FEF)
/** @brief Clear the SMARTCARD NE pending flag.
* @param __HANDLE__: specifies the SMARTCARD Handle.
* @retval None
*/
#define __HAL_SMARTCARD_CLEAR_NEFLAG(__HANDLE__) __HAL_SMARTCARD_CLEAR_FLAG((__HANDLE__), SMARTCARD_CLEAR_NEF)
/** @brief Clear the SMARTCARD ORE pending flag.
* @param __HANDLE__: specifies the SMARTCARD Handle.
* @retval None
*/
#define __HAL_SMARTCARD_CLEAR_OREFLAG(__HANDLE__) __HAL_SMARTCARD_CLEAR_FLAG((__HANDLE__), SMARTCARD_CLEAR_OREF)
/** @brief Clear the SMARTCARD IDLE pending flag.
* @param __HANDLE__: specifies the SMARTCARD Handle.
* @retval None
*/
#define __HAL_SMARTCARD_CLEAR_IDLEFLAG(__HANDLE__) __HAL_SMARTCARD_CLEAR_FLAG((__HANDLE__), SMARTCARD_CLEAR_IDLEF)
/** @brief Check whether the specified Smartcard flag is set or not.
* @param __HANDLE__: specifies the SMARTCARD Handle.
* The Handle Instance can be USARTx where x: 1, 2 or 3 to select the USART peripheral.
* @param __FLAG__: specifies the flag to check.
* This parameter can be one of the following values:
* @arg SMARTCARD_FLAG_REACK: Receive enable acknowledge flag
* @arg SMARTCARD_FLAG_TEACK: Transmit enable acknowledge flag
* @arg SMARTCARD_FLAG_BUSY: Busy flag
* @arg SMARTCARD_FLAG_EOBF: End of block flag
* @arg SMARTCARD_FLAG_RTOF: Receiver timeout flag
* @arg SMARTCARD_FLAG_TXE: Transmit data register empty flag
* @arg SMARTCARD_FLAG_TC: Transmission complete flag
* @arg SMARTCARD_FLAG_RXNE: Receive data register not empty flag
* @arg SMARTCARD_FLAG_IDLE: Idle line detection flag
* @arg SMARTCARD_FLAG_ORE: Overrun error flag
* @arg SMARTCARD_FLAG_NE: Noise error flag
* @arg SMARTCARD_FLAG_FE: Framing error flag
* @arg SMARTCARD_FLAG_PE: Parity error flag
* @retval The new state of __FLAG__ (TRUE or FALSE).
*/
#define __HAL_SMARTCARD_GET_FLAG(__HANDLE__, __FLAG__) (((__HANDLE__)->Instance->ISR & (__FLAG__)) == (__FLAG__))
/** @brief Enable the specified SmartCard interrupt.
* @param __HANDLE__: specifies the SMARTCARD Handle.
* The Handle Instance can be USARTx where x: 1, 2 or 3 to select the USART peripheral.
* @param __INTERRUPT__: specifies the SMARTCARD interrupt to enable.
* This parameter can be one of the following values:
* @arg SMARTCARD_IT_EOB: End of block interrupt
* @arg SMARTCARD_IT_RTO: Receive timeout interrupt
* @arg SMARTCARD_IT_TXE: Transmit data register empty interrupt
* @arg SMARTCARD_IT_TC: Transmission complete interrupt
* @arg SMARTCARD_IT_RXNE: Receive data register not empty interrupt
* @arg SMARTCARD_IT_IDLE: Idle line detection interrupt
* @arg SMARTCARD_IT_PE: Parity error interrupt
* @arg SMARTCARD_IT_ERR: Error interrupt(frame error, noise error, overrun error)
* @retval None
*/
#define __HAL_SMARTCARD_ENABLE_IT(__HANDLE__, __INTERRUPT__) (((((uint8_t)(__INTERRUPT__)) >> 5U) == 1)? ((__HANDLE__)->Instance->CR1 |= (1U << ((__INTERRUPT__) & SMARTCARD_IT_MASK))): \
((((uint8_t)(__INTERRUPT__)) >> 5U) == 2)? ((__HANDLE__)->Instance->CR2 |= (1U << ((__INTERRUPT__) & SMARTCARD_IT_MASK))): \
((__HANDLE__)->Instance->CR3 |= (1U << ((__INTERRUPT__) & SMARTCARD_IT_MASK))))
/** @brief Disable the specified SmartCard interrupt.
* @param __HANDLE__: specifies the SMARTCARD Handle.
* The Handle Instance can be USARTx where x: 1, 2 or 3 to select the USART peripheral.
* @param __INTERRUPT__: specifies the SMARTCARD interrupt to disable.
* This parameter can be one of the following values:
* @arg SMARTCARD_IT_EOB: End of block interrupt
* @arg SMARTCARD_IT_RTO: Receive timeout interrupt
* @arg SMARTCARD_IT_TXE: Transmit data register empty interrupt
* @arg SMARTCARD_IT_TC: Transmission complete interrupt
* @arg SMARTCARD_IT_RXNE: Receive data register not empty interrupt
* @arg SMARTCARD_IT_IDLE: Idle line detection interrupt
* @arg SMARTCARD_IT_PE: Parity error interrupt
* @arg SMARTCARD_IT_ERR: Error interrupt(frame error, noise error, overrun error)
* @retval None
*/
#define __HAL_SMARTCARD_DISABLE_IT(__HANDLE__, __INTERRUPT__) (((((uint8_t)(__INTERRUPT__)) >> 5U) == 1)? ((__HANDLE__)->Instance->CR1 &= ~ (1U << ((__INTERRUPT__) & SMARTCARD_IT_MASK))): \
((((uint8_t)(__INTERRUPT__)) >> 5U) == 2)? ((__HANDLE__)->Instance->CR2 &= ~ (1U << ((__INTERRUPT__) & SMARTCARD_IT_MASK))): \
((__HANDLE__)->Instance->CR3 &= ~ (1U << ((__INTERRUPT__) & SMARTCARD_IT_MASK))))
/** @brief Check whether the specified SmartCard interrupt has occurred or not.
* @param __HANDLE__: specifies the SMARTCARD Handle.
* The Handle Instance can be USARTx where x: 1, 2 or 3 to select the USART peripheral.
* @param __IT__: specifies the SMARTCARD interrupt to check.
* This parameter can be one of the following values:
* @arg SMARTCARD_IT_EOB: End of block interrupt
* @arg SMARTCARD_IT_RTO: Receive timeout interrupt
* @arg SMARTCARD_IT_TXE: Transmit data register empty interrupt
* @arg SMARTCARD_IT_TC: Transmission complete interrupt
* @arg SMARTCARD_IT_RXNE: Receive data register not empty interrupt
* @arg SMARTCARD_IT_IDLE: Idle line detection interrupt
* @arg SMARTCARD_IT_ORE: Overrun error interrupt
* @arg SMARTCARD_IT_NE: Noise error interrupt
* @arg SMARTCARD_IT_FE: Framing error interrupt
* @arg SMARTCARD_IT_PE: Parity error interrupt
* @retval The new state of __IT__ (TRUE or FALSE).
*/
#define __HAL_SMARTCARD_GET_IT(__HANDLE__, __IT__) ((__HANDLE__)->Instance->ISR & ((uint32_t)1 << ((__IT__)>> 0x08)))
/** @brief Check whether the specified SmartCard interrupt source is enabled or not.
* @param __HANDLE__: specifies the SMARTCARD Handle.
* The Handle Instance can be USARTx where x: 1, 2 or 3 to select the USART peripheral.
* @param __IT__: specifies the SMARTCARD interrupt source to check.
* This parameter can be one of the following values:
* @arg SMARTCARD_IT_EOB: End of block interrupt
* @arg SMARTCARD_IT_RTO: Receive timeout interrupt
* @arg SMARTCARD_IT_TXE: Transmit data register empty interrupt
* @arg SMARTCARD_IT_TC: Transmission complete interrupt
* @arg SMARTCARD_IT_RXNE: Receive data register not empty interrupt
* @arg SMARTCARD_IT_IDLE: Idle line detection interrupt
* @arg SMARTCARD_IT_ORE: Overrun error interrupt
* @arg SMARTCARD_IT_NE: Noise error interrupt
* @arg SMARTCARD_IT_FE: Framing error interrupt
* @arg SMARTCARD_IT_PE: Parity error interrupt
* @retval The new state of __IT__ (TRUE or FALSE).
*/
#define __HAL_SMARTCARD_GET_IT_SOURCE(__HANDLE__, __IT__) ((((((uint8_t)(__IT__)) >> 5U) == 1)? (__HANDLE__)->Instance->CR1 : \
(((((uint8_t)(__IT__)) >> 5U) == 2)? (__HANDLE__)->Instance->CR2 : \
(__HANDLE__)->Instance->CR3)) & ((uint32_t)1 << (((uint16_t)(__IT__)) & SMARTCARD_IT_MASK)))
/** @brief Clear the specified SMARTCARD ISR flag, in setting the proper ICR register flag.
* @param __HANDLE__: specifies the SMARTCARD Handle.
* The Handle Instance can be USARTx where x: 1, 2 or 3 to select the USART peripheral.
* @param __IT_CLEAR__: specifies the interrupt clear register flag that needs to be set
* to clear the corresponding interrupt
* This parameter can be one of the following values:
* @arg SMARTCARD_CLEAR_PEF: Parity error clear flag
* @arg SMARTCARD_CLEAR_FEF: Framing error clear flag
* @arg SMARTCARD_CLEAR_NEF: Noise detected clear flag
* @arg SMARTCARD_CLEAR_OREF: OverRun error clear flag
* @arg SMARTCARD_CLEAR_IDLEF: Idle line detection clear flag
* @arg SMARTCARD_CLEAR_TCF: Transmission complete clear flag
* @arg SMARTCARD_CLEAR_RTOF: Receiver timeout clear flag
* @arg SMARTCARD_CLEAR_EOBF: End of block clear flag
* @retval None
*/
#define __HAL_SMARTCARD_CLEAR_IT(__HANDLE__, __IT_CLEAR__) ((__HANDLE__)->Instance->ICR = (uint32_t)(__IT_CLEAR__))
/** @brief Set a specific SMARTCARD request flag.
* @param __HANDLE__: specifies the SMARTCARD Handle.
* The Handle Instance can be USARTx where x: 1, 2 or 3 to select the USART peripheral.
* @param __REQ__: specifies the request flag to set
* This parameter can be one of the following values:
* @arg SMARTCARD_RXDATA_FLUSH_REQUEST: Receive data flush Request
* @arg SMARTCARD_TXDATA_FLUSH_REQUEST: Transmit data flush Request
*
* @retval None
*/
#define __HAL_SMARTCARD_SEND_REQ(__HANDLE__, __REQ__) ((__HANDLE__)->Instance->RQR |= (uint16_t)(__REQ__))
/** @brief Enable the SMARTCARD one bit sample method.
* @param __HANDLE__: specifies the SMARTCARD Handle.
* @retval None
*/
#define __HAL_SMARTCARD_ONE_BIT_SAMPLE_ENABLE(__HANDLE__) ((__HANDLE__)->Instance->CR3|= USART_CR3_ONEBIT)
/** @brief Disable the SMARTCARD one bit sample method.
* @param __HANDLE__: specifies the SMARTCARD Handle.
* @retval None
*/
#define __HAL_SMARTCARD_ONE_BIT_SAMPLE_DISABLE(__HANDLE__) ((__HANDLE__)->Instance->CR3 &= (uint32_t)~((uint32_t)USART_CR3_ONEBIT))
/** @brief Enable the USART associated to the SMARTCARD Handle.
* @param __HANDLE__: specifies the SMARTCARD Handle.
* The Handle Instance can be UARTx where x: 1, 2, 3 to select the USART peripheral
* @retval None
*/
#define __HAL_SMARTCARD_ENABLE(__HANDLE__) ((__HANDLE__)->Instance->CR1 |= USART_CR1_UE)
/** @brief Disable the USART associated to the SMARTCARD Handle
* @param __HANDLE__: specifies the SMARTCARD Handle.
* The Handle Instance can be UARTx where x: 1, 2, 3 to select the USART peripheral
* @retval None
*/
#define __HAL_SMARTCARD_DISABLE(__HANDLE__) ((__HANDLE__)->Instance->CR1 &= ~USART_CR1_UE)
/**
* @}
*/
/* Private macros -------------------------------------------------------------*/
/** @defgroup SMARTCARD_Private_Macros SMARTCARD Private Macros
* @{
*/
/** @brief Check the Baud rate range. The maximum Baud Rate is derived from the
* maximum clock on F0 (i.e. 48 MHz) divided by the oversampling used
* on the SMARTCARD (i.e. 16).
* @param __BAUDRATE__: Baud rate set by the configuration function.
* @retval Test result (TRUE or FALSE)
*/
#define IS_SMARTCARD_BAUDRATE(__BAUDRATE__) ((__BAUDRATE__) < 4500001)
/** @brief Check the block length range.
* @note The maximum SMARTCARD block length is 0xFF.
* @param __LENGTH__: block length.
* @retval Test result (TRUE or FALSE)
*/
#define IS_SMARTCARD_BLOCKLENGTH(__LENGTH__) ((__LENGTH__) <= 0xFF)
/** @brief Check the receiver timeout value.
* @note The maximum SMARTCARD receiver timeout value is 0xFFFFFF.
* @param __TIMEOUTVALUE__: receiver timeout value.
* @retval Test result (TRUE or FALSE)
*/
#define IS_SMARTCARD_TIMEOUT_VALUE(__TIMEOUTVALUE__) ((__TIMEOUTVALUE__) <= 0xFFFFFF)
/** @brief Check the SMARTCARD autoretry counter value.
* @note The maximum number of retransmissions is 0x7.
* @param __COUNT__: number of retransmissions.
* @retval Test result (TRUE or FALSE)
*/
#define IS_SMARTCARD_AUTORETRY_COUNT(__COUNT__) ((__COUNT__) <= 0x7)
/**
* @brief Ensure that SMARTCARD frame length is valid.
* @param __LENGTH__: SMARTCARD frame length.
* @retval SET (__LENGTH__ is valid) or RESET (__LENGTH__ is invalid)
*/
#define IS_SMARTCARD_WORD_LENGTH(__LENGTH__) ((__LENGTH__) == SMARTCARD_WORDLENGTH_9B)
/**
* @brief Ensure that SMARTCARD frame number of stop bits is valid.
* @param __STOPBITS__: SMARTCARD frame number of stop bits.
* @retval SET (__STOPBITS__ is valid) or RESET (__STOPBITS__ is invalid)
*/
#define IS_SMARTCARD_STOPBITS(__STOPBITS__) ((__STOPBITS__) == SMARTCARD_STOPBITS_1_5)
/**
* @brief Ensure that SMARTCARD frame parity is valid.
* @param __PARITY__: SMARTCARD frame parity.
* @retval SET (__PARITY__ is valid) or RESET (__PARITY__ is invalid)
*/
#define IS_SMARTCARD_PARITY(__PARITY__) (((__PARITY__) == SMARTCARD_PARITY_EVEN) || \
((__PARITY__) == SMARTCARD_PARITY_ODD))
/**
* @brief Ensure that SMARTCARD communication mode is valid.
* @param __MODE__: SMARTCARD communication mode.
* @retval SET (__MODE__ is valid) or RESET (__MODE__ is invalid)
*/
#define IS_SMARTCARD_MODE(__MODE__) ((((__MODE__) & (uint16_t)0xFFF3) == 0x00) && ((__MODE__) != (uint16_t)0x00))
/**
* @brief Ensure that SMARTCARD frame polarity is valid.
* @param __CPOL__: SMARTCARD frame polarity.
* @retval SET (__CPOL__ is valid) or RESET (__CPOL__ is invalid)
*/
#define IS_SMARTCARD_POLARITY(__CPOL__) (((__CPOL__) == SMARTCARD_POLARITY_LOW) || ((__CPOL__) == SMARTCARD_POLARITY_HIGH))
/**
* @brief Ensure that SMARTCARD frame phase is valid.
* @param __CPHA__: SMARTCARD frame phase.
* @retval SET (__CPHA__ is valid) or RESET (__CPHA__ is invalid)
*/
#define IS_SMARTCARD_PHASE(__CPHA__) (((__CPHA__) == SMARTCARD_PHASE_1EDGE) || ((__CPHA__) == SMARTCARD_PHASE_2EDGE))
/**
* @brief Ensure that SMARTCARD frame last bit clock pulse setting is valid.
* @param __LASTBIT__: SMARTCARD frame last bit clock pulse setting.
* @retval SET (__LASTBIT__ is valid) or RESET (__LASTBIT__ is invalid)
*/
#define IS_SMARTCARD_LASTBIT(__LASTBIT__) (((__LASTBIT__) == SMARTCARD_LASTBIT_DISABLE) || \
((__LASTBIT__) == SMARTCARD_LASTBIT_ENABLE))
/**
* @brief Ensure that SMARTCARD frame sampling is valid.
* @param __ONEBIT__: SMARTCARD frame sampling.
* @retval SET (__ONEBIT__ is valid) or RESET (__ONEBIT__ is invalid)
*/
#define IS_SMARTCARD_ONE_BIT_SAMPLE(__ONEBIT__) (((__ONEBIT__) == SMARTCARD_ONE_BIT_SAMPLE_DISABLE) || \
((__ONEBIT__) == SMARTCARD_ONE_BIT_SAMPLE_ENABLE))
/**
* @brief Ensure that SMARTCARD NACK transmission setting is valid.
* @param __NACK__: SMARTCARD NACK transmission setting.
* @retval SET (__NACK__ is valid) or RESET (__NACK__ is invalid)
*/
#define IS_SMARTCARD_NACK(__NACK__) (((__NACK__) == SMARTCARD_NACK_ENABLE) || \
((__NACK__) == SMARTCARD_NACK_DISABLE))
/**
* @brief Ensure that SMARTCARD receiver timeout setting is valid.
* @param __TIMEOUT__: SMARTCARD receiver timeout setting.
* @retval SET (__TIMEOUT__ is valid) or RESET (__TIMEOUT__ is invalid)
*/
#define IS_SMARTCARD_TIMEOUT(__TIMEOUT__) (((__TIMEOUT__) == SMARTCARD_TIMEOUT_DISABLE) || \
((__TIMEOUT__) == SMARTCARD_TIMEOUT_ENABLE))
/**
* @brief Ensure that SMARTCARD advanced features initialization is valid.
* @param __INIT__: SMARTCARD advanced features initialization.
* @retval SET (__INIT__ is valid) or RESET (__INIT__ is invalid)
*/
#define IS_SMARTCARD_ADVFEATURE_INIT(__INIT__) ((__INIT__) <= (SMARTCARD_ADVFEATURE_NO_INIT | \
SMARTCARD_ADVFEATURE_TXINVERT_INIT | \
SMARTCARD_ADVFEATURE_RXINVERT_INIT | \
SMARTCARD_ADVFEATURE_DATAINVERT_INIT | \
SMARTCARD_ADVFEATURE_SWAP_INIT | \
SMARTCARD_ADVFEATURE_RXOVERRUNDISABLE_INIT | \
SMARTCARD_ADVFEATURE_DMADISABLEONERROR_INIT | \
SMARTCARD_ADVFEATURE_MSBFIRST_INIT))
/**
* @brief Ensure that SMARTCARD frame TX inversion setting is valid.
* @param __TXINV__: SMARTCARD frame TX inversion setting.
* @retval SET (__TXINV__ is valid) or RESET (__TXINV__ is invalid)
*/
#define IS_SMARTCARD_ADVFEATURE_TXINV(__TXINV__) (((__TXINV__) == SMARTCARD_ADVFEATURE_TXINV_DISABLE) || \
((__TXINV__) == SMARTCARD_ADVFEATURE_TXINV_ENABLE))
/**
* @brief Ensure that SMARTCARD frame RX inversion setting is valid.
* @param __RXINV__: SMARTCARD frame RX inversion setting.
* @retval SET (__RXINV__ is valid) or RESET (__RXINV__ is invalid)
*/
#define IS_SMARTCARD_ADVFEATURE_RXINV(__RXINV__) (((__RXINV__) == SMARTCARD_ADVFEATURE_RXINV_DISABLE) || \
((__RXINV__) == SMARTCARD_ADVFEATURE_RXINV_ENABLE))
/**
* @brief Ensure that SMARTCARD frame data inversion setting is valid.
* @param __DATAINV__: SMARTCARD frame data inversion setting.
* @retval SET (__DATAINV__ is valid) or RESET (__DATAINV__ is invalid)
*/
#define IS_SMARTCARD_ADVFEATURE_DATAINV(__DATAINV__) (((__DATAINV__) == SMARTCARD_ADVFEATURE_DATAINV_DISABLE) || \
((__DATAINV__) == SMARTCARD_ADVFEATURE_DATAINV_ENABLE))
/**
* @brief Ensure that SMARTCARD frame RX/TX pins swap setting is valid.
* @param __SWAP__: SMARTCARD frame RX/TX pins swap setting.
* @retval SET (__SWAP__ is valid) or RESET (__SWAP__ is invalid)
*/
#define IS_SMARTCARD_ADVFEATURE_SWAP(__SWAP__) (((__SWAP__) == SMARTCARD_ADVFEATURE_SWAP_DISABLE) || \
((__SWAP__) == SMARTCARD_ADVFEATURE_SWAP_ENABLE))
/**
* @brief Ensure that SMARTCARD frame overrun setting is valid.
* @param __OVERRUN__: SMARTCARD frame overrun setting.
* @retval SET (__OVERRUN__ is valid) or RESET (__OVERRUN__ is invalid)
*/
#define IS_SMARTCARD_OVERRUN(__OVERRUN__) (((__OVERRUN__) == SMARTCARD_ADVFEATURE_OVERRUN_ENABLE) || \
((__OVERRUN__) == SMARTCARD_ADVFEATURE_OVERRUN_DISABLE))
/**
* @brief Ensure that SMARTCARD DMA enabling or disabling on error setting is valid.
* @param __DMA__: SMARTCARD DMA enabling or disabling on error setting.
* @retval SET (__DMA__ is valid) or RESET (__DMA__ is invalid)
*/
#define IS_SMARTCARD_ADVFEATURE_DMAONRXERROR(__DMA__) (((__DMA__) == SMARTCARD_ADVFEATURE_DMA_ENABLEONRXERROR) || \
((__DMA__) == SMARTCARD_ADVFEATURE_DMA_DISABLEONRXERROR))
/**
* @brief Ensure that SMARTCARD frame MSB first setting is valid.
* @param __MSBFIRST__: SMARTCARD frame MSB first setting.
* @retval SET (__MSBFIRST__ is valid) or RESET (__MSBFIRST__ is invalid)
*/
#define IS_SMARTCARD_ADVFEATURE_MSBFIRST(__MSBFIRST__) (((__MSBFIRST__) == SMARTCARD_ADVFEATURE_MSBFIRST_DISABLE) || \
((__MSBFIRST__) == SMARTCARD_ADVFEATURE_MSBFIRST_ENABLE))
/**
* @brief Ensure that SMARTCARD request parameter is valid.
* @param __PARAM__: SMARTCARD request parameter.
* @retval SET (__PARAM__ is valid) or RESET (__PARAM__ is invalid)
*/
#define IS_SMARTCARD_REQUEST_PARAMETER(__PARAM__) (((__PARAM__) == SMARTCARD_RXDATA_FLUSH_REQUEST) || \
((__PARAM__) == SMARTCARD_TXDATA_FLUSH_REQUEST))
/**
* @}
*/
/* Include SMARTCARD HAL Extended module */
#include "stm32f0xx_hal_smartcard_ex.h"
/* Exported functions --------------------------------------------------------*/
/** @addtogroup SMARTCARD_Exported_Functions SMARTCARD Exported Functions
* @{
*/
/** @addtogroup SMARTCARD_Exported_Functions_Group1 Initialization and de-initialization functions
* @{
*/
/* Initialization and de-initialization functions ****************************/
HAL_StatusTypeDef HAL_SMARTCARD_Init(SMARTCARD_HandleTypeDef *hsmartcard);
HAL_StatusTypeDef HAL_SMARTCARD_DeInit(SMARTCARD_HandleTypeDef *hsmartcard);
void HAL_SMARTCARD_MspInit(SMARTCARD_HandleTypeDef *hsmartcard);
void HAL_SMARTCARD_MspDeInit(SMARTCARD_HandleTypeDef *hsmartcard);
/**
* @}
*/
/** @addtogroup SMARTCARD_Exported_Functions_Group2 IO operation functions
* @{
*/
/* IO operation functions *****************************************************/
HAL_StatusTypeDef HAL_SMARTCARD_Transmit(SMARTCARD_HandleTypeDef *hsmartcard, uint8_t *pData, uint16_t Size, uint32_t Timeout);
HAL_StatusTypeDef HAL_SMARTCARD_Receive(SMARTCARD_HandleTypeDef *hsmartcard, uint8_t *pData, uint16_t Size, uint32_t Timeout);
HAL_StatusTypeDef HAL_SMARTCARD_Transmit_IT(SMARTCARD_HandleTypeDef *hsmartcard, uint8_t *pData, uint16_t Size);
HAL_StatusTypeDef HAL_SMARTCARD_Receive_IT(SMARTCARD_HandleTypeDef *hsmartcard, uint8_t *pData, uint16_t Size);
HAL_StatusTypeDef HAL_SMARTCARD_Transmit_DMA(SMARTCARD_HandleTypeDef *hsmartcard, uint8_t *pData, uint16_t Size);
HAL_StatusTypeDef HAL_SMARTCARD_Receive_DMA(SMARTCARD_HandleTypeDef *hsmartcard, uint8_t *pData, uint16_t Size);
void HAL_SMARTCARD_IRQHandler(SMARTCARD_HandleTypeDef *hsmartcard);
void HAL_SMARTCARD_TxCpltCallback(SMARTCARD_HandleTypeDef *hsmartcard);
void HAL_SMARTCARD_RxCpltCallback(SMARTCARD_HandleTypeDef *hsmartcard);
void HAL_SMARTCARD_ErrorCallback(SMARTCARD_HandleTypeDef *hsmartcard);
/**
* @}
*/
/** @addtogroup SMARTCARD_Exported_Functions_Group3 Peripheral State and Errors functions
* @{
*/
/* Peripheral State and Error functions ***************************************/
HAL_SMARTCARD_StateTypeDef HAL_SMARTCARD_GetState(SMARTCARD_HandleTypeDef *hsmartcard);
uint32_t HAL_SMARTCARD_GetError(SMARTCARD_HandleTypeDef *hsmartcard);
/**
* @}
*/
/**
* @}
*/
/**
* @}
*/
/**
* @}
*/
#endif /* !defined(STM32F030x6) && !defined(STM32F030x8)&& !defined(STM32F070x6) && !defined(STM32F070xB) && !defined(STM32F030xC) */
#ifdef __cplusplus
}
#endif
#endif /* __STM32F0xx_HAL_SMARTCARD_H */
/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/