SPKT
Dependencies: F746_GUI SD_PlayerSkeleton F746_SAI_IO
Diff: SRC_STM32F7/targets/cmsis/TARGET_STM/TARGET_STM32F7/stm32f7xx_hal_pwr.c
- Revision:
- 0:8ede47d38d10
--- /dev/null Thu Jan 01 00:00:00 1970 +0000 +++ b/SRC_STM32F7/targets/cmsis/TARGET_STM/TARGET_STM32F7/stm32f7xx_hal_pwr.c Tue Jun 04 21:37:21 2019 +0000 @@ -0,0 +1,609 @@ +/** + ****************************************************************************** + * @file stm32f7xx_hal_pwr.c + * @author MCD Application Team + * @version V1.0.4 + * @date 09-December-2015 + * @brief PWR HAL module driver. + * This file provides firmware functions to manage the following + * functionalities of the Power Controller (PWR) peripheral: + * + Initialization and de-initialization functions + * + Peripheral Control functions + * + ****************************************************************************** + * @attention + * + * <h2><center>© COPYRIGHT(c) 2015 STMicroelectronics</center></h2> + * + * Redistribution and use in source and binary forms, with or without modification, + * are permitted provided that the following conditions are met: + * 1. Redistributions of source code must retain the above copyright notice, + * this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright notice, + * this list of conditions and the following disclaimer in the documentation + * and/or other materials provided with the distribution. + * 3. Neither the name of STMicroelectronics nor the names of its contributors + * may be used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" + * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE + * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE + * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL + * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR + * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER + * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, + * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE + * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + * + ****************************************************************************** + */ + +/* Includes ------------------------------------------------------------------*/ +#include "stm32f7xx_hal.h" + +/** @addtogroup STM32F7xx_HAL_Driver + * @{ + */ + +/** @defgroup PWR PWR + * @brief PWR HAL module driver + * @{ + */ + +#ifdef HAL_PWR_MODULE_ENABLED + +/* Private typedef -----------------------------------------------------------*/ +/* Private define ------------------------------------------------------------*/ +/** @addtogroup PWR_Private_Constants + * @{ + */ + +/** @defgroup PWR_PVD_Mode_Mask PWR PVD Mode Mask + * @{ + */ +#define PVD_MODE_IT ((uint32_t)0x00010000) +#define PVD_MODE_EVT ((uint32_t)0x00020000) +#define PVD_RISING_EDGE ((uint32_t)0x00000001) +#define PVD_FALLING_EDGE ((uint32_t)0x00000002) +/** + * @} + */ + +/** @defgroup PWR_ENABLE_WUP_Mask PWR Enable WUP Mask + * @{ + */ +#define PWR_EWUP_MASK ((uint32_t)0x00003F00) +/** + * @} + */ + +/** + * @} + */ +/* Private macro -------------------------------------------------------------*/ +/* Private variables ---------------------------------------------------------*/ +/* Private function prototypes -----------------------------------------------*/ +/* Private functions ---------------------------------------------------------*/ + +/** @defgroup PWR_Exported_Functions PWR Exported Functions + * @{ + */ + +/** @defgroup PWR_Exported_Functions_Group1 Initialization and de-initialization functions + * @brief Initialization and de-initialization functions + * +@verbatim + =============================================================================== + ##### Initialization and de-initialization functions ##### + =============================================================================== + [..] + After reset, the backup domain (RTC registers, RTC backup data + registers and backup SRAM) is protected against possible unwanted + write accesses. + To enable access to the RTC Domain and RTC registers, proceed as follows: + (+) Enable the Power Controller (PWR) APB1 interface clock using the + __HAL_RCC_PWR_CLK_ENABLE() macro. + (+) Enable access to RTC domain using the HAL_PWR_EnableBkUpAccess() function. + +@endverbatim + * @{ + */ + +/** + * @brief Deinitializes the HAL PWR peripheral registers to their default reset values. + * @retval None + */ +void HAL_PWR_DeInit(void) +{ + __HAL_RCC_PWR_FORCE_RESET(); + __HAL_RCC_PWR_RELEASE_RESET(); +} + +/** + * @brief Enables access to the backup domain (RTC registers, RTC + * backup data registers and backup SRAM). + * @note If the HSE divided by 2, 3, ..31 is used as the RTC clock, the + * Backup Domain Access should be kept enabled. + * @retval None + */ +void HAL_PWR_EnableBkUpAccess(void) +{ + /* Enable access to RTC and backup registers */ + SET_BIT(PWR->CR1, PWR_CR1_DBP); +} + +/** + * @brief Disables access to the backup domain (RTC registers, RTC + * backup data registers and backup SRAM). + * @note If the HSE divided by 2, 3, ..31 is used as the RTC clock, the + * Backup Domain Access should be kept enabled. + * @retval None + */ +void HAL_PWR_DisableBkUpAccess(void) +{ + /* Disable access to RTC and backup registers */ + CLEAR_BIT(PWR->CR1, PWR_CR1_DBP); +} + +/** + * @} + */ + +/** @defgroup PWR_Exported_Functions_Group2 Peripheral Control functions + * @brief Low Power modes configuration functions + * +@verbatim + + =============================================================================== + ##### Peripheral Control functions ##### + =============================================================================== + + *** PVD configuration *** + ========================= + [..] + (+) The PVD is used to monitor the VDD power supply by comparing it to a + threshold selected by the PVD Level (PLS[2:0] bits in the PWR_CR). + (+) A PVDO flag is available to indicate if VDD/VDDA is higher or lower + than the PVD threshold. This event is internally connected to the EXTI + line16 and can generate an interrupt if enabled. This is done through + __HAL_PWR_PVD_EXTI_ENABLE_IT() macro. + (+) The PVD is stopped in Standby mode. + + *** Wake-up pin configuration *** + ================================ + [..] + (+) Wake-up pin is used to wake up the system from Standby mode. This pin is + forced in input pull-down configuration and is active on rising edges. + (+) There are to 6 Wake-up pin in the STM32F7 devices family + + *** Low Power modes configuration *** + ===================================== + [..] + The devices feature 3 low-power modes: + (+) Sleep mode: Cortex-M7 core stopped, peripherals kept running. + (+) Stop mode: all clocks are stopped, regulator running, regulator + in low power mode + (+) Standby mode: 1.2V domain powered off. + + *** Sleep mode *** + ================== + [..] + (+) Entry: + The Sleep mode is entered by using the HAL_PWR_EnterSLEEPMode(PWR_MAINREGULATOR_ON, PWR_SLEEPENTRY_WFI) + functions with + (++) PWR_SLEEPENTRY_WFI: enter SLEEP mode with WFI instruction + (++) PWR_SLEEPENTRY_WFE: enter SLEEP mode with WFE instruction + + -@@- The Regulator parameter is not used for the STM32F7 family + and is kept as parameter just to maintain compatibility with the + lower power families (STM32L). + (+) Exit: + Any peripheral interrupt acknowledged by the nested vectored interrupt + controller (NVIC) can wake up the device from Sleep mode. + + *** Stop mode *** + ================= + [..] + In Stop mode, all clocks in the 1.2V domain are stopped, the PLL, the HSI, + and the HSE RC oscillators are disabled. Internal SRAM and register contents + are preserved. + The voltage regulator can be configured either in normal or low-power mode. + To minimize the consumption In Stop mode, FLASH can be powered off before + entering the Stop mode using the HAL_PWREx_EnableFlashPowerDown() function. + It can be switched on again by software after exiting the Stop mode using + the HAL_PWREx_DisableFlashPowerDown() function. + + (+) Entry: + The Stop mode is entered using the HAL_PWR_EnterSTOPMode(PWR_MAINREGULATOR_ON) + function with: + (++) Main regulator ON. + (++) Low Power regulator ON. + (+) Exit: + Any EXTI Line (Internal or External) configured in Interrupt/Event mode. + + *** Standby mode *** + ==================== + [..] + (+) + The Standby mode allows to achieve the lowest power consumption. It is based + on the Cortex-M7 deep sleep mode, with the voltage regulator disabled. + The 1.2V domain is consequently powered off. The PLL, the HSI oscillator and + the HSE oscillator are also switched off. SRAM and register contents are lost + except for the RTC registers, RTC backup registers, backup SRAM and Standby + circuitry. + + The voltage regulator is OFF. + + (++) Entry: + (+++) The Standby mode is entered using the HAL_PWR_EnterSTANDBYMode() function. + (++) Exit: + (+++) WKUP pin rising or falling edge, RTC alarm (Alarm A and Alarm B), RTC + wakeup, tamper event, time stamp event, external reset in NRST pin, IWDG reset. + + *** Auto-wakeup (AWU) from low-power mode *** + ============================================= + [..] + + (+) The MCU can be woken up from low-power mode by an RTC Alarm event, an RTC + Wakeup event, a tamper event or a time-stamp event, without depending on + an external interrupt (Auto-wakeup mode). + + (+) RTC auto-wakeup (AWU) from the Stop and Standby modes + + (++) To wake up from the Stop mode with an RTC alarm event, it is necessary to + configure the RTC to generate the RTC alarm using the HAL_RTC_SetAlarm_IT() function. + + (++) To wake up from the Stop mode with an RTC Tamper or time stamp event, it + is necessary to configure the RTC to detect the tamper or time stamp event using the + HAL_RTCEx_SetTimeStamp_IT() or HAL_RTCEx_SetTamper_IT() functions. + + (++) To wake up from the Stop mode with an RTC WakeUp event, it is necessary to + configure the RTC to generate the RTC WakeUp event using the HAL_RTCEx_SetWakeUpTimer_IT() function. + +@endverbatim + * @{ + */ + +/** + * @brief Configures the voltage threshold detected by the Power Voltage Detector(PVD). + * @param sConfigPVD: pointer to an PWR_PVDTypeDef structure that contains the configuration + * information for the PVD. + * @note Refer to the electrical characteristics of your device datasheet for + * more details about the voltage threshold corresponding to each + * detection level. + * @retval None + */ +void HAL_PWR_ConfigPVD(PWR_PVDTypeDef *sConfigPVD) +{ + /* Check the parameters */ + assert_param(IS_PWR_PVD_LEVEL(sConfigPVD->PVDLevel)); + assert_param(IS_PWR_PVD_MODE(sConfigPVD->Mode)); + + /* Set PLS[7:5] bits according to PVDLevel value */ + MODIFY_REG(PWR->CR1, PWR_CR1_PLS, sConfigPVD->PVDLevel); + + /* Clear any previous config. Keep it clear if no event or IT mode is selected */ + __HAL_PWR_PVD_EXTI_DISABLE_EVENT(); + __HAL_PWR_PVD_EXTI_DISABLE_IT(); + __HAL_PWR_PVD_EXTI_DISABLE_RISING_EDGE(); + __HAL_PWR_PVD_EXTI_DISABLE_FALLING_EDGE(); + + /* Configure interrupt mode */ + if((sConfigPVD->Mode & PVD_MODE_IT) == PVD_MODE_IT) + { + __HAL_PWR_PVD_EXTI_ENABLE_IT(); + } + + /* Configure event mode */ + if((sConfigPVD->Mode & PVD_MODE_EVT) == PVD_MODE_EVT) + { + __HAL_PWR_PVD_EXTI_ENABLE_EVENT(); + } + + /* Configure the edge */ + if((sConfigPVD->Mode & PVD_RISING_EDGE) == PVD_RISING_EDGE) + { + __HAL_PWR_PVD_EXTI_ENABLE_RISING_EDGE(); + } + + if((sConfigPVD->Mode & PVD_FALLING_EDGE) == PVD_FALLING_EDGE) + { + __HAL_PWR_PVD_EXTI_ENABLE_FALLING_EDGE(); + } +} + +/** + * @brief Enables the Power Voltage Detector(PVD). + * @retval None + */ +void HAL_PWR_EnablePVD(void) +{ + /* Enable the power voltage detector */ + SET_BIT(PWR->CR1, PWR_CR1_PVDE); +} + +/** + * @brief Disables the Power Voltage Detector(PVD). + * @retval None + */ +void HAL_PWR_DisablePVD(void) +{ + /* Disable the power voltage detector */ + CLEAR_BIT(PWR->CR1, PWR_CR1_PVDE); +} + +/** + * @brief Enable the WakeUp PINx functionality. + * @param WakeUpPinPolarity: Specifies which Wake-Up pin to enable. + * This parameter can be one of the following legacy values, which sets the default polarity: + * detection on high level (rising edge): + * @arg PWR_WAKEUP_PIN1, PWR_WAKEUP_PIN2, PWR_WAKEUP_PIN3, PWR_WAKEUP_PIN4, PWR_WAKEUP_PIN5, PWR_WAKEUP_PIN6 + * or one of the following value where the user can explicitly states the enabled pin and + * the chosen polarity + * @arg PWR_WAKEUP_PIN1_HIGH or PWR_WAKEUP_PIN1_LOW + * @arg PWR_WAKEUP_PIN2_HIGH or PWR_WAKEUP_PIN2_LOW + * @arg PWR_WAKEUP_PIN3_HIGH or PWR_WAKEUP_PIN3_LOW + * @arg PWR_WAKEUP_PIN4_HIGH or PWR_WAKEUP_PIN4_LOW + * @arg PWR_WAKEUP_PIN5_HIGH or PWR_WAKEUP_PIN5_LOW + * @arg PWR_WAKEUP_PIN6_HIGH or PWR_WAKEUP_PIN6_LOW + * @note PWR_WAKEUP_PINx and PWR_WAKEUP_PINx_HIGH are equivalent. + * @retval None + */ +void HAL_PWR_EnableWakeUpPin(uint32_t WakeUpPinPolarity) +{ + assert_param(IS_PWR_WAKEUP_PIN(WakeUpPinPolarity)); + + /* Enable wake-up pin */ + SET_BIT(PWR->CSR2, (PWR_EWUP_MASK & WakeUpPinPolarity)); + + /* Specifies the Wake-Up pin polarity for the event detection + (rising or falling edge) */ + MODIFY_REG(PWR->CR2, (PWR_EWUP_MASK & WakeUpPinPolarity), (WakeUpPinPolarity >> 0x06)); +} + +/** + * @brief Disables the WakeUp PINx functionality. + * @param WakeUpPinx: Specifies the Power Wake-Up pin to disable. + * This parameter can be one of the following values: + * @arg PWR_WAKEUP_PIN1 + * @arg PWR_WAKEUP_PIN2 + * @arg PWR_WAKEUP_PIN3 + * @arg PWR_WAKEUP_PIN4 + * @arg PWR_WAKEUP_PIN5 + * @arg PWR_WAKEUP_PIN6 + * @retval None + */ +void HAL_PWR_DisableWakeUpPin(uint32_t WakeUpPinx) +{ + assert_param(IS_PWR_WAKEUP_PIN(WakeUpPinx)); + + CLEAR_BIT(PWR->CSR2, WakeUpPinx); +} + +/** + * @brief Enters Sleep mode. + * + * @note In Sleep mode, all I/O pins keep the same state as in Run mode. + * + * @note In Sleep mode, the systick is stopped to avoid exit from this mode with + * systick interrupt when used as time base for Timeout + * + * @param Regulator: Specifies the regulator state in SLEEP mode. + * This parameter can be one of the following values: + * @arg PWR_MAINREGULATOR_ON: SLEEP mode with regulator ON + * @arg PWR_LOWPOWERREGULATOR_ON: SLEEP mode with low power regulator ON + * @note This parameter is not used for the STM32F7 family and is kept as parameter + * just to maintain compatibility with the lower power families. + * @param SLEEPEntry: Specifies if SLEEP mode in entered with WFI or WFE instruction. + * This parameter can be one of the following values: + * @arg PWR_SLEEPENTRY_WFI: enter SLEEP mode with WFI instruction + * @arg PWR_SLEEPENTRY_WFE: enter SLEEP mode with WFE instruction + * @retval None + */ +void HAL_PWR_EnterSLEEPMode(uint32_t Regulator, uint8_t SLEEPEntry) +{ + /* Check the parameters */ + assert_param(IS_PWR_REGULATOR(Regulator)); + assert_param(IS_PWR_SLEEP_ENTRY(SLEEPEntry)); + + /* Clear SLEEPDEEP bit of Cortex System Control Register */ + CLEAR_BIT(SCB->SCR, ((uint32_t)SCB_SCR_SLEEPDEEP_Msk)); + + /* Select SLEEP mode entry -------------------------------------------------*/ + if(SLEEPEntry == PWR_SLEEPENTRY_WFI) + { + /* Request Wait For Interrupt */ + __WFI(); + } + else + { + /* Request Wait For Event */ + __SEV(); + __WFE(); + __WFE(); + } +} + +/** + * @brief Enters Stop mode. + * @note In Stop mode, all I/O pins keep the same state as in Run mode. + * @note When exiting Stop mode by issuing an interrupt or a wakeup event, + * the HSI RC oscillator is selected as system clock. + * @note When the voltage regulator operates in low power mode, an additional + * startup delay is incurred when waking up from Stop mode. + * By keeping the internal regulator ON during Stop mode, the consumption + * is higher although the startup time is reduced. + * @param Regulator: Specifies the regulator state in Stop mode. + * This parameter can be one of the following values: + * @arg PWR_MAINREGULATOR_ON: Stop mode with regulator ON + * @arg PWR_LOWPOWERREGULATOR_ON: Stop mode with low power regulator ON + * @param STOPEntry: Specifies if Stop mode in entered with WFI or WFE instruction. + * This parameter can be one of the following values: + * @arg PWR_STOPENTRY_WFI: Enter Stop mode with WFI instruction + * @arg PWR_STOPENTRY_WFE: Enter Stop mode with WFE instruction + * @retval None + */ +void HAL_PWR_EnterSTOPMode(uint32_t Regulator, uint8_t STOPEntry) +{ + uint32_t tmpreg = 0; + + /* Check the parameters */ + assert_param(IS_PWR_REGULATOR(Regulator)); + assert_param(IS_PWR_STOP_ENTRY(STOPEntry)); + + /* Select the regulator state in Stop mode ---------------------------------*/ + tmpreg = PWR->CR1; + /* Clear PDDS and LPDS bits */ + tmpreg &= (uint32_t)~(PWR_CR1_PDDS | PWR_CR1_LPDS); + + /* Set LPDS, MRLVDS and LPLVDS bits according to Regulator value */ + tmpreg |= Regulator; + + /* Store the new value */ + PWR->CR1 = tmpreg; + + /* Set SLEEPDEEP bit of Cortex System Control Register */ + SCB->SCR |= SCB_SCR_SLEEPDEEP_Msk; + + /* Select Stop mode entry --------------------------------------------------*/ + if(STOPEntry == PWR_STOPENTRY_WFI) + { + /* Request Wait For Interrupt */ + __WFI(); + } + else + { + /* Request Wait For Event */ + __SEV(); + __WFE(); + __WFE(); + } + /* Reset SLEEPDEEP bit of Cortex System Control Register */ + SCB->SCR &= (uint32_t)~((uint32_t)SCB_SCR_SLEEPDEEP_Msk); +} + +/** + * @brief Enters Standby mode. + * @note In Standby mode, all I/O pins are high impedance except for: + * - Reset pad (still available) + * - RTC_AF1 pin (PC13) if configured for tamper, time-stamp, RTC + * Alarm out, or RTC clock calibration out. + * - RTC_AF2 pin (PI8) if configured for tamper or time-stamp. + * - WKUP pins if enabled. + * @retval None + */ +void HAL_PWR_EnterSTANDBYMode(void) +{ + /* Select Standby mode */ + PWR->CR1 |= PWR_CR1_PDDS; + + /* Set SLEEPDEEP bit of Cortex System Control Register */ + SCB->SCR |= SCB_SCR_SLEEPDEEP_Msk; + + /* This option is used to ensure that store operations are completed */ +#if defined ( __CC_ARM) + __force_stores(); +#endif + /* Request Wait For Interrupt */ + __WFI(); +} + +/** + * @brief This function handles the PWR PVD interrupt request. + * @note This API should be called under the PVD_IRQHandler(). + * @retval None + */ +void HAL_PWR_PVD_IRQHandler(void) +{ + /* Check PWR Exti flag */ + if(__HAL_PWR_PVD_EXTI_GET_FLAG() != RESET) + { + /* PWR PVD interrupt user callback */ + HAL_PWR_PVDCallback(); + + /* Clear PWR Exti pending bit */ + __HAL_PWR_PVD_EXTI_CLEAR_FLAG(); + } +} + +/** + * @brief PWR PVD interrupt callback + * @retval None + */ +__weak void HAL_PWR_PVDCallback(void) +{ + /* NOTE : This function Should not be modified, when the callback is needed, + the HAL_PWR_PVDCallback could be implemented in the user file + */ +} + +/** + * @brief Indicates Sleep-On-Exit when returning from Handler mode to Thread mode. + * @note Set SLEEPONEXIT bit of SCR register. When this bit is set, the processor + * re-enters SLEEP mode when an interruption handling is over. + * Setting this bit is useful when the processor is expected to run only on + * interruptions handling. + * @retval None + */ +void HAL_PWR_EnableSleepOnExit(void) +{ + /* Set SLEEPONEXIT bit of Cortex System Control Register */ + SET_BIT(SCB->SCR, ((uint32_t)SCB_SCR_SLEEPONEXIT_Msk)); +} + +/** + * @brief Disables Sleep-On-Exit feature when returning from Handler mode to Thread mode. + * @note Clears SLEEPONEXIT bit of SCR register. When this bit is set, the processor + * re-enters SLEEP mode when an interruption handling is over. + * @retval None + */ +void HAL_PWR_DisableSleepOnExit(void) +{ + /* Clear SLEEPONEXIT bit of Cortex System Control Register */ + CLEAR_BIT(SCB->SCR, ((uint32_t)SCB_SCR_SLEEPONEXIT_Msk)); +} + +/** + * @brief Enables CORTEX M4 SEVONPEND bit. + * @note Sets SEVONPEND bit of SCR register. When this bit is set, this causes + * WFE to wake up when an interrupt moves from inactive to pended. + * @retval None + */ +void HAL_PWR_EnableSEVOnPend(void) +{ + /* Set SEVONPEND bit of Cortex System Control Register */ + SET_BIT(SCB->SCR, ((uint32_t)SCB_SCR_SEVONPEND_Msk)); +} + +/** + * @brief Disables CORTEX M4 SEVONPEND bit. + * @note Clears SEVONPEND bit of SCR register. When this bit is set, this causes + * WFE to wake up when an interrupt moves from inactive to pended. + * @retval None + */ +void HAL_PWR_DisableSEVOnPend(void) +{ + /* Clear SEVONPEND bit of Cortex System Control Register */ + CLEAR_BIT(SCB->SCR, ((uint32_t)SCB_SCR_SEVONPEND_Msk)); +} + +/** + * @} + */ + +/** + * @} + */ + +#endif /* HAL_PWR_MODULE_ENABLED */ +/** + * @} + */ + +/** + * @} + */ + +/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/