File content as of revision 0:ecac7a6076f0:

#ifndef H3LIS331_H
#define H3LIS331_H

/**
 * Includes
 */
#include "mbed.h"

/**
 * Defines
 */
#define H3LIS331_I2C_ADDRESS 0x18 //7-bit address.

//-----------
// Registers
//-----------
#define WHO_AM_I_REG_H3LIS331    0x0F
#define ACCEL_XOUT_H_REG         0x29
#define ACCEL_XOUT_L_REG         0x28
#define ACCEL_YOUT_H_REG         0x2B
#define ACCEL_YOUT_L_REG         0x2A
#define ACCEL_ZOUT_H_REG         0x2D
#define ACCEL_ZOUT_L_REG         0x2C



#define CTRL_REG_1      0x20
#define CTRL_REG_2      0x21
#define CTRL_REG_3      0x22
#define CTRL_REG_4      0x23
#define CTRL_REG_5      0x24

#define STATUS_REG      0x27

#define INT1_CFG        0x30
#define INT1_SRC        0x31
#define INT1_THS        0x32
#define INT1_DURATION   0x33
#define INT2_CFG        0x34
#define INT2_SRC        0x35
#define INT2_THS        0x36
#define INT2_DURATION   0x37

//------------------------------
// Power Mode and Output Data Rates
//------------------------------
#define POWER_DOWN             0x00
#define NORMAL_50HZ            0x27
#define NORMAL_100HZ           0x2F
#define NORMAL_400HZ           0x37
#define NORMAL_1000HZ          0x3F
#define LOW_POWER_0_5HZ        0x47
#define LOW_POWER_1HZ          0x67
#define LOW_POWER_2HZ          0x87
#define LOW_POWER_5HZ          0xA7
#define LOW_POWER_10HZ         0xC7

/**
 * H3LIS331 triple axis digital accelerometer.
 */
class H3LIS331 {

public:

    /**
     * Constructor.
     *
     * Sets FS_SEL to 0x03 for proper opertaion.
     *
     * @param sda - mbed pin to use for the SDA I2C line.
     * @param scl - mbed pin to use for the SCL I2C line.
     */
    H3LIS331(PinName sda, PinName scl);

    /**
     * Get the identity of the device.
     *
     * @return The contents of the Who Am I register which contains the I2C
     *         address of the device.
     */
    char getWhoAmI(void);

  
    
    
   

    
    
    
    /**
     * Set the power mode (power down, low power, normal mode)
     *
     *
     * @param 
     *
     *  Power Mode | Output Data Rate (Hz) | Low-pass Filter Cut off (Hz) | #define
     *  --------------------------------------------------------------------------------
     *  Power-down |          --           |               --             | POWER_DOWN
     *    Normal   |          50           |               37             | NORMAL_50HZ
     *    Normal   |         100           |               74             | NORMAL_100HZ
     *    Normal   |         400           |              292             | NORMAL_400HZ
     *    Normal   |        1000           |              780             | NORMAL_1000HZ
     *   Low-power |         0.5           |               --             | LOW_POWER_0_5HZ
     *   Low-power |           1           |               --             | LOW_POWER_1HZ
     *   Low-power |           2           |               --             | LOW_POWER_2HZ
     *   Low-power |           5           |               --             | LOW_POWER_5HZ
     *   Low-power |          10           |               --             | LOW_POWER_10HZ
     */
    
    void setPowerMode(char power_mode);
  
   
   
     /**
     * Get the current power mode
     *
     * @return 
     */
    char getPowerMode(void);

    
   char getInterruptConfiguration(void);

    /**
     * Set the interrupt configuration.
     *
     * See datasheet for configuration byte details.
     *
     *    7        6       5      4
     * +-------+-------+------+--------+
     * |  IHL  | PP_OD | LIR2 | I2_CFG |
     * +-------+-------+------+--------+
     *
     *      3        2       1         0
     * +---------+------+---------+---------+
     * | I2_CFG0 | LIR1 | I1_CFG1 | I1-CFG0 |
     * +---------+------+---------+---------+
     *
     * IHL Interrupt active high or low. 0:active high; 1:active low (default:0)
     * PP_OD Push-pull/Open drain selection on interrupt pad. 0:push-pull; 1:open drain (default:0)
     * LIR2 Latch interupt request on INT2_SRC register, with INT2_SRC register cleared by reading INT2_SRC itself
     *      0: irq not latched; 1:irq latched (default:0)
     * I2_CFG1, I2_CFG0 See datasheet table
     * LIR1 Latch interupt request on INT1_SRC register, with INT1_SRC register cleared by reading INT1_SRC itself
     *      0: irq not latched; 1:irq latched (default:0)
     * I1_CFG1, I1_CFG0 See datasheet table
     *
     * @param config Configuration byte to write to INT_CFG register.
     */
   
   
   // void setInterruptConfiguration(char config);

    /**
     * Check the status register
     *
     * @return 
     *
     */
     
     
    /**
     * Set the Full Scale Range to +/- 400g's.
     *
     */     
    void setFullScaleRange400g(void);

    /**
     * Set the Full Scale Range to +/- 200g's.
     *
     */     
    void setFullScaleRange200g(void);

    /**
     * Set the Full Scale Range to +/- 100g's.
     *
     */     
    void setFullScaleRange100g(void);
     
            
    char getAccelStatus(void);




    /**
     * Get the output for the x-axis accelerometer.
     *
     * @return The output on the x-axis in engineering units (g's).
     */
    float getAccelX(void);

    /**
     * Get the output for the y-axis accelerometer.
     *
     * @return The output on the y-axis in engineering units (g's).
     */
    float getAccelY(void);

    /**
     * Get the output on the z-axis accelerometer.
     * 
     * @return The output on the z-axis in engineering units (g's).
     */
    float getAccelZ(void);

   
private:

   float scaling_factor;
   int current_range;

    I2C i2c_;

};

#endif /* H3LIS331_H */