Part of MicroGen4 Music Synthesizer Program. (But not test it yet.) I2S ,DMA ,Stereo ,16Bit Dac(PCM1781) See detail: http://www.geocities.jp/micro_diys/index2
stm32f4xx_hal_conf.h
00001 /** 00002 ****************************************************************************** 00003 * @file stm32f4xx_hal_conf.h 00004 * @brief HAL configuration file. 00005 ****************************************************************************** 00006 * @attention 00007 * 00008 * <h2><center>© COPYRIGHT(c) 2014 STMicroelectronics</center></h2> 00009 * 00010 * Redistribution and use in source and binary forms, with or without modification, 00011 * are permitted provided that the following conditions are met: 00012 * 1. Redistributions of source code must retain the above copyright notice, 00013 * this list of conditions and the following disclaimer. 00014 * 2. Redistributions in binary form must reproduce the above copyright notice, 00015 * this list of conditions and the following disclaimer in the documentation 00016 * and/or other materials provided with the distribution. 00017 * 3. Neither the name of STMicroelectronics nor the names of its contributors 00018 * may be used to endorse or promote products derived from this software 00019 * without specific prior written permission. 00020 * 00021 * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" 00022 * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE 00023 * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE 00024 * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE 00025 * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL 00026 * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR 00027 * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER 00028 * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, 00029 * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE 00030 * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. 00031 * 00032 ****************************************************************************** 00033 */ 00034 00035 /* Define to prevent recursive inclusion -------------------------------------*/ 00036 #ifndef __STM32F4xx_HAL_CONF_H 00037 #define __STM32F4xx_HAL_CONF_H 00038 00039 #ifdef __cplusplus 00040 extern "C" { 00041 #endif 00042 00043 /* Exported types ------------------------------------------------------------*/ 00044 /* Exported constants --------------------------------------------------------*/ 00045 00046 /* ########################## Module Selection ############################## */ 00047 /** 00048 * @brief This is the list of modules to be used in the HAL driver 00049 */ 00050 #define HAL_MODULE_ENABLED 00051 //#define HAL_ADC_MODULE_ENABLED 00052 //#define HAL_CAN_MODULE_ENABLED 00053 //#define HAL_CRC_MODULE_ENABLED 00054 //#define HAL_CRYP_MODULE_ENABLED 00055 //#define HAL_DAC_MODULE_ENABLED 00056 //#define HAL_DCMI_MODULE_ENABLED 00057 //#define HAL_DMA2D_MODULE_ENABLED 00058 //#define HAL_ETH_MODULE_ENABLED 00059 //#define HAL_NAND_MODULE_ENABLED 00060 //#define HAL_NOR_MODULE_ENABLED 00061 //#define HAL_PCCARD_MODULE_ENABLED 00062 //#define HAL_SRAM_MODULE_ENABLED 00063 //#define HAL_SDRAM_MODULE_ENABLED 00064 //#define HAL_HASH_MODULE_ENABLED 00065 #define HAL_I2C_MODULE_ENABLED 00066 #define HAL_I2S_MODULE_ENABLED 00067 //#define HAL_IWDG_MODULE_ENABLED 00068 //#define HAL_LTDC_MODULE_ENABLED 00069 //#define HAL_RNG_MODULE_ENABLED 00070 //#define HAL_RTC_MODULE_ENABLED 00071 //#define HAL_SAI_MODULE_ENABLED 00072 //#define HAL_SD_MODULE_ENABLED 00073 //#define HAL_SPI_MODULE_ENABLED 00074 //#define HAL_TIM_MODULE_ENABLED 00075 #define HAL_UART_MODULE_ENABLED 00076 //#define HAL_USART_MODULE_ENABLED 00077 //#define HAL_IRDA_MODULE_ENABLED 00078 //#define HAL_SMARTCARD_MODULE_ENABLED 00079 //#define HAL_WWDG_MODULE_ENABLED 00080 //#define HAL_PCD_MODULE_ENABLED 00081 //#define HAL_HCD_MODULE_ENABLED 00082 #define HAL_GPIO_MODULE_ENABLED 00083 #define HAL_DMA_MODULE_ENABLED 00084 #define HAL_RCC_MODULE_ENABLED 00085 #define HAL_FLASH_MODULE_ENABLED 00086 #define HAL_PWR_MODULE_ENABLED 00087 #define HAL_CORTEX_MODULE_ENABLED 00088 00089 /* ########################## HSE/HSI Values adaptation ##################### */ 00090 /** 00091 * @brief Adjust the value of External High Speed oscillator (HSE) used in your application. 00092 * This value is used by the RCC HAL module to compute the system frequency 00093 * (when HSE is used as system clock source, directly or through the PLL). 00094 */ 00095 #if !defined (HSE_VALUE) 00096 #define HSE_VALUE ((uint32_t)25000000) /*!< Value of the External oscillator in Hz */ 00097 #endif /* HSE_VALUE */ 00098 00099 #if !defined (HSE_STARTUP_TIMEOUT) 00100 #define HSE_STARTUP_TIMEOUT ((uint32_t)5000) /*!< Time out for HSE start up, in ms */ 00101 #endif /* HSE_STARTUP_TIMEOUT */ 00102 00103 /** 00104 * @brief Internal High Speed oscillator (HSI) value. 00105 * This value is used by the RCC HAL module to compute the system frequency 00106 * (when HSI is used as system clock source, directly or through the PLL). 00107 */ 00108 #if !defined (HSI_VALUE) 00109 #define HSI_VALUE ((uint32_t)16000000) /*!< Value of the Internal oscillator in Hz*/ 00110 #endif /* HSI_VALUE */ 00111 00112 /** 00113 * @brief External clock source for I2S peripheral 00114 * This value is used by the I2S HAL module to compute the I2S clock source 00115 * frequency, this source is inserted directly through I2S_CKIN pad. 00116 */ 00117 #if !defined (EXTERNAL_CLOCK_VALUE) 00118 #define EXTERNAL_CLOCK_VALUE ((uint32_t)12288000) /*!< Value of the External audio frequency in Hz*/ 00119 #endif /* EXTERNAL_CLOCK_VALUE */ 00120 00121 /* Tip: To avoid modifying this file each time you need to use different HSE, 00122 === you can define the HSE value in your toolchain compiler preprocessor. */ 00123 00124 /* ########################### System Configuration ######################### */ 00125 /** 00126 * @brief This is the HAL system configuration section 00127 */ 00128 00129 #define VDD_VALUE ((uint32_t)3300) /*!< Value of VDD in mv */ 00130 #define USE_RTOS 0 00131 #define PREFETCH_ENABLE 1 00132 #define INSTRUCTION_CACHE_ENABLE 1 00133 #define DATA_CACHE_ENABLE 1 00134 00135 /* ########################## Assert Selection ############################## */ 00136 /** 00137 * @brief Uncomment the line below to expanse the "assert_param" macro in the 00138 * HAL drivers code 00139 */ 00140 /* #define USE_FULL_ASSERT 1 */ 00141 00142 /* ################## Ethernet peripheral configuration ##################### */ 00143 00144 /* Section 1 : Ethernet peripheral configuration */ 00145 00146 /* MAC ADDRESS: MAC_ADDR0:MAC_ADDR1:MAC_ADDR2:MAC_ADDR3:MAC_ADDR4:MAC_ADDR5 */ 00147 #define MAC_ADDR0 2 00148 #define MAC_ADDR1 0 00149 #define MAC_ADDR2 0 00150 #define MAC_ADDR3 0 00151 #define MAC_ADDR4 0 00152 #define MAC_ADDR5 0 00153 00154 /* Definition of the Ethernet driver buffers size and count */ 00155 #define ETH_RX_BUF_SIZE ETH_MAX_PACKET_SIZE /* buffer size for receive */ 00156 #define ETH_TX_BUF_SIZE ETH_MAX_PACKET_SIZE /* buffer size for transmit */ 00157 #define ETH_RXBUFNB ((uint32_t)4) /* 4 Rx buffers of size ETH_RX_BUF_SIZE */ 00158 #define ETH_TXBUFNB ((uint32_t)4) /* 4 Tx buffers of size ETH_TX_BUF_SIZE */ 00159 00160 /* Section 2: PHY configuration section */ 00161 00162 /* DP83848 PHY Address*/ 00163 #define DP83848_PHY_ADDRESS 0x01 00164 /* PHY Reset delay these values are based on a 1 ms Systick interrupt*/ 00165 #define PHY_RESET_DELAY ((uint32_t)0x000000FF) 00166 /* PHY Configuration delay */ 00167 #define PHY_CONFIG_DELAY ((uint32_t)0x00000FFF) 00168 00169 #define PHY_READ_TO ((uint32_t)0x0000FFFF) 00170 #define PHY_WRITE_TO ((uint32_t)0x0000FFFF) 00171 00172 /* Section 3: Common PHY Registers */ 00173 00174 #define PHY_BCR ((uint16_t)0x00) /*!< Transceiver Basic Control Register */ 00175 #define PHY_BSR ((uint16_t)0x01) /*!< Transceiver Basic Status Register */ 00176 00177 #define PHY_RESET ((uint16_t)0x8000) /*!< PHY Reset */ 00178 #define PHY_LOOPBACK ((uint16_t)0x4000) /*!< Select loop-back mode */ 00179 #define PHY_FULLDUPLEX_100M ((uint16_t)0x2100) /*!< Set the full-duplex mode at 100 Mb/s */ 00180 #define PHY_HALFDUPLEX_100M ((uint16_t)0x2000) /*!< Set the half-duplex mode at 100 Mb/s */ 00181 #define PHY_FULLDUPLEX_10M ((uint16_t)0x0100) /*!< Set the full-duplex mode at 10 Mb/s */ 00182 #define PHY_HALFDUPLEX_10M ((uint16_t)0x0000) /*!< Set the half-duplex mode at 10 Mb/s */ 00183 #define PHY_AUTONEGOTIATION ((uint16_t)0x1000) /*!< Enable auto-negotiation function */ 00184 #define PHY_RESTART_AUTONEGOTIATION ((uint16_t)0x0200) /*!< Restart auto-negotiation function */ 00185 #define PHY_POWERDOWN ((uint16_t)0x0800) /*!< Select the power down mode */ 00186 #define PHY_ISOLATE ((uint16_t)0x0400) /*!< Isolate PHY from MII */ 00187 00188 #define PHY_AUTONEGO_COMPLETE ((uint16_t)0x0020) /*!< Auto-Negotiation process completed */ 00189 #define PHY_LINKED_STATUS ((uint16_t)0x0004) /*!< Valid link established */ 00190 #define PHY_JABBER_DETECTION ((uint16_t)0x0002) /*!< Jabber condition detected */ 00191 00192 /* Section 4: Extended PHY Registers */ 00193 00194 #define PHY_SR ((uint16_t)0x10) /*!< PHY status register Offset */ 00195 #define PHY_MICR ((uint16_t)0x11) /*!< MII Interrupt Control Register */ 00196 #define PHY_MISR ((uint16_t)0x12) /*!< MII Interrupt Status and Misc. Control Register */ 00197 00198 #define PHY_LINK_STATUS ((uint16_t)0x0001) /*!< PHY Link mask */ 00199 #define PHY_SPEED_STATUS ((uint16_t)0x0002) /*!< PHY Speed mask */ 00200 #define PHY_DUPLEX_STATUS ((uint16_t)0x0004) /*!< PHY Duplex mask */ 00201 00202 #define PHY_MICR_INT_EN ((uint16_t)0x0002) /*!< PHY Enable interrupts */ 00203 #define PHY_MICR_INT_OE ((uint16_t)0x0001) /*!< PHY Enable output interrupt events */ 00204 00205 #define PHY_MISR_LINK_INT_EN ((uint16_t)0x0020) /*!< Enable Interrupt on change of link status */ 00206 #define PHY_LINK_INTERRUPT ((uint16_t)0x2000) /*!< PHY link status interrupt mask */ 00207 00208 /* Includes ------------------------------------------------------------------*/ 00209 /** 00210 * @brief Include module's header file 00211 */ 00212 00213 #ifdef HAL_RCC_MODULE_ENABLED 00214 #include "stm32f4xx_hal_rcc.h" 00215 #endif /* HAL_RCC_MODULE_ENABLED */ 00216 00217 #ifdef HAL_GPIO_MODULE_ENABLED 00218 #include "stm32f4xx_hal_gpio.h" 00219 #endif /* HAL_GPIO_MODULE_ENABLED */ 00220 00221 #ifdef HAL_DMA_MODULE_ENABLED 00222 #include "stm32f4xx_hal_dma.h" 00223 #endif /* HAL_DMA_MODULE_ENABLED */ 00224 00225 #ifdef HAL_CORTEX_MODULE_ENABLED 00226 #include "stm32f4xx_hal_cortex.h" 00227 #endif /* HAL_CORTEX_MODULE_ENABLED */ 00228 00229 #ifdef HAL_ADC_MODULE_ENABLED 00230 #include "stm32f4xx_hal_adc.h" 00231 #endif /* HAL_ADC_MODULE_ENABLED */ 00232 00233 #ifdef HAL_CAN_MODULE_ENABLED 00234 #include "stm32f4xx_hal_can.h" 00235 #endif /* HAL_CAN_MODULE_ENABLED */ 00236 00237 #ifdef HAL_CRC_MODULE_ENABLED 00238 #include "stm32f4xx_hal_crc.h" 00239 #endif /* HAL_CRC_MODULE_ENABLED */ 00240 00241 #ifdef HAL_CRYP_MODULE_ENABLED 00242 #include "stm32f4xx_hal_cryp.h" 00243 #endif /* HAL_CRYP_MODULE_ENABLED */ 00244 00245 #ifdef HAL_DMA2D_MODULE_ENABLED 00246 #include "stm32f4xx_hal_dma2d.h" 00247 #endif /* HAL_DMA2D_MODULE_ENABLED */ 00248 00249 #ifdef HAL_DAC_MODULE_ENABLED 00250 #include "stm32f4xx_hal_dac.h" 00251 #endif /* HAL_DAC_MODULE_ENABLED */ 00252 00253 #ifdef HAL_DCMI_MODULE_ENABLED 00254 #include "stm32f4xx_hal_dcmi.h" 00255 #endif /* HAL_DCMI_MODULE_ENABLED */ 00256 00257 #ifdef HAL_ETH_MODULE_ENABLED 00258 #include "stm32f4xx_hal_eth.h" 00259 #endif /* HAL_ETH_MODULE_ENABLED */ 00260 00261 #ifdef HAL_FLASH_MODULE_ENABLED 00262 #include "stm32f4xx_hal_flash.h" 00263 #endif /* HAL_FLASH_MODULE_ENABLED */ 00264 00265 #ifdef HAL_SRAM_MODULE_ENABLED 00266 #include "stm32f4xx_hal_sram.h" 00267 #endif /* HAL_SRAM_MODULE_ENABLED */ 00268 00269 #ifdef HAL_NOR_MODULE_ENABLED 00270 #include "stm32f4xx_hal_nor.h" 00271 #endif /* HAL_NOR_MODULE_ENABLED */ 00272 00273 #ifdef HAL_NAND_MODULE_ENABLED 00274 #include "stm32f4xx_hal_nand.h" 00275 #endif /* HAL_NAND_MODULE_ENABLED */ 00276 00277 #ifdef HAL_PCCARD_MODULE_ENABLED 00278 #include "stm32f4xx_hal_pccard.h" 00279 #endif /* HAL_PCCARD_MODULE_ENABLED */ 00280 00281 #ifdef HAL_SDRAM_MODULE_ENABLED 00282 #include "stm32f4xx_hal_sdram.h" 00283 #endif /* HAL_SDRAM_MODULE_ENABLED */ 00284 00285 #ifdef HAL_HASH_MODULE_ENABLED 00286 #include "stm32f4xx_hal_hash.h" 00287 #endif /* HAL_HASH_MODULE_ENABLED */ 00288 00289 #ifdef HAL_I2C_MODULE_ENABLED 00290 #include "stm32f4xx_hal_i2c.h" 00291 #endif /* HAL_I2C_MODULE_ENABLED */ 00292 00293 #ifdef HAL_I2S_MODULE_ENABLED 00294 #include "stm32f4xx_hal_i2s.h" 00295 #endif /* HAL_I2S_MODULE_ENABLED */ 00296 00297 #ifdef HAL_IWDG_MODULE_ENABLED 00298 #include "stm32f4xx_hal_iwdg.h" 00299 #endif /* HAL_IWDG_MODULE_ENABLED */ 00300 00301 #ifdef HAL_LTDC_MODULE_ENABLED 00302 #include "stm32f4xx_hal_ltdc.h" 00303 #endif /* HAL_LTDC_MODULE_ENABLED */ 00304 00305 #ifdef HAL_PWR_MODULE_ENABLED 00306 #include "stm32f4xx_hal_pwr.h" 00307 #endif /* HAL_PWR_MODULE_ENABLED */ 00308 00309 #ifdef HAL_RNG_MODULE_ENABLED 00310 #include "stm32f4xx_hal_rng.h" 00311 #endif /* HAL_RNG_MODULE_ENABLED */ 00312 00313 #ifdef HAL_RTC_MODULE_ENABLED 00314 #include "stm32f4xx_hal_rtc.h" 00315 #endif /* HAL_RTC_MODULE_ENABLED */ 00316 00317 #ifdef HAL_SAI_MODULE_ENABLED 00318 #include "stm32f4xx_hal_sai.h" 00319 #endif /* HAL_SAI_MODULE_ENABLED */ 00320 00321 #ifdef HAL_SD_MODULE_ENABLED 00322 #include "stm32f4xx_hal_sd.h" 00323 #endif /* HAL_SD_MODULE_ENABLED */ 00324 00325 #ifdef HAL_SPI_MODULE_ENABLED 00326 #include "stm32f4xx_hal_spi.h" 00327 #endif /* HAL_SPI_MODULE_ENABLED */ 00328 00329 #ifdef HAL_TIM_MODULE_ENABLED 00330 #include "stm32f4xx_hal_tim.h" 00331 #endif /* HAL_TIM_MODULE_ENABLED */ 00332 00333 #ifdef HAL_UART_MODULE_ENABLED 00334 #include "stm32f4xx_hal_uart.h" 00335 #endif /* HAL_UART_MODULE_ENABLED */ 00336 00337 #ifdef HAL_USART_MODULE_ENABLED 00338 #include "stm32f4xx_hal_usart.h" 00339 #endif /* HAL_USART_MODULE_ENABLED */ 00340 00341 #ifdef HAL_IRDA_MODULE_ENABLED 00342 #include "stm32f4xx_hal_irda.h" 00343 #endif /* HAL_IRDA_MODULE_ENABLED */ 00344 00345 #ifdef HAL_SMARTCARD_MODULE_ENABLED 00346 #include "stm32f4xx_hal_smartcard.h" 00347 #endif /* HAL_SMARTCARD_MODULE_ENABLED */ 00348 00349 #ifdef HAL_WWDG_MODULE_ENABLED 00350 #include "stm32f4xx_hal_wwdg.h" 00351 #endif /* HAL_WWDG_MODULE_ENABLED */ 00352 00353 #ifdef HAL_PCD_MODULE_ENABLED 00354 #include "stm32f4xx_hal_pcd.h" 00355 #endif /* HAL_PCD_MODULE_ENABLED */ 00356 00357 #ifdef HAL_HCD_MODULE_ENABLED 00358 #include "stm32f4xx_hal_hcd.h" 00359 #endif /* HAL_HCD_MODULE_ENABLED */ 00360 00361 /* Exported macro ------------------------------------------------------------*/ 00362 #ifdef USE_FULL_ASSERT 00363 /** 00364 * @brief The assert_param macro is used for function's parameters check. 00365 * @param expr: If expr is false, it calls assert_failed function 00366 * which reports the name of the source file and the source 00367 * line number of the call that failed. 00368 * If expr is true, it returns no value. 00369 * @retval None 00370 */ 00371 #define assert_param(expr) ((expr) ? (void)0 : assert_failed((uint8_t *)__FILE__, __LINE__)) 00372 /* Exported functions ------------------------------------------------------- */ 00373 void assert_failed(uint8_t* file, uint32_t line); 00374 #else 00375 #define assert_param(expr) ((void)0) 00376 #endif /* USE_FULL_ASSERT */ 00377 00378 #ifdef __cplusplus 00379 } 00380 #endif 00381 00382 #endif /* __STM32F4xx_HAL_CONF_H */ 00383 00384 00385 /************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ 00386 00387
Generated on Wed Jul 13 2022 10:27:32 by 1.7.2