Diff: UbloxCellularDriverGen.cpp

Revision:

5:b935404dcf7c

Parent:

4:4f2c12992e17

Child:

7:a9eea2dbdd68

diff -r 4f2c12992e17 -r b935404dcf7c UbloxCellularDriverGen.cpp
--- a/UbloxCellularDriverGen.cpp	Tue Jun 13 10:45:14 2017 +0100
+++ b/UbloxCellularDriverGen.cpp	Thu Jun 15 01:14:18 2017 +0100
@@ -90,7 +90,7 @@
     // +CCWA: <status>[, <class>]
     numChars = read_at_to_char(buf, sizeof (buf), '\n');
     if (numChars > 0) {
-        if (sscanf(buf, ": %d, %d", &a, &b) > 0) {
+        if (sscanf(buf, ": %d,%d", &a, &b) > 0) {
             if (_ssUrcBuf == NULL) {
                 _ssUrcBuf = (char *) malloc(numChars + 5 + 1);
                 if (_ssUrcBuf != NULL) {
@@ -413,7 +413,7 @@
     // by +CMT, should it ever occur
     _at->oob("+CMTI:", callback(this, &UbloxCellularDriverGen::CMTI_URC));
 
-    // URCs relater to supplementary services
+    // URCs related to supplementary services
     _at->oob("+CCWA", callback(this, &UbloxCellularDriverGen::CCWA_URC));
     _at->oob("+CCFC", callback(this, &UbloxCellularDriverGen::CCFC_URC));
     _at->oob("+CLIR", callback(this, &UbloxCellularDriverGen::CLIR_URC));
@@ -554,12 +554,12 @@
                 // Wait for either +CUSD to come back or
                 // one of the other SS related URCs to trigger
                 if (_ssUrcBuf != NULL) {
-                    free (_ssUrcBuf);
+                    free(_ssUrcBuf);
                     _ssUrcBuf = NULL;
                 }
                 timer.start();
                 _at->set_timeout(1000);
-                while (!success && (timer.read_ms() < atTimeout)) {
+                while (!success && (timer.read_ms() < 30000)) {
                     if (_at->recv("+CUSD: %*d,\"")) {
                         // Note: don't wait for "OK" here as the +CUSD response may come
                         // before or after the OK
@@ -641,6 +641,7 @@
     int blockSize = FILE_BUFFER_SIZE;
     char respFilename[48 + 1];
     int sz, sz_read;
+    char * endQuote;
     bool success = true;
     int ch = 0;
     int timeLimit;
@@ -664,34 +665,46 @@
 
             if (blockSize > 0) {
                 if (_at->send("AT+URDBLOCK=\"%s\",%d,%d\r\n", filename, offset, blockSize) &&
-                    _at->recv("+URDBLOCK: \"%48[^\"]\",%d,\"", respFilename, &sz) &&
-                    (strcmp(filename, respFilename) == 0)) {
+                    _at->recv("+URDBLOCK: %48[^,],%d,\"", respFilename, &sz)) {
+                    // On some modules the response filename is not in quotes,
+                    // on others it is, so strip them here
+                    if ((*respFilename == '"') && ((endQuote = strchr(respFilename + 1, '"')) != NULL)) {
+                        memcpy (respFilename, respFilename + 1, endQuote - respFilename - 1);
+                        *(endQuote - 1) = 0;
+                    }
+                    if (strcmp(filename, respFilename) == 0) {
+                        // Would use _at->read() here, but if it runs ahead of the
+                        // serial stream it returns -1 instead of the number of characters
+                        // read so far, which is not very helpful so instead use _at->getc() and
+                        // a time limit. The time limit is three times the amount of time it
+                        // should take to read the block at the working baud rate with a minimum
+                        // of 10 ms (for short files)
+                        timer.reset();
+                        timer.start();
+                        timeLimit = blockSize * 3 / ((MBED_CONF_UBLOX_CELL_BAUD_RATE / 8) / 1000);
+                        if (timeLimit < 10) {
+                            timeLimit = 10;
+                        }
+                        sz_read = 0;
+                        while ((sz_read < blockSize) && (timer.read_ms() < timeLimit)) {
+                            ch = _at->getc();
+                            if (ch >= 0) {
+                                *buf = ch;
+                                buf++;
+                                sz_read++;
+                            }
+                        }
+                        timer.stop();
 
-                    // Would use _at->read() here, but if it runs ahead of the
-                    // serial stream it returns -1 instead of the number of characters
-                    // read so far, which is not very helpful so instead use _at->getc() and
-                    // a time limit. The time limit is twice the amount of time it should take to
-                    // read the block at the working baud rate
-                    timer.reset();
-                    timer.start();
-                    timeLimit = blockSize * 2 / ((MBED_CONF_UBLOX_CELL_BAUD_RATE / 8) / 1000);
-                    sz_read = 0;
-                    while ((sz_read < blockSize) && (timer.read_ms() < timeLimit)) {
-                        ch = _at->getc();
-                        if (ch >= 0) {
-                            *buf = ch;
-                            buf++;
-                            sz_read++;
+                        if (sz_read == blockSize) {
+                            bytesToRead -= sz_read;
+                            offset += sz_read;
+                            _at->recv("OK");
+                        } else {
+                        debug_if(_debug_trace_on, "blockSize %d but only received %d bytes\n", blockSize, sz_read);
+                            success = false;
                         }
-                    }
-                    timer.stop();
-
-                    if (sz_read == blockSize) {
-                        bytesToRead -= sz_read;
-                        offset += sz_read;
-                        _at->recv("OK");
                     } else {
-                        debug_if(_debug_trace_on, "blockSize %d but only received %d bytes\n", blockSize, sz_read);
                         success = false;
                     }
                } else {