An I/O controller for virtual pinball machines: accelerometer nudge sensing, analog plunger input, button input encoding, LedWiz compatible output controls, and more.

Dependencies:   mbed FastIO FastPWM USBDevice

Fork of Pinscape_Controller by Mike R

/media/uploads/mjr/pinscape_no_background_small_L7Miwr6.jpg

This is Version 2 of the Pinscape Controller, an I/O controller for virtual pinball machines. (You can find the old version 1 software here.) Pinscape is software for the KL25Z that turns the board into a full-featured I/O controller for virtual pinball, with support for accelerometer-based nudging, a real plunger, button inputs, and feedback device control.

In case you haven't heard of the concept before, a "virtual pinball machine" is basically a video pinball simulator that's built into a real pinball machine body. A TV monitor goes in place of the pinball playfield, and a second TV goes in the backbox to serve as the "backglass" display. A third smaller monitor can serve as the "DMD" (the Dot Matrix Display used for scoring on newer machines), or you can even install a real pinball plasma DMD. A computer is hidden inside the cabinet, running pinball emulation software that displays a life-sized playfield on the main TV. The cabinet has all of the usual buttons, too, so it not only looks like the real thing, but plays like it too. That's a picture of my own machine to the right. On the outside, it's built exactly like a real arcade pinball machine, with the same overall dimensions and all of the standard pinball cabinet hardware.

A few small companies build and sell complete, finished virtual pinball machines, but I think it's more fun as a DIY project. If you have some basic wood-working skills and know your way around PCs, you can build one from scratch. The computer part is just an ordinary Windows PC, and all of the pinball emulation can be built out of free, open-source software. In that spirit, the Pinscape Controller is an open-source software/hardware project that offers a no-compromises, all-in-one control center for all of the unique input/output needs of a virtual pinball cabinet. If you've been thinking about building one of these, but you're not sure how to connect a plunger, flipper buttons, lights, nudge sensor, and whatever else you can think of, this project might be just what you're looking for.

You can find much more information about DIY Pin Cab building in general in the Virtual Cabinet Forum on vpforums.org. Also visit my Pinscape Resources page for more about this project and other virtual pinball projects I'm working on.

Downloads

  • Pinscape Release Builds: This page has download links for all of the Pinscape software. To get started, install and run the Pinscape Config Tool on your Windows computer. It will lead you through the steps for installing the Pinscape firmware on the KL25Z.
  • Config Tool Source Code. The complete C# source code for the config tool. You don't need this to run the tool, but it's available if you want to customize anything or see how it works inside.

Documentation

The new Version 2 Build Guide is now complete! This new version aims to be a complete guide to building a virtual pinball machine, including not only the Pinscape elements but all of the basics, from sourcing parts to building all of the hardware.

You can also refer to the original Hardware Build Guide (PDF), but that's out of date now, since it refers to the old version 1 software, which was rather different (especially when it comes to configuration).

System Requirements

The new config tool requires a fairly up-to-date Microsoft .NET installation. If you use Windows Update to keep your system current, you should be fine. A modern version of Internet Explorer (IE) is required, even if you don't use it as your main browser, because the config tool uses some system components that Microsoft packages into the IE install set. I test with IE11, so that's known to work. IE8 doesn't work. IE9 and 10 are unknown at this point.

The Windows requirements are only for the config tool. The firmware doesn't care about anything on the Windows side, so if you can make do without the config tool, you can use almost any Windows setup.

Main Features

Plunger: The Pinscape Controller started out as a "mechanical plunger" controller: a device for attaching a real pinball plunger to the video game software so that you could launch the ball the natural way. This is still, of course, a central feature of the project. The software supports several types of sensors: a high-resolution optical sensor (which works by essentially taking pictures of the plunger as it moves); a slide potentionmeter (which determines the position via the changing electrical resistance in the pot); a quadrature sensor (which counts bars printed on a special guide rail that it moves along); and an IR distance sensor (which determines the position by sending pulses of light at the plunger and measuring the round-trip travel time). The Build Guide explains how to set up each type of sensor.

Nudging: The KL25Z (the little microcontroller that the software runs on) has a built-in accelerometer. The Pinscape software uses it to sense when you nudge the cabinet, and feeds the acceleration data to the pinball software on the PC. This turns physical nudges into virtual English on the ball. The accelerometer is quite sensitive and accurate, so we can measure the difference between little bumps and hard shoves, and everything in between. The result is natural and immersive.

Buttons: You can wire real pinball buttons to the KL25Z, and the software will translate the buttons into PC input. You have the option to map each button to a keyboard key or joystick button. You can wire up your flipper buttons, Magna Save buttons, Start button, coin slots, operator buttons, and whatever else you need.

Feedback devices: You can also attach "feedback devices" to the KL25Z. Feedback devices are things that create tactile, sound, and lighting effects in sync with the game action. The most popular PC pinball emulators know how to address a wide variety of these devices, and know how to match them to on-screen action in each virtual table. You just need an I/O controller that translates commands from the PC into electrical signals that turn the devices on and off. The Pinscape Controller can do that for you.

Expansion Boards

There are two main ways to run the Pinscape Controller: standalone, or using the "expansion boards".

In the basic standalone setup, you just need the KL25Z, plus whatever buttons, sensors, and feedback devices you want to attach to it. This mode lets you take advantage of everything the software can do, but for some features, you'll have to build some ad hoc external circuitry to interface external devices with the KL25Z. The Build Guide has detailed plans for exactly what you need to build.

The other option is the Pinscape Expansion Boards. The expansion boards are a companion project, which is also totally free and open-source, that provides Printed Circuit Board (PCB) layouts that are designed specifically to work with the Pinscape software. The PCB designs are in the widely used EAGLE format, which many PCB manufacturers can turn directly into physical boards for you. The expansion boards organize all of the external connections more neatly than on the standalone KL25Z, and they add all of the interface circuitry needed for all of the advanced software functions. The big thing they bring to the table is lots of high-power outputs. The boards provide a modular system that lets you add boards to add more outputs. If you opt for the basic core setup, you'll have enough outputs for all of the toys in a really well-equipped cabinet. If your ambitions go beyond merely well-equipped and run to the ridiculously extravagant, just add an extra board or two. The modular design also means that you can add to the system over time.

Expansion Board project page

Update notes

If you have a Pinscape V1 setup already installed, you should be able to switch to the new version pretty seamlessly. There are just a couple of things to be aware of.

First, the "configuration" procedure is completely different in the new version. Way better and way easier, but it's not what you're used to from V1. In V1, you had to edit the project source code and compile your own custom version of the program. No more! With V2, you simply install the standard, pre-compiled .bin file, and select options using the Pinscape Config Tool on Windows.

Second, if you're using the TSL1410R optical sensor for your plunger, there's a chance you'll need to boost your light source's brightness a little bit. The "shutter speed" is faster in this version, which means that it doesn't spend as much time collecting light per frame as before. The software actually does "auto exposure" adaptation on every frame, so the increased shutter speed really shouldn't bother it, but it does require a certain minimum level of contrast, which requires a certain minimal level of lighting. Check the plunger viewer in the setup tool if you have any problems; if the image looks totally dark, try increasing the light level to see if that helps.

New Features

V2 has numerous new features. Here are some of the highlights...

Dynamic configuration: as explained above, configuration is now handled through the Config Tool on Windows. It's no longer necessary to edit the source code or compile your own modified binary.

Improved plunger sensing: the software now reads the TSL1410R optical sensor about 15x faster than it did before. This allows reading the sensor at full resolution (400dpi), about 400 times per second. The faster frame rate makes a big difference in how accurately we can read the plunger position during the fast motion of a release, which allows for more precise position sensing and faster response. The differences aren't dramatic, since the sensing was already pretty good even with the slower V1 scan rate, but you might notice a little better precision in tricky skill shots.

Keyboard keys: button inputs can now be mapped to keyboard keys. The joystick button option is still available as well, of course. Keyboard keys have the advantage of being closer to universal for PC pinball software: some pinball software can be set up to take joystick input, but nearly all PC pinball emulators can take keyboard input, and nearly all of them use the same key mappings.

Local shift button: one physical button can be designed as the local shift button. This works like a Shift button on a keyboard, but with cabinet buttons. It allows each physical button on the cabinet to have two PC keys assigned, one normal and one shifted. Hold down the local shift button, then press another key, and the other key's shifted key mapping is sent to the PC. The shift button can have a regular key mapping of its own as well, so it can do double duty. The shift feature lets you access more functions without cluttering your cabinet with extra buttons. It's especially nice for less frequently used functions like adjusting the volume or activating night mode.

Night mode: the output controller has a new "night mode" option, which lets you turn off all of your noisy devices with a single button, switch, or PC command. You can designate individual ports as noisy or not. Night mode only disables the noisemakers, so you still get the benefit of your flashers, button lights, and other quiet devices. This lets you play late into the night without disturbing your housemates or neighbors.

Gamma correction: you can designate individual output ports for gamma correction. This adjusts the intensity level of an output to make it match the way the human eye perceives brightness, so that fades and color mixes look more natural in lighting devices. You can apply this to individual ports, so that it only affects ports that actually have lights of some kind attached.

IR Remote Control: the controller software can transmit and/or receive IR remote control commands if you attach appropriate parts (an IR LED to send, an IR sensor chip to receive). This can be used to turn on your TV(s) when the system powers on, if they don't turn on automatically, and for any other functions you can think of requiring IR send/receive capabilities. You can assign IR commands to cabinet buttons, so that pressing a button on your cabinet sends a remote control command from the attached IR LED, and you can have the controller generate virtual key presses on your PC in response to received IR commands. If you have the IR sensor attached, the system can use it to learn commands from your existing remotes.

Yet more USB fixes: I've been gradually finding and fixing USB bugs in the mbed library for months now. This version has all of the fixes of the last couple of releases, of course, plus some new ones. It also has a new "last resort" feature, since there always seems to be "just one more" USB bug. The last resort is that you can tell the device to automatically reboot itself if it loses the USB connection and can't restore it within a given time limit.

More Downloads

  • Custom VP builds: I created modified versions of Visual Pinball 9.9 and Physmod5 that you might want to use in combination with this controller. The modified versions have special handling for plunger calibration specific to the Pinscape Controller, as well as some enhancements to the nudge physics. If you're not using the plunger, you might still want it for the nudge improvements. The modified version also works with any other input controller, so you can get the enhanced nudging effects even if you're using a different plunger/nudge kit. The big change in the modified versions is a "filter" for accelerometer input that's designed to make the response to cabinet nudges more realistic. It also makes the response more subdued than in the standard VP, so it's not to everyone's taste. The downloads include both the updated executables and the source code changes, in case you want to merge the changes into your own custom version(s).

    Note! These features are now standard in the official VP releases, so you don't need my custom builds if you're using 9.9.1 or later and/or VP 10. I don't think there's any reason to use my versions instead of the latest official ones, and in fact I'd encourage you to use the official releases since they're more up to date, but I'm leaving my builds available just in case. In the official versions, look for the checkbox "Enable Nudge Filter" in the Keys preferences dialog. My custom versions don't include that checkbox; they just enable the filter unconditionally.
  • Output circuit shopping list: This is a saved shopping cart at mouser.com with the parts needed to build one copy of the high-power output circuit for the LedWiz emulator feature, for use with the standalone KL25Z (that is, without the expansion boards). The quantities in the cart are for one output channel, so if you want N outputs, simply multiply the quantities by the N, with one exception: you only need one ULN2803 transistor array chip for each eight output circuits. If you're using the expansion boards, you won't need any of this, since the boards provide their own high-power outputs.
  • Cary Owens' optical sensor housing: A 3D-printable design for a housing/mounting bracket for the optical plunger sensor, designed by Cary Owens. This makes it easy to mount the sensor.
  • Lemming77's potentiometer mounting bracket and shooter rod connecter: Sketchup designs for 3D-printable parts for mounting a slide potentiometer as the plunger sensor. These were designed for a particular slide potentiometer that used to be available from an Aliexpress.com seller but is no longer listed. You can probably use this design as a starting point for other similar devices; just check the dimensions before committing the design to plastic.

Copyright and License

The Pinscape firmware is copyright 2014, 2021 by Michael J Roberts. It's released under an MIT open-source license. See License.

Warning to VirtuaPin Kit Owners

This software isn't designed as a replacement for the VirtuaPin plunger kit's firmware. If you bought the VirtuaPin kit, I recommend that you don't install this software. The VirtuaPin kit uses the same KL25Z microcontroller that Pinscape uses, but the rest of its hardware is different and incompatible. In particular, the Pinscape firmware doesn't include support for the IR proximity sensor used in the VirtuaPin plunger kit, so you won't be able to use your plunger device with the Pinscape firmware. In addition, the VirtuaPin setup uses a different set of GPIO pins for the button inputs from the Pinscape defaults, so if you do install the Pinscape firmware, you'll have to go into the Config Tool and reassign all of the buttons to match the VirtuaPin wiring.

Committer:
mjr
Date:
Wed Jun 03 18:52:22 2015 +0000
Revision:
24:e902bc7cdc1e
Parent:
23:14f8c5004cd0
Child:
25:e22b88bd783a
Restored CCD sensor as the default sensor in config.h

Who changed what in which revision?

UserRevisionLine numberNew contents of line
mjr 17:ab3cec0c8bf4 1 // Pinscape Controller Configuration
mjr 17:ab3cec0c8bf4 2 //
mjr 17:ab3cec0c8bf4 3 // To customize your private configuration, simply open this file in the
mjr 17:ab3cec0c8bf4 4 // mbed on-line IDE, make your changes, save the file, and click the Compile
mjr 17:ab3cec0c8bf4 5 // button at the top of the window. That will generate a customized .bin
mjr 17:ab3cec0c8bf4 6 // file that you can download onto your KL25Z board.
mjr 17:ab3cec0c8bf4 7
mjr 17:ab3cec0c8bf4 8
mjr 17:ab3cec0c8bf4 9 // --------------------------------------------------------------------------
mjr 21:5048e16cc9ef 10 //
mjr 21:5048e16cc9ef 11 // Enable/disable joystick functions.
mjr 21:5048e16cc9ef 12 //
mjr 21:5048e16cc9ef 13 // This controls whether or not we send joystick reports to the PC with the
mjr 21:5048e16cc9ef 14 // plunger and accelerometer readings. By default, this is enabled. If
mjr 21:5048e16cc9ef 15 // you want to use two or more physical KL25Z Pinscape controllers in your
mjr 21:5048e16cc9ef 16 // system (e.g., if you want to increase the number of output ports
mjr 21:5048e16cc9ef 17 // available by using two or more KL25Z's), you should disable the joystick
mjr 21:5048e16cc9ef 18 // features on the second (and third+) controller. It's not useful to have
mjr 21:5048e16cc9ef 19 // more than one board reporting the accelerometer readings to the host -
mjr 21:5048e16cc9ef 20 // doing so will just add USB overhead. This setting lets you turn off the
mjr 21:5048e16cc9ef 21 // reports for the secondary controllers, turning the secondary boards into
mjr 21:5048e16cc9ef 22 // output-only devices.
mjr 21:5048e16cc9ef 23 //
mjr 21:5048e16cc9ef 24 // Note that you can't use button inputs on a controller that has the
mjr 21:5048e16cc9ef 25 // joystick features disabled, because the buttons are handled via the
mjr 21:5048e16cc9ef 26 // joystick reports. Wire all of your buttons to the primary KL25Z that
mjr 21:5048e16cc9ef 27 // has the joystick features enabled.
mjr 21:5048e16cc9ef 28 //
mjr 21:5048e16cc9ef 29 // To disable the joystick features, just comment out the next line (add
mjr 21:5048e16cc9ef 30 // two slashes at the beginning of the line).
mjr 21:5048e16cc9ef 31 //
mjr 21:5048e16cc9ef 32 #define ENABLE_JOYSTICK
mjr 21:5048e16cc9ef 33
mjr 21:5048e16cc9ef 34
mjr 21:5048e16cc9ef 35 // --------------------------------------------------------------------------
mjr 17:ab3cec0c8bf4 36 //
mjr 17:ab3cec0c8bf4 37 // LedWiz default unit number.
mjr 17:ab3cec0c8bf4 38 //
mjr 21:5048e16cc9ef 39 // Each LedWiz device has a unit number, from 1 to 16. This lets you install
mjr 17:ab3cec0c8bf4 40 // more than one LedWiz in your system: as long as each one has a different
mjr 17:ab3cec0c8bf4 41 // unit number, the software on the PC can tell them apart and route commands
mjr 17:ab3cec0c8bf4 42 // to the right device.
mjr 17:ab3cec0c8bf4 43 //
mjr 21:5048e16cc9ef 44 // A *real* LedWiz has its unit number set at the factory; they set it to
mjr 21:5048e16cc9ef 45 // unit 1 unless you specifically request a different number when you place
mjr 21:5048e16cc9ef 46 // your order.
mjr 21:5048e16cc9ef 47 //
mjr 21:5048e16cc9ef 48 // For our *emulated* LedWiz, we default to unit #8. However, if we're set
mjr 21:5048e16cc9ef 49 // up as a secondary Pinscape controller with the joystick functions turned
mjr 21:5048e16cc9ef 50 // off, we'll use unit #9 instead.
mjr 17:ab3cec0c8bf4 51 //
mjr 21:5048e16cc9ef 52 // The reason we start at unit #8 is that we want to avoid conflicting with
mjr 21:5048e16cc9ef 53 // any real LedWiz devices you have in your system. If you have a real
mjr 21:5048e16cc9ef 54 // LedWiz, it's probably unit #1, since that's the standard factor setting.
mjr 21:5048e16cc9ef 55 // If you have two real LedWiz's, they're probably units #1 and #2. If you
mjr 21:5048e16cc9ef 56 // have three... well, I don't think anyone actually has three, but if you
mjr 21:5048e16cc9ef 57 // did it would probably be unit #3. And so on. That's why we start at #8 -
mjr 21:5048e16cc9ef 58 // it seems really unlikely that this will conflict with anybody's existing
mjr 21:5048e16cc9ef 59 // setup. On the off chance it does, simply change the setting here to a
mjr 21:5048e16cc9ef 60 // different unit number that's not already used in your system.
mjr 17:ab3cec0c8bf4 61 //
mjr 21:5048e16cc9ef 62 // Note 1: the unit number here is the *user visible* unit number that
mjr 21:5048e16cc9ef 63 // you use on the PC side. It's the number you specify in your DOF
mjr 21:5048e16cc9ef 64 // configuration and so forth. Internally, the USB reports subtract
mjr 21:5048e16cc9ef 65 // one from this number - e.g., nominal unit #1 shows up as 0 in the USB
mjr 21:5048e16cc9ef 66 // reports. If you're trying to puzzle out why all of the USB reports
mjr 21:5048e16cc9ef 67 // are all off by one from the unit number you select here, that's why.
mjr 17:ab3cec0c8bf4 68 //
mjr 17:ab3cec0c8bf4 69 // Note 2: the DOF Configtool (google it) knows about the Pinscape
mjr 21:5048e16cc9ef 70 // controller (it's known there as just a "KL25Z" rather than Pinscape).
mjr 21:5048e16cc9ef 71 // And the DOF tool knows that it uses #8 as its default unit number, so
mjr 21:5048e16cc9ef 72 // it names the .ini file for this controller xxx8.ini. If you change the
mjr 21:5048e16cc9ef 73 // unit number here, remember to rename the DOF-generated .ini file to
mjr 21:5048e16cc9ef 74 // match, by changing the "8" at the end of the filename to the new number
mjr 21:5048e16cc9ef 75 // you set here.
mjr 21:5048e16cc9ef 76 const uint8_t DEFAULT_LEDWIZ_UNIT_NUMBER =
mjr 21:5048e16cc9ef 77 #ifdef ENABLE_JOYSTICK
mjr 21:5048e16cc9ef 78 0x08; // joystick enabled - assume we're the primary KL25Z, so use unit #8
mjr 21:5048e16cc9ef 79 #else
mjr 21:5048e16cc9ef 80 0x09; // joystick disabled - assume we're a secondary, output-only KL25Z, so use #9
mjr 21:5048e16cc9ef 81 #endif
mjr 17:ab3cec0c8bf4 82
mjr 17:ab3cec0c8bf4 83 // --------------------------------------------------------------------------
mjr 17:ab3cec0c8bf4 84 //
mjr 17:ab3cec0c8bf4 85 // Plunger CCD sensor.
mjr 17:ab3cec0c8bf4 86 //
mjr 17:ab3cec0c8bf4 87 // If you're NOT using the CCD sensor, comment out the next line (by adding
mjr 17:ab3cec0c8bf4 88 // two slashes at the start of the line).
mjr 17:ab3cec0c8bf4 89
mjr 24:e902bc7cdc1e 90 #define ENABLE_CCD_SENSOR
mjr 17:ab3cec0c8bf4 91
mjr 17:ab3cec0c8bf4 92 // The KL25Z pins that the CCD sensor is physically attached to:
mjr 17:ab3cec0c8bf4 93 //
mjr 17:ab3cec0c8bf4 94 // CCD_SI_PIN = the SI (sensor data input) pin
mjr 17:ab3cec0c8bf4 95 // CCD_CLOCK_PIN = the sensor clock pin
mjr 17:ab3cec0c8bf4 96 // CCD_SO_PIN = the SO (sensor data output) pin
mjr 17:ab3cec0c8bf4 97 //
mjr 17:ab3cec0c8bf4 98 // The SI an Clock pins are DigitalOut pins, so these can be set to just
mjr 17:ab3cec0c8bf4 99 // about any gpio pins that aren't used for something else. The SO pin must
mjr 17:ab3cec0c8bf4 100 // be an AnalogIn capable pin - only a few of the KL25Z gpio pins qualify,
mjr 17:ab3cec0c8bf4 101 // so check the pinout diagram to find suitable candidates if you need to
mjr 17:ab3cec0c8bf4 102 // change this. Note that some of the gpio pins shown in the mbed pinout
mjr 17:ab3cec0c8bf4 103 // diagrams are committed to other uses by the mbed software or by the KL25Z
mjr 17:ab3cec0c8bf4 104 // wiring itself, so if you do change these, be sure that the new pins you
mjr 17:ab3cec0c8bf4 105 // select are really available.
mjr 17:ab3cec0c8bf4 106
mjr 17:ab3cec0c8bf4 107 const PinName CCD_SI_PIN = PTE20;
mjr 17:ab3cec0c8bf4 108 const PinName CCD_CLOCK_PIN = PTE21;
mjr 17:ab3cec0c8bf4 109 const PinName CCD_SO_PIN = PTB0;
mjr 17:ab3cec0c8bf4 110
mjr 17:ab3cec0c8bf4 111 // --------------------------------------------------------------------------
mjr 17:ab3cec0c8bf4 112 //
mjr 17:ab3cec0c8bf4 113 // Plunger potentiometer sensor.
mjr 17:ab3cec0c8bf4 114 //
mjr 23:14f8c5004cd0 115 // If you're using a potentiometer as the plunger sensor, un-comment the
mjr 23:14f8c5004cd0 116 // next line (by removing the two slashes at the start of the line), and
mjr 23:14f8c5004cd0 117 // also comment out the ENABLE_CCD_SENSOR line above.
mjr 17:ab3cec0c8bf4 118
mjr 24:e902bc7cdc1e 119 //#define ENABLE_POT_SENSOR
mjr 17:ab3cec0c8bf4 120
mjr 23:14f8c5004cd0 121 // The KL25Z pin that your potentiometer is attached to. The potentiometer
mjr 23:14f8c5004cd0 122 // requires wiring three connectins:
mjr 23:14f8c5004cd0 123 //
mjr 23:14f8c5004cd0 124 // - Wire the fixed resistance end of the potentiometer nearest the KNOB
mjr 23:14f8c5004cd0 125 // end of the plunger to the 3.3V output from the KL25Z
mjr 23:14f8c5004cd0 126 //
mjr 23:14f8c5004cd0 127 // - Wire the other fixed resistance end to KL25Z Ground
mjr 23:14f8c5004cd0 128 //
mjr 23:14f8c5004cd0 129 // - Wire the potentiometer wiper (the variable output terminal) to the
mjr 23:14f8c5004cd0 130 // KL25Z pin identified below.
mjr 23:14f8c5004cd0 131 //
mjr 23:14f8c5004cd0 132 // Note that you can change the pin selection below, but if you do, the new
mjr 23:14f8c5004cd0 133 // pin must be AnalogIn capable. Only a few of the KL25Z pins qualify. Refer
mjr 23:14f8c5004cd0 134 // to the KL25Z pinout diagram to find another AnalogIn pin if you need to
mjr 23:14f8c5004cd0 135 // change this for any reason. Note that the default is to use the same analog
mjr 23:14f8c5004cd0 136 // input that the CCD sensor would use if it were enabled, which is why you
mjr 23:14f8c5004cd0 137 // have to be sure to disable the CCD support in the software if you're using
mjr 23:14f8c5004cd0 138 // a potentiometer as the sensor.
mjr 17:ab3cec0c8bf4 139
mjr 17:ab3cec0c8bf4 140 const PinName POT_PIN = PTB0;
mjr 17:ab3cec0c8bf4 141
mjr 17:ab3cec0c8bf4 142 // --------------------------------------------------------------------------
mjr 17:ab3cec0c8bf4 143 //
mjr 17:ab3cec0c8bf4 144 // Plunger calibration button and indicator light.
mjr 17:ab3cec0c8bf4 145 //
mjr 17:ab3cec0c8bf4 146 // These specify the pin names of the plunger calibration button connections.
mjr 17:ab3cec0c8bf4 147 // If you're not using these, you can set these to NC. (You can even use the
mjr 17:ab3cec0c8bf4 148 // button but not the LED; set the LED to NC if you're only using the button.)
mjr 17:ab3cec0c8bf4 149 //
mjr 17:ab3cec0c8bf4 150 // If you're using the button, wire one terminal of a momentary switch or
mjr 17:ab3cec0c8bf4 151 // pushbutton to the input pin you select, and wire the other terminal to the
mjr 17:ab3cec0c8bf4 152 // KL25Z ground. Push and hold the button for a few seconds to enter plunger
mjr 17:ab3cec0c8bf4 153 // calibration mode.
mjr 17:ab3cec0c8bf4 154 //
mjr 17:ab3cec0c8bf4 155 // If you're using the LED, you'll need to build a little transistor power
mjr 17:ab3cec0c8bf4 156 // booster circuit to power the LED, as described in the build guide. The
mjr 17:ab3cec0c8bf4 157 // LED gives you visual confirmation that the you've triggered calibration
mjr 17:ab3cec0c8bf4 158 // mode and lets you know when the mode times out. Note that the LED on
mjr 17:ab3cec0c8bf4 159 // board the KL25Z also changes color to indicate the same information, so
mjr 17:ab3cec0c8bf4 160 // if the KL25Z is positioned so that you can see it while you're doing the
mjr 17:ab3cec0c8bf4 161 // calibration, you don't really need a separate button LED. But the
mjr 17:ab3cec0c8bf4 162 // separate LED is spiffy, especially if it's embedded in the pushbutton.
mjr 17:ab3cec0c8bf4 163 //
mjr 17:ab3cec0c8bf4 164 // Note that you can skip the pushbutton altogether and trigger calibration
mjr 17:ab3cec0c8bf4 165 // from the Windows control software. But again, the button is spiffier.
mjr 17:ab3cec0c8bf4 166
mjr 17:ab3cec0c8bf4 167 // calibration button input
mjr 17:ab3cec0c8bf4 168 const PinName CAL_BUTTON_PIN = PTE29;
mjr 17:ab3cec0c8bf4 169
mjr 17:ab3cec0c8bf4 170 // calibration button indicator LED
mjr 17:ab3cec0c8bf4 171 const PinName CAL_BUTTON_LED = PTE23;
mjr 17:ab3cec0c8bf4 172
mjr 17:ab3cec0c8bf4 173
mjr 17:ab3cec0c8bf4 174 // --------------------------------------------------------------------------
mjr 17:ab3cec0c8bf4 175 //
mjr 17:ab3cec0c8bf4 176 // Pseudo "Launch Ball" button.
mjr 17:ab3cec0c8bf4 177 //
mjr 17:ab3cec0c8bf4 178 // Zeb of zebsboards.com came up with a clever scheme for his plunger kit
mjr 17:ab3cec0c8bf4 179 // that lets the plunger simulate a Launch Ball button for tables where
mjr 17:ab3cec0c8bf4 180 // the original used a Launch button instead of a plunger (e.g., Medieval
mjr 17:ab3cec0c8bf4 181 // Madness, T2, or Star Trek: The Next Generation). The scheme uses an
mjr 17:ab3cec0c8bf4 182 // LedWiz output to tell us when such a table is loaded. On the DOF
mjr 17:ab3cec0c8bf4 183 // Configtool site, this is called "ZB Launch Ball". When this LedWiz
mjr 17:ab3cec0c8bf4 184 // output is ON, it tells us that the table will ignore the analog plunger
mjr 17:ab3cec0c8bf4 185 // because it doesn't have a plunger object, so the analog plunger should
mjr 17:ab3cec0c8bf4 186 // send a Launch Ball button press signal when the user releases the plunger.
mjr 17:ab3cec0c8bf4 187 //
mjr 17:ab3cec0c8bf4 188 // If you wish to use this feature, you need to do two things:
mjr 17:ab3cec0c8bf4 189 //
mjr 17:ab3cec0c8bf4 190 // First, adjust the two lines below to set the LedWiz output and joystick
mjr 17:ab3cec0c8bf4 191 // button you wish to use for this feature. The defaults below should be
mjr 17:ab3cec0c8bf4 192 // fine for most people, but if you're using the Pinscape controller for
mjr 17:ab3cec0c8bf4 193 // your physical button wiring, you should set the launch button to match
mjr 17:ab3cec0c8bf4 194 // where you physically wired your actual Launch Ball button. Likewise,
mjr 17:ab3cec0c8bf4 195 // change the LedWiz port if you're using the one below for some actual
mjr 17:ab3cec0c8bf4 196 // hardware output. This is a virtual port that won't control any hardware;
mjr 17:ab3cec0c8bf4 197 // it's just for signaling the plunger that we're in "button mode". Note
mjr 17:ab3cec0c8bf4 198 // that the numbering for the both the LedWiz port and joystick button
mjr 17:ab3cec0c8bf4 199 // start at 1 to match the DOF Configtool and VP dialog numbering.
mjr 17:ab3cec0c8bf4 200 //
mjr 17:ab3cec0c8bf4 201 // Second, in the DOF Configtool, make sure you have a Pinscape controller
mjr 17:ab3cec0c8bf4 202 // in your cabinet configuration, then go to your Port Assignments and set
mjr 17:ab3cec0c8bf4 203 // the port defined below to "ZB Launch Ball".
mjr 17:ab3cec0c8bf4 204 //
mjr 17:ab3cec0c8bf4 205 // Third, open the Visual Pinball editor, open the Preferences | Keys
mjr 17:ab3cec0c8bf4 206 // dialog, and find the Plunger item. Open the drop-down list under that
mjr 17:ab3cec0c8bf4 207 // item and select the button number defined below.
mjr 17:ab3cec0c8bf4 208 //
mjr 21:5048e16cc9ef 209 // To disable this feature, just set ZBLaunchBallPort to 0 here.
mjr 17:ab3cec0c8bf4 210
mjr 17:ab3cec0c8bf4 211 const int ZBLaunchBallPort = 32;
mjr 17:ab3cec0c8bf4 212 const int LaunchBallButton = 24;
mjr 17:ab3cec0c8bf4 213
mjr 18:5e890ebd0023 214 // Distance necessary to push the plunger to activate the simulated
mjr 18:5e890ebd0023 215 // launch ball button, in inches. A standard pinball plunger can be
mjr 18:5e890ebd0023 216 // pushed forward about 1/2". However, the barrel spring is very
mjr 18:5e890ebd0023 217 // stiff, and anything more than about 1/8" requires quite a bit
mjr 18:5e890ebd0023 218 // of force. Ideally the force required should be about the same as
mjr 18:5e890ebd0023 219 // for any ordinary pushbutton.
mjr 18:5e890ebd0023 220 //
mjr 18:5e890ebd0023 221 // On my cabinet, empirically, a distance around 2mm (.08") seems
mjr 18:5e890ebd0023 222 // to work pretty well. It's far enough that it doesn't trigger
mjr 18:5e890ebd0023 223 // spuriously, but short enough that it responds to a reasonably
mjr 18:5e890ebd0023 224 // light push.
mjr 18:5e890ebd0023 225 //
mjr 18:5e890ebd0023 226 // You might need to adjust this up or down to get the right feel.
mjr 18:5e890ebd0023 227 // Alternatively, if you don't like the "push" gesture at all and
mjr 18:5e890ebd0023 228 // would prefer to only make the plunger respond to a pull-and-release
mjr 18:5e890ebd0023 229 // motion, simply set this to, say, 2.0 - it's impossible to push a
mjr 18:5e890ebd0023 230 // plunger forward that far, so that will effectively turn off the
mjr 18:5e890ebd0023 231 // push mode.
mjr 18:5e890ebd0023 232 const float LaunchBallPushDistance = .08;
mjr 18:5e890ebd0023 233
mjr 17:ab3cec0c8bf4 234
mjr 21:5048e16cc9ef 235 #ifdef DECL_EXTERNS
mjr 17:ab3cec0c8bf4 236 // --------------------------------------------------------------------------
mjr 17:ab3cec0c8bf4 237 //
mjr 17:ab3cec0c8bf4 238
mjr 17:ab3cec0c8bf4 239 // Joystick button input pin assignments.
mjr 17:ab3cec0c8bf4 240 //
mjr 17:ab3cec0c8bf4 241 // You can wire up to 32 GPIO ports to buttons (equipped with
mjr 17:ab3cec0c8bf4 242 // momentary switches). Connect each switch between the desired
mjr 17:ab3cec0c8bf4 243 // GPIO port and ground (J9 pin 12 or 14). When the button is pressed,
mjr 17:ab3cec0c8bf4 244 // we'll tell the host PC that the corresponding joystick button is
mjr 17:ab3cec0c8bf4 245 // pressed. We debounce the keystrokes in software, so you can simply
mjr 17:ab3cec0c8bf4 246 // wire directly to pushbuttons with no additional external hardware.
mjr 17:ab3cec0c8bf4 247 //
mjr 17:ab3cec0c8bf4 248 // Note that we assign 24 buttons by default, even though the USB
mjr 17:ab3cec0c8bf4 249 // joystick interface can handle up to 32 buttons. VP itself only
mjr 17:ab3cec0c8bf4 250 // allows mapping of up to 24 buttons in the preferences dialog
mjr 17:ab3cec0c8bf4 251 // (although it can recognize 32 buttons internally). If you want
mjr 17:ab3cec0c8bf4 252 // more buttons, you can reassign pins that are assigned by default
mjr 17:ab3cec0c8bf4 253 // as LedWiz outputs. To reassign a pin, find the pin you wish to
mjr 17:ab3cec0c8bf4 254 // reassign in the LedWizPortMap array below, and change the pin name
mjr 17:ab3cec0c8bf4 255 // there to NC (for Not Connected). You can then change one of the
mjr 17:ab3cec0c8bf4 256 // "NC" entries below to the reallocated pin name. The limit is 32
mjr 17:ab3cec0c8bf4 257 // buttons total.
mjr 17:ab3cec0c8bf4 258 //
mjr 17:ab3cec0c8bf4 259 // Note: PTD1 (pin J2-12) should NOT be assigned as a button input,
mjr 17:ab3cec0c8bf4 260 // as this pin is physically connected on the KL25Z to the on-board
mjr 17:ab3cec0c8bf4 261 // indicator LED's blue segment. This precludes any other use of
mjr 17:ab3cec0c8bf4 262 // the pin.
mjr 17:ab3cec0c8bf4 263 PinName buttonMap[] = {
mjr 17:ab3cec0c8bf4 264 PTC2, // J10 pin 10, joystick button 1
mjr 17:ab3cec0c8bf4 265 PTB3, // J10 pin 8, joystick button 2
mjr 17:ab3cec0c8bf4 266 PTB2, // J10 pin 6, joystick button 3
mjr 17:ab3cec0c8bf4 267 PTB1, // J10 pin 4, joystick button 4
mjr 17:ab3cec0c8bf4 268
mjr 17:ab3cec0c8bf4 269 PTE30, // J10 pin 11, joystick button 5
mjr 17:ab3cec0c8bf4 270 PTE22, // J10 pin 5, joystick button 6
mjr 17:ab3cec0c8bf4 271
mjr 17:ab3cec0c8bf4 272 PTE5, // J9 pin 15, joystick button 7
mjr 17:ab3cec0c8bf4 273 PTE4, // J9 pin 13, joystick button 8
mjr 17:ab3cec0c8bf4 274 PTE3, // J9 pin 11, joystick button 9
mjr 17:ab3cec0c8bf4 275 PTE2, // J9 pin 9, joystick button 10
mjr 17:ab3cec0c8bf4 276 PTB11, // J9 pin 7, joystick button 11
mjr 17:ab3cec0c8bf4 277 PTB10, // J9 pin 5, joystick button 12
mjr 17:ab3cec0c8bf4 278 PTB9, // J9 pin 3, joystick button 13
mjr 17:ab3cec0c8bf4 279 PTB8, // J9 pin 1, joystick button 14
mjr 17:ab3cec0c8bf4 280
mjr 17:ab3cec0c8bf4 281 PTC12, // J2 pin 1, joystick button 15
mjr 17:ab3cec0c8bf4 282 PTC13, // J2 pin 3, joystick button 16
mjr 17:ab3cec0c8bf4 283 PTC16, // J2 pin 5, joystick button 17
mjr 17:ab3cec0c8bf4 284 PTC17, // J2 pin 7, joystick button 18
mjr 17:ab3cec0c8bf4 285 PTA16, // J2 pin 9, joystick button 19
mjr 17:ab3cec0c8bf4 286 PTA17, // J2 pin 11, joystick button 20
mjr 17:ab3cec0c8bf4 287 PTE31, // J2 pin 13, joystick button 21
mjr 17:ab3cec0c8bf4 288 PTD6, // J2 pin 17, joystick button 22
mjr 17:ab3cec0c8bf4 289 PTD7, // J2 pin 19, joystick button 23
mjr 17:ab3cec0c8bf4 290
mjr 17:ab3cec0c8bf4 291 PTE1, // J2 pin 20, joystick button 24
mjr 17:ab3cec0c8bf4 292
mjr 17:ab3cec0c8bf4 293 NC, // not used, joystick button 25
mjr 17:ab3cec0c8bf4 294 NC, // not used, joystick button 26
mjr 17:ab3cec0c8bf4 295 NC, // not used, joystick button 27
mjr 17:ab3cec0c8bf4 296 NC, // not used, joystick button 28
mjr 17:ab3cec0c8bf4 297 NC, // not used, joystick button 29
mjr 17:ab3cec0c8bf4 298 NC, // not used, joystick button 30
mjr 17:ab3cec0c8bf4 299 NC, // not used, joystick button 31
mjr 17:ab3cec0c8bf4 300 NC // not used, joystick button 32
mjr 17:ab3cec0c8bf4 301 };
mjr 17:ab3cec0c8bf4 302
mjr 17:ab3cec0c8bf4 303 // --------------------------------------------------------------------------
mjr 17:ab3cec0c8bf4 304 //
mjr 17:ab3cec0c8bf4 305 // LED-Wiz emulation output pin assignments.
mjr 17:ab3cec0c8bf4 306 //
mjr 17:ab3cec0c8bf4 307 // The LED-Wiz protocol allows setting individual intensity levels
mjr 17:ab3cec0c8bf4 308 // on all outputs, with 48 levels of intensity. This can be used
mjr 17:ab3cec0c8bf4 309 // to control lamp brightness and motor speeds, among other things.
mjr 17:ab3cec0c8bf4 310 // Unfortunately, the KL25Z only has 10 PWM channels, so while we
mjr 17:ab3cec0c8bf4 311 // can support the full complement of 32 outputs, we can only provide
mjr 17:ab3cec0c8bf4 312 // PWM dimming/speed control on 10 of them. The remaining outputs
mjr 17:ab3cec0c8bf4 313 // can only be switched fully on and fully off - we can't support
mjr 17:ab3cec0c8bf4 314 // dimming on these, so they'll ignore any intensity level setting
mjr 17:ab3cec0c8bf4 315 // requested by the host. Use these for devices that don't have any
mjr 17:ab3cec0c8bf4 316 // use for intensity settings anyway, such as contactors and knockers.
mjr 17:ab3cec0c8bf4 317 //
mjr 17:ab3cec0c8bf4 318 // Ports with pins assigned as "NC" are not connected. That is,
mjr 17:ab3cec0c8bf4 319 // there's no physical pin for that LedWiz port number. You can
mjr 17:ab3cec0c8bf4 320 // send LedWiz commands to turn NC ports on and off, but doing so
mjr 17:ab3cec0c8bf4 321 // will have no effect. The reason we leave some ports unassigned
mjr 17:ab3cec0c8bf4 322 // is that we don't have enough physical GPIO pins to fill out the
mjr 17:ab3cec0c8bf4 323 // full LedWiz complement of 32 ports. Many pins are already taken
mjr 17:ab3cec0c8bf4 324 // for other purposes, such as button inputs or the plunger CCD
mjr 17:ab3cec0c8bf4 325 // interface.
mjr 17:ab3cec0c8bf4 326 //
mjr 17:ab3cec0c8bf4 327 // The mapping between physical output pins on the KL25Z and the
mjr 17:ab3cec0c8bf4 328 // assigned LED-Wiz port numbers is essentially arbitrary - you can
mjr 17:ab3cec0c8bf4 329 // customize this by changing the entries in the array below if you
mjr 17:ab3cec0c8bf4 330 // wish to rearrange the pins for any reason. Be aware that some
mjr 17:ab3cec0c8bf4 331 // of the physical outputs are already used for other purposes
mjr 17:ab3cec0c8bf4 332 // (e.g., some of the GPIO pins on header J10 are used for the
mjr 17:ab3cec0c8bf4 333 // CCD sensor - but you can of course reassign those as well by
mjr 17:ab3cec0c8bf4 334 // changing the corresponding declarations elsewhere in this module).
mjr 17:ab3cec0c8bf4 335 // The assignments we make here have two main objectives: first,
mjr 17:ab3cec0c8bf4 336 // to group the outputs on headers J1 and J2 (to facilitate neater
mjr 17:ab3cec0c8bf4 337 // wiring by keeping the output pins together physically), and
mjr 17:ab3cec0c8bf4 338 // second, to make the physical pin layout match the LED-Wiz port
mjr 17:ab3cec0c8bf4 339 // numbering order to the extent possible. There's one big wrench
mjr 17:ab3cec0c8bf4 340 // in the works, though, which is the limited number and discontiguous
mjr 17:ab3cec0c8bf4 341 // placement of the KL25Z PWM-capable output pins. This prevents
mjr 17:ab3cec0c8bf4 342 // us from doing the most obvious sequential ordering of the pins,
mjr 17:ab3cec0c8bf4 343 // so we end up with the outputs arranged into several blocks.
mjr 17:ab3cec0c8bf4 344 // Hopefully this isn't too confusing; for more detailed rationale,
mjr 17:ab3cec0c8bf4 345 // read on...
mjr 17:ab3cec0c8bf4 346 //
mjr 17:ab3cec0c8bf4 347 // With the LED-Wiz, the host software configuration usually
mjr 17:ab3cec0c8bf4 348 // assumes that each RGB LED is hooked up to three consecutive ports
mjr 17:ab3cec0c8bf4 349 // (for the red, green, and blue components, which need to be
mjr 17:ab3cec0c8bf4 350 // physically wired to separate outputs to allow each color to be
mjr 17:ab3cec0c8bf4 351 // controlled independently). To facilitate this, we arrange the
mjr 17:ab3cec0c8bf4 352 // PWM-enabled outputs so that they're grouped together in the
mjr 17:ab3cec0c8bf4 353 // port numbering scheme. Unfortunately, these outputs aren't
mjr 17:ab3cec0c8bf4 354 // together in a single group in the physical pin layout, so to
mjr 17:ab3cec0c8bf4 355 // group them logically in the LED-Wiz port numbering scheme, we
mjr 17:ab3cec0c8bf4 356 // have to break up the overall numbering scheme into several blocks.
mjr 17:ab3cec0c8bf4 357 // So our port numbering goes sequentially down each column of
mjr 17:ab3cec0c8bf4 358 // header pins, but there are several break points where we have
mjr 17:ab3cec0c8bf4 359 // to interrupt the obvious sequence to keep the PWM pins grouped
mjr 17:ab3cec0c8bf4 360 // logically.
mjr 17:ab3cec0c8bf4 361 //
mjr 17:ab3cec0c8bf4 362 // In the list below, "pin J1-2" refers to pin 2 on header J1 on
mjr 17:ab3cec0c8bf4 363 // the KL25Z, using the standard pin numbering in the KL25Z
mjr 17:ab3cec0c8bf4 364 // documentation - this is the physical pin that the port controls.
mjr 17:ab3cec0c8bf4 365 // "LW port 1" means LED-Wiz port 1 - this is the LED-Wiz port
mjr 17:ab3cec0c8bf4 366 // number that you use on the PC side (in the DirectOutput config
mjr 17:ab3cec0c8bf4 367 // file, for example) to address the port. PWM-capable ports are
mjr 17:ab3cec0c8bf4 368 // marked as such - we group the PWM-capable ports into the first
mjr 17:ab3cec0c8bf4 369 // 10 LED-Wiz port numbers.
mjr 17:ab3cec0c8bf4 370 //
mjr 17:ab3cec0c8bf4 371 // If you wish to reallocate a pin in the array below to some other
mjr 17:ab3cec0c8bf4 372 // use, such as a button input port, simply change the pin name in
mjr 17:ab3cec0c8bf4 373 // the entry to NC (for Not Connected). This will disable the given
mjr 17:ab3cec0c8bf4 374 // logical LedWiz port number and free up the physical pin.
mjr 17:ab3cec0c8bf4 375 //
mjr 17:ab3cec0c8bf4 376 // If you wish to reallocate a pin currently assigned to the button
mjr 17:ab3cec0c8bf4 377 // input array, simply change the entry for the pin in the buttonMap[]
mjr 17:ab3cec0c8bf4 378 // array above to NC (for "not connected"), and plug the pin name into
mjr 17:ab3cec0c8bf4 379 // a slot of your choice in the array below.
mjr 17:ab3cec0c8bf4 380 //
mjr 17:ab3cec0c8bf4 381 // Note: PTD1 (pin J2-12) should NOT be assigned as an LedWiz output,
mjr 17:ab3cec0c8bf4 382 // as this pin is physically connected on the KL25Z to the on-board
mjr 17:ab3cec0c8bf4 383 // indicator LED's blue segment. This precludes any other use of
mjr 17:ab3cec0c8bf4 384 // the pin.
mjr 17:ab3cec0c8bf4 385 //
mjr 17:ab3cec0c8bf4 386 struct {
mjr 17:ab3cec0c8bf4 387 PinName pin;
mjr 17:ab3cec0c8bf4 388 bool isPWM;
mjr 17:ab3cec0c8bf4 389 } ledWizPortMap[32] = {
mjr 17:ab3cec0c8bf4 390 { PTA1, true }, // pin J1-2, LW port 1 (PWM capable - TPM 2.0 = channel 9)
mjr 17:ab3cec0c8bf4 391 { PTA2, true }, // pin J1-4, LW port 2 (PWM capable - TPM 2.1 = channel 10)
mjr 17:ab3cec0c8bf4 392 { PTD4, true }, // pin J1-6, LW port 3 (PWM capable - TPM 0.4 = channel 5)
mjr 17:ab3cec0c8bf4 393 { PTA12, true }, // pin J1-8, LW port 4 (PWM capable - TPM 1.0 = channel 7)
mjr 17:ab3cec0c8bf4 394 { PTA4, true }, // pin J1-10, LW port 5 (PWM capable - TPM 0.1 = channel 2)
mjr 17:ab3cec0c8bf4 395 { PTA5, true }, // pin J1-12, LW port 6 (PWM capable - TPM 0.2 = channel 3)
mjr 17:ab3cec0c8bf4 396 { PTA13, true }, // pin J2-2, LW port 7 (PWM capable - TPM 1.1 = channel 13)
mjr 17:ab3cec0c8bf4 397 { PTD5, true }, // pin J2-4, LW port 8 (PWM capable - TPM 0.5 = channel 6)
mjr 17:ab3cec0c8bf4 398 { PTD0, true }, // pin J2-6, LW port 9 (PWM capable - TPM 0.0 = channel 1)
mjr 17:ab3cec0c8bf4 399 { PTD3, true }, // pin J2-10, LW port 10 (PWM capable - TPM 0.3 = channel 4)
mjr 17:ab3cec0c8bf4 400 { PTD2, false }, // pin J2-8, LW port 11
mjr 17:ab3cec0c8bf4 401 { PTC8, false }, // pin J1-14, LW port 12
mjr 17:ab3cec0c8bf4 402 { PTC9, false }, // pin J1-16, LW port 13
mjr 17:ab3cec0c8bf4 403 { PTC7, false }, // pin J1-1, LW port 14
mjr 17:ab3cec0c8bf4 404 { PTC0, false }, // pin J1-3, LW port 15
mjr 17:ab3cec0c8bf4 405 { PTC3, false }, // pin J1-5, LW port 16
mjr 17:ab3cec0c8bf4 406 { PTC4, false }, // pin J1-7, LW port 17
mjr 17:ab3cec0c8bf4 407 { PTC5, false }, // pin J1-9, LW port 18
mjr 17:ab3cec0c8bf4 408 { PTC6, false }, // pin J1-11, LW port 19
mjr 17:ab3cec0c8bf4 409 { PTC10, false }, // pin J1-13, LW port 20
mjr 17:ab3cec0c8bf4 410 { PTC11, false }, // pin J1-15, LW port 21
mjr 17:ab3cec0c8bf4 411 { PTE0, false }, // pin J2-18, LW port 22
mjr 17:ab3cec0c8bf4 412 { NC, false }, // Not used, LW port 23
mjr 17:ab3cec0c8bf4 413 { NC, false }, // Not used, LW port 24
mjr 17:ab3cec0c8bf4 414 { NC, false }, // Not used, LW port 25
mjr 17:ab3cec0c8bf4 415 { NC, false }, // Not used, LW port 26
mjr 17:ab3cec0c8bf4 416 { NC, false }, // Not used, LW port 27
mjr 17:ab3cec0c8bf4 417 { NC, false }, // Not used, LW port 28
mjr 17:ab3cec0c8bf4 418 { NC, false }, // Not used, LW port 29
mjr 17:ab3cec0c8bf4 419 { NC, false }, // Not used, LW port 30
mjr 17:ab3cec0c8bf4 420 { NC, false }, // Not used, LW port 31
mjr 17:ab3cec0c8bf4 421 { NC, false } // Not used, LW port 32
mjr 17:ab3cec0c8bf4 422 };
mjr 17:ab3cec0c8bf4 423
mjr 21:5048e16cc9ef 424
mjr 21:5048e16cc9ef 425 #endif // DECL_EXTERNS