An I/O controller for virtual pinball machines: accelerometer nudge sensing, analog plunger input, button input encoding, LedWiz compatible output controls, and more.

Dependencies:   mbed FastIO FastPWM USBDevice

Fork of Pinscape_Controller by Mike R

/media/uploads/mjr/pinscape_no_background_small_L7Miwr6.jpg

This is Version 2 of the Pinscape Controller, an I/O controller for virtual pinball machines. (You can find the old version 1 software here.) Pinscape is software for the KL25Z that turns the board into a full-featured I/O controller for virtual pinball, with support for accelerometer-based nudging, a real plunger, button inputs, and feedback device control.

In case you haven't heard of the concept before, a "virtual pinball machine" is basically a video pinball simulator that's built into a real pinball machine body. A TV monitor goes in place of the pinball playfield, and a second TV goes in the backbox to serve as the "backglass" display. A third smaller monitor can serve as the "DMD" (the Dot Matrix Display used for scoring on newer machines), or you can even install a real pinball plasma DMD. A computer is hidden inside the cabinet, running pinball emulation software that displays a life-sized playfield on the main TV. The cabinet has all of the usual buttons, too, so it not only looks like the real thing, but plays like it too. That's a picture of my own machine to the right. On the outside, it's built exactly like a real arcade pinball machine, with the same overall dimensions and all of the standard pinball cabinet hardware.

A few small companies build and sell complete, finished virtual pinball machines, but I think it's more fun as a DIY project. If you have some basic wood-working skills and know your way around PCs, you can build one from scratch. The computer part is just an ordinary Windows PC, and all of the pinball emulation can be built out of free, open-source software. In that spirit, the Pinscape Controller is an open-source software/hardware project that offers a no-compromises, all-in-one control center for all of the unique input/output needs of a virtual pinball cabinet. If you've been thinking about building one of these, but you're not sure how to connect a plunger, flipper buttons, lights, nudge sensor, and whatever else you can think of, this project might be just what you're looking for.

You can find much more information about DIY Pin Cab building in general in the Virtual Cabinet Forum on vpforums.org. Also visit my Pinscape Resources page for more about this project and other virtual pinball projects I'm working on.

Downloads

  • Pinscape Release Builds: This page has download links for all of the Pinscape software. To get started, install and run the Pinscape Config Tool on your Windows computer. It will lead you through the steps for installing the Pinscape firmware on the KL25Z.
  • Config Tool Source Code. The complete C# source code for the config tool. You don't need this to run the tool, but it's available if you want to customize anything or see how it works inside.

Documentation

The new Version 2 Build Guide is now complete! This new version aims to be a complete guide to building a virtual pinball machine, including not only the Pinscape elements but all of the basics, from sourcing parts to building all of the hardware.

You can also refer to the original Hardware Build Guide (PDF), but that's out of date now, since it refers to the old version 1 software, which was rather different (especially when it comes to configuration).

System Requirements

The new config tool requires a fairly up-to-date Microsoft .NET installation. If you use Windows Update to keep your system current, you should be fine. A modern version of Internet Explorer (IE) is required, even if you don't use it as your main browser, because the config tool uses some system components that Microsoft packages into the IE install set. I test with IE11, so that's known to work. IE8 doesn't work. IE9 and 10 are unknown at this point.

The Windows requirements are only for the config tool. The firmware doesn't care about anything on the Windows side, so if you can make do without the config tool, you can use almost any Windows setup.

Main Features

Plunger: The Pinscape Controller started out as a "mechanical plunger" controller: a device for attaching a real pinball plunger to the video game software so that you could launch the ball the natural way. This is still, of course, a central feature of the project. The software supports several types of sensors: a high-resolution optical sensor (which works by essentially taking pictures of the plunger as it moves); a slide potentionmeter (which determines the position via the changing electrical resistance in the pot); a quadrature sensor (which counts bars printed on a special guide rail that it moves along); and an IR distance sensor (which determines the position by sending pulses of light at the plunger and measuring the round-trip travel time). The Build Guide explains how to set up each type of sensor.

Nudging: The KL25Z (the little microcontroller that the software runs on) has a built-in accelerometer. The Pinscape software uses it to sense when you nudge the cabinet, and feeds the acceleration data to the pinball software on the PC. This turns physical nudges into virtual English on the ball. The accelerometer is quite sensitive and accurate, so we can measure the difference between little bumps and hard shoves, and everything in between. The result is natural and immersive.

Buttons: You can wire real pinball buttons to the KL25Z, and the software will translate the buttons into PC input. You have the option to map each button to a keyboard key or joystick button. You can wire up your flipper buttons, Magna Save buttons, Start button, coin slots, operator buttons, and whatever else you need.

Feedback devices: You can also attach "feedback devices" to the KL25Z. Feedback devices are things that create tactile, sound, and lighting effects in sync with the game action. The most popular PC pinball emulators know how to address a wide variety of these devices, and know how to match them to on-screen action in each virtual table. You just need an I/O controller that translates commands from the PC into electrical signals that turn the devices on and off. The Pinscape Controller can do that for you.

Expansion Boards

There are two main ways to run the Pinscape Controller: standalone, or using the "expansion boards".

In the basic standalone setup, you just need the KL25Z, plus whatever buttons, sensors, and feedback devices you want to attach to it. This mode lets you take advantage of everything the software can do, but for some features, you'll have to build some ad hoc external circuitry to interface external devices with the KL25Z. The Build Guide has detailed plans for exactly what you need to build.

The other option is the Pinscape Expansion Boards. The expansion boards are a companion project, which is also totally free and open-source, that provides Printed Circuit Board (PCB) layouts that are designed specifically to work with the Pinscape software. The PCB designs are in the widely used EAGLE format, which many PCB manufacturers can turn directly into physical boards for you. The expansion boards organize all of the external connections more neatly than on the standalone KL25Z, and they add all of the interface circuitry needed for all of the advanced software functions. The big thing they bring to the table is lots of high-power outputs. The boards provide a modular system that lets you add boards to add more outputs. If you opt for the basic core setup, you'll have enough outputs for all of the toys in a really well-equipped cabinet. If your ambitions go beyond merely well-equipped and run to the ridiculously extravagant, just add an extra board or two. The modular design also means that you can add to the system over time.

Expansion Board project page

Update notes

If you have a Pinscape V1 setup already installed, you should be able to switch to the new version pretty seamlessly. There are just a couple of things to be aware of.

First, the "configuration" procedure is completely different in the new version. Way better and way easier, but it's not what you're used to from V1. In V1, you had to edit the project source code and compile your own custom version of the program. No more! With V2, you simply install the standard, pre-compiled .bin file, and select options using the Pinscape Config Tool on Windows.

Second, if you're using the TSL1410R optical sensor for your plunger, there's a chance you'll need to boost your light source's brightness a little bit. The "shutter speed" is faster in this version, which means that it doesn't spend as much time collecting light per frame as before. The software actually does "auto exposure" adaptation on every frame, so the increased shutter speed really shouldn't bother it, but it does require a certain minimum level of contrast, which requires a certain minimal level of lighting. Check the plunger viewer in the setup tool if you have any problems; if the image looks totally dark, try increasing the light level to see if that helps.

New Features

V2 has numerous new features. Here are some of the highlights...

Dynamic configuration: as explained above, configuration is now handled through the Config Tool on Windows. It's no longer necessary to edit the source code or compile your own modified binary.

Improved plunger sensing: the software now reads the TSL1410R optical sensor about 15x faster than it did before. This allows reading the sensor at full resolution (400dpi), about 400 times per second. The faster frame rate makes a big difference in how accurately we can read the plunger position during the fast motion of a release, which allows for more precise position sensing and faster response. The differences aren't dramatic, since the sensing was already pretty good even with the slower V1 scan rate, but you might notice a little better precision in tricky skill shots.

Keyboard keys: button inputs can now be mapped to keyboard keys. The joystick button option is still available as well, of course. Keyboard keys have the advantage of being closer to universal for PC pinball software: some pinball software can be set up to take joystick input, but nearly all PC pinball emulators can take keyboard input, and nearly all of them use the same key mappings.

Local shift button: one physical button can be designed as the local shift button. This works like a Shift button on a keyboard, but with cabinet buttons. It allows each physical button on the cabinet to have two PC keys assigned, one normal and one shifted. Hold down the local shift button, then press another key, and the other key's shifted key mapping is sent to the PC. The shift button can have a regular key mapping of its own as well, so it can do double duty. The shift feature lets you access more functions without cluttering your cabinet with extra buttons. It's especially nice for less frequently used functions like adjusting the volume or activating night mode.

Night mode: the output controller has a new "night mode" option, which lets you turn off all of your noisy devices with a single button, switch, or PC command. You can designate individual ports as noisy or not. Night mode only disables the noisemakers, so you still get the benefit of your flashers, button lights, and other quiet devices. This lets you play late into the night without disturbing your housemates or neighbors.

Gamma correction: you can designate individual output ports for gamma correction. This adjusts the intensity level of an output to make it match the way the human eye perceives brightness, so that fades and color mixes look more natural in lighting devices. You can apply this to individual ports, so that it only affects ports that actually have lights of some kind attached.

IR Remote Control: the controller software can transmit and/or receive IR remote control commands if you attach appropriate parts (an IR LED to send, an IR sensor chip to receive). This can be used to turn on your TV(s) when the system powers on, if they don't turn on automatically, and for any other functions you can think of requiring IR send/receive capabilities. You can assign IR commands to cabinet buttons, so that pressing a button on your cabinet sends a remote control command from the attached IR LED, and you can have the controller generate virtual key presses on your PC in response to received IR commands. If you have the IR sensor attached, the system can use it to learn commands from your existing remotes.

Yet more USB fixes: I've been gradually finding and fixing USB bugs in the mbed library for months now. This version has all of the fixes of the last couple of releases, of course, plus some new ones. It also has a new "last resort" feature, since there always seems to be "just one more" USB bug. The last resort is that you can tell the device to automatically reboot itself if it loses the USB connection and can't restore it within a given time limit.

More Downloads

  • Custom VP builds: I created modified versions of Visual Pinball 9.9 and Physmod5 that you might want to use in combination with this controller. The modified versions have special handling for plunger calibration specific to the Pinscape Controller, as well as some enhancements to the nudge physics. If you're not using the plunger, you might still want it for the nudge improvements. The modified version also works with any other input controller, so you can get the enhanced nudging effects even if you're using a different plunger/nudge kit. The big change in the modified versions is a "filter" for accelerometer input that's designed to make the response to cabinet nudges more realistic. It also makes the response more subdued than in the standard VP, so it's not to everyone's taste. The downloads include both the updated executables and the source code changes, in case you want to merge the changes into your own custom version(s).

    Note! These features are now standard in the official VP releases, so you don't need my custom builds if you're using 9.9.1 or later and/or VP 10. I don't think there's any reason to use my versions instead of the latest official ones, and in fact I'd encourage you to use the official releases since they're more up to date, but I'm leaving my builds available just in case. In the official versions, look for the checkbox "Enable Nudge Filter" in the Keys preferences dialog. My custom versions don't include that checkbox; they just enable the filter unconditionally.
  • Output circuit shopping list: This is a saved shopping cart at mouser.com with the parts needed to build one copy of the high-power output circuit for the LedWiz emulator feature, for use with the standalone KL25Z (that is, without the expansion boards). The quantities in the cart are for one output channel, so if you want N outputs, simply multiply the quantities by the N, with one exception: you only need one ULN2803 transistor array chip for each eight output circuits. If you're using the expansion boards, you won't need any of this, since the boards provide their own high-power outputs.
  • Cary Owens' optical sensor housing: A 3D-printable design for a housing/mounting bracket for the optical plunger sensor, designed by Cary Owens. This makes it easy to mount the sensor.
  • Lemming77's potentiometer mounting bracket and shooter rod connecter: Sketchup designs for 3D-printable parts for mounting a slide potentiometer as the plunger sensor. These were designed for a particular slide potentiometer that used to be available from an Aliexpress.com seller but is no longer listed. You can probably use this design as a starting point for other similar devices; just check the dimensions before committing the design to plastic.

Copyright and License

The Pinscape firmware is copyright 2014, 2021 by Michael J Roberts. It's released under an MIT open-source license. See License.

Warning to VirtuaPin Kit Owners

This software isn't designed as a replacement for the VirtuaPin plunger kit's firmware. If you bought the VirtuaPin kit, I recommend that you don't install this software. The VirtuaPin kit uses the same KL25Z microcontroller that Pinscape uses, but the rest of its hardware is different and incompatible. In particular, the Pinscape firmware doesn't include support for the IR proximity sensor used in the VirtuaPin plunger kit, so you won't be able to use your plunger device with the Pinscape firmware. In addition, the VirtuaPin setup uses a different set of GPIO pins for the button inputs from the Pinscape defaults, so if you do install the Pinscape firmware, you'll have to go into the Config Tool and reassign all of the buttons to match the VirtuaPin wiring.

Committer:
mjr
Date:
Fri Mar 17 22:02:08 2017 +0000
Revision:
77:0b96f6867312
Parent:
69:cc5039284fac
Child:
78:1e00b3fa11af
New memory pool management; keeping old ones as #ifdefs for now for reference.

Who changed what in which revision?

UserRevisionLine numberNew contents of line
mjr 17:ab3cec0c8bf4 1 // Pinscape Controller Configuration
mjr 17:ab3cec0c8bf4 2 //
mjr 55:4db125cd11a0 3 // New for 2016: dynamic configuration! To configure the controller,
mjr 55:4db125cd11a0 4 // connect the KL25Z to your PC, install the STANDARD pre-compiled .bin
mjr 55:4db125cd11a0 5 // file, and run the Windows config tool. There's no need (as there was in
mjr 55:4db125cd11a0 6 // the past) to edit the source code or to compile a custom version of the
mjr 55:4db125cd11a0 7 // binary just to customize setup options.
mjr 35:e959ffba78fd 8 //
mjr 55:4db125cd11a0 9 // In earlier versions, configuration was handled mostly with #ifdef and
mjr 55:4db125cd11a0 10 // similar constructs. To customize the setup, you had to create a private
mjr 55:4db125cd11a0 11 // forked copy of the source code, edit the constants defined in config.h,
mjr 55:4db125cd11a0 12 // and compile a custom binary. That's no longer necessary!
mjr 35:e959ffba78fd 13 //
mjr 35:e959ffba78fd 14 // The new approach is to do everything (or as much as possible, anyway)
mjr 35:e959ffba78fd 15 // via the Windows config tool. You shouldn't have to recompile a custom
mjr 35:e959ffba78fd 16 // version just to make a configurable change. Of course, you're still free
mjr 55:4db125cd11a0 17 // to create a custom version if you want to add entirely new features or
mjr 55:4db125cd11a0 18 // make changes that go beyond what the setup tool exposes.
mjr 35:e959ffba78fd 19 //
mjr 35:e959ffba78fd 20
mjr 55:4db125cd11a0 21 // Pre-packaged configuration selection.
mjr 55:4db125cd11a0 22 //
mjr 55:4db125cd11a0 23 // IMPORTANT! If you just want to create a custom configuration, DON'T
mjr 55:4db125cd11a0 24 // modify this file, DON'T use these macros, and DON'T compiler on mbed.
mjr 55:4db125cd11a0 25 // Instead, use the unmodified standard build and configure your system
mjr 55:4db125cd11a0 26 // using the Pinscape Config Tool on Windows. That's easier and better
mjr 55:4db125cd11a0 27 // because the config tool will be able to back up your settings to a
mjr 55:4db125cd11a0 28 // local file on your PC, and will automatically preserve your settings
mjr 55:4db125cd11a0 29 // across upgrades. You won't have to worry about merging your changes
mjr 55:4db125cd11a0 30 // into every update of the repository source code, since you'll never
mjr 55:4db125cd11a0 31 // have to change the source code.
mjr 55:4db125cd11a0 32 //
mjr 55:4db125cd11a0 33 // The different configurations here are purely for testing purposes.
mjr 55:4db125cd11a0 34 // The standard build uses the STANDARD_CONFIG settings, which are the
mjr 55:4db125cd11a0 35 // same as the original version where you had to modify config.h by hand
mjr 55:4db125cd11a0 36 // to customize your system.
mjr 55:4db125cd11a0 37 //
mjr 55:4db125cd11a0 38 #define STANDARD_CONFIG 1 // standard settings, based on v1 base settings
mjr 55:4db125cd11a0 39 #define TEST_CONFIG_EXPAN 0 // configuration for the expansion boards
mjr 77:0b96f6867312 40 #define TEST_KEEP_PRINTF 1 // for debugging purposes, keep printf() enabled
mjr 55:4db125cd11a0 41 // by leaving the SDA UART GPIO pins unallocated
mjr 48:058ace2aed1d 42
mjr 17:ab3cec0c8bf4 43
mjr 25:e22b88bd783a 44 #ifndef CONFIG_H
mjr 25:e22b88bd783a 45 #define CONFIG_H
mjr 17:ab3cec0c8bf4 46
mjr 35:e959ffba78fd 47 // Plunger type codes
mjr 35:e959ffba78fd 48 // NOTE! These values are part of the external USB interface. New
mjr 35:e959ffba78fd 49 // values can be added, but the meaning of an existing assigned number
mjr 35:e959ffba78fd 50 // should remain fixed to keep the PC-side config tool compatible across
mjr 35:e959ffba78fd 51 // versions.
mjr 35:e959ffba78fd 52 const int PlungerType_None = 0; // no plunger
mjr 35:e959ffba78fd 53 const int PlungerType_TSL1410RS = 1; // TSL1410R linear image sensor (1280x1 pixels, 400dpi), serial mode
mjr 35:e959ffba78fd 54 const int PlungerType_TSL1410RP = 2; // TSL1410R, parallel mode (reads the two sensor sections concurrently)
mjr 69:cc5039284fac 55 const int PlungerType_TSL1412SS = 3; // TSL1412S linear image sensor (1536x1 pixels, 400dpi), serial mode
mjr 69:cc5039284fac 56 const int PlungerType_TSL1412SP = 4; // TSL1412S, parallel mode
mjr 35:e959ffba78fd 57 const int PlungerType_Pot = 5; // potentionmeter
mjr 35:e959ffba78fd 58 const int PlungerType_OptQuad = 6; // AEDR8300 optical quadrature sensor
mjr 35:e959ffba78fd 59 const int PlungerType_MagQuad = 7; // AS5304 magnetic quadrature sensor
mjr 21:5048e16cc9ef 60
mjr 35:e959ffba78fd 61 // Accelerometer orientation codes
mjr 35:e959ffba78fd 62 // These values are part of the external USB interface
mjr 35:e959ffba78fd 63 const int OrientationFront = 0; // USB ports pointed toward front of cabinet
mjr 35:e959ffba78fd 64 const int OrientationLeft = 1; // ports pointed toward left side of cabinet
mjr 35:e959ffba78fd 65 const int OrientationRight = 2; // ports pointed toward right side of cabinet
mjr 35:e959ffba78fd 66 const int OrientationRear = 3; // ports pointed toward back of cabinet
mjr 25:e22b88bd783a 67
mjr 77:0b96f6867312 68 // Accelerometer dynamic range codes
mjr 77:0b96f6867312 69 const int AccelRange1G = 0; // +/-1G
mjr 77:0b96f6867312 70 const int AccelRange2G = 1; // +/-2G
mjr 77:0b96f6867312 71 const int AccelRange4G = 2; // +/-4G
mjr 77:0b96f6867312 72 const int AccelRange8G = 3; // +/-8G
mjr 77:0b96f6867312 73
mjr 35:e959ffba78fd 74 // input button types
mjr 53:9b2611964afc 75 const int BtnTypeNone = 0; // unused
mjr 35:e959ffba78fd 76 const int BtnTypeJoystick = 1; // joystick button
mjr 53:9b2611964afc 77 const int BtnTypeKey = 2; // keyboard key
mjr 67:c39e66c4e000 78 const int BtnTypeMedia = 3; // media control key
mjr 38:091e511ce8a0 79
mjr 38:091e511ce8a0 80 // input button flags
mjr 38:091e511ce8a0 81 const uint8_t BtnFlagPulse = 0x01; // pulse mode - reports each change in the physical switch state
mjr 38:091e511ce8a0 82 // as a brief press of the logical button/keyboard key
mjr 40:cc0d9814522b 83
mjr 40:cc0d9814522b 84 // button setup structure
mjr 40:cc0d9814522b 85 struct ButtonCfg
mjr 40:cc0d9814522b 86 {
mjr 66:2e3583fbd2f4 87 // physical GPIO pin - a Wire-to-PinName mapping index
mjr 66:2e3583fbd2f4 88 uint8_t pin;
mjr 66:2e3583fbd2f4 89
mjr 66:2e3583fbd2f4 90 // Key type and value reported to the PC
mjr 40:cc0d9814522b 91 uint8_t typ; // key type reported to PC - a BtnTypeXxx value
mjr 53:9b2611964afc 92 uint8_t val; // key value reported - meaning depends on 'typ' value:
mjr 53:9b2611964afc 93 // none -> no PC input reports (val is unused)
mjr 53:9b2611964afc 94 // joystick -> val is joystick button number (1..32)
mjr 53:9b2611964afc 95 // keyboard -> val is USB scan code
mjr 77:0b96f6867312 96 uint8_t IRCommand; // IR command to send when the button is pressed, as
mjr 77:0b96f6867312 97 // an IR command slot number: 1..MAX_IR_CODES, or 0
mjr 77:0b96f6867312 98 // if no IR command is to be sent
mjr 66:2e3583fbd2f4 99
mjr 66:2e3583fbd2f4 100 // Shifted key type and value. These used when the button is pressed
mjr 66:2e3583fbd2f4 101 // while the Local Shift Button is being held down. We send the key
mjr 66:2e3583fbd2f4 102 // code given here instead of the regular typ/val code in this case.
mjr 66:2e3583fbd2f4 103 // If typ2 is BtnTypeNone, we use the regular typ/val code whether or
mjr 66:2e3583fbd2f4 104 // not the shift button is being held.
mjr 66:2e3583fbd2f4 105 uint8_t typ2; // shifted key type
mjr 66:2e3583fbd2f4 106 uint8_t val2; // shifted key value
mjr 77:0b96f6867312 107 uint8_t IRCommand2; // IR command to send when shifted button is pressed
mjr 66:2e3583fbd2f4 108
mjr 66:2e3583fbd2f4 109 // key flags - a bitwise combination of BtnFlagXxx values
mjr 66:2e3583fbd2f4 110 uint8_t flags;
mjr 40:cc0d9814522b 111
mjr 40:cc0d9814522b 112 void set(uint8_t pin, uint8_t typ, uint8_t val, uint8_t flags = 0)
mjr 40:cc0d9814522b 113 {
mjr 40:cc0d9814522b 114 this->pin = pin;
mjr 40:cc0d9814522b 115 this->typ = typ;
mjr 40:cc0d9814522b 116 this->val = val;
mjr 77:0b96f6867312 117 this->IRCommand = 0;
mjr 40:cc0d9814522b 118 this->flags = flags;
mjr 77:0b96f6867312 119 this->typ2 = 0;
mjr 77:0b96f6867312 120 this->val2 = 0;
mjr 77:0b96f6867312 121 this->IRCommand2 = 0;
mjr 40:cc0d9814522b 122 }
mjr 40:cc0d9814522b 123
mjr 40:cc0d9814522b 124 } __attribute__((packed));
mjr 40:cc0d9814522b 125
mjr 33:d832bcab089e 126
mjr 65:739875521aae 127 // maximum number of input button mappings in configuration
mjr 65:739875521aae 128 const int MAX_BUTTONS = 48;
mjr 65:739875521aae 129
mjr 65:739875521aae 130 // extra slots for virtual buttons (ZB Launch Ball)
mjr 65:739875521aae 131 const int VIRTUAL_BUTTONS = 1; // total number of buttons
mjr 65:739875521aae 132 const int ZBL_BUTTON_CFG = MAX_BUTTONS; // index of ZB Launch Ball slot
mjr 33:d832bcab089e 133
mjr 35:e959ffba78fd 134 // LedWiz output port type codes
mjr 35:e959ffba78fd 135 // These values are part of the external USB interface
mjr 35:e959ffba78fd 136 const int PortTypeDisabled = 0; // port is disabled - not visible to LedWiz/DOF host
mjr 35:e959ffba78fd 137 const int PortTypeGPIOPWM = 1; // GPIO port, PWM enabled
mjr 35:e959ffba78fd 138 const int PortTypeGPIODig = 2; // GPIO port, digital out
mjr 35:e959ffba78fd 139 const int PortTypeTLC5940 = 3; // TLC5940 port
mjr 35:e959ffba78fd 140 const int PortType74HC595 = 4; // 74HC595 port
mjr 53:9b2611964afc 141 const int PortTypeVirtual = 5; // Virtual port - visible to host software, but not connected
mjr 53:9b2611964afc 142 // to a physical output
mjr 17:ab3cec0c8bf4 143
mjr 35:e959ffba78fd 144 // LedWiz output port flag bits
mjr 38:091e511ce8a0 145 const uint8_t PortFlagActiveLow = 0x01; // physical output is active-low
mjr 38:091e511ce8a0 146 const uint8_t PortFlagNoisemaker = 0x02; // noisemaker device - disable when night mode is engaged
mjr 40:cc0d9814522b 147 const uint8_t PortFlagGamma = 0x04; // apply gamma correction to this output
mjr 35:e959ffba78fd 148
mjr 35:e959ffba78fd 149 // maximum number of output ports
mjr 48:058ace2aed1d 150 const int MAX_OUT_PORTS = 128;
mjr 33:d832bcab089e 151
mjr 38:091e511ce8a0 152 // port configuration data
mjr 38:091e511ce8a0 153 struct LedWizPortCfg
mjr 38:091e511ce8a0 154 {
mjr 38:091e511ce8a0 155 uint8_t typ; // port type: a PortTypeXxx value
mjr 38:091e511ce8a0 156 uint8_t pin; // physical output pin: for a GPIO port, this is an index in the
mjr 38:091e511ce8a0 157 // USB-to-PinName mapping list; for a TLC5940 or 74HC595 port, it's
mjr 38:091e511ce8a0 158 // the output number, starting from 0 for OUT0 on the first chip in
mjr 38:091e511ce8a0 159 // the daisy chain. For inactive and virtual ports, it's unused.
mjr 38:091e511ce8a0 160 uint8_t flags; // flags: a combination of PortFlagXxx values
mjr 40:cc0d9814522b 161
mjr 40:cc0d9814522b 162 void set(uint8_t typ, uint8_t pin, uint8_t flags = 0)
mjr 40:cc0d9814522b 163 {
mjr 40:cc0d9814522b 164 this->typ = typ;
mjr 40:cc0d9814522b 165 this->pin = pin;
mjr 40:cc0d9814522b 166 this->flags = flags;
mjr 40:cc0d9814522b 167 }
mjr 40:cc0d9814522b 168
mjr 77:0b96f6867312 169 } __attribute__ ((packed));
mjr 77:0b96f6867312 170
mjr 77:0b96f6867312 171 // IR command configuration flags
mjr 77:0b96f6867312 172 const uint8_t IRFlagTVON = 0x01; // send command at TV ON time
mjr 77:0b96f6867312 173 const uint8_t IRFlagDittos = 0x02; // use "ditto" codes on send
mjr 77:0b96f6867312 174
mjr 77:0b96f6867312 175 // IR command configuration data
mjr 77:0b96f6867312 176 struct IRCommandCfg
mjr 77:0b96f6867312 177 {
mjr 77:0b96f6867312 178 uint8_t flags; // flags: a combination of IRFlagXxx values
mjr 77:0b96f6867312 179 uint8_t keytype; // key type to send when IR command is received
mjr 77:0b96f6867312 180 uint8_t keycode; // key code to send when IR command is received
mjr 77:0b96f6867312 181 uint8_t protocol; // IR protocol ID (see IRRemote/IRProtocolID.h)
mjr 77:0b96f6867312 182 struct
mjr 77:0b96f6867312 183 {
mjr 77:0b96f6867312 184 uint32_t lo; // low 32 bits of code
mjr 77:0b96f6867312 185 uint32_t hi; // high 32 bits of code
mjr 77:0b96f6867312 186 } code; // 64-bit command code (protocol-specific; see IRProtocols.h)
mjr 77:0b96f6867312 187 } __attribute__ ((packed));
mjr 77:0b96f6867312 188
mjr 77:0b96f6867312 189 // Maximum number of IR commands
mjr 77:0b96f6867312 190 const int MAX_IR_CODES = 16;
mjr 38:091e511ce8a0 191
mjr 38:091e511ce8a0 192
mjr 53:9b2611964afc 193 // Convert a physical pin name to a wire pin name
mjr 53:9b2611964afc 194 #define PINNAME_TO_WIRE(p) \
mjr 53:9b2611964afc 195 uint8_t((p) == NC ? 0xFF : \
mjr 53:9b2611964afc 196 (((p) & 0xF000 ) >> (PORT_SHIFT - 5)) | (((p) & 0xFF) >> 2))
mjr 53:9b2611964afc 197
mjr 35:e959ffba78fd 198 struct Config
mjr 35:e959ffba78fd 199 {
mjr 35:e959ffba78fd 200 // set all values to factory defaults
mjr 35:e959ffba78fd 201 void setFactoryDefaults()
mjr 35:e959ffba78fd 202 {
mjr 35:e959ffba78fd 203 // By default, pretend to be LedWiz unit #8. This can be from 1 to 16. Real
mjr 35:e959ffba78fd 204 // LedWiz units have their unit number set at the factory, and the vast majority
mjr 35:e959ffba78fd 205 // are set up as unit #1, since that's the default for anyone who doesn't ask
mjr 35:e959ffba78fd 206 // for a different setting. It seems rare for anyone to use more than one unit
mjr 35:e959ffba78fd 207 // in a pin cab, but for the few who do, the others will probably be numbered
mjr 35:e959ffba78fd 208 // sequentially as #2, #3, etc. It seems safe to assume that no one out there
mjr 48:058ace2aed1d 209 // has a unit #8, so we'll use that as our default. This can be changed from
mjr 48:058ace2aed1d 210 // the config tool, but for the sake of convenience, it's better to pick a
mjr 48:058ace2aed1d 211 // default that most people won't have to change.
mjr 54:fd77a6b2f76c 212 usbVendorID = 0xFAFA; // LedWiz vendor code
mjr 48:058ace2aed1d 213 usbProductID = 0x00F7; // LedWiz product code for unit #8
mjr 61:3c7e6e9ec355 214
mjr 55:4db125cd11a0 215 // Set the default Pinscape unit number to #1. This is a separate identifier
mjr 55:4db125cd11a0 216 // from the LedWiz ID, so you don't have to worry about making this different
mjr 55:4db125cd11a0 217 // from your LedWiz units. Each Pinscape unit should have a unique value for
mjr 55:4db125cd11a0 218 // this ID, though.
mjr 55:4db125cd11a0 219 //
mjr 55:4db125cd11a0 220 // Note that Pinscape unit #1 corresponds to DOF Pinscape #51, PS 2 -> DOF 52,
mjr 55:4db125cd11a0 221 // and so on - just add 50 to get the DOF ID.
mjr 55:4db125cd11a0 222 psUnitNo = 1;
mjr 35:e959ffba78fd 223
mjr 51:57eb311faafa 224 // set a disconnect reboot timeout of 10 seconds by default
mjr 55:4db125cd11a0 225 disconnectRebootTimeout = 10;
mjr 51:57eb311faafa 226
mjr 35:e959ffba78fd 227 // enable joystick reports
mjr 35:e959ffba78fd 228 joystickEnabled = true;
mjr 35:e959ffba78fd 229
mjr 35:e959ffba78fd 230 // assume standard orientation, with USB ports toward front of cabinet
mjr 35:e959ffba78fd 231 orientation = OrientationFront;
mjr 25:e22b88bd783a 232
mjr 52:8298b2a73eb2 233 // assume a basic setup with no expansion boards
mjr 53:9b2611964afc 234 expan.typ = 0;
mjr 53:9b2611964afc 235 expan.vsn = 0;
mjr 53:9b2611964afc 236 memset(expan.ext, 0, sizeof(expan.ext));
mjr 52:8298b2a73eb2 237
mjr 35:e959ffba78fd 238 // assume no plunger is attached
mjr 77:0b96f6867312 239 plunger.enabled = 0x00;
mjr 35:e959ffba78fd 240 plunger.sensorType = PlungerType_None;
mjr 35:e959ffba78fd 241
mjr 55:4db125cd11a0 242 #if TEST_CONFIG_EXPAN || STANDARD_CONFIG
mjr 77:0b96f6867312 243 plunger.enabled = 0x01;
mjr 43:7a6364d82a41 244 plunger.sensorType = PlungerType_TSL1410RS;
mjr 53:9b2611964afc 245 plunger.sensorPin[0] = PINNAME_TO_WIRE(PTE20); // SI
mjr 53:9b2611964afc 246 plunger.sensorPin[1] = PINNAME_TO_WIRE(PTE21); // SCLK
mjr 53:9b2611964afc 247 plunger.sensorPin[2] = PINNAME_TO_WIRE(PTB0); // AO1 = PTB0 = ADC0_SE8
mjr 53:9b2611964afc 248 plunger.sensorPin[3] = PINNAME_TO_WIRE(PTE22); // AO2 (parallel mode) = PTE22 = ADC0_SE3
mjr 43:7a6364d82a41 249 #endif
mjr 43:7a6364d82a41 250
mjr 48:058ace2aed1d 251 // default plunger calibration button settings
mjr 55:4db125cd11a0 252 plunger.cal.features = 0x03; // 0x01 = enable button, 0x02 = enable indicator lamp
mjr 55:4db125cd11a0 253 plunger.cal.btn = PINNAME_TO_WIRE(PTE29); // button input (DigitalIn port)
mjr 55:4db125cd11a0 254 plunger.cal.led = PINNAME_TO_WIRE(PTE23); // button output (DigitalOut port)
mjr 35:e959ffba78fd 255
mjr 44:b5ac89b9cd5d 256 // set the default plunger calibration
mjr 44:b5ac89b9cd5d 257 plunger.cal.setDefaults();
mjr 35:e959ffba78fd 258
mjr 35:e959ffba78fd 259 // disable the ZB Launch Ball by default
mjr 53:9b2611964afc 260 plunger.zbLaunchBall.port = 0; // 0 = disabled
mjr 65:739875521aae 261 plunger.zbLaunchBall.keytype = BtnTypeKey; // keyboard key
mjr 61:3c7e6e9ec355 262 plunger.zbLaunchBall.keycode = 0x28; // USB keyboard scan code for Enter key
mjr 61:3c7e6e9ec355 263 plunger.zbLaunchBall.pushDistance = 63; // 63/1000 in == .063" == about 1/16"
mjr 35:e959ffba78fd 264
mjr 35:e959ffba78fd 265 // assume no TV ON switch
mjr 53:9b2611964afc 266 TVON.statusPin = PINNAME_TO_WIRE(NC);
mjr 53:9b2611964afc 267 TVON.latchPin = PINNAME_TO_WIRE(NC);
mjr 53:9b2611964afc 268 TVON.relayPin = PINNAME_TO_WIRE(NC);
mjr 53:9b2611964afc 269 TVON.delayTime = 700; // 7 seconds
mjr 55:4db125cd11a0 270
mjr 55:4db125cd11a0 271 #if TEST_CONFIG_EXPAN
mjr 55:4db125cd11a0 272 // expansion board TV ON wiring
mjr 53:9b2611964afc 273 TVON.statusPin = PINNAME_TO_WIRE(PTD2);
mjr 53:9b2611964afc 274 TVON.latchPin = PINNAME_TO_WIRE(PTE0);
mjr 53:9b2611964afc 275 TVON.relayPin = PINNAME_TO_WIRE(PTD3);
mjr 53:9b2611964afc 276 TVON.delayTime = 700; // 7 seconds
mjr 38:091e511ce8a0 277 #endif
mjr 53:9b2611964afc 278
mjr 53:9b2611964afc 279 // assume no night mode switch or indicator lamp
mjr 53:9b2611964afc 280 nightMode.btn = 0;
mjr 53:9b2611964afc 281 nightMode.flags = 0;
mjr 53:9b2611964afc 282 nightMode.port = 0;
mjr 35:e959ffba78fd 283
mjr 35:e959ffba78fd 284 // assume no TLC5940 chips
mjr 35:e959ffba78fd 285 tlc5940.nchips = 0;
mjr 55:4db125cd11a0 286
mjr 55:4db125cd11a0 287 #if TEST_CONFIG_EXPAN
mjr 55:4db125cd11a0 288 // for expansion board testing purposes, assume the common setup
mjr 55:4db125cd11a0 289 // with one main board and one power board
mjr 48:058ace2aed1d 290 tlc5940.nchips = 4;
mjr 38:091e511ce8a0 291 #endif
mjr 38:091e511ce8a0 292
mjr 55:4db125cd11a0 293 // Default TLC5940 pin assignments. Note that it's harmless to set
mjr 55:4db125cd11a0 294 // these to valid pins even if no TLC5940 chips are actually present,
mjr 55:4db125cd11a0 295 // since the main program won't allocate the connections if 'nchips'
mjr 55:4db125cd11a0 296 // is zero. This means that the pins are free to be used for other
mjr 55:4db125cd11a0 297 // purposes (such as output ports) if not using TLC5940 chips.
mjr 53:9b2611964afc 298 tlc5940.sin = PINNAME_TO_WIRE(PTC6);
mjr 53:9b2611964afc 299 tlc5940.sclk = PINNAME_TO_WIRE(PTC5);
mjr 53:9b2611964afc 300 tlc5940.xlat = PINNAME_TO_WIRE(PTC10);
mjr 59:94eb9265b6d7 301 tlc5940.blank = PINNAME_TO_WIRE(PTC7);
mjr 59:94eb9265b6d7 302 #if TEST_KEEP_PRINTF
mjr 59:94eb9265b6d7 303 tlc5940.gsclk = PINNAME_TO_WIRE(PTA13); // PTA1 is reserved for SDA printf()
mjr 59:94eb9265b6d7 304 #else
mjr 53:9b2611964afc 305 tlc5940.gsclk = PINNAME_TO_WIRE(PTA1);
mjr 59:94eb9265b6d7 306 #endif
mjr 35:e959ffba78fd 307
mjr 35:e959ffba78fd 308 // assume no 74HC595 chips
mjr 35:e959ffba78fd 309 hc595.nchips = 0;
mjr 55:4db125cd11a0 310
mjr 55:4db125cd11a0 311 #if TEST_CONFIG_EXPAN
mjr 55:4db125cd11a0 312 // for expansion board testing purposes, assume one chime board
mjr 48:058ace2aed1d 313 hc595.nchips = 1;
mjr 40:cc0d9814522b 314 #endif
mjr 40:cc0d9814522b 315
mjr 55:4db125cd11a0 316 // Default 74HC595 pin assignments. As with the TLC5940 pins, it's
mjr 55:4db125cd11a0 317 // harmless to assign pins here even if no 74HC595 chips are used,
mjr 55:4db125cd11a0 318 // since the main program won't actually allocate the pins if 'nchips'
mjr 55:4db125cd11a0 319 // is zero.
mjr 53:9b2611964afc 320 hc595.sin = PINNAME_TO_WIRE(PTA5);
mjr 53:9b2611964afc 321 hc595.sclk = PINNAME_TO_WIRE(PTA4);
mjr 53:9b2611964afc 322 hc595.latch = PINNAME_TO_WIRE(PTA12);
mjr 53:9b2611964afc 323 hc595.ena = PINNAME_TO_WIRE(PTD4);
mjr 38:091e511ce8a0 324
mjr 77:0b96f6867312 325
mjr 77:0b96f6867312 326 // Default IR hardware pin assignments. On the expansion boards,
mjr 77:0b96f6867312 327 // the sensor is connected to PTA13, and the emitter LED is on PTC9.
mjr 77:0b96f6867312 328 #if TEST_CONFIG_EXPAN
mjr 77:0b96f6867312 329 IR.sensor = PINNAME_TO_WIRE(PTA13);
mjr 77:0b96f6867312 330 IR.emitter = PINNAME_TO_WIRE(PTC9);
mjr 77:0b96f6867312 331 #else
mjr 77:0b96f6867312 332 IR.sensor = PINNAME_TO_WIRE(NC);
mjr 77:0b96f6867312 333 IR.emitter = PINNAME_TO_WIRE(NC);
mjr 77:0b96f6867312 334 #endif
mjr 77:0b96f6867312 335
mjr 77:0b96f6867312 336 // clear out all IR slots
mjr 77:0b96f6867312 337 memset(IRCommand, 0, sizeof(IRCommand));
mjr 77:0b96f6867312 338 for (int i = 0 ; i < MAX_IR_CODES ; ++i)
mjr 77:0b96f6867312 339 {
mjr 77:0b96f6867312 340 IRCommand[i].protocol = 0;
mjr 77:0b96f6867312 341 IRCommand[i].keytype = BtnTypeNone;
mjr 77:0b96f6867312 342 }
mjr 77:0b96f6867312 343
mjr 35:e959ffba78fd 344 // initially configure with no LedWiz output ports
mjr 35:e959ffba78fd 345 outPort[0].typ = PortTypeDisabled;
mjr 66:2e3583fbd2f4 346
mjr 66:2e3583fbd2f4 347 // initially configure with no shift key
mjr 66:2e3583fbd2f4 348 shiftButton = 0;
mjr 53:9b2611964afc 349
mjr 35:e959ffba78fd 350 // initially configure with no input buttons
mjr 35:e959ffba78fd 351 for (int i = 0 ; i < MAX_BUTTONS ; ++i)
mjr 53:9b2611964afc 352 button[i].set(PINNAME_TO_WIRE(NC), BtnTypeNone, 0);
mjr 38:091e511ce8a0 353
mjr 55:4db125cd11a0 354 #if STANDARD_CONFIG | TEST_CONFIG_EXPAN
mjr 55:4db125cd11a0 355 // For the standard configuration, assign 24 input ports to
mjr 55:4db125cd11a0 356 // joystick buttons 1-24. Assign the same GPIO pins used
mjr 55:4db125cd11a0 357 // in the original v1 default configuration. For expansion
mjr 55:4db125cd11a0 358 // board testing purposes, also assign the input ports, with
mjr 55:4db125cd11a0 359 // the noted differences.
mjr 38:091e511ce8a0 360 for (int i = 0 ; i < 24 ; ++i) {
mjr 55:4db125cd11a0 361 static const int bp[] = {
mjr 53:9b2611964afc 362 PINNAME_TO_WIRE(PTC2), // 1
mjr 53:9b2611964afc 363 PINNAME_TO_WIRE(PTB3), // 2
mjr 53:9b2611964afc 364 PINNAME_TO_WIRE(PTB2), // 3
mjr 53:9b2611964afc 365 PINNAME_TO_WIRE(PTB1), // 4
mjr 53:9b2611964afc 366 PINNAME_TO_WIRE(PTE30), // 5
mjr 48:058ace2aed1d 367 #if TEST_CONFIG_EXPAN
mjr 55:4db125cd11a0 368 PINNAME_TO_WIRE(PTC11), // 6 - expansion boards use PTC11 for this, since PTE22
mjr 55:4db125cd11a0 369 // is reserved for a plunger connection
mjr 55:4db125cd11a0 370 #elif STANDARD_CONFIG
mjr 55:4db125cd11a0 371 PINNAME_TO_WIRE(PTE22), // 6 - original standalone setup uses PTE22
mjr 48:058ace2aed1d 372 #endif
mjr 53:9b2611964afc 373 PINNAME_TO_WIRE(PTE5), // 7
mjr 53:9b2611964afc 374 PINNAME_TO_WIRE(PTE4), // 8
mjr 53:9b2611964afc 375 PINNAME_TO_WIRE(PTE3), // 9
mjr 53:9b2611964afc 376 PINNAME_TO_WIRE(PTE2), // 10
mjr 53:9b2611964afc 377 PINNAME_TO_WIRE(PTB11), // 11
mjr 53:9b2611964afc 378 PINNAME_TO_WIRE(PTB10), // 12
mjr 53:9b2611964afc 379 PINNAME_TO_WIRE(PTB9), // 13
mjr 53:9b2611964afc 380 PINNAME_TO_WIRE(PTB8), // 14
mjr 53:9b2611964afc 381 PINNAME_TO_WIRE(PTC12), // 15
mjr 53:9b2611964afc 382 PINNAME_TO_WIRE(PTC13), // 16
mjr 53:9b2611964afc 383 PINNAME_TO_WIRE(PTC16), // 17
mjr 53:9b2611964afc 384 PINNAME_TO_WIRE(PTC17), // 18
mjr 53:9b2611964afc 385 PINNAME_TO_WIRE(PTA16), // 19
mjr 53:9b2611964afc 386 PINNAME_TO_WIRE(PTA17), // 20
mjr 53:9b2611964afc 387 PINNAME_TO_WIRE(PTE31), // 21
mjr 53:9b2611964afc 388 PINNAME_TO_WIRE(PTD6), // 22
mjr 53:9b2611964afc 389 PINNAME_TO_WIRE(PTD7), // 23
mjr 53:9b2611964afc 390 PINNAME_TO_WIRE(PTE1) // 24
mjr 40:cc0d9814522b 391 };
mjr 48:058ace2aed1d 392 button[i].set(bp[i],
mjr 48:058ace2aed1d 393 #if TEST_CONFIG_EXPAN
mjr 55:4db125cd11a0 394 // For expansion board testing only, assign the inputs
mjr 55:4db125cd11a0 395 // to keyboard keys A, B, etc. This isn't useful; it's
mjr 55:4db125cd11a0 396 // just for testing purposes. Note that the USB key code
mjr 55:4db125cd11a0 397 // for "A" is 4, "B" is 5, and so on sequentially through
mjr 55:4db125cd11a0 398 // the alphabet.
mjr 55:4db125cd11a0 399 BtnTypeKey, i+4);
mjr 55:4db125cd11a0 400 #elif STANDARD_CONFIG
mjr 55:4db125cd11a0 401 // For the standard configuration, assign the input to
mjr 55:4db125cd11a0 402 // joystick buttons 1-24, as in the original v1 default
mjr 55:4db125cd11a0 403 // configuration.
mjr 55:4db125cd11a0 404 BtnTypeJoystick, i+1);
mjr 48:058ace2aed1d 405 #endif
mjr 48:058ace2aed1d 406
mjr 38:091e511ce8a0 407 }
mjr 38:091e511ce8a0 408 #endif
mjr 38:091e511ce8a0 409
mjr 55:4db125cd11a0 410 #if TEST_CONFIG_EXPAN
mjr 55:4db125cd11a0 411 // For testing purposes, configure the basic complement of
mjr 55:4db125cd11a0 412 // expansion board ports. AS MENTIONED ABOVE, THIS IS PURELY FOR
mjr 55:4db125cd11a0 413 // TESTING. DON'T USE THIS METHOD TO CONFIGURE YOUR EXPANSION
mjr 55:4db125cd11a0 414 // BOARDS FOR ACTUAL DEPLOYMENT. It's much easier and cleaner
mjr 55:4db125cd11a0 415 // to use the unmodified standard build, and customize your
mjr 55:4db125cd11a0 416 // installation with the Pinscape Config Tool on Windows.
mjr 40:cc0d9814522b 417 //
mjr 55:4db125cd11a0 418 // For this testing setup, we'll configure one main board, one
mjr 55:4db125cd11a0 419 // power board, and one chime board. The *physical* ports on
mjr 55:4db125cd11a0 420 // the board are shown below. The logical (LedWiz/DOF) numbering
mjr 55:4db125cd11a0 421 // ISN'T sequential through the physical ports, because we want
mjr 55:4db125cd11a0 422 // to arrange the DOF ports so that the most important and most
mjr 55:4db125cd11a0 423 // common toys are assigned to ports 1-32. Those ports are
mjr 55:4db125cd11a0 424 // special because they're accessible to ALL software on the PC,
mjr 55:4db125cd11a0 425 // including older LedWiz-only software such as Future Pinball.
mjr 55:4db125cd11a0 426 // Ports above 32 are accessible only to modern DOF software,
mjr 55:4db125cd11a0 427 // like Visual Pinball and PinballX.
mjr 40:cc0d9814522b 428 //
mjr 40:cc0d9814522b 429 // Main board
mjr 40:cc0d9814522b 430 // TLC ports 0-15 -> flashers
mjr 40:cc0d9814522b 431 // TLC ports 16 -> strobe
mjr 40:cc0d9814522b 432 // TLC ports 17-31 -> flippers
mjr 40:cc0d9814522b 433 // Dig GPIO PTC8 -> knocker (timer-protected outputs)
mjr 40:cc0d9814522b 434 //
mjr 40:cc0d9814522b 435 // Power board:
mjr 40:cc0d9814522b 436 // TLC ports 32-63 -> general purpose outputs
mjr 40:cc0d9814522b 437 //
mjr 40:cc0d9814522b 438 // Chime board:
mjr 40:cc0d9814522b 439 // HC595 ports 0-7 -> timer-protected outputs
mjr 40:cc0d9814522b 440 //
mjr 38:091e511ce8a0 441 {
mjr 38:091e511ce8a0 442 int n = 0;
mjr 40:cc0d9814522b 443
mjr 40:cc0d9814522b 444 // 1-15 = flashers (TLC ports 0-15)
mjr 40:cc0d9814522b 445 // 16 = strobe (TLC port 15)
mjr 40:cc0d9814522b 446 for (int i = 0 ; i < 16 ; ++i)
mjr 40:cc0d9814522b 447 outPort[n++].set(PortTypeTLC5940, i, PortFlagGamma);
mjr 40:cc0d9814522b 448
mjr 53:9b2611964afc 449 // 17 = knocker (PTC8)
mjr 53:9b2611964afc 450 outPort[n++].set(PortTypeGPIODig, PINNAME_TO_WIRE(PTC8));
mjr 35:e959ffba78fd 451
mjr 40:cc0d9814522b 452 // 18-49 = power board outputs 1-32 (TLC ports 32-63)
mjr 40:cc0d9814522b 453 for (int i = 0 ; i < 32 ; ++i)
mjr 40:cc0d9814522b 454 outPort[n++].set(PortTypeTLC5940, i+32);
mjr 40:cc0d9814522b 455
mjr 40:cc0d9814522b 456 // 50-65 = flipper RGB (TLC ports 16-31)
mjr 40:cc0d9814522b 457 for (int i = 0 ; i < 16 ; ++i)
mjr 40:cc0d9814522b 458 outPort[n++].set(PortTypeTLC5940, i+16, PortFlagGamma);
mjr 59:94eb9265b6d7 459
mjr 40:cc0d9814522b 460 // 66-73 = chime board ports 1-8 (74HC595 ports 0-7)
mjr 40:cc0d9814522b 461 for (int i = 0 ; i < 8 ; ++i)
mjr 40:cc0d9814522b 462 outPort[n++].set(PortType74HC595, i);
mjr 59:94eb9265b6d7 463
mjr 40:cc0d9814522b 464 // set Disabled to signify end of configured outputs
mjr 38:091e511ce8a0 465 outPort[n].typ = PortTypeDisabled;
mjr 38:091e511ce8a0 466 }
mjr 38:091e511ce8a0 467 #endif
mjr 48:058ace2aed1d 468
mjr 55:4db125cd11a0 469 #if STANDARD_CONFIG
mjr 55:4db125cd11a0 470 //
mjr 55:4db125cd11a0 471 // For the standard build, set up the original complement
mjr 55:4db125cd11a0 472 // of 22 ports from the v1 default onfiguration.
mjr 55:4db125cd11a0 473 //
mjr 55:4db125cd11a0 474 // IMPORTANT! As mentioned above, don't edit this file to
mjr 55:4db125cd11a0 475 // customize this for your machine. Instead, use the unmodified
mjr 55:4db125cd11a0 476 // standard build, and customize your installation using the
mjr 55:4db125cd11a0 477 // Pinscape Config Tool on Windows.
mjr 55:4db125cd11a0 478 //
mjr 48:058ace2aed1d 479 #if TEST_KEEP_PRINTF
mjr 55:4db125cd11a0 480 outPort[ 0].set(PortTypeVirtual, PINNAME_TO_WIRE(NC)); // port 1 = NC to keep debug printf (PTA1 is SDA UART)
mjr 55:4db125cd11a0 481 outPort[ 1].set(PortTypeVirtual, PINNAME_TO_WIRE(NC)); // port 2 = NC to keep debug printf (PTA2 is SDA UART)
mjr 48:058ace2aed1d 482 #else
mjr 53:9b2611964afc 483 outPort[ 0].set(PortTypeGPIOPWM, PINNAME_TO_WIRE(PTA1)); // port 1 = PTA1
mjr 53:9b2611964afc 484 outPort[ 1].set(PortTypeGPIOPWM, PINNAME_TO_WIRE(PTA2)); // port 2 = PTA2
mjr 48:058ace2aed1d 485 #endif
mjr 53:9b2611964afc 486 outPort[ 2].set(PortTypeGPIOPWM, PINNAME_TO_WIRE(PTD4)); // port 3 = PTD4
mjr 53:9b2611964afc 487 outPort[ 3].set(PortTypeGPIOPWM, PINNAME_TO_WIRE(PTA12)); // port 4 = PTA12
mjr 53:9b2611964afc 488 outPort[ 4].set(PortTypeGPIOPWM, PINNAME_TO_WIRE(PTA4)); // port 5 = PTA4
mjr 53:9b2611964afc 489 outPort[ 5].set(PortTypeGPIOPWM, PINNAME_TO_WIRE(PTA5)); // port 6 = PTA5
mjr 53:9b2611964afc 490 outPort[ 6].set(PortTypeGPIOPWM, PINNAME_TO_WIRE(PTA13)); // port 7 = PTA13
mjr 53:9b2611964afc 491 outPort[ 7].set(PortTypeGPIOPWM, PINNAME_TO_WIRE(PTD5)); // port 8 = PTD5
mjr 53:9b2611964afc 492 outPort[ 8].set(PortTypeGPIOPWM, PINNAME_TO_WIRE(PTD0)); // port 9 = PTD0
mjr 53:9b2611964afc 493 outPort[ 9].set(PortTypeGPIOPWM, PINNAME_TO_WIRE(PTD3)); // port 10 = PTD3
mjr 53:9b2611964afc 494 outPort[10].set(PortTypeGPIODig, PINNAME_TO_WIRE(PTD2)); // port 11 = PTD2
mjr 53:9b2611964afc 495 outPort[11].set(PortTypeGPIODig, PINNAME_TO_WIRE(PTC8)); // port 12 = PTC8
mjr 53:9b2611964afc 496 outPort[12].set(PortTypeGPIODig, PINNAME_TO_WIRE(PTC9)); // port 13 = PTC9
mjr 53:9b2611964afc 497 outPort[13].set(PortTypeGPIODig, PINNAME_TO_WIRE(PTC7)); // port 14 = PTC7
mjr 53:9b2611964afc 498 outPort[14].set(PortTypeGPIODig, PINNAME_TO_WIRE(PTC0)); // port 15 = PTC0
mjr 53:9b2611964afc 499 outPort[15].set(PortTypeGPIODig, PINNAME_TO_WIRE(PTC3)); // port 16 = PTC3
mjr 53:9b2611964afc 500 outPort[16].set(PortTypeGPIODig, PINNAME_TO_WIRE(PTC4)); // port 17 = PTC4
mjr 53:9b2611964afc 501 outPort[17].set(PortTypeGPIODig, PINNAME_TO_WIRE(PTC5)); // port 18 = PTC5
mjr 53:9b2611964afc 502 outPort[18].set(PortTypeGPIODig, PINNAME_TO_WIRE(PTC6)); // port 19 = PTC6
mjr 53:9b2611964afc 503 outPort[19].set(PortTypeGPIODig, PINNAME_TO_WIRE(PTC10)); // port 20 = PTC10
mjr 53:9b2611964afc 504 outPort[20].set(PortTypeGPIODig, PINNAME_TO_WIRE(PTC11)); // port 21 = PTC11
mjr 53:9b2611964afc 505 outPort[21].set(PortTypeGPIODig, PINNAME_TO_WIRE(PTE0)); // port 22 = PTE0
mjr 48:058ace2aed1d 506 #endif
mjr 35:e959ffba78fd 507 }
mjr 35:e959ffba78fd 508
mjr 35:e959ffba78fd 509 // --- USB DEVICE CONFIGURATION ---
mjr 35:e959ffba78fd 510
mjr 35:e959ffba78fd 511 // USB device identification - vendor ID and product ID. For LedLWiz
mjr 35:e959ffba78fd 512 // emulation, use vendor ID 0xFAFA and product ID 0x00EF + unit#, where
mjr 35:e959ffba78fd 513 // unit# is the nominal LedWiz unit number from 1 to 16. Alternatively,
mjr 35:e959ffba78fd 514 // if LedWiz emulation isn't desired or causes any driver conflicts on
mjr 35:e959ffba78fd 515 // the host, we have a private Pinscape assignment as vendor ID 0x1209
mjr 35:e959ffba78fd 516 // and product ID 0xEAEA (registered with http://pid.codes, a registry
mjr 35:e959ffba78fd 517 // for open-source USB projects).
mjr 35:e959ffba78fd 518 uint16_t usbVendorID;
mjr 35:e959ffba78fd 519 uint16_t usbProductID;
mjr 35:e959ffba78fd 520
mjr 35:e959ffba78fd 521 // Pinscape Controller unit number. This is the nominal unit number,
mjr 35:e959ffba78fd 522 // from 1 to 16. We report this in the status query; DOF uses it to
mjr 53:9b2611964afc 523 // distinguish among Pinscape units. Note that this doesn't affect
mjr 35:e959ffba78fd 524 // the LedWiz unit numbering, which is implied by the USB Product ID.
mjr 35:e959ffba78fd 525 uint8_t psUnitNo;
mjr 35:e959ffba78fd 526
mjr 35:e959ffba78fd 527 // Are joystick reports enabled? Joystick reports can be turned off, to
mjr 35:e959ffba78fd 528 // use the device as purely an output controller.
mjr 77:0b96f6867312 529 uint8_t joystickEnabled;
mjr 35:e959ffba78fd 530
mjr 51:57eb311faafa 531 // Timeout for rebooting the KL25Z when the connection is lost. On some
mjr 51:57eb311faafa 532 // hosts, the mbed USB stack has problems reconnecting after an initial
mjr 51:57eb311faafa 533 // connection is dropped. As a workaround, we can automatically reboot
mjr 51:57eb311faafa 534 // the KL25Z when it detects that it's no longer connected, after the
mjr 51:57eb311faafa 535 // interval set here expires. The timeout is in seconds; setting this
mjr 51:57eb311faafa 536 // to 0 disables the automatic reboot.
mjr 51:57eb311faafa 537 uint8_t disconnectRebootTimeout;
mjr 35:e959ffba78fd 538
mjr 35:e959ffba78fd 539 // --- ACCELEROMETER ---
mjr 35:e959ffba78fd 540
mjr 77:0b96f6867312 541 // accelerometer orientation (OrientationXxx value)
mjr 77:0b96f6867312 542 uint8_t orientation;
mjr 77:0b96f6867312 543
mjr 77:0b96f6867312 544 // dynamic range (AccelRangeXxx value)
mjr 77:0b96f6867312 545 uint8_t accelRange;
mjr 35:e959ffba78fd 546
mjr 35:e959ffba78fd 547
mjr 52:8298b2a73eb2 548 // --- EXPANSION BOARDS ---
mjr 52:8298b2a73eb2 549 struct
mjr 52:8298b2a73eb2 550 {
mjr 53:9b2611964afc 551 uint8_t typ; // expansion board set type:
mjr 53:9b2611964afc 552 // 1 -> Pinscape expansion boards
mjr 53:9b2611964afc 553 uint8_t vsn; // board set interface version
mjr 53:9b2611964afc 554 uint8_t ext[3]; // board set type-specific extended data
mjr 52:8298b2a73eb2 555
mjr 52:8298b2a73eb2 556 } expan;
mjr 52:8298b2a73eb2 557
mjr 52:8298b2a73eb2 558
mjr 35:e959ffba78fd 559 // --- PLUNGER CONFIGURATION ---
mjr 35:e959ffba78fd 560 struct
mjr 35:e959ffba78fd 561 {
mjr 77:0b96f6867312 562 // Plunger enabled/disabled. Note that we use the status flag
mjr 77:0b96f6867312 563 // bit 0x01 if enabled, 0x00 if disabled. This conveniently
mjr 77:0b96f6867312 564 // can be tested as though it's a bool, but should always be
mjr 77:0b96f6867312 565 // stored as 0x01 or 0x00 so that it can be OR'ed into the
mjr 77:0b96f6867312 566 // status report flag bits.
mjr 77:0b96f6867312 567 uint8_t enabled;
mjr 33:d832bcab089e 568
mjr 35:e959ffba78fd 569 // plunger sensor type
mjr 77:0b96f6867312 570 uint8_t sensorType;
mjr 35:e959ffba78fd 571
mjr 35:e959ffba78fd 572 // Plunger sensor pins. To accommodate a wide range of sensor types,
mjr 35:e959ffba78fd 573 // we keep a generic list of 4 pin assignments. The use of each pin
mjr 35:e959ffba78fd 574 // varies by sensor. The lists below are in order of the generic
mjr 35:e959ffba78fd 575 // pins; NC means that the pin isn't used by the sensor. Each pin's
mjr 35:e959ffba78fd 576 // GPIO usage is also listed. Certain usages limit which physical
mjr 35:e959ffba78fd 577 // pins can be assigned (e.g., AnalogIn or PwmOut).
mjr 35:e959ffba78fd 578 //
mjr 35:e959ffba78fd 579 // TSL1410R/1412R, serial: SI (DigitalOut), CLK (DigitalOut), AO (AnalogIn), NC
mjr 35:e959ffba78fd 580 // TSL1410R/1412R, parallel: SI (DigitalOut), CLK (DigitalOut), AO1 (AnalogIn), AO2 (AnalogIn)
mjr 35:e959ffba78fd 581 // Potentiometer: AO (AnalogIn), NC, NC, NC
mjr 35:e959ffba78fd 582 // AEDR8300: A (InterruptIn), B (InterruptIn), NC, NC
mjr 35:e959ffba78fd 583 // AS5304: A (InterruptIn), B (InterruptIn), NC, NC
mjr 53:9b2611964afc 584 //
mjr 53:9b2611964afc 585 // Note! These are stored in uint8_t WIRE format, not PinName format.
mjr 53:9b2611964afc 586 uint8_t sensorPin[4];
mjr 35:e959ffba78fd 587
mjr 53:9b2611964afc 588 // ZB LAUNCH BALL button setup.
mjr 35:e959ffba78fd 589 //
mjr 35:e959ffba78fd 590 // This configures the "ZB Launch Ball" feature in DOF, based on Zeb's (of
mjr 35:e959ffba78fd 591 // zebsboards.com) scheme for using a mechanical plunger as a Launch button.
mjr 35:e959ffba78fd 592 // Set the port to 0 to disable the feature.
mjr 35:e959ffba78fd 593 //
mjr 35:e959ffba78fd 594 // The port number is an LedWiz port number that we monitor for activation.
mjr 53:9b2611964afc 595 // This port isn't meant to be connected to a physical device, although it
mjr 53:9b2611964afc 596 // can be if desired. It's primarily to let the host tell the controller
mjr 53:9b2611964afc 597 // when the ZB Launch feature is active. The port numbering starts at 1;
mjr 53:9b2611964afc 598 // set this to zero to disable the feature.
mjr 35:e959ffba78fd 599 //
mjr 53:9b2611964afc 600 // The key type and code has the same meaning as for a button mapping. This
mjr 53:9b2611964afc 601 // sets the key input sent to the PC when the plunger triggers a launch when
mjr 53:9b2611964afc 602 // the mode is active. For example, set keytype=2 and keycode=0x28 to send
mjr 53:9b2611964afc 603 // the Enter key (which is the key almost all PC pinball software uses for
mjr 53:9b2611964afc 604 // plunger and Launch button input).
mjr 35:e959ffba78fd 605 //
mjr 40:cc0d9814522b 606 // The "push distance" is the distance, in 1/1000 inch units, for registering a
mjr 40:cc0d9814522b 607 // push on the plunger as a button push. If the player pushes the plunger
mjr 40:cc0d9814522b 608 // forward of the rest position by this amount, we'll treat it as pushing the
mjr 40:cc0d9814522b 609 // button, even if the player didn't pull back the plunger first. This lets
mjr 40:cc0d9814522b 610 // the player treat the plunger knob as a button for games where it's meaningful
mjr 35:e959ffba78fd 611 // to hold down the Launch button for specific intervals (e.g., "Championship
mjr 35:e959ffba78fd 612 // Pub").
mjr 35:e959ffba78fd 613 struct
mjr 35:e959ffba78fd 614 {
mjr 53:9b2611964afc 615 uint8_t port;
mjr 53:9b2611964afc 616 uint8_t keytype;
mjr 53:9b2611964afc 617 uint8_t keycode;
mjr 53:9b2611964afc 618 uint16_t pushDistance;
mjr 35:e959ffba78fd 619
mjr 35:e959ffba78fd 620 } zbLaunchBall;
mjr 35:e959ffba78fd 621
mjr 35:e959ffba78fd 622 // --- PLUNGER CALIBRATION ---
mjr 35:e959ffba78fd 623 struct
mjr 35:e959ffba78fd 624 {
mjr 35:e959ffba78fd 625 // has the plunger been calibrated?
mjr 53:9b2611964afc 626 bool calibrated;
mjr 55:4db125cd11a0 627
mjr 55:4db125cd11a0 628 // Feature enable mask:
mjr 55:4db125cd11a0 629 //
mjr 55:4db125cd11a0 630 // 0x01 = calibration button enabled
mjr 55:4db125cd11a0 631 // 0x02 = indicator light enabled
mjr 55:4db125cd11a0 632 uint8_t features;
mjr 35:e959ffba78fd 633
mjr 35:e959ffba78fd 634 // calibration button switch pin
mjr 53:9b2611964afc 635 uint8_t btn;
mjr 35:e959ffba78fd 636
mjr 35:e959ffba78fd 637 // calibration button indicator light pin
mjr 53:9b2611964afc 638 uint8_t led;
mjr 35:e959ffba78fd 639
mjr 48:058ace2aed1d 640 // Plunger calibration min, zero, and max. These are in terms of the
mjr 48:058ace2aed1d 641 // unsigned 16-bit scale (0x0000..0xffff) that we use for the raw sensor
mjr 48:058ace2aed1d 642 // readings.
mjr 48:058ace2aed1d 643 //
mjr 48:058ace2aed1d 644 // The zero point is the rest position (aka park position), where the
mjr 48:058ace2aed1d 645 // plunger is in equilibrium between the main spring and the barrel
mjr 48:058ace2aed1d 646 // spring. In the standard setup, the plunger can travel a small
mjr 48:058ace2aed1d 647 // distance forward of the rest position, because the barrel spring
mjr 48:058ace2aed1d 648 // can be compressed a bit. The minimum is the maximum forward point
mjr 48:058ace2aed1d 649 // where the barrel spring can't be compressed any further.
mjr 48:058ace2aed1d 650 uint16_t min;
mjr 48:058ace2aed1d 651 uint16_t zero;
mjr 48:058ace2aed1d 652 uint16_t max;
mjr 52:8298b2a73eb2 653
mjr 52:8298b2a73eb2 654 // Measured release time, in milliseconds.
mjr 52:8298b2a73eb2 655 uint8_t tRelease;
mjr 35:e959ffba78fd 656
mjr 44:b5ac89b9cd5d 657 // Reset the plunger calibration
mjr 44:b5ac89b9cd5d 658 void setDefaults()
mjr 35:e959ffba78fd 659 {
mjr 44:b5ac89b9cd5d 660 calibrated = false; // not calibrated
mjr 48:058ace2aed1d 661 min = 0; // assume we can go all the way forward...
mjr 48:058ace2aed1d 662 max = 0xffff; // ...and all the way back
mjr 48:058ace2aed1d 663 zero = max/6; // the rest position is usually around 1/2" back = 1/6 of total travel
mjr 52:8298b2a73eb2 664 tRelease = 65; // standard 65ms release time
mjr 44:b5ac89b9cd5d 665 }
mjr 44:b5ac89b9cd5d 666
mjr 44:b5ac89b9cd5d 667 // Begin calibration. This sets each limit to the worst
mjr 44:b5ac89b9cd5d 668 // case point - for example, we set the retracted position
mjr 44:b5ac89b9cd5d 669 // to all the way forward. Each actual reading that comes
mjr 44:b5ac89b9cd5d 670 // in is then checked against the current limit, and if it's
mjr 44:b5ac89b9cd5d 671 // outside of the limit, we reset the limit to the new reading.
mjr 44:b5ac89b9cd5d 672 void begin()
mjr 44:b5ac89b9cd5d 673 {
mjr 48:058ace2aed1d 674 min = 0; // we don't calibrate the maximum forward position, so keep this at zero
mjr 48:058ace2aed1d 675 zero = 0xffff; // set the zero position all the way back
mjr 48:058ace2aed1d 676 max = 0; // set the retracted position all the way forward
mjr 52:8298b2a73eb2 677 tRelease = 65; // revert to a default release time
mjr 35:e959ffba78fd 678 }
mjr 17:ab3cec0c8bf4 679
mjr 35:e959ffba78fd 680 } cal;
mjr 18:5e890ebd0023 681
mjr 35:e959ffba78fd 682 } plunger;
mjr 29:582472d0bc57 683
mjr 35:e959ffba78fd 684
mjr 35:e959ffba78fd 685 // --- TV ON SWITCH ---
mjr 35:e959ffba78fd 686 //
mjr 35:e959ffba78fd 687 // To use the TV ON switch feature, the special power sensing circuitry
mjr 35:e959ffba78fd 688 // implemented on the Expansion Board must be attached (or an equivalent
mjr 35:e959ffba78fd 689 // circuit, as described in the Build Guide). The circuitry lets us
mjr 35:e959ffba78fd 690 // detect power state changes on the secondary power supply.
mjr 35:e959ffba78fd 691 struct
mjr 35:e959ffba78fd 692 {
mjr 35:e959ffba78fd 693 // PSU2 power status sense (DigitalIn pin). This pin goes LOW when the
mjr 35:e959ffba78fd 694 // secondary power supply is turned off, and remains LOW until the LATCH
mjr 35:e959ffba78fd 695 // pin is raised high AND the secondary PSU is turned on. Once HIGH,
mjr 35:e959ffba78fd 696 // it remains HIGH as long as the secondary PSU is on.
mjr 53:9b2611964afc 697 uint8_t statusPin;
mjr 35:e959ffba78fd 698
mjr 35:e959ffba78fd 699 // PSU2 power status latch (DigitalOut pin)
mjr 53:9b2611964afc 700 uint8_t latchPin;
mjr 35:e959ffba78fd 701
mjr 35:e959ffba78fd 702 // TV ON relay pin (DigitalOut pin). This pin controls the TV switch
mjr 35:e959ffba78fd 703 // relay. Raising the pin HIGH turns the relay ON (energizes the coil).
mjr 53:9b2611964afc 704 uint8_t relayPin;
mjr 35:e959ffba78fd 705
mjr 40:cc0d9814522b 706 // TV ON delay time, in 1/100 second units. This is the interval between
mjr 40:cc0d9814522b 707 // sensing that the secondary power supply has turned on and pulsing the
mjr 40:cc0d9814522b 708 // TV ON switch relay.
mjr 40:cc0d9814522b 709 int delayTime;
mjr 35:e959ffba78fd 710
mjr 35:e959ffba78fd 711 } TVON;
mjr 35:e959ffba78fd 712
mjr 53:9b2611964afc 713 // --- Night Mode ---
mjr 53:9b2611964afc 714 struct
mjr 53:9b2611964afc 715 {
mjr 55:4db125cd11a0 716 uint8_t btn; // night mode button number (1..MAX_BUTTONS, 0 = no button)
mjr 53:9b2611964afc 717 uint8_t flags; // flags:
mjr 53:9b2611964afc 718 // 0x01 = on/off switch (if not set, it's a momentary button)
mjr 55:4db125cd11a0 719 uint8_t port; // indicator output port number (1..MAX_OUT_PORTS, 0 = no indicator)
mjr 53:9b2611964afc 720 } nightMode;
mjr 53:9b2611964afc 721
mjr 29:582472d0bc57 722
mjr 35:e959ffba78fd 723 // --- TLC5940NT PWM Controller Chip Setup ---
mjr 35:e959ffba78fd 724 struct
mjr 35:e959ffba78fd 725 {
mjr 35:e959ffba78fd 726 // number of TLC5940NT chips connected in daisy chain
mjr 35:e959ffba78fd 727 int nchips;
mjr 35:e959ffba78fd 728
mjr 53:9b2611964afc 729 // pin connections (wire pin IDs)
mjr 53:9b2611964afc 730 uint8_t sin; // Serial data - must connect to SPIO MOSI -> PTC6 or PTD2
mjr 53:9b2611964afc 731 uint8_t sclk; // Serial clock - must connect to SPIO SCLK -> PTC5 or PTD1
mjr 35:e959ffba78fd 732 // (but don't use PTD1, since it's hard-wired to the on-board blue LED)
mjr 53:9b2611964afc 733 uint8_t xlat; // XLAT (latch) signal - connect to any GPIO pin
mjr 53:9b2611964afc 734 uint8_t blank; // BLANK signal - connect to any GPIO pin
mjr 53:9b2611964afc 735 uint8_t gsclk; // Grayscale clock - must connect to a PWM-out capable pin
mjr 29:582472d0bc57 736
mjr 35:e959ffba78fd 737 } tlc5940;
mjr 35:e959ffba78fd 738
mjr 35:e959ffba78fd 739
mjr 35:e959ffba78fd 740 // --- 74HC595 Shift Register Setup ---
mjr 35:e959ffba78fd 741 struct
mjr 35:e959ffba78fd 742 {
mjr 35:e959ffba78fd 743 // number of 74HC595 chips attached in daisy chain
mjr 35:e959ffba78fd 744 int nchips;
mjr 35:e959ffba78fd 745
mjr 35:e959ffba78fd 746 // pin connections
mjr 53:9b2611964afc 747 uint8_t sin; // Serial data - use any GPIO pin
mjr 53:9b2611964afc 748 uint8_t sclk; // Serial clock - use any GPIO pin
mjr 53:9b2611964afc 749 uint8_t latch; // Latch - use any GPIO pin
mjr 53:9b2611964afc 750 uint8_t ena; // Enable signal - use any GPIO pin
mjr 35:e959ffba78fd 751
mjr 35:e959ffba78fd 752 } hc595;
mjr 77:0b96f6867312 753
mjr 77:0b96f6867312 754
mjr 77:0b96f6867312 755 // --- IR Remote Control Hardware Setup ---
mjr 77:0b96f6867312 756 struct
mjr 77:0b96f6867312 757 {
mjr 77:0b96f6867312 758 // sensor (receiver) GPIO input pin; must be interrupt-capable
mjr 77:0b96f6867312 759 uint8_t sensor;
mjr 77:0b96f6867312 760
mjr 77:0b96f6867312 761 // IR emitter LED GPIO output pin; must be PWM-capable
mjr 77:0b96f6867312 762 uint8_t emitter;
mjr 77:0b96f6867312 763 } IR;
mjr 77:0b96f6867312 764
mjr 77:0b96f6867312 765
mjr 35:e959ffba78fd 766 // --- Button Input Setup ---
mjr 65:739875521aae 767 ButtonCfg button[MAX_BUTTONS + VIRTUAL_BUTTONS] __attribute__((packed));
mjr 66:2e3583fbd2f4 768
mjr 66:2e3583fbd2f4 769 // Shift button index. If this is zero, there's no shift button. If this
mjr 66:2e3583fbd2f4 770 // is nonzero, it's the 1-based index of the shift button in the button[]
mjr 66:2e3583fbd2f4 771 // list.
mjr 66:2e3583fbd2f4 772 //
mjr 66:2e3583fbd2f4 773 // The shift button can also be used as a regular input key. If it is,
mjr 66:2e3583fbd2f4 774 // we DON'T send the input key to the PC as usual when the button is
mjr 66:2e3583fbd2f4 775 // pressed. Instead, we wait to see if the shift function is used:
mjr 66:2e3583fbd2f4 776 //
mjr 66:2e3583fbd2f4 777 // - If another button is pressed while the shift button is held down,
mjr 66:2e3583fbd2f4 778 // and the other button is programmed with a valid key for the shifted/
mjr 66:2e3583fbd2f4 779 // secondary meaning (i.e., typ2 is not BtnTypeNone), the shift function
mjr 66:2e3583fbd2f4 780 // is considered to have been used. We send the secondary meaning of
mjr 66:2e3583fbd2f4 781 // the other button to the PC. The shift key itself generates no PC
mjr 66:2e3583fbd2f4 782 // input in this case, since it has now performed its shift function.
mjr 66:2e3583fbd2f4 783 // Other shifted keys can also be pressed as long as the shift button
mjr 66:2e3583fbd2f4 784 // is held down, and they'll be sent to the PC with their shifted values
mjr 66:2e3583fbd2f4 785 // as well.
mjr 66:2e3583fbd2f4 786 //
mjr 66:2e3583fbd2f4 787 // - If the shift button is released before any other button with a
mjr 66:2e3583fbd2f4 788 // shifted key value is pressed, then the shift button press is taken to
mjr 66:2e3583fbd2f4 789 // be an ordinary key press instead of the shift function. In this case,
mjr 66:2e3583fbd2f4 790 // we report the shift button's key code to the PC when the button is
mjr 66:2e3583fbd2f4 791 // released. We can't report the key code to the PC until then because
mjr 66:2e3583fbd2f4 792 // we don't know until then that another key won't be pressed first.
mjr 66:2e3583fbd2f4 793 // The key press on release is a single timed pulse that's long enough
mjr 66:2e3583fbd2f4 794 // to register as a single key press on the PC, but not long enough to
mjr 66:2e3583fbd2f4 795 // trigger auto-repeat on the PC.
mjr 66:2e3583fbd2f4 796 uint8_t shiftButton;
mjr 17:ab3cec0c8bf4 797
mjr 35:e959ffba78fd 798 // --- LedWiz Output Port Setup ---
mjr 77:0b96f6867312 799 LedWizPortCfg outPort[MAX_OUT_PORTS] __attribute__ ((packed)); // LedWiz & extended output ports
mjr 48:058ace2aed1d 800
mjr 77:0b96f6867312 801 // --- IR Command Slots ---
mjr 77:0b96f6867312 802 IRCommandCfg IRCommand[MAX_IR_CODES] __attribute__ ((packed));
mjr 17:ab3cec0c8bf4 803 };
mjr 17:ab3cec0c8bf4 804
mjr 35:e959ffba78fd 805 #endif