mi mi
first 2016/02 SDFileSystemDMA inherited from Official SDFileSystem.
Dependents: SDFileSystemDMA-test DmdFullRGB_0_1
Fork of
SDFileSystemDMA
by 
mi mi
SDFileSystemDMA is enhanced SDFileSystem library for STM32 micros by using DMA functionality.
Max read transfer rate reaches over 2MByte/sec at 24MHz SPI clock if enough read buffer size is set.
Even though minimum read buffer size (512Byte) is set, read transfer rate will reach over 1MByte/sec at 24MHz SPI Clock.
( but depends on the ability of each SD card)
Test program is here.
https://developer.mbed.org/users/mimi3/code/SDFileSystemDMA-test/
Supported SPI port is shown below table.
(v): Verified. It works well.
(w): Probably it will work well. (not tested)
(c): Only compiled. (not tested)
(f): Over flash.
(r): Only read mode. (when _FS_READONLY==1)
(u) Under construction
(z): Dose not work.
Caution
If your board has SRAM less than or equal to 8KB, the buffer size must be set to 512 Bytes.
Supported Boards:
Cortex-M0
| Board | SRAM | SPI1 | SPI2 | SPI3 |
|---|---|---|---|---|
| NUCLEO-F030R8 | 8KB | (v) | ||
| DISCO-F051R8 | 8KB | (w) | ||
| 4KB | (f) | |||
| NUCLEO-F042K6 | 6KB | (r) | ||
| NUCLEO-F070RB | 16KB | (w) | ||
| NUCLEO-F072RB | 16KB | (w) | ||
| NUCLEO-F091RC | 32KB | (c) |
Cortex-L0
| Board | SRAM | SPI1 | SPI2 | SPI3 |
|---|---|---|---|---|
| DISCO-L053C8 | 8KB | (c) | ||
| NUCLEO-L053R8 | 8KB | (c) | ||
| NUCLEO-L073RZ | 20KB | (c) |
Cortex-M3
| Board | SRAM | SPI1 | SPI2 | SPI3 |
|---|---|---|---|---|
| DISCO-F100RB | 8KB | (v) | (v) | - |
| BLUEPILL-F103CB | 20KB | (w) | (w) | - |
| NUCLEO-F103RB | 20KB | (v) | (v) | - |
| NUCLEO-L152RE | 80KB | (v) | (w) | - |
| MOTE-L152RC | 32KB | (w) | (w) | - |
Cortex-M4
F3
| Board | SRAM | SPI1 | SPI2 | SPI3 |
|---|---|---|---|---|
| DISCO-F303VC | 40KB | - | (v) | (v) |
| NUCLEO-F303RE | 64KB | (w) | (w) | (w) |
| NUCLEO-F302R8 | 16KB | - | - | (c) |
| NUCLEO-F303K8 | 12KB | (c) | - | - |
| DISCO-F334C8 | 12KB | (c) | - | - |
| NUCLEO-F334R8 | 12KB | (c) | - | - |
F4
| Board | SPI1 | SPI2 | SPI3 |
|---|---|---|---|
| ELMO-F411RE | (w) | - | (w) |
| MTS-MDOT-F411RE | (u) | - | (u) |
| MTS-DRAGONFLY-F411RE | (w) | - | (w) |
| NUCLEO-F411RE | (v) | - | (v) |
| NUCLEO-F401RE | (w) | - | (w) |
| MTS-MDOT-F405RG | (u) | - | (u) |
| NUCLEO-F410RB | (c) | - | (c) |
| NUCLEO-F446RE | (c) | - | (c) |
| NUCLEO-F429ZI | (c) | - | (c) |
| B96B-F446VE | (c) | - | (c) |
| NUCLEO-F446ZE | (c) | - | (c) |
| DISCO-F429ZI | (u) | - | (u) |
| DISCO-F469NI | (c) | - | (c) |
Information
This library is set to use "short file name" in SDFileSystemDMA/FATFileSystem/ChaN/ffconf.h . ( _USE_LFN=0)
You can change this option to _USE_LFN=1 .
table.md@33:73237494298b, 2016-08-29 (annotated)
- Committer:
- dinau
- Date:
- Mon Aug 29 18:43:57 2016 +0900
- Revision:
- 33:73237494298b
- Parent:
- 32:49edbe5337d6
- Child:
- 36:e44163516d13
Updated: F3 boards.
Who changed what in which revision?
| User | Revision | Line number | New contents of line |
|---|---|---|---|
| dinau | 33:73237494298b | 1 | SDFileSystemDMA is enhanced SDFileSystem library for STM32 micros by using DMA functionality.\\ |
| dinau | 33:73237494298b | 2 | Max read transfer rate reaches ** over 2MByte/sec ** at 24MHz SPI clock if enough read buffer size is set.\\ |
| dinau | 33:73237494298b | 3 | Even though minimum read buffer size (512Byte) is set, read transfer rate will reach ** over 1MByte/sec ** at 24MHz SPI Clock.\\ |
| dinau | 33:73237494298b | 4 | ( but depends on the ability of each SD card)\\ |
| mimi3 | 26:fd7d88d7a4a2 | 5 | |
| mimi3 | 26:fd7d88d7a4a2 | 6 | Test program is here.\\ |
| mimi3 | 26:fd7d88d7a4a2 | 7 | [[https://developer.mbed.org/users/mimi3/code/SDFileSystemDMA-test/]]\\ |
| mimi3 | 26:fd7d88d7a4a2 | 8 | |
| dinau | 33:73237494298b | 9 | {{/media/uploads/mimi3/sdfilesystemdma-speed-test3-read-buffer-512byte.png}} |
| dinau | 33:73237494298b | 10 | |
| dinau | 33:73237494298b | 11 | {{/media/uploads/mimi3/sdfilesystemdma-speed-test-buffer-vs-spi-clock-nucleo-f411re-96mhz.png}} |
| dinau | 33:73237494298b | 12 | |
| dinau | 33:73237494298b | 13 | |
| mimi3 | 28:dfef1e7f08c9 | 14 | Supported SPI port is shown below table.\\ |
| mimi3 | 28:dfef1e7f08c9 | 15 | |
| mimi3 | 28:dfef1e7f08c9 | 16 | ** (v): Verified. It works well. ** \\ |
| dinau | 33:73237494298b | 17 | ** (w): Probably it will work well. ** (not tested) \\ |
| dinau | 33:73237494298b | 18 | ** (c): Only compiled. ** (not tested) \\ |
| mimi3 | 28:dfef1e7f08c9 | 19 | ** (f): Over flash. ** \\ |
| dinau | 33:73237494298b | 20 | ** (u) Under construction ** \\ |
| mimi3 | 28:dfef1e7f08c9 | 21 | ** (z): Dose not work. ** \\ |
| mimi3 | 26:fd7d88d7a4a2 | 22 | |
| mimi3 | 26:fd7d88d7a4a2 | 23 | Supported Boards:\\ |
| mimi3 | 26:fd7d88d7a4a2 | 24 | **Cortex-M0** |
| mimi3 | 26:fd7d88d7a4a2 | 25 | |=Board |=SPI1|=SPI2|=SPI3| |
| mimi3 | 26:fd7d88d7a4a2 | 26 | |NUCLEO-F030R8|**(v)**||| |
| mimi3 | 26:fd7d88d7a4a2 | 27 | |DISCO-F051R8 |(w) ||| |
| mimi3 | 26:fd7d88d7a4a2 | 28 | | --NUCLEO-F031K6-- |(f)||| |
| mimi3 | 26:fd7d88d7a4a2 | 29 | | --NUCLEO-F042K6-- |(f)||| |
| mimi3 | 26:fd7d88d7a4a2 | 30 | |NUCLEO-F070RB|(w)||| |
| mimi3 | 26:fd7d88d7a4a2 | 31 | |NUCLEO-F072RB|(w)||| |
| mimi3 | 26:fd7d88d7a4a2 | 32 | |NUCLEO-F091RC|(c)||| |
| dinau | 32:49edbe5337d6 | 33 | **Cortex-L0** |
| dinau | 33:73237494298b | 34 | |=Board |=SPI1|=SPI2|=SPI3| |
| mimi3 | 26:fd7d88d7a4a2 | 35 | |DISCO-L053C8 |(c)||| |
| mimi3 | 26:fd7d88d7a4a2 | 36 | |NUCLEO-L053R8|(c)||| |
| mimi3 | 28:dfef1e7f08c9 | 37 | |NUCLEO-L073RZ|(c)||| |
| mimi3 | 26:fd7d88d7a4a2 | 38 | ** Cortex-M3 ** |
| mimi3 | 26:fd7d88d7a4a2 | 39 | |=Board |=SPI1|=SPI2|=SPI3| |
| mimi3 | 28:dfef1e7f08c9 | 40 | | DISCO-F100RB |**(v)**|**(v)**|-| |
| mimi3 | 28:dfef1e7f08c9 | 41 | | NUCLEO-F103RB|**(v)**|**(v)**|-| |
| mimi3 | 28:dfef1e7f08c9 | 42 | | NUCLEO-L152RE|**(v)**|(w)|-| |
| dinau | 32:49edbe5337d6 | 43 | ** Cortex-M4 ** |
| mimi3 | 26:fd7d88d7a4a2 | 44 | ** F3 ** |
| mimi3 | 26:fd7d88d7a4a2 | 45 | |=Board |=SPI1|=SPI2|=SPI3| |
| mimi3 | 28:dfef1e7f08c9 | 46 | | DISCO-F303VC |-|**(v)**|**(v)**| |
| mimi3 | 28:dfef1e7f08c9 | 47 | | NUCLEO-F303RE|(w)|(w)|(w)| |
| dinau | 33:73237494298b | 48 | | NUCLEO-F302R8|-||(C)| |
| dinau | 33:73237494298b | 49 | | NUCLEO-F303K8|(c)|-|-| |
| dinau | 33:73237494298b | 50 | | DISCO-F334C8 |(c)|-|-| |
| dinau | 33:73237494298b | 51 | | NUCLEO-F334R8|(c)|-|-| |
| mimi3 | 26:fd7d88d7a4a2 | 52 | ** F4 ** |
| mimi3 | 26:fd7d88d7a4a2 | 53 | |=Board |=SPI1|=SPI2|=SPI3| |
| mimi3 | 28:dfef1e7f08c9 | 54 | | NUCLEO-F411RE |**(v)**|-|**(v)**| |
| mimi3 | 28:dfef1e7f08c9 | 55 | | NUCLEO-F401RE |(w)|-|(w)| |
| mimi3 | 28:dfef1e7f08c9 | 56 | | NUCLEO-F410RB |(c)|-|(c) |
| mimi3 | 28:dfef1e7f08c9 | 57 | | NUCLEO-F446RE |(c)|-|(c)| |
| dinau | 33:73237494298b | 58 | | NUCLEO-F429ZI |(c)|-|-| |
| dinau | 33:73237494298b | 59 | | NUCLEO-F446ZE |(c)|-|-| |
| dinau | 33:73237494298b | 60 | |
| dinau | 33:73237494298b | 61 | |
| mimi3 | 26:fd7d88d7a4a2 | 62 | |
| mimi3 | 26:fd7d88d7a4a2 | 63 | |
| mimi3 | 26:fd7d88d7a4a2 | 64 | |
| mimi3 | 26:fd7d88d7a4a2 | 65 | |
| mimi3 | 26:fd7d88d7a4a2 | 66 | ** Note ** \\ |
| mimi3 | 26:fd7d88d7a4a2 | 67 | This library is set to use "short file name" in SDFileSystemDMA/FATFileSystem/ChaN/ffconf.h . ( _USE_LFN=0) \\ |
| mimi3 | 26:fd7d88d7a4a2 | 68 | You can change this option to _USE_LFN=1 . |
| mimi3 | 26:fd7d88d7a4a2 | 69 | |
| mimi3 | 26:fd7d88d7a4a2 | 70 | |
| mimi3 | 26:fd7d88d7a4a2 | 71 | |
| dinau | 33:73237494298b | 72 |