Fork for adding SAM L21 Xplained Pro support

Fork of SX1276Lib by Semtech

Embed: (wiki syntax)

« Back to documentation index

SX1276MB1xAS Class Reference

#include <sx1276-hal.h>

Inherits SX1276.

Public Member Functions

virtual uint8_t DetectBoardType (void)
 Detect the board connected by reading the value of the antenna switch pin.
virtual bool CheckRfFrequency (uint32_t frequency)
 Checks if the given RF frequency is supported by the hardware.
virtual void Write (uint8_t addr, uint8_t data)
 Writes the radio register at the specified address.
virtual uint8_t Read (uint8_t addr)
 Reads the radio register at the specified address.
virtual void Write (uint8_t addr, uint8_t *buffer, uint8_t size)
 Writes multiple radio registers starting at address.
virtual void Read (uint8_t addr, uint8_t *buffer, uint8_t size)
 Reads multiple radio registers starting at address.
virtual void WriteFifo (uint8_t *buffer, uint8_t size)
 Writes the buffer contents to the SX1276 FIFO.
virtual void ReadFifo (uint8_t *buffer, uint8_t size)
 Reads the contents of the SX1276 FIFO.
virtual void Reset (void)
 Reset the SX1276.
virtual void Init (RadioEvents_t *events)
 Initializes the radio.
virtual RadioState GetStatus (void)
virtual void SetModem (RadioModems_t modem)
 Configures the SX1276 with the given modem.
virtual void SetChannel (uint32_t freq)
 Sets the channel frequency.
virtual bool IsChannelFree (RadioModems_t modem, uint32_t freq, int16_t rssiThresh)
 Sets the channels configuration.
virtual uint32_t Random (void)
 Generates a 32 bits random value based on the RSSI readings.
virtual void SetRxConfig (RadioModems_t modem, uint32_t bandwidth, uint32_t datarate, uint8_t coderate, uint32_t bandwidthAfc, uint16_t preambleLen, uint16_t symbTimeout, bool fixLen, uint8_t payloadLen, bool crcOn, bool freqHopOn, uint8_t hopPeriod, bool iqInverted, bool rxContinuous)
 Sets the reception parameters.
virtual void SetTxConfig (RadioModems_t modem, int8_t power, uint32_t fdev, uint32_t bandwidth, uint32_t datarate, uint8_t coderate, uint16_t preambleLen, bool fixLen, bool crcOn, bool freqHopOn, uint8_t hopPeriod, bool iqInverted, uint32_t timeout)
 Sets the transmission parameters.
virtual uint32_t TimeOnAir (RadioModems_t modem, uint8_t pktLen)
 Computes the packet time on air for the given payload.
virtual void Send (uint8_t *buffer, uint8_t size)
 Sends the buffer of size. Prepares the packet to be sent and sets the radio in transmission.
virtual void Sleep (void)
 Sets the radio in sleep mode.
virtual void Standby (void)
 Sets the radio in standby mode.
virtual void StartCad (void)
 Sets the radio in CAD mode.
virtual void Rx (uint32_t timeout)
 Sets the radio in reception mode for the given time.
virtual void Tx (uint32_t timeout)
 Sets the radio in transmission mode for the given time.
virtual void SetTxContinuousWave (uint32_t freq, int8_t power, uint16_t time)
 Sets the radio in continuous wave transmission mode.
virtual int16_t GetRssi (RadioModems_t modem)
 Reads the current RSSI value.
virtual void SetMaxPayloadLength (RadioModems_t modem, uint8_t max)
 Sets the maximum payload length.
virtual void SetPublicNetwork (bool enable)
 Sets the network to public or private. Updates the sync byte.

Protected Member Functions

virtual void IoInit (void)
 Initializes the radio I/Os pins interface.
virtual void RadioRegistersInit ()
 Initializes the radio registers.
virtual void SpiInit (void)
 Initializes the radio SPI.
virtual void IoIrqInit (DioIrqHandler *irqHandlers)
 Initializes DIO IRQ handlers.
virtual void IoDeInit (void)
 De-initializes the radio I/Os pins interface.
virtual void SetRfTxPower (int8_t power)
 Sets the radio output power.
virtual uint8_t GetPaSelect (uint32_t channel)
 Gets the board PA selection configuration.
virtual void SetAntSwLowPower (bool status)
 Set the RF Switch I/Os pins in Low Power mode.
virtual void AntSwInit (void)
 Initializes the RF Switch I/Os pins interface.
virtual void AntSwDeInit (void)
 De-initializes the RF Switch I/Os pins interface.
virtual void SetAntSw (uint8_t opMode)
 Controls the antena switch if necessary.
void RxChainCalibration (void)
virtual void SetOpMode (uint8_t opMode)
 Sets the SX1276 operating mode.
virtual void OnDio0Irq (void)
 DIO 0 IRQ callback.
virtual void OnDio1Irq (void)
 DIO 1 IRQ callback.
virtual void OnDio2Irq (void)
 DIO 2 IRQ callback.
virtual void OnDio3Irq (void)
 DIO 3 IRQ callback.
virtual void OnDio4Irq (void)
 DIO 4 IRQ callback.
virtual void OnDio5Irq (void)
 DIO 5 IRQ callback.
virtual void OnTimeoutIrq (void)
 Tx & Rx timeout timer callback.

Static Protected Member Functions

static uint8_t GetFskBandwidthRegValue (uint32_t bandwidth)

Protected Attributes

DigitalInOut AntSwitch
SPI spi
DigitalInOut reset
InterruptIn dio0
DioIrqHandler * dioIrq
Timeout txTimeoutTimer

Detailed Description

Actual implementation of a SX1276 radio, includes some modifications to make it compatible with the MB1 LAS board

Definition at line 47 of file sx1276-hal.h.


Member Function Documentation

void AntSwDeInit ( void   ) [protected, virtual]

De-initializes the RF Switch I/Os pins interface.

Remarks:
Needed to decrease the power consumption in MCU lowpower modes

Implements SX1276.

Definition at line 271 of file sx1276-hal.cpp.

void AntSwInit ( void   ) [protected, virtual]

Initializes the RF Switch I/Os pins interface.

Implements SX1276.

Definition at line 266 of file sx1276-hal.cpp.

bool CheckRfFrequency ( uint32_t  frequency ) [virtual]

Checks if the given RF frequency is supported by the hardware.

Parameters:
[IN]frequency RF frequency to be checked
Return values:
isSupported[true: supported, false: unsupported]

Implements SX1276.

Definition at line 294 of file sx1276-hal.cpp.

uint8_t DetectBoardType ( void   ) [virtual]

Detect the board connected by reading the value of the antenna switch pin.

Definition at line 96 of file sx1276-hal.cpp.

uint8_t GetFskBandwidthRegValue ( uint32_t  bandwidth ) [static, protected, inherited]

Returns the known FSK bandwidth registers value

Parameters:
[IN]bandwidth Bandwidth value in Hz
Return values:
regValueBandwidth register value.

Definition at line 200 of file sx1276.cpp.

uint8_t GetPaSelect ( uint32_t  channel ) [protected, virtual]

Gets the board PA selection configuration.

Parameters:
[IN]channel Channel frequency in Hz
Return values:
PaSelectRegPaConfig PaSelect value

Implements SX1276.

Definition at line 230 of file sx1276-hal.cpp.

int16_t GetRssi ( RadioModems_t  modem ) [virtual, inherited]

Reads the current RSSI value.

Return values:
rssiValueCurrent RSSI value in [dBm]

Implements Radio.

Definition at line 967 of file sx1276.cpp.

RadioState GetStatus ( void   ) [virtual, inherited]

Return current radio status

Parameters:
statusRadio status. [RF_IDLE, RX_RUNNING, TX_RUNNING]

Implements Radio.

Definition at line 82 of file sx1276.cpp.

void Init ( RadioEvents_t events ) [virtual, inherited]

Initializes the radio.

Parameters:
[IN]events Structure containing the driver callback functions

Implements Radio.

Definition at line 77 of file sx1276.cpp.

void IoDeInit ( void   ) [protected, virtual]

De-initializes the radio I/Os pins interface.

Remarks:
Useful when going in MCU lowpower modes

Implements SX1276.

Definition at line 163 of file sx1276-hal.cpp.

void IoInit ( void   ) [protected, virtual]

Initializes the radio I/Os pins interface.

Implements SX1276.

Definition at line 116 of file sx1276-hal.cpp.

void IoIrqInit ( DioIrqHandler *  irqHandlers ) [protected, virtual]

Initializes DIO IRQ handlers.

Parameters:
[IN]irqHandlers Array containing the IRQ callback functions

Implements SX1276.

Definition at line 147 of file sx1276-hal.cpp.

bool IsChannelFree ( RadioModems_t  modem,
uint32_t  freq,
int16_t  rssiThresh 
) [virtual, inherited]

Sets the channels configuration.

Parameters:
[IN]modem Radio modem to be used [0: FSK, 1: LoRa]
[IN]freq Channel RF frequency
[IN]rssiThresh RSSI threshold
Return values:
isFree[true: Channel is free, false: Channel is not free]

Implements Radio.

Definition at line 96 of file sx1276.cpp.

void OnDio0Irq ( void   ) [protected, virtual, inherited]

DIO 0 IRQ callback.

Definition at line 1151 of file sx1276.cpp.

void OnDio1Irq ( void   ) [protected, virtual, inherited]

DIO 1 IRQ callback.

Definition at line 1353 of file sx1276.cpp.

void OnDio2Irq ( void   ) [protected, virtual, inherited]

DIO 2 IRQ callback.

Definition at line 1430 of file sx1276.cpp.

void OnDio3Irq ( void   ) [protected, virtual, inherited]

DIO 3 IRQ callback.

Definition at line 1500 of file sx1276.cpp.

void OnDio4Irq ( void   ) [protected, virtual, inherited]

DIO 4 IRQ callback.

Definition at line 1531 of file sx1276.cpp.

void OnDio5Irq ( void   ) [protected, virtual, inherited]

DIO 5 IRQ callback.

Definition at line 1550 of file sx1276.cpp.

void OnTimeoutIrq ( void   ) [protected, virtual, inherited]

Tx & Rx timeout timer callback.

Definition at line 1078 of file sx1276.cpp.

void RadioRegistersInit (  ) [protected, virtual]

Initializes the radio registers.

Implements SX1276.

Definition at line 122 of file sx1276-hal.cpp.

uint32_t Random ( void   ) [virtual, inherited]

Generates a 32 bits random value based on the RSSI readings.

Remarks:
This function sets the radio in LoRa modem mode and disables all interrupts. After calling this function either Radio.SetRxConfig or Radio.SetTxConfig functions must be called.
Return values:
randomValue32 bits random value

Implements Radio.

Definition at line 119 of file sx1276.cpp.

void Read ( uint8_t  addr,
uint8_t *  buffer,
uint8_t  size 
) [virtual]

Reads multiple radio registers starting at address.

Parameters:
[IN]addr First Radio register address
[OUT]buffer Buffer where to copy the registers data
[IN]size Number of registers to be read

Implements SX1276.

Definition at line 334 of file sx1276-hal.cpp.

uint8_t Read ( uint8_t  addr ) [virtual]

Reads the radio register at the specified address.

Parameters:
[IN],:addr Register address
Return values:
dataRegister value

Implements SX1276.

Definition at line 314 of file sx1276-hal.cpp.

void ReadFifo ( uint8_t *  buffer,
uint8_t  size 
) [virtual]

Reads the contents of the SX1276 FIFO.

Parameters:
[OUT]buffer Buffer where to copy the FIFO read data.
[IN]size Number of bytes to be read from the FIFO

Implements SX1276.

Definition at line 352 of file sx1276-hal.cpp.

void Reset ( void   ) [virtual]

Reset the SX1276.

Implements SX1276.

Definition at line 300 of file sx1276-hal.cpp.

void Rx ( uint32_t  timeout ) [virtual, inherited]

Sets the radio in reception mode for the given time.

Parameters:
[IN]timeout Reception timeout [ms] [0: continuous, others timeout]

Implements Radio.

Definition at line 689 of file sx1276.cpp.

void RxChainCalibration ( void   ) [protected, inherited]

Performs the Rx chain calibration for LF and HF bands

Remarks:
Must be called just after the reset so all registers are at their default values

Definition at line 160 of file sx1276.cpp.

void Send ( uint8_t *  buffer,
uint8_t  size 
) [virtual, inherited]

Sends the buffer of size. Prepares the packet to be sent and sets the radio in transmission.

Parameters:
[IN],:buffer Buffer pointer
[IN],:size Buffer size

Implements Radio.

Definition at line 597 of file sx1276.cpp.

void SetAntSw ( uint8_t  opMode ) [protected, virtual]

Controls the antena switch if necessary.

Remarks:
see errata note
Parameters:
[IN]opMode Current radio operating mode

Implements SX1276.

Definition at line 276 of file sx1276-hal.cpp.

void SetAntSwLowPower ( bool  status ) [protected, virtual]

Set the RF Switch I/Os pins in Low Power mode.

Parameters:
[IN]status enable or disable

Implements SX1276.

Definition at line 249 of file sx1276-hal.cpp.

void SetChannel ( uint32_t  freq ) [virtual, inherited]

Sets the channel frequency.

Parameters:
[IN]freq Channel RF frequency

Implements Radio.

Definition at line 87 of file sx1276.cpp.

void SetMaxPayloadLength ( RadioModems_t  modem,
uint8_t  max 
) [virtual, inherited]

Sets the maximum payload length.

Parameters:
[IN]modem Radio modem to be used [0: FSK, 1: LoRa]
[IN]max Maximum payload length in bytes

Implements Radio.

Definition at line 1044 of file sx1276.cpp.

void SetModem ( RadioModems_t  modem ) [virtual, inherited]

Configures the SX1276 with the given modem.

Parameters:
[IN]modem Modem to be used [0: FSK, 1: LoRa]

Implements Radio.

Definition at line 1007 of file sx1276.cpp.

void SetOpMode ( uint8_t  opMode ) [protected, virtual, inherited]

Sets the SX1276 operating mode.

Parameters:
[IN]opMode New operating mode

Definition at line 993 of file sx1276.cpp.

void SetPublicNetwork ( bool  enable ) [virtual, inherited]

Sets the network to public or private. Updates the sync byte.

Remarks:
Applies to LoRa modem only
Parameters:
[IN]enable if true, it enables a public network

Implements Radio.

Definition at line 1062 of file sx1276.cpp.

void SetRfTxPower ( int8_t  power ) [protected, virtual]

Sets the radio output power.

Parameters:
[IN]power Sets the RF output power

Implements SX1276.

Definition at line 168 of file sx1276-hal.cpp.

void SetRxConfig ( RadioModems_t  modem,
uint32_t  bandwidth,
uint32_t  datarate,
uint8_t  coderate,
uint32_t  bandwidthAfc,
uint16_t  preambleLen,
uint16_t  symbTimeout,
bool  fixLen,
uint8_t  payloadLen,
bool  crcOn,
bool  freqHopOn,
uint8_t  hopPeriod,
bool  iqInverted,
bool  rxContinuous 
) [virtual, inherited]

Sets the reception parameters.

Parameters:
[IN]modem Radio modem to be used [0: FSK, 1: LoRa]
[IN]bandwidth Sets the bandwidth FSK : >= 2600 and <= 250000 Hz LoRa: [0: 125 kHz, 1: 250 kHz, 2: 500 kHz, 3: Reserved]
[IN]datarate Sets the Datarate FSK : 600..300000 bits/s LoRa: [6: 64, 7: 128, 8: 256, 9: 512, 10: 1024, 11: 2048, 12: 4096 chips]
[IN]coderate Sets the coding rate ( LoRa only ) FSK : N/A ( set to 0 ) LoRa: [1: 4/5, 2: 4/6, 3: 4/7, 4: 4/8]
[IN]bandwidthAfc Sets the AFC Bandwidth ( FSK only ) FSK : >= 2600 and <= 250000 Hz LoRa: N/A ( set to 0 )
[IN]preambleLen Sets the Preamble length ( LoRa only ) FSK : N/A ( set to 0 ) LoRa: Length in symbols ( the hardware adds 4 more symbols )
[IN]symbTimeout Sets the RxSingle timeout value FSK : timeout number of bytes LoRa: timeout in symbols
[IN]fixLen Fixed length packets [0: variable, 1: fixed]
[IN]payloadLen Sets payload length when fixed lenght is used
[IN]crcOn Enables/Disables the CRC [0: OFF, 1: ON]
[IN]freqHopOn Enables disables the intra-packet frequency hopping [0: OFF, 1: ON] (LoRa only)
[IN]hopPeriod Number of symbols bewteen each hop (LoRa only)
[IN]iqInverted Inverts IQ signals ( LoRa only ) FSK : N/A ( set to 0 ) LoRa: [0: not inverted, 1: inverted]
[IN]rxContinuous Sets the reception in continuous mode [false: single mode, true: continuous mode]

Implements Radio.

Definition at line 215 of file sx1276.cpp.

void SetTxConfig ( RadioModems_t  modem,
int8_t  power,
uint32_t  fdev,
uint32_t  bandwidth,
uint32_t  datarate,
uint8_t  coderate,
uint16_t  preambleLen,
bool  fixLen,
bool  crcOn,
bool  freqHopOn,
uint8_t  hopPeriod,
bool  iqInverted,
uint32_t  timeout 
) [virtual, inherited]

Sets the transmission parameters.

Parameters:
[IN]modem Radio modem to be used [0: FSK, 1: LoRa]
[IN]power Sets the output power [dBm]
[IN]fdev Sets the frequency deviation ( FSK only ) FSK : [Hz] LoRa: 0
[IN]bandwidth Sets the bandwidth ( LoRa only ) FSK : 0 LoRa: [0: 125 kHz, 1: 250 kHz, 2: 500 kHz, 3: Reserved]
[IN]datarate Sets the Datarate FSK : 600..300000 bits/s LoRa: [6: 64, 7: 128, 8: 256, 9: 512, 10: 1024, 11: 2048, 12: 4096 chips]
[IN]coderate Sets the coding rate ( LoRa only ) FSK : N/A ( set to 0 ) LoRa: [1: 4/5, 2: 4/6, 3: 4/7, 4: 4/8]
[IN]preambleLen Sets the preamble length
[IN]fixLen Fixed length packets [0: variable, 1: fixed]
[IN]crcOn Enables disables the CRC [0: OFF, 1: ON]
[IN]freqHopOn Enables disables the intra-packet frequency hopping [0: OFF, 1: ON] (LoRa only)
[IN]hopPeriod Number of symbols bewteen each hop (LoRa only)
[IN]iqInverted Inverts IQ signals ( LoRa only ) FSK : N/A ( set to 0 ) LoRa: [0: not inverted, 1: inverted]
[IN]timeout Transmission timeout [ms]

Implements Radio.

Definition at line 385 of file sx1276.cpp.

void SetTxContinuousWave ( uint32_t  freq,
int8_t  power,
uint16_t  time 
) [virtual, inherited]

Sets the radio in continuous wave transmission mode.

Parameters:
[IN],:freq Channel RF frequency
[IN],:power Sets the output power [dBm]
[IN],:time Transmission mode timeout [s]

Implements Radio.

Definition at line 949 of file sx1276.cpp.

void Sleep ( void   ) [virtual, inherited]

Sets the radio in sleep mode.

Implements Radio.

Definition at line 671 of file sx1276.cpp.

void SpiInit ( void   ) [protected, virtual]

Initializes the radio SPI.

Implements SX1276.

Definition at line 132 of file sx1276-hal.cpp.

void Standby ( void   ) [virtual, inherited]

Sets the radio in standby mode.

Implements Radio.

Definition at line 680 of file sx1276.cpp.

void StartCad ( void   ) [virtual, inherited]

Sets the radio in CAD mode.

Implements Radio.

Definition at line 916 of file sx1276.cpp.

uint32_t TimeOnAir ( RadioModems_t  modem,
uint8_t  pktLen 
) [virtual, inherited]

Computes the packet time on air for the given payload.

Can only be called once SetRxConfig or SetTxConfig have been called

Parameters:
[IN]modem Radio modem to be used [0: FSK, 1: LoRa]
[IN]pktLen Packet payload length
Return values:
airTimeComputed airTime for the given packet payload length

Implements Radio.

Definition at line 518 of file sx1276.cpp.

void Tx ( uint32_t  timeout ) [virtual, inherited]

Sets the radio in transmission mode for the given time.

Parameters:
[IN]timeout Transmission timeout [ms] [0: continuous, others timeout]

Implements Radio.

Definition at line 854 of file sx1276.cpp.

void Write ( uint8_t  addr,
uint8_t *  buffer,
uint8_t  size 
) [virtual]

Writes multiple radio registers starting at address.

Parameters:
[IN]addr First Radio register address
[IN]buffer Buffer containing the new register's values
[IN]size Number of registers to be written

Implements SX1276.

Definition at line 321 of file sx1276-hal.cpp.

void Write ( uint8_t  addr,
uint8_t  data 
) [virtual]

Writes the radio register at the specified address.

Parameters:
[IN],:addr Register address
[IN],:data New register value

Implements SX1276.

Definition at line 309 of file sx1276-hal.cpp.

void WriteFifo ( uint8_t *  buffer,
uint8_t  size 
) [virtual]

Writes the buffer contents to the SX1276 FIFO.

Parameters:
[IN]buffer Buffer containing data to be put on the FIFO.
[IN]size Number of bytes to be written to the FIFO

Implements SX1276.

Definition at line 347 of file sx1276-hal.cpp.


Field Documentation

DigitalInOut AntSwitch [protected]

Antenna switch GPIO pins objects

Definition at line 53 of file sx1276-hal.h.

InterruptIn dio0 [protected, inherited]

SX1276 DIO pins

Definition at line 75 of file sx1276.h.

DioIrqHandler* dioIrq [protected, inherited]

Hardware DIO IRQ functions

Definition at line 91 of file sx1276.h.

DigitalInOut reset [protected, inherited]

SX1276 Reset pin

Definition at line 70 of file sx1276.h.

SPI spi [protected, inherited]

SPI Interface

Definition at line 64 of file sx1276.h.

Timeout txTimeoutTimer [protected, inherited]

Tx and Rx timers

Definition at line 96 of file sx1276.h.