File content as of revision 2:d0778c36d28d:

//
#include "DigiPot.h"
#include "MCP4651.h"

Serial dbg1(USBTX,USBRX);

// Enable pins for PCA9
BusOut Pbus(p14,p13,p12,p11);

//Serial dbg(USBTX, USBRX);

MCP4651 Chip1(p9, p10, 0x1);
MCP4651 Chip2(p9, p10, 0x2);
MCP4651 Chip3(p9, p10, 0x3);
MCP4651 Chip4(p9, p10, 0x5);
MCP4651 Chip5(p9, p10, 0x6);
MCP4651 Chip6(p9, p10, 0x7);


//  The MCP4651 go to mid scale on reset
//  Use the general call commands to set all pots to zero
//  Set the lowest values pot to approximately 10k
 
int PotReset(void) {
    char wip0[2] = {0x80, 0x0};
    char wip1[2] = {0x90, 0x0};    
    I2C GenCall(p9,p10);
    
    // Reset R1 & R2
    Pbus = 0x1;
    GenCall.write(0x0, wip0, 2);
    GenCall.write(0x0, wip1, 2);
    Chip1.SetValue(0,50); // About 10k on 50k pot
    Chip4.SetValue(0,50);
    
    // Reset R3 & R4
    Pbus = 0x2;
    GenCall.write(0x0, wip0, 2);
    GenCall.write(0x0, wip1, 2);
    Chip1.SetValue(0,50);
    Chip4.SetValue(0,50);
    
    // Reset R5 & R6
    Pbus = 0x4;
    GenCall.write(0x0, wip0, 2);
    GenCall.write(0x0, wip1, 2);
    Chip1.SetValue(0,50);
    Chip4.SetValue(0,50);
    
    // Pbus = 0x8; /* Not Used at this time */
    Pbus = 0;
    return(0);
} // End PotReset

//  Decode the HID report and set the pots
int SetResist( uint8_t *data) {
    int wiper = 0, value = 0;
    dbg1.printf("data[0] = %d\n",data[0]);
    dbg1.printf("data[1] = %d\n",data[1]);
    dbg1.printf("data[2] = %d\n",data[2]);
    dbg1.printf("data[3] = %d\n",data[3]);
    dbg1.printf("data[4] = %d\n",data[4]);
    dbg1.printf("data[5] = %d\n",data[5]);
    if (data[0] != 3) return(1);
    if (data[1] == 0) return(1); // Zero = bus disable
    if (data[3] == 0) return(1); // Zero disallowed
    Pbus = data[1];
    if(data[4] > 0) wiper = (data[4] - 1);
    value = data[5];
    
    switch (data[3]) {
        case 1:
            Chip1.SetValue(wiper, value);
            dbg1.printf("Set Pbus = %d, Chip = %d, Pot = %d, Value = %d\n", data[1], data[3], wiper, value);
            break;
        case 2:
            Chip2.SetValue(wiper, value);
            dbg1.printf("Set Pbus = %d, Chip = %d, Pot = %d, Value = %d\n", data[1], data[3], wiper, value);
            break;
        case 3:
            Chip3.SetValue(wiper, value);
            dbg1.printf("Set Pbus = %d, Chip = %d, Pot = %d, Value = %d\n", data[1], data[3], wiper, value);
            break;
        case 4:
            Chip4.SetValue(wiper, value);
            dbg1.printf("Set Pbus = %d, Chip = %d, Pot = %d, Value = %d\n", data[1], data[3], wiper, value);
            break;
        case 5:
            Chip5.SetValue(wiper, value);
            dbg1.printf("Set Pbus = %d, Chip = %d, Pot = %d, Value = %d\n", data[1], data[3], wiper, value);
            break;
        case 6:
            Chip6.SetValue(wiper, value);
            dbg1.printf("Set Pbus = %d, Chip = %d, Pot = %d, Value = %d\n", data[1], data[3], wiper, value);
            break;
        default:
            break;
       }
    dbg1.printf("Resistor Set Done\n");
    data[0] = 0;
    Pbus = 0;
    return(0);
} // End SetResist