hadif azli
/
TEST123
BLYNK TEST
Diff: main.cpp
- Revision:
- 3:4cd9171ba989
- Parent:
- 2:6cd3b0947188
- Child:
- 5:8a3cf73d7ed3
diff -r 6cd3b0947188 -r 4cd9171ba989 main.cpp --- a/main.cpp Wed Jun 15 03:08:40 2016 +0000 +++ b/main.cpp Thu Jun 16 08:08:30 2016 +0000 @@ -1,30 +1,37 @@ #include "mbed.h" +#include "Config.h" #include "MicroduinoPinNames.h" DigitalOut myled(P0_20); I2C g_i2c(P0_11, P0_10);//SDA, SCL -#if 1 #include "SimpleTimer.h" #include "userDef.h" #include "sensor.h" +#ifdef OPEN_OLED #include "oled.h" #endif -//#include "WiFiBlynk.h" +#include "WiFiBlynk.h" -//Serial pc(P0_4, P0_0); // tx, rx - +Serial pc(P0_4, P0_0); // tx, rx Timer g_Timer; +Ticker g_Ticker; void led_flash() { static int count = 0; count++; //pc.printf("count : %d, ms : %d\r\n", count, g_Timer.read_ms()); - //myled = 1; + myled = 1; wait_ms(70); myled = 0; } +static void led_flash_fast() +{ + myled = !myled; +} + +#ifdef OPEN_OLED Adafruit_SSD1306_I2c adaf(g_i2c, P0_13, 0x78, 64, 128); void update_oled() { @@ -33,46 +40,56 @@ myled = 0; oled(adaf, sensor_tem, sensor_hum, sensor_light, sensorPM25, Sensor_etoh); } +#endif int main() { - //pc.baud(9600); + g_Ticker.attach_us(led_flash_fast, 30000); + pc.baud(115200); + pc.printf("Enter main()\r\n"); //myled = 1; g_Timer.start(); SimpleTimer gSimpleTimer(g_Timer); - - //Serial.begin(9600); // See the connection status in Serial Monitor - // Set ESP8266 baud rate - //EspSerial.begin(115200); + + /* + * Set ESP8266 baud rate + * 在LPC824上,波特率设为115200时,ESP8266是无法工作 + */ + EspSerial.baud(9600); - //Blynk.begin(auth, wifi, SSID, PASS); - + Blynk.begin(auth, wifi, SSID, PASS); + wait(5.0); + g_Ticker.detach(); + // Setup a function to be called every second - //gSimpleTimer.setInterval(2000L, senTempHumi); + gSimpleTimer.setInterval(2000L, senTempHumi); gSimpleTimer.setInterval(1000, updateLight); gSimpleTimer.setInterval(5000, updateCH4); gSimpleTimer.setInterval(4000, updateTempHumi); //gSimpleTimer.setInterval(3000, PM25); - //gSimpleTimer.setInterval(4000, led_flash); + gSimpleTimer.setInterval(4000, led_flash); +#ifdef OPEN_OLED gSimpleTimer.setInterval(1000, update_oled); - +#endif //PM25_init(); wait_ms(2000); +#ifdef OPEN_OLED oled_init(adaf); +#endif int pretime = g_Timer.read_ms(); while(1) { //pc.printf("Enter while(1)\r\n"); //myled = !myled; - //Blynk.run(); // All the Blynk Magic happens here... + Blynk.run(); // All the Blynk Magic happens here... gSimpleTimer.run(); - #if 0 +#if 0 int curtime = g_Timer.read_ms(); if (curtime - pretime > 4000) { //updateTempHumi(); led_flash(); pretime = curtime; } - #endif - +#endif + } }