Jurica Resetar
acd52832 blinky example
Revision 0:796985b808bc, committed 2016-09-15
- Comitter:
- jurica238814
- Date:
- Thu Sep 15 11:57:29 2016 +0000
- Child:
- 1:8fd903e4bcef
- Commit message:
- BSP file done.
Changed in this revision
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/acd52832_bsp.h Thu Sep 15 11:57:29 2016 +0000
@@ -0,0 +1,76 @@
+/* Copyright (c) 2016 Aconno. All Rights Reserved.
+ *
+ * Licensees are granted free, non-transferable use of the information. NO
+ * WARRANTY of ANY KIND is provided. This heading must NOT be removed from
+ * the file.
+ *
+ */
+
+/**
+ * General IO pins
+ */
+ #define PIN_BUTTON (p25) //S1 gpio number (Active low)
+ #define PIN_LED (p26) //LD1 gpio number (Active low)
+ #define PIN_IRLED (p27) //LD4 gpio number (Active high)
+ #define PIN_BUZZER (p31) //LS1 gpio number (Active high)
+
+ #define PIN_LED_RED (p22) //Module red LED
+ #define PIN_LED_BLUE (p23) //Module blue LED
+ #define PIN_LED_GREEN (p24) //Module green LED
+
+/**
+ * Alternate General IO pins
+ * Connect:
+ * (+, c, -) (Orange, Red, Brown)
+ */
+ #define PIN_SERVO1 (p25) //Servo1 gpio number
+ #define PIN_SERVO2 (p26) //Servo2 gpio number
+
+/**
+ * Analog to Digital Conversion (ADC) pins
+ */
+ #define ADC_BAT (p2) //Battery
+ #define ADC_POT (p28) //Potentiometer
+ #define ADC_LIGHT (p29) //Light Dependant Resistor
+ #define ADC_TEMP (p30) //Temperature Dependant Resistor
+
+/**
+ * Electronic Paper Display (EPD) pins
+ */
+ #define PIN_EPD_CS (p5) //EPD Chip select pin (Active low)
+ #define PIN_EPD_DC (p6) //EPD Data/Command pin (Data active high)
+ #define PIN_EPD_RST (p7) //EPD Reset pin (Active low)
+ #define PIN_EPD_BUSY (p8) //EPD Busy pin (Active low)
+ #define PIN_EPD_SCK (p4) //EPD SCK pin
+ #define PIN_EPD_MOSI (p3) //EPD MOSI pin
+ #define PIN_EPD_MISO (0xFF) //EPD MISO pin not used
+
+/**
+ * IO Expander pins
+ */
+ #define PIN_EXP_RST (p19) //IO Expander reset pin
+ #define PIN_EXP_INT_A (p11) //IO Expander interrupt for PORTA
+ #define PIN_EXP_INT_B (p12) //IO Expander interrupt for PORTB
+ #define PIN_EXP_SDA (p20) //TWI SCK pin
+ #define PIN_EXP_SCL (p21) //TWI SCL pin
+
+/**
+ * Pins concerning TWI Addresses
+ * Control bits are added by nrf_drv_twi
+*/
+ #define TWI_EXPANDER_ADDR (0x20) //Port expander address
+ #define TWI_AG_ADDR (0x6A) //Accelerometer/Gyroscope address
+ #define TWI_MAG_ADDR (0x1C) //Magnetometer address
+
+ /**
+ * Define structure used by bluetooth library
+ * Define if BLE_LIB is defined as preprocessor symbol
+ */
+#ifdef BLE_LIB
+ // Low frequency clock source to be used by the SoftDevice
+ #define NRF_CLOCK_LFCLKSRC { \
+ .source = NRF_CLOCK_LF_SRC_XTAL, \
+ .rc_ctiv = 0, \
+ .rc_temp_ctiv = 0, \
+ .xtal_accuracy = NRF_CLOCK_LF_XTAL_ACCURACY_20_PPM}
+#endif
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/main.cpp Thu Sep 15 11:57:29 2016 +0000
@@ -0,0 +1,25 @@
+/* Copyright (c) 2016 Aconno. All Rights Reserved.
+ *
+ * Licensees are granted free, non-transferable use of the information. NO
+ * WARRANTY of ANY KIND is provided. This heading must NOT be removed from
+ * the file.
+ *
+ * aconno simple example program
+ * blinky LED LD1
+ */
+
+#include "mbed.h"
+#include "acd52832_bsp.h"
+
+#define pause 1 // Pause in seconds
+
+DigitalOut LD1(PIN_LED);
+
+int main(){
+ while(1){
+ LD1 = 1;
+ wait(pause);
+ LD1 = 0;
+ wait(pause);
+ }
+}
\ No newline at end of file
--- /dev/null Thu Jan 01 00:00:00 1970 +0000 +++ b/mbed.bld Thu Sep 15 11:57:29 2016 +0000 @@ -0,0 +1,1 @@ +http://mbed.org/users/mbed_official/code/mbed/builds/2e9cc70d1897 \ No newline at end of file