mbed library sources

Fork of mbed-src by mbed official



File content as of revision 563:9f26fcd0c9ce:

/* mbed Microcontroller Library
 * Copyright (c) 2006-2013 ARM Limited
 * Licensed under the Apache License, Version 2.0 (the "License");
 * you may not use this file except in compliance with the License.
 * You may obtain a copy of the License at
 *     http://www.apache.org/licenses/LICENSE-2.0
 * Unless required by applicable law or agreed to in writing, software
 * distributed under the License is distributed on an "AS IS" BASIS,
 * See the License for the specific language governing permissions and
 * limitations under the License.
#ifndef MBED_SPI_API_H
#define MBED_SPI_API_H

#include "device.h"
#include "dma_api.h"
#include "buffer.h"


#define SPI_EVENT_ERROR       (1 << 1)
#define SPI_EVENT_COMPLETE    (1 << 2)
#define SPI_EVENT_RX_OVERFLOW (1 << 3)

#define SPI_EVENT_INTERNAL_TRANSFER_COMPLETE (1 << 30) // internal flag to report an event occurred

#define SPI_FILL_WORD         (0xFFFF)

/** Asynch spi hal structure
typedef struct {
    struct spi_s spi;        /**< Target specific spi structure */
    struct buffer_s tx_buff; /**< Tx buffer */
    struct buffer_s rx_buff; /**< Rx buffer */
} spi_t;

/** Non-asynch spi hal structure
typedef struct spi_s spi_t;


#ifdef __cplusplus
extern "C" {

 * \defgroup GeneralSPI SPI Configuration Functions
 * @{

/** Initialize the SPI peripheral
 * Configures the pins used by SPI, sets a default format and frequency, and enables the peripheral
 * @param[out] obj  The SPI object to initialize
 * @param[in]  mosi The pin to use for MOSI
 * @param[in]  miso The pin to use for MISO
 * @param[in]  sclk The pin to use for SCLK
 * @param[in]  ssel The pin to use for SSEL
void spi_init(spi_t *obj, PinName mosi, PinName miso, PinName sclk, PinName ssel);

/** Release a SPI object
 * TODO: spi_free is currently unimplemented
 * This will require reference counting at the C++ level to be safe
 * Return the pins owned by the SPI object to their reset state
 * Disable the SPI peripheral
 * Disable the SPI clock
 * @param[in] obj The SPI object to deinitialize
void spi_free(spi_t *obj);

/** Configure the SPI format
 * Set the number of bits per frame, configure clock polarity and phase, shift order and master/slave mode
 * @param[in,out] obj   The SPI object to configure
 * @param[in]     bits  The number of bits per frame
 * @param[in]     mode  The SPI mode (clock polarity, phase, and shift direction)
 * @param[in]     slave Zero for master mode or non-zero for slave mode
void spi_format(spi_t *obj, int bits, int mode, int slave);

/** Set the SPI baud rate
 * Actual frequency may differ from the desired frequency due to available dividers and bus clock
 * Configures the SPI peripheral's baud rate
 * @param[in,out] obj The SPI object to configure
 * @param[in]     hz  The baud rate in Hz
void spi_frequency(spi_t *obj, int hz);

 * \defgroup SynchSPI Synchronous SPI Hardware Abstraction Layer
 * @{

/** Write a byte out in master mode and receive a value
 * @param[in] obj   The SPI peripheral to use for sending
 * @param[in] value The value to send
 * @return Returns the value received during send
int  spi_master_write(spi_t *obj, int value);

/** Check if a value is available to read
 * @param[in] obj The SPI peripheral to check
 * @return non-zero if a value is available
int  spi_slave_receive(spi_t *obj);

/** Get a received value out of the SPI receive buffer in slave mode
 * Blocks until a value is available
 * @param[in] obj The SPI peripheral to read
 * @return The value received
int  spi_slave_read(spi_t *obj);

/** Write a value to the SPI peripheral in slave mode
 * Blocks until the SPI peripheral can be written to
 * @param[in] obj   The SPI peripheral to write
 * @param[in] value The value to write
void spi_slave_write(spi_t *obj, int value);

/** Checks if the specified SPI peripheral is in use
 * @param[in] obj The SPI peripheral to check
 * @return non-zero if the peripheral is currently transmitting
int  spi_busy(spi_t *obj);

/** Get the module number
 * @param[in] obj The SPI peripheral to check
 * @return The module number
uint8_t spi_get_module(spi_t *obj);


 * \defgroup AsynchSPI Asynchronous SPI Hardware Abstraction Layer
 * @{

/** Begin the SPI transfer. Buffer pointers and lengths are specified in tx_buff and rx_buff
 * @param[in] obj       The SPI object which holds the transfer information
 * @param[in] tx        The buffer to send
 * @param[in] tx_length The number of words to transmit
 * @param[in] rx        The buffer to receive
 * @param[in] rx_length The number of words to receive
 * @param[in] bit_width The bit width of buffer words
 * @param[in] event     The logical OR of events to be registered
 * @param[in] handler   SPI interrupt handler
 * @param[in] hint      A suggestion for how to use DMA with this transfer
void spi_master_transfer(spi_t *obj, void *tx, size_t tx_length, void *rx, size_t rx_length, uint8_t bit_width, uint32_t handler, uint32_t event, DMAUsage hint);

/** The asynchronous IRQ handler
 * Reads the received values out of the RX FIFO, writes values into the TX FIFO and checks for transfer termination
 * conditions, such as buffer overflows or transfer complete.
 * @param[in] obj     The SPI object which holds the transfer information
 * @return event flags if a transfer termination condition was met or 0 otherwise.
uint32_t spi_irq_handler_asynch(spi_t *obj);

/** Attempts to determine if the SPI peripheral is already in use.
 * If a temporary DMA channel has been allocated, peripheral is in use.
 * If a permanent DMA channel has been allocated, check if the DMA channel is in use.  If not, proceed as though no DMA
 * channel were allocated.
 * If no DMA channel is allocated, check whether tx and rx buffers have been assigned.  For each assigned buffer, check
 * if the corresponding buffer position is less than the buffer length.  If buffers do not indicate activity, check if
 * there are any bytes in the FIFOs.
 * @param[in] obj The SPI object to check for activity
 * @return non-zero if the SPI port is active or zero if it is not.
uint8_t spi_active(spi_t *obj);

/** Abort an SPI transfer
 * @param obj The SPI peripheral to stop
void spi_abort_asynch(spi_t *obj);



#ifdef __cplusplus
#endif // __cplusplus

#endif // SPI_DEVICE

#endif // MBED_SPI_API_H