123
Fork of LG by
Diff: commandset.c
- Revision:
- 129:406995a91322
- Parent:
- 112:4a96133a1311
diff -r 1e4675a36c93 -r 406995a91322 commandset.c --- a/commandset.c Mon Apr 11 11:04:34 2016 +0000 +++ b/commandset.c Tue Apr 12 11:10:49 2016 +0000 @@ -372,18 +372,18 @@ void M_Gph_W(void) //e.------------ set the gain factor of photodetector channels ------------------- //r.------------ установка усиления каналов фотоприемника ------------------- { - Device_blk.Str.Gain_Ph_A = rcv_buf[4]; //e. read from the receiver buffer the value of the gain factor of the A channel //r. считать из буфера приемника значение усиления канала А + /* Device_blk.Str.Gain_Ph_A = rcv_buf[4]; //e. read from the receiver buffer the value of the gain factor of the A channel //r. считать из буфера приемника значение усиления канала А Device_blk.Str.Gain_Ph_B = rcv_buf[5]; //e. read from the receiver buffer the value of the gain factor of the B channel //r. считать из буфера приемника значение усиления канала В Out_G_photo(Device_blk.Str.Gain_Ph_A, Device_blk.Str.Gain_Ph_B); //e. display these values to digital potentiometers //r. вывести эти значения в цифровые потенциометры trm_cycl = 0; //e. periodic data transmission is not needed //r. периодическая передача ответа не требуется - Mk_Ask1(); + Mk_Ask1();*/ } // M_Gph_W -/* + void M_Rate(void) //e.------------ start of transfer of the M_Rate parameters stack ------------------- //r.------------ запуск передачи набора параметров M_Rate ------------------- { - uint8_t mode; + /* uint8_t mode; SetSpeedPeriod(); //e. set the answer transfer rate and its periodicity //r. установить скорость передачи ответа и его периодичность UART_SwitchSpeed(trm_rate); @@ -500,25 +500,25 @@ trm_ena = 1; //e. allow operation of the transmitter //r. разрешить работу передатчика break; } - SetIntLatch(wrk_period); + SetIntLatch(wrk_period);*/ } // M_Rate -*/ + void M_Reset(void) { while(1); } // will not achieve void M_Param_R(void) //e. ------------ read the parameter of the GLD from the data memory ---------------------- //r.------------ чтение параметра GLD из памяти данных ---------------------- -{ +{/* num_of_par = 1; //e. 1 parameter output //r. выводить один параметр addr_param[0] = (void *)(&Device_blk.Str.My_Addres + rcv_buf[3]); //e. address of the needed parameter in the block //r. адрес требуемого параметра в блоке size_param[0] = 2; //e. size of the buffer - 2 bytes //r. размер буфера - 2 байта - trm_ena = 1; //e. allow operation of the transmitter //r. разрешить работу передатчика + trm_ena = 1; */ //e. allow operation of the transmitter //r. разрешить работу передатчика*/ } // M_Param_R void M_Param_W(void) //e.------------ write the parameter of the GLD from the data memory ----------------------- //r.------------ запись параметра GLD в память данных ----------------------- -{ +{/* int * ptr; ScopeMode = 0; //e. VB_DELAY_MEANDER allocate a mode of display for a control point of an scope //r. VB_DELAY_MEANDER назначить режим отображения для контрольной точки осциллографа @@ -528,22 +528,22 @@ *ptr = (rcv_buf[4] << 8) | (rcv_buf[5] & 0xFF); // write new parameter value trm_cycl = 0; //e. periodic data transmission is not needed //r. периодическая передача ответа не требуется - Mk_Ask1(); + Mk_Ask1();*/ } // M_Param_W void M_LdPar_F() //e.============ procedure for load the GLD parameters from the flash-memory =========== //r.============ процедура загрузки параметров ГЛД из флэш-памяти =========== { - +/* LoadFlashParam(FromFLASH); //e. load the GLD parameters from the flash-memory //r. загрузить параметры ГЛД из фдэш-памяти blt_in_test = ((uint32_t)FIRMWARE_VER << 8) | (Device_blk.Str.Device_SerialNumber & 0x00FF); // Init_software(); trm_cycl = 0; //e. periodic data transmission is not needed //r. периодическая передача ответа не требуется - Mk_Ask1(); + Mk_Ask1();*/ } // M_LdPar_F void M_LdPar_D(void) //e.============ procedure for set parameters of the GLD by default ============ //r.============ процедура установки параметров ГЛД по умолчанию ============ -{ +{/* #if !defined COMMAND_DEBUG LoadFlashParam(ByDefault); //e. define parameters of the GLD by default //r. определить параметры ГЛД по умолчанию (default) Init_software(); @@ -582,7 +582,7 @@ } // B_Delta void D_Period_W(void) //e. === set the period of the angle increase output //r. === установка периода выдачи приращения угла -{ +{*/ } // D_Period_W // ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++