File content as of revision 1:d8eaa5aa6ad5:

/*********************************************************************
*          Portions COPYRIGHT 2015 STMicroelectronics                *
*          Portions SEGGER Microcontroller GmbH & Co. KG             *
*        Solutions for real time microcontroller applications        *
**********************************************************************
*                                                                    *
*        (c) 1996 - 2015  SEGGER Microcontroller GmbH & Co. KG       *
*                                                                    *
*        Internet: www.segger.com    Support:  support@segger.com    *
*                                                                    *
**********************************************************************

** emWin V5.28 - Graphical user interface for embedded applications **
All  Intellectual Property rights  in the Software belongs to  SEGGER.
emWin is protected by  international copyright laws.  Knowledge of the
source code may not be used to write a similar product.  This file may
only be used in accordance with the following terms:

The  software has  been licensed  to STMicroelectronics International
N.V. a Dutch company with a Swiss branch and its headquarters in Plan-
les-Ouates, Geneva, 39 Chemin du Champ des Filles, Switzerland for the
purposes of creating libraries for ARM Cortex-M-based 32-bit microcon_
troller products commercialized by Licensee only, sublicensed and dis_
tributed under the terms and conditions of the End User License Agree_
ment supplied by STMicroelectronics International N.V.
Full source code is available at: www.segger.com

We appreciate your understanding and fairness.
----------------------------------------------------------------------
File        : GUI_X.C
Purpose     : Config / System dependent externals for GUI
---------------------------END-OF-HEADER------------------------------
*/

/**
  ******************************************************************************
  * @attention
  *
  * Licensed under MCD-ST Liberty SW License Agreement V2, (the "License");
  * You may not use this file except in compliance with the License.
  * You may obtain a copy of the License at:
  *
  *        http://www.st.com/software_license_agreement_liberty_v2
  *
  * Unless required by applicable law or agreed to in writing, software 
  * distributed under the License is distributed on an "AS IS" BASIS, 
  * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
  * See the License for the specific language governing permissions and
  * limitations under the License.
  *
  ******************************************************************************
  */

#include "GUI.h"

/*********************************************************************
*
*       Global data
*/
volatile GUI_TIMER_TIME OS_TimeMS;

/*********************************************************************
*
*      Timing:
*                 GUI_X_GetTime()
*                 GUI_X_Delay(int)

  Some timing dependent routines require a GetTime
  and delay function. Default time unit (tick), normally is
  1 ms.
*/

GUI_TIMER_TIME GUI_X_GetTime(void) { 
  return OS_TimeMS; 
}

void GUI_X_Delay(int ms) { 
  int tEnd = OS_TimeMS + ms;
  while ((tEnd - OS_TimeMS) > 0);
}

/*********************************************************************
*
*       GUI_X_Init()
*
* Note:
*     GUI_X_Init() is called from GUI_Init is a possibility to init
*     some hardware which needs to be up and running before the GUI.
*     If not required, leave this routine blank.
*/

void GUI_X_Init(void) {}


/*********************************************************************
*
*       GUI_X_ExecIdle
*
* Note:
*  Called if WM is in idle state
*/

void GUI_X_ExecIdle(void) {}

/*********************************************************************
*
*      Logging: OS dependent

Note:
  Logging is used in higher debug levels only. The typical target
  build does not use logging and does therefor not require any of
  the logging routines below. For a release build without logging
  the routines below may be eliminated to save some space.
  (If the linker is not function aware and eliminates unreferenced
  functions automatically)

*/

void GUI_X_Log     (const char *s) { GUI_USE_PARA(s); }
void GUI_X_Warn    (const char *s) { GUI_USE_PARA(s); }
void GUI_X_ErrorOut(const char *s) { GUI_USE_PARA(s); }

/*************************** End of file ****************************/