These are the examples provided for [[/users/frank26080115/libraries/LPC1700CMSIS_Lib/]] Note, the entire "program" is not compilable!
Diff: EMAC/EmacRaw/abstract.h
- Revision:
- 0:bf7b9fba3924
diff -r 000000000000 -r bf7b9fba3924 EMAC/EmacRaw/abstract.h --- /dev/null Thu Jan 01 00:00:00 1970 +0000 +++ b/EMAC/EmacRaw/abstract.h Sun Mar 20 05:38:56 2011 +0000 @@ -0,0 +1,122 @@ + ******************** (C) COPYRIGHT 2010 NXPSemiconductors ******************* + * @file EMAC\EmacRaw\abstract.txt + * @author NXP MCU SW Application Team + * @version 2.0 + * @date + * @brief Description of the EMAC EmacRaw example. + ****************************************************************************** + * Software that is described herein is for illustrative purposes only + * which provides customers with programming information regarding the + * products. This software is supplied "AS IS" without any warranties. + * NXP Semiconductors assumes no responsibility or liability for the + * use of the software, conveys no license or title under any patent, + * copyright, or mask work right to the product. NXP Semiconductors + * reserves the right to make changes in the software without + * notification. NXP Semiconductors also make no representation or + * warranty that such application will be suitable for the specified + * use without further testing or modification. + ****************************************************************************** + +@Example description: + Purpose: + This example describes how to test EMAC driver with raw packet frame format + that is not related with any upper-layer (i.e. TCP/IP...). + Process: + There are two ways to test: + - TX_ONLY and BOUNCE_RX flags can be set one at a time, not both. + When TX_ONLY is set to 1, it's a TX_ONLY packet from the MCB1700 + board to the LAN. Use the traffic analyzer such as ethereal, once + the program is running, the packets can be monitored on the traffic + analyzer. + - When BOUNCE_RX is set to 1 (TX_ONLY needs to reset to 0), it's a + test to test both TX and RX, use the traffic generator/analyzer, + you can creat a packet with the destination address as that on the + MCB1700 board, use the traffic generator to send packets, as long + as the destination address matches, MCB1700 will reverse the source + and destination address and send the packets back on the network. + ENABLE_WOL flag is used to test power down and WOL functionality. + BOUNCE_RX flag needs to be set to 1 when WOL is being tested. + +@Directory contents: + \EWARM: includes EWARM (IAR) project and configuration files + \Keil: includes RVMDK (Keil)project and configuration files + + crc32c.h/.c: Ethernet CRC module + emactest.c: main program + libnosys_gnu.c: Definitions for OS interface, stub function required by newlibc + used by Codesourcery GNU compiler. + lpc17xx_libcfg.h: Library configuration file - include needed driver library for this example + makefile: Example's makefile (to build with GNU toolchain) + +@How to run: + Hardware configuration: + This example is tested on: + Keil MCB1700 vers.1 + These jumpers must be configured as following: + - VDDIO: ON + - VDDREGS: ON + - VBUS: ON + - LED: ON + - E/C: 2-3 (Ethernet) + - E/U: 2-3 (Ethernet) + - Remain jumpers: OFF + IAR LPC1768 vers.A + These jumpers must be configured as following: + - PWR_SEL: depending of power source + - DBG_EN : ON + - ACC_IRQ/LED2: 2-3 (LED2) + - Remain jumpers: OFF + + Serial display configuration: (e.g: TeraTerm, Hyperterminal, Flash Magic...) + 115200bps + 8 data bit + No parity + 1 stop bit + No flow control + + Running mode: + This example can run only on RAM/ROM mode. + + Note: If want to burn hex file to board by using Flash Magic, these jumpers need + to be connected: + - MCB1700 with LPC1768 ver.1: + + RST: ON + + ISP: ON + - IAR LPC1768 KickStart vers.A: + + RST_E: ON + + ISP_E: ON + + (Please reference "LPC1000 Software Development Toolchain" - chapter 4 "Creating and working with + LPC1000CMSIS project" for more information) + + Step to run: + - Step 1: Choose correct working board by uncomment correct defined board in lpc17xx_emac.h file + + If using MCB1700 board, uncomment "#define MCB_LPC_1768" + + If using IAR-LPC1768-KS board, uncomment "#define MCB_LPC_1768" + (Should not uncomment both symbols at the same time) + - Step 2: setting flag (in emactest.c): + - TX_ONLY = 1 + - BOUNCE_RX = 0 + Build example and burn into first board. + - Step 3: setting flag: + - TX_ONLY = 0 + - BOUNCE_RX = 1 + Build example and burn into second board. + - Step 4: Use CrossOver cable to connect two boards. + - Step 5: Connect UART0 on two boards to COM ports on your computer. + - Step 6: Configure hardware and serial display as above instruction. + - Step 7: Hit reset button on two boards. + - Step 8: Wait for EMAC initilization completes on two board. + - Step 9: If ENABLE_WOL is enabled on board 'BOUNCE_RX' side, after initializing EMAC, + it will enter sleep mode to be waked-up on LAN (WoL). + - Step 10: On 'TX_ONLY' side, hit INT0 button to send a frame. + - Step 11: After receiving frame, 'BOUNCE_RX' side will be waked-up and operates + properly. + + (Pls reference "LPC17xx Example Description" document - chapter "Examples > EMAC > EmacRaw" + for more details) +@Tip: + - Open \EWARM\*.eww project file to run example on IAR + - Open \RVMDK\*.uvproj project file to run example on Keil + + \ No newline at end of file