Elijah Orr
Fork of the official mbed C/C SDK provides the software platform and libraries to build your applications for RenBED.
Dependents: 1-RenBuggyTimed RenBED_RGB RenBED_RGB_PWM RenBED_RGB
Fork of
mbed
by 
mbed official
Diff: TARGET_NUCLEO_F411RE/stm32f4xx_hal_pwr.h
- Revision:
- 110:165afa46840b
- Parent:
- 106:ba1f97679dad
diff -r 9296ab0bfc11 -r 165afa46840b TARGET_NUCLEO_F411RE/stm32f4xx_hal_pwr.h
--- a/TARGET_NUCLEO_F411RE/stm32f4xx_hal_pwr.h Thu Oct 29 08:40:18 2015 +0000
+++ b/TARGET_NUCLEO_F411RE/stm32f4xx_hal_pwr.h Wed Nov 25 13:21:40 2015 +0000
@@ -2,8 +2,8 @@
******************************************************************************
* @file stm32f4xx_hal_pwr.h
* @author MCD Application Team
- * @version V1.3.2
- * @date 26-June-2015
+ * @version V1.4.1
+ * @date 09-October-2015
* @brief Header file of PWR HAL module.
******************************************************************************
* @attention
@@ -85,7 +85,6 @@
* @{
*/
#define PWR_WAKEUP_PIN1 ((uint32_t)0x00000100)
-#define PWR_WAKEUP_PIN2 ((uint32_t)0x00000080)
/**
* @}
*/
@@ -169,43 +168,6 @@
* @{
*/
-#if defined(STM32F405xx) || defined(STM32F407xx) || defined(STM32F415xx) || defined(STM32F417xx)
-/** @brief macros configure the main internal regulator output voltage.
- * @param __REGULATOR__: specifies the regulator output voltage to achieve
- * a tradeoff between performance and power consumption when the device does
- * not operate at the maximum frequency (refer to the datasheets for more details).
- * This parameter can be one of the following values:
- * @arg PWR_REGULATOR_VOLTAGE_SCALE1: Regulator voltage output Scale 1 mode
- * @arg PWR_REGULATOR_VOLTAGE_SCALE2: Regulator voltage output Scale 2 mode
- * @retval None
- */
-#define __HAL_PWR_VOLTAGESCALING_CONFIG(__REGULATOR__) do { \
- __IO uint32_t tmpreg; \
- MODIFY_REG(PWR->CR, PWR_CR_VOS, (__REGULATOR__)); \
- /* Delay after an RCC peripheral clock enabling */ \
- tmpreg = READ_BIT(PWR->CR, PWR_CR_VOS); \
- UNUSED(tmpreg); \
- } while(0)
-#else
-/** @brief macros configure the main internal regulator output voltage.
- * @param __REGULATOR__: specifies the regulator output voltage to achieve
- * a tradeoff between performance and power consumption when the device does
- * not operate at the maximum frequency (refer to the datasheets for more details).
- * This parameter can be one of the following values:
- * @arg PWR_REGULATOR_VOLTAGE_SCALE1: Regulator voltage output Scale 1 mode
- * @arg PWR_REGULATOR_VOLTAGE_SCALE2: Regulator voltage output Scale 2 mode
- * @arg PWR_REGULATOR_VOLTAGE_SCALE3: Regulator voltage output Scale 3 mode
- * @retval None
- */
-#define __HAL_PWR_VOLTAGESCALING_CONFIG(__REGULATOR__) do { \
- __IO uint32_t tmpreg; \
- MODIFY_REG(PWR->CR, PWR_CR_VOS, (__REGULATOR__)); \
- /* Delay after an RCC peripheral clock enabling */ \
- tmpreg = READ_BIT(PWR->CR, PWR_CR_VOS); \
- UNUSED(tmpreg); \
- } while(0)
-#endif /* STM32F405xx || STM32F407xx || STM32F415xx || STM32F417xx */
-
/** @brief Check PWR flag is set or not.
* @param __FLAG__: specifies the flag to check.
* This parameter can be one of the following values:
@@ -445,7 +407,6 @@
/** @defgroup PWR_IS_PWR_Definitions PWR Private macros to check input parameters
* @{
*/
-#define IS_PWR_WAKEUP_PIN(PIN) (((PIN) == PWR_WAKEUP_PIN1) || ((PIN) == PWR_WAKEUP_PIN2))
#define IS_PWR_PVD_LEVEL(LEVEL) (((LEVEL) == PWR_PVDLEVEL_0) || ((LEVEL) == PWR_PVDLEVEL_1)|| \
((LEVEL) == PWR_PVDLEVEL_2) || ((LEVEL) == PWR_PVDLEVEL_3)|| \
((LEVEL) == PWR_PVDLEVEL_4) || ((LEVEL) == PWR_PVDLEVEL_5)|| \