wayne roberts
Hardware Abstraction Layer, permitting any LoRa application to use any LoRa radio chip
Dependents: alarm_slave alarm_master lora_p2p lorawan1v1 ... more
radio chip selection
Radio chip driver is not included, allowing choice of radio device.
If you're using SX1272 or SX1276, then import sx127x driver into your program.
if you're using SX1261 or SX1262, then import sx126x driver into your program.
if you're using SX1280, then import sx1280 driver into your program.
if you're using LR1110, then import LR1110 driver into your program.
If you're using NAmote72 or Murata discovery, then you must import only sx127x driver.
If you're using Type1SJ select target DISCO_L072CZ_LRWAN1 and import sx126x driver into your program.
Pin assigned to arduino LoRa radio shield form-factor
- SX1272 shield.
- SX1276 shield.
- SX126x kit with color touch screen, or sx126x radio-only shield.
- Exceptions with their own pin assignments: NAMote-72 and Murata discovery board.
- TODO: pin assign XDOT.
Diff: radio_ff_arduino_sx127x.cpp
- Revision:
- 0:9c052ff8dd6a
- Child:
- 5:ab124d3842a8
diff -r 000000000000 -r 9c052ff8dd6a radio_ff_arduino_sx127x.cpp
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/radio_ff_arduino_sx127x.cpp Thu Jul 05 17:31:54 2018 -0700
@@ -0,0 +1,105 @@
+/* Only for NUCLEO boards: prevent compiling for MOTE_L152RC and typeABZ discovery */
+#if defined(TARGET_FF_ARDUINO) && defined(TARGET_FF_MORPHO) && !defined(TARGET_DISCO_L072CZ_LRWAN1)
+#include "radio.h"
+#ifdef SX127x_H
+#include "SPIu.h"
+
+SPIu spi(D11, D12, D13); // mosi, miso, sclk
+// dio0, dio1, nss, spi, rst
+SX127x Radio::radio( D2, D3, D10, spi, A0); // sx127[62] arduino shield
+SX127x_lora Radio::lora(radio);
+SX127x_fsk Radio::fsk(radio);
+
+InterruptIn Radio::dio0(D2);
+InterruptIn Radio::dio1(D3);
+
+typedef enum {
+ SHIELD_TYPE_NONE = 0,
+ SHIELD_TYPE_LAS,
+ SHIELD_TYPE_MAS,
+} shield_type_e;
+shield_type_e shield_type;
+
+#ifdef TARGET_FF_MORPHO
+DigitalOut pc3(PC_3); // debug RX indication, for nucleo boards
+#endif /* TARGET_FF_MORPHO */
+DigitalInOut rfsw(A4);
+void Radio::rfsw_callback()
+{
+ if (radio.RegOpMode.bits.Mode == RF_OPMODE_TRANSMITTER)
+ rfsw = 1;
+ else
+ rfsw = 0;
+
+ if (radio.RegOpMode.bits.Mode == RF_OPMODE_RECEIVER || radio.RegOpMode.bits.Mode == RF_OPMODE_RECEIVER_SINGLE)
+ pc3 = 1;
+ else
+ pc3 = 0;
+}
+
+void
+Radio::set_tx_dbm(int8_t dbm)
+{
+ RegPdsTrim1_t pds_trim;
+ uint8_t adr;
+
+ if (radio.type == SX1276)
+ adr = REG_PDSTRIM1_SX1276;
+ else
+ adr = REG_PDSTRIM1_SX1272;
+
+ pds_trim.octet = radio.read_reg(adr);
+
+ if (shield_type == SHIELD_TYPE_LAS)
+ radio.RegPaConfig.bits.PaSelect = 1;
+ else
+ radio.RegPaConfig.bits.PaSelect = 0;
+
+ if (radio.RegPaConfig.bits.PaSelect) {
+ /* PABOOST used: +2dbm to +17, or +20 */
+ if (dbm > 17) {
+ if (dbm > 20)
+ dbm = 20;
+ dbm -= 3;
+ pds_trim.bits.prog_txdac = 7;
+ radio.write_reg(adr, pds_trim.octet);
+ ocp(150);
+ } else
+ ocp(120);
+
+ if (dbm > 1)
+ radio.RegPaConfig.bits.OutputPower = dbm - 2;
+ } else {
+ /* RFO used: -1 to +14dbm */
+ ocp(80);
+ if (dbm < 15)
+ radio.RegPaConfig.bits.OutputPower = dbm + 1;
+ }
+ radio.write_reg(REG_PACONFIG, radio.RegPaConfig.octet);
+
+ radio.RegPaConfig.octet = radio.read_reg(REG_PACONFIG);
+ if (radio.RegPaConfig.bits.PaSelect) {
+ dbm = radio.RegPaConfig.bits.OutputPower + pds_trim.bits.prog_txdac - 2;
+ } else {
+ dbm = radio.RegPaConfig.bits.OutputPower - 1;
+ }
+}
+
+void Radio::boardInit()
+{
+ printf("boardInit sx127x-ff-arduino ");
+ rfsw.input();
+ if (rfsw.read()) {
+ shield_type = SHIELD_TYPE_LAS;
+ printf("LAS\r\n");
+ } else {
+ shield_type = SHIELD_TYPE_MAS;
+ printf("MAS\r\n");
+ }
+
+ rfsw.output();
+}
+
+#endif /* ..SX127x_H */
+#endif /* ...sx127x shield */
+