Hardware Abstraction Layer, permitting any LoRa application to use any LoRa radio chip
Dependents: alarm_slave alarm_master lora_p2p lorawan1v1 ... more
radio chip selection
Radio chip driver is not included, allowing choice of radio device.
If you're using SX1272 or SX1276, then import sx127x driver into your program.
if you're using SX1261 or SX1262, then import sx126x driver into your program.
if you're using SX1280, then import sx1280 driver into your program.
if you're using LR1110, then import LR1110 driver into your program.
If you're using NAmote72 or Murata discovery, then you must import only sx127x driver.
If you're using Type1SJ select target DISCO_L072CZ_LRWAN1
and import sx126x driver into your program.
Pin assigned to arduino LoRa radio shield form-factor
- SX1272 shield.
- SX1276 shield.
- SX126x kit with color touch screen, or sx126x radio-only shield.
- Exceptions with their own pin assignments: NAMote-72 and Murata discovery board.
- TODO: pin assign XDOT.
TARGET_DISCO_L072CZ_LRWAN1/radio_typeABZ.cpp
- Committer:
- Wayne Roberts
- Date:
- 2020-06-12
- Revision:
- 18:78c5e644d37a
- Parent:
- 5:ab124d3842a8
File content as of revision 18:78c5e644d37a:
#include "radio.h" #ifdef SX127x_H #define SSA_BOARD 1 #include "SPIu.h" SPIu spi(PA_7, PA_6, PB_3); // mosi, miso, sclk // dio0, dio1, nss, spi, rst SX127x Radio::radio(PB_4, PB_1, PA_15, spi, PC_0); // sx1276 arduino shield SX127x_lora Radio::lora(radio); SX127x_fsk Radio::fsk(radio); InterruptIn Radio::dio0(PB_4); InterruptIn Radio::dio1(PB_1); #define CRF1 PA_1 #define CRF2 PC_2 #define CRF3 PC_1 DigitalOut Vctl1(CRF1); DigitalOut Vctl2(CRF2); DigitalOut Vctl3(CRF3); void Radio::rfsw_callback() { if (radio.RegOpMode.bits.Mode == RF_OPMODE_TRANSMITTER) { Vctl1 = 0; if (radio.RegPaConfig.bits.PaSelect) { Vctl2 = 0; Vctl3 = 1; } else { Vctl2 = 1; Vctl3 = 0; } } else { if (radio.RegOpMode.bits.Mode == RF_OPMODE_RECEIVER || radio.RegOpMode.bits.Mode == RF_OPMODE_RECEIVER_SINGLE) Vctl1 = 1; else Vctl1 = 0; Vctl2 = 0; Vctl3 = 0; } } void Radio::set_tx_dbm(int8_t dbm) { RegPdsTrim1_t pds_trim; unsigned v = radio.read_reg(REG_PATEST_SX1276); if (dbm == PA_OFF_DBM) { /* for bench testing: prevent overloading receiving station (very low TX power) */ v &= ~0x20; // turn off pu_regpa_n: disable PA radio.write_reg(REG_PATEST_SX1276, v); return; } else if ((v & 0x20) == 0) { v |= 0x20; // turn on pu_regpa_n: enable PA radio.write_reg(REG_PATEST_SX1276, v); } pds_trim.octet = radio.read_reg(REG_PDSTRIM1_SX1276); if (dbm > 13) { radio.RegPaConfig.bits.PaSelect = 1; if (dbm > 17) { pds_trim.bits.prog_txdac = 7; dbm -= 3; ocp(150); } else { pds_trim.bits.prog_txdac = 4; ocp(120); } radio.RegPaConfig.bits.OutputPower = dbm - 2; } else { pds_trim.bits.prog_txdac = 4; radio.RegPaConfig.bits.PaSelect = 0; radio.RegPaConfig.bits.OutputPower = dbm + 1; ocp(80); } radio.write_reg(REG_PACONFIG, radio.RegPaConfig.octet); radio.write_reg(REG_PDSTRIM1_SX1276, pds_trim.octet); } #ifdef SSA_BOARD DigitalOut pa12(PA_12); // tcxo enable DigitalOut pa11(PA_11); // sw9v enable -> sw3v3 #endif void Radio::boardInit() { #ifdef SSA_BOARD pa12 = 1; // tcxo pa11 = 1; // sw9v -> sw3v3 #endif } #endif /* ..SX127x_H */