end node on synchronous star LoRa network.

Dependencies:   SX127x sx12xx_hal TSL2561

radio chip selection

Radio chip driver is not included, allowing choice of radio device.
If you're using SX1272 or SX1276, then import sx127x driver into your program.
if you're using SX1261 or SX1262, then import sx126x driver into your program.
if you're using SX1280, then import sx1280 driver into your program.
If you're using NAmote72 or Murata discovery, then you must import only sx127x driver.

This project for use with LoRaWAN_singlechannel_gateway project.

Alternately gateway running on raspberry pi can be used as gateway.

LoRaWAN on single radio channel

Network description is at gateway project page. Synchronous star network.

Hardware Support

This project supports SX1276 and SX1272, sx126x kit, sx126x shield, and sx128x 2.4GHz. The ST board B-L072Z-LRWAN1 is also supported (TypeABZ module). When B-L072Z-LRWAN1 target is selected, TARGET_DISCO_L072CZ_LRWAN1 is defined by tools, allowing correct radio driver configuration for this platform. Alternately, any mbed board that can use LoRa radio shield board should work, but NUCLEO boards are tested.

End-node Unique ID

DevEUI is created from CPU serial number. AppEUI and AppKey are declared as software constants.

End-node Configuration

Data rate definition LORAMAC_DEFAULT_DATARATE configured in LoRaMac-definitions.h. See gateway project page for configuration of gateway.
LoRaWAN addressing is configured in Comissioning.h; only OTA mode is functional.
Header file board/lora_config.h, selects application layer options (i.e. sensors) to be compiled in.

Serial Interface

Serial port operates at 115200bps.
Application layer single_us915_main.cpp User button triggers uplink (i.e. blue button on nucleo board), or jumper enables continuously sends repeated uplink packets. The MAC layer holds each uplink request until the allocated timeslot.

commandargumentsdescription
?-print available commands
. (period)-print status (DevEUI, DevAddr, etc)
ullength integerset payload length of test uplink packets

sensor demo

Selected grove sensors may be plugged into SX1272 shield.
To enable, edit lora_config.h to define SENSORS.

Sensor connections on SX1272MB2xAS:

D8 D9: buttonRX TX: (unused)A3 A4: Rotary Angle Sensor
D6 D7: RGB LEDSCL SDA: digital light sensorA1 A2: Rotary Angle Sensor

Digital input pin, state reported via uplink: PC8
Digital output pin, controlled via downlink: PC6
PWM out: PB_10

Jumper enables auto-repeated transmit: PC10 and PC12 on NUCLEO board, located on end of morpho headers nearby JP4.

Revision:
0:8f0d0ae0a077
--- /dev/null	Thu Jan 01 00:00:00 1970 +0000
+++ b/system/utilities.h	Thu May 18 15:11:53 2017 -0700
@@ -0,0 +1,99 @@
+/*
+ / _____)             _              | |
+( (____  _____ ____ _| |_ _____  ____| |__
+ \____ \| ___ |    (_   _) ___ |/ ___)  _ \
+ _____) ) ____| | | || |_| ____( (___| | | |
+(______/|_____)_|_|_| \__)_____)\____)_| |_|
+    (C)2013 Semtech
+
+Description: Helper functions implementation
+
+License: Revised BSD License, see LICENSE.TXT file include in the project
+
+Maintainer: Miguel Luis and Gregory Cristian
+*/
+#ifndef __UTILITIES_H__
+#define __UTILITIES_H__
+
+/*!
+ * \brief Returns the minimum value betwen a and b
+ *
+ * \param [IN] a 1st value
+ * \param [IN] b 2nd value
+ * \retval minValue Minimum value
+ */
+#define MIN( a, b ) ( ( ( a ) < ( b ) ) ? ( a ) : ( b ) )
+
+/*!
+ * \brief Returns the maximum value betwen a and b
+ *
+ * \param [IN] a 1st value
+ * \param [IN] b 2nd value
+ * \retval maxValue Maximum value
+ */
+#define MAX( a, b ) ( ( ( a ) > ( b ) ) ? ( a ) : ( b ) )
+
+/*!
+ * \brief Returns 2 raised to the power of n
+ *
+ * \param [IN] n power value
+ * \retval result of raising 2 to the power n
+ */
+#define POW2( n ) ( 1 << n )
+
+/*!
+ * \brief Initializes the pseudo ramdom generator initial value
+ *
+ * \param [IN] seed Pseudo ramdom generator initial value
+ */
+void srand1( uint32_t seed );
+
+/*!
+ * \brief Computes a random number between min and max
+ *
+ * \param [IN] min range minimum value
+ * \param [IN] max range maximum value
+ * \retval random random value in range min..max
+ */
+int32_t randr( int32_t min, int32_t max );
+
+/*!
+ * \brief Copies size elements of src array to dst array
+ * 
+ * \remark STM32 Standard memcpy function only works on pointers that are aligned
+ *
+ * \param [OUT] dst  Destination array
+ * \param [IN]  src  Source array
+ * \param [IN]  size Number of bytes to be copied
+ */
+void memcpy1( uint8_t *dst, const uint8_t *src, uint16_t size );
+
+/*!
+ * \brief Copies size elements of src array to dst array reversing the byte order
+ *
+ * \param [OUT] dst  Destination array
+ * \param [IN]  src  Source array
+ * \param [IN]  size Number of bytes to be copied
+ */
+void memcpyr( uint8_t *dst, const uint8_t *src, uint16_t size );
+
+/*!
+ * \brief Set size elements of dst array with value 
+ * 
+ * \remark STM32 Standard memset function only works on pointers that are aligned
+ *
+ * \param [OUT] dst   Destination array
+ * \param [IN]  value Default value
+ * \param [IN]  size  Number of bytes to be copied
+ */
+void memset1( uint8_t *dst, uint8_t value, uint16_t size );
+
+/*!
+ * \brief Converts a nibble to an hexadecimal character
+ * 
+ * \param [IN] a   Nibble to be converted
+ * \retval hexChar Converted hexadecimal character
+ */
+int8_t Nibble2HexChar( uint8_t a );
+
+#endif // __UTILITIES_H__