Users » dreschpe » Code » FT800_2

Lib for FTDI FT800 graphic controller "EVE" The API is changed from the FTDI original names. It use smaller names now. DL() will add something to the display list instead of Ft_App_WrCoCmd_Buffer ... The FTDI programmer Guide is also using this commands.

Dependents: FT800_RGB_demo FT800_RGB_demo2 FT800_demo_for_habr Temp_&_RH_at_TFT-demo ... more

Fork of FT800 by Peter Drescher

The mbed is talking thru the SPI interface with the graphic engine. We have to set up a list of Commands and send them to the FT800 to get graphics.

Hardware

1. VM800C development modules from FTDI : http://www.ftdichip.com/Products/Modules/VM800C.html

The modules come with different size lcd. 3.5", 4.3" or 5" or without. /media/uploads/dreschpe/ftdi_eve.jpg The picture shows a modified board, because my lcd had a different pinout. The mbed is connected to the pin header on the bottom.

2. EVBEVE-FT800 board from GLYN: http://www.glyn.com/News-Events/Newsletter/Newsletter-2013/October-2013/A-quick-start-for-EVE-Requires-no-basic-knowledge-graphics-sound-and-touch-can-all-be-learned-in-minutes

The module has a 40 pin flex cable connector to connect a display out of the EDT series.

/media/uploads/dreschpe/glyn_eve.jpg

The mbed is connected via the pin header on the left. If you use this board with a EDT display you have to uncomment the #define Inv_Backlite in FT_LCD_Type.h, because the backlight dimming is inverted.

3. ConnectEVE board from MikroElektronika http://www.mikroe.com/add-on-boards/display/connecteve/#headers_10 The board has also a pin header to connect the mbed. - not tested, but it looks like the other boards.

4. ADAM arduino shield http://www.4dsystems.com.au/product/4DLCD_FT843/ Component page : http://mbed.org/components/ADAM/

Works with the NUCLEO boards, but you have to patch three wires.

/media/uploads/dreschpe/adam.jpg

Connection

We need 5 signals to connect to the mbed. SCK, MOSI and MISO are connected to a SPI channel. SS is the chip select signal and PD work as powerdown. The additional INT signal is not used at the moment. It is possible to generate a interrupt signal, but at the moment you have to poll the status register of the FT800 to see if a command is finished.

Software

This lib is based on the demo code from FTDI. If you want to use it, you have to read the programming manual : http://www.ftdichip.com/Support/Documents/ProgramGuides/FT800%20Programmers%20Guide.pdf

See my demo : http://mbed.org/users/dreschpe/code/FT800_RGB_demo/

FT_LCD_Type.h

Committer:: dreschpe
Date:: 2014-01-04
Revision:: 2:ab74a9a05970
Parent:: 0:5e013296b353
Child:: 3:392d2c733c68

File content as of revision 2:ab74a9a05970:

/* mbed Library for FTDI FT800  Enbedded Video Engine "EVE"
 * ported to mbed by Peter Drescher, DC2PD 2014
 * Released under the MIT License: http://mbed.org/license/mit */
 
 /* change this file to adapt other LCD screens */
 
#ifndef FT_LCD_TYPE_H
#define FT_LCD_TYPE_H

/* Global variables for display resolution to support various display panels */
/* Default is WQVGA - 480x272 */

#define my_DispWidth  480
#define my_DispHeight 272
#define my_DispHCycle 548
#define my_DispHOffset 43
#define my_DispHSync0  0
#define my_DispHSync1  41
#define my_DispVCycle  292
#define my_DispVOffset  12
#define my_DispVSync0  0
#define my_DispVSync1  10
#define my_DispPCLK  5
#define my_DispSwizzle  0
#define my_DispPCLKPol  1

/* the GLYN display has inverted backlite */
#define Inv_Backlite    

#endif