This program is guided to help establish a connection between two RFM95 900MHz LoRa radio modules using Maxim Integrated's Feather MCUs (MAX32630FTHR Mbed and the MAX32620FTHR Mbed). Once the radios are configured after powering on and if the radios are wired correctly, the two radios will self identify as either a master or a slave, and will then proceed to PING and PONG back and forth. Information about what is happening between the radios can be seen if the two boards are hooked up to a USB COM port through the included DAPLINK/MAX32625PICO modules.

Dependencies:   BufferedSerial SX1276GenericLib USBDeviceHT max32630fthr

Fork of MAX326xxFTHR_LoRa_PingPong by Devin Alexander

Fri Jun 15 18:23:44 2018 +0000
testing committing again to see if it re-generates the page again

Who changed what in which revision?

UserRevisionLine numberNew contents of line
Helmut64 0:c43b6919ae15 1 /*
Helmut64 17:98f2528e8399 2 * Copyright (c) 2018 HELIOS Software GmbH
Helmut64 0:c43b6919ae15 3 * 30826 Garbsen (Hannover) Germany
Helmut64 0:c43b6919ae15 4 * Licensed under the Apache License, Version 2.0);
dev_alexander 21:458f85f54121 5 */
Helmut64 0:c43b6919ae15 6 #include "main.h"
Helmut64 0:c43b6919ae15 7
dev_alexander 19:9f035b9e65ec 8 #if defined(TARGET_MAX32630FTHR) // using the RFM95 board
dev_alexander 19:9f035b9e65ec 9 #include "max32630fthr.h"
dev_alexander 19:9f035b9e65ec 10 MAX32630FTHR pegasus(MAX32630FTHR::VIO_3V3);
dev_alexander 19:9f035b9e65ec 11 #endif
Helmut64 0:c43b6919ae15 12
Helmut64 17:98f2528e8399 13 DigitalOut myled(LED);
Helmut64 0:c43b6919ae15 14
Helmut64 0:c43b6919ae15 15
Helmut64 17:98f2528e8399 16 int main() {
Helmut64 17:98f2528e8399 17 #ifdef HELTEC_STM32L4
Helmut64 17:98f2528e8399 18 DigitalOut vext(POWER_VEXT);
Helmut64 17:98f2528e8399 19 vext = POWER_VEXT_ON;
Helmut64 17:98f2528e8399 20 #endif
dev_alexander 19:9f035b9e65ec 21
dev_alexander 19:9f035b9e65ec 22
Helmut64 17:98f2528e8399 23 /*
Helmut64 17:98f2528e8399 24 * inits the Serial or USBSerial when available (230400 baud).
Helmut64 17:98f2528e8399 25 * If the serial uart is not is not connected it swiches to USB Serial
Helmut64 17:98f2528e8399 26 * blinking LED means USBSerial detected, waiting for a connect.
Helmut64 17:98f2528e8399 27 * It waits up to 30 seconds for a USB terminal connections
Helmut64 17:98f2528e8399 28 */
Helmut64 17:98f2528e8399 29 InitSerial(30*1000, &myled);
Helmut64 17:98f2528e8399 30 dprintf("Welcome to the SX1276GenericLib");
Helmut64 18:d5527ce82e6b 31
Helmut64 17:98f2528e8399 32 dprintf("Starting a simple LoRa PingPong");
Helmut64 17:98f2528e8399 33 SX1276PingPong();
Helmut64 0:c43b6919ae15 34 }