Andrew Klimenyuk
STM32F103C8T6_WIFI_Heating_system
Dependencies: mbed mbed-STM32F103C8T6 eeprom_flash Watchdog PinDetect DS1820
- Bluepill STM32F103C8T6 Heating system
- _This project is core part of bigger heating system project!_
Features
- Reading temperature from four DS18B20 sensors
- Making a decision about switching on/off heater and pomp
- Executing simple user commands from UART
- Storing state parameters to program memory (EEPROM emulation)
Diff: temp_controller/temp_controller.cpp
- Revision:
- 45:abc682827659
- Parent:
- 42:03cbc2a6f63b
- Child:
- 46:0d60fbcfb245
diff -r e6efa8be1f9e -r abc682827659 temp_controller/temp_controller.cpp
--- a/temp_controller/temp_controller.cpp Sat Sep 22 17:33:14 2018 +0000
+++ b/temp_controller/temp_controller.cpp Sun Sep 23 15:04:46 2018 +0000
@@ -117,6 +117,7 @@
void process_temp() {
+
switch(working_mode) {
case 0:
// 0 - OFF - heating off, pomp and heater are OFF
@@ -125,6 +126,9 @@
break;
case 1:
// 1 - ECO - eco heating
+
+ set_pomp_and_heater_by(temp);
+
//pc.printf("State %d|%d|%d|%d|%d\r\n", temp_error[0], temp_error[1], temp_error[2], temp_error[3], temp_error[4] );
//pc.printf("Temp %3.1f|%3.1f|%3.1f|%3.1f|%3.1f\r\n", temp[0], temp[1], temp[2], temp[3], temp[4] );
//pc.printf("RAM_config=%X, FLASH_config=%X\r\n", eeprom_config_value ,readEEPROMWord(0));
@@ -133,14 +137,15 @@
heater_OFF = !heater_OFF;
break;
case 2:
+
+ set_pomp_and_heater_by(temp);
// 2 - STANDART - standart heating
pomp_OFF = 1;
heater_OFF = 1;
break;
case 3:
// 3 - SIMULATOR - simulator mode - work on simulated_temp
- pomp_OFF = 1;
- heater_OFF = 1;
+ set_pomp_and_heater_by(simulated_temp);
break;
case 4:
// 4 - POMP - pomp is ON, heater is OFF
@@ -181,4 +186,97 @@
v = ( v << 8 ) | MAX_HOT_WATER_TEMP;
};
return v;
-};
\ No newline at end of file
+};
+
+void set_pomp_and_heater_by(float * work_temp) {
+ // temp config array = outdoor|litos|mebel|hot_water|back_water
+
+ /*
+ eeprom_config_value:
+ 1 unsigned char - Min mebel temp (default +15)
+ 2 unsigned char Min litos temp (default +10)
+ 3 unsigned char Min back water temp (default +10)
+ 4 unsigned char Max hot water temp (default +35)
+ */
+ unsigned char min_mebel_temp = eeprom_config_value >> 24;
+ unsigned char min_litos_temp = ( 0x00FF0000 & eeprom_config_value) >> 16;
+ unsigned char min_back_water_temp = ( 0x0000FF00 & eeprom_config_value) >> 8;
+ unsigned char max_hot_water_temp = 0x000000FF & eeprom_config_value;
+
+ //__disable_irq();
+ //pc.printf("Level %d|%d|%d|%d\r\n", min_mebel_temp, min_litos_temp, min_back_water_temp, max_hot_water_temp);
+ //__enable_irq();
+
+ float outdoor = *(work_temp);
+ float litos = *(work_temp + 1);
+ float mebel = *(work_temp + 2);
+ float hot_water = *(work_temp + 3);
+ float back_water = *(work_temp + 4);
+
+ if (outdoor > litos) {
+ // ============================================= SUMMER MODE
+ // system off
+ pomp_OFF = 1;
+ heater_OFF = 1;
+
+ } else if ( outdoor < 3) {
+ // ============================================== WINTER MODE
+ // pomp is always on
+ pomp_OFF = 0;
+
+ if (mebel < min_mebel_temp ||
+ litos < min_litos_temp ||
+ back_water < min_back_water_temp) {
+ // when if somewhere is colder than it must be
+ if (hot_water > max_hot_water_temp) {
+ heater_OFF = 1;
+ } else {
+ if ( heater_OFF == 1 ) {
+ if (hot_water < (max_hot_water_temp - 10)) {
+ heater_OFF = 0;
+ } else {
+ heater_OFF = 1;
+ };
+ } else {
+ heater_OFF = 0;
+ };
+ };
+ } else {
+ heater_OFF = 1;
+ };
+
+ } else {
+ // ======================================== DEMI SEASON MODE
+
+ if (mebel < min_mebel_temp ||
+ litos < min_litos_temp ||
+ back_water < min_back_water_temp) {
+ // when if somewhere is colder than it must be
+ pomp_OFF = 0;
+ if ( hot_water > (max_hot_water_temp-10) ) {
+ heater_OFF = 1;
+ } else {
+ if ( heater_OFF == 1 ) {
+ if ( hot_water < (min_back_water_temp + 2) ) {
+ heater_OFF = 0;
+ } else {
+ heater_OFF = 1;
+ };
+ } else {
+ heater_OFF = 0;
+ };
+ };
+ } else {
+ heater_OFF = 1;
+ if ( hot_water > min_back_water_temp ) {
+ pomp_OFF = 0;
+ } else {
+ pomp_OFF = 1;
+ };
+ };
+ };
+
+ //__disable_irq();
+ //pc.printf("Temp %3.1f|%3.1f|%3.1f|%3.1f|%3.1f\r\n", *(work_temp), *(work_temp + 1), *(work_temp + 2), *(work_temp + 3), *(work_temp + 4) );
+ //__enable_irq();
+};
\ No newline at end of file