Diff: mbed-dev/targets/TARGET_NXP/TARGET_LPC43XX/README.txt

Revision:

10:41552d038a69

--- /dev/null	Thu Jan 01 00:00:00 1970 +0000
+++ b/mbed-dev/targets/TARGET_NXP/TARGET_LPC43XX/README.txt	Tue Jan 10 20:42:26 2017 +0000
@@ -0,0 +1,81 @@
+mbed port to NXP LPC43xx
+========================
+Updated: 07/11/14
+
+The NXP LPC43xx microcontrollers includes multiple Cortex-M cores in a single
+microcontroller package. This port allows mbed developers to take advantage
+of the LPC43xx in their application using APIs that they are familiar with.
+Some of the key features of the LPC43xx include:
+
+* Dual core ARM Cortex-M4/M0 both capable of up to 204 MHz
+* Up to 264 KB SRAM, 1 MB internal flash
+* Two High-speed USB 2.0 interfaces
+* Ethernet MAC
+* LCD interface
+* Quad-SPI Flash Interface (SPIFI)
+* State Configurable Timer (SCT)
+* Serial GPIO (SGPIO)
+* Up to 164 GPIO
+
+The NXP LPC18xx is a single core Cortex-M3 implementation that is compatible
+with the LPC43XX for cost-sensitive applications not requiring multiple cores.
+
+mbed port to the LPC43XX - Micromint USA <support@micromint.com>
+
+Compatibility
+-------------
+* This port has been tested with the following boards:
+    Board                    MCU        RAM/Flash
+    Micromint Bambino 200    LPC4330    264K SRAM/4 MB SPIFI flash
+    Micromint Bambino 200E   LPC4330    264K SRAM/8 MB SPIFI flash
+    Micromint Bambino 210    LPC4330    264K SRAM/4 MB SPIFI flash
+    Micromint Bambino 210E   LPC4330    264K SRAM/8 MB SPIFI flash
+
+* CMSIS-DAP debugging is implemented with the Micromint Bambino 210/210E.
+  To debug other LPC4330 targets, use a JTAG. The NXP DFU tool can be used
+  for flash programming.
+
+* This port should support NXP LPC43XX and LPC18XX variants with a single
+  codebase. The core declaration specifies the binaries to be built:
+    mbed define      CMSIS define  MCU Target
+    __CORTEX_M4      CORE_M4       LPC43xx Cortex-M4
+    __CORTEX_M0      CORE_M0       LPC43xx Cortex-M0
+    __CORTEX_M3      CORE_M3       LPC18xx Cortex-M3
+  These MCUs all share the peripheral IP, common driver code is feasible.
+  Yet each variant can have different memory segments, peripherals, etc.
+  Plus, each board design can integrate different external peripherals
+  or interfaces. A future release of the mbed SDK and its build tools will
+  support specifying the target board when building binaries. At this time
+  building binaries for different targets requires an external project or
+  Makefile.
+
+* No testing has been done with LPC18xx hardware.
+
+Notes
+-----
+* On the LPC43xx the hardware pin name and the GPIO pin name are not the same,
+  requiring different offsets for the SCU and GPIO registers. To simplify logic
+  the pin identifier encodes the offsets. Macros are used for decoding.
+  For example, P6_11 corresponds to GPIO3[7] and is encoded/decoded as follows:
+
+    P6_11 = MBED_PIN(0x06, 11, 3, 7) = 0x032C0067
+
+    MBED_SCU_REG(P6_11)  = 0x4008632C      MBED_GPIO_PORT(P6_11) = 3
+    MBED_GPIO_REG(P6_11) = 0x400F4000      MBED_GPIO_PIN(P6_11)  = 7
+
+* Pin names use multiple aliases to support Arduino naming conventions as well
+  as others. For example, to use pin p21 on the Bambino 210 from mbed applications
+  the following aliases are equivalent: p21, D0, UART0_TX, COM1_TX, P6_4.
+  See the board pinout graphic and the PinNames.h for available aliases.
+
+* The LPC43xx implements GPIO pin and group interrupts. Any pin in the 8 32-bit
+  GPIO ports can interrupt (LPC4350 supports up to 164). On group interrupts a
+  pin can only interrupt on the rising or falling edge, not both as required
+  by the mbed InterruptIn class. Also, group interrupts can't be cleared
+  individually. This implementation uses pin interrupts (8 on M4/M3, 1 on M0).
+  A future implementation may provide group interrupt support.
+
+* The LPC3xx PWM driver uses the State Configurable Timer (SCT). The default
+  build (PWM_MODE=0) uses the unified 32-bit times. Applications that use PWM
+  and require other SCT uses can use the dual 16-bit mode by changing PWM_MODE
+  when building the library.