Revision 0:fa750b405a24, committed 2019-06-05

Comitter:

TMRL123

Date:

Wed Jun 05 00:33:35 2019 +0000

Commit message:

works

Changed in this revision

--- /dev/null	Thu Jan 01 00:00:00 1970 +0000
+++ b/BufferedSerial.lib	Wed Jun 05 00:33:35 2019 +0000
@@ -0,0 +1,1 @@
+https://mbed.org/users/sam_grove/code/BufferedSerial/#a0d37088b405

--- /dev/null	Thu Jan 01 00:00:00 1970 +0000
+++ b/PinMap.h	Wed Jun 05 00:33:35 2019 +0000
@@ -0,0 +1,51 @@
+/*
+ * Copyright (c) 2017 Helmut Tschemernjak
+ * 30826 Garbsen (Hannover) Germany
+ * Licensed under the Apache License, Version 2.0);
+ */
+
+
+
+#ifdef TARGET_NUCLEO_L476RG
+ #define FEATURE_LORA   1
+#elif TARGET_DISCO_L072CZ_LRWAN1
+#define FEATURE_LORA   1
+#endif
+
+
+
+#if defined(TARGET_DISCO_L072CZ_LRWAN1)
+
+#define LORA_SPI_MOSI   PA_7
+#define LORA_SPI_MISO   PA_6
+#define LORA_SPI_SCLK   PB_3
+#define LORA_CS         PA_15
+#define LORA_RESET      PC_0
+#define LORA_DIO0       PB_4
+#define LORA_DIO1       PB_1
+#define LORA_DIO2       PB_0
+#define LORA_DIO3       PC_13
+#define LORA_DIO4       PA_5
+#define LORA_DIO5       PA_4
+#define LORA_ANT_RX     PA_1
+#define LORA_ANT_TX     PC_2
+#define LORA_ANT_BOOST  PC_1
+#define LORA_TCXO       PA_12   // 32 MHz
+
+
+
+#elif defined(TARGET_NUCLEO_L476RG) // using the RFM95 board
+
+#define LORA_SPI_MOSI   PC_12
+#define LORA_SPI_MISO   PC_11
+#define LORA_SPI_SCLK   PC_10
+#define LORA_CS         PA_0
+#define LORA_RESET      PA_1
+#define LORA_DIO0       PD_2    // DIO0=TxDone/RXDone
+#define LORA_DIO1       PB_7    //
+#define LORA_DIO2       PC_14   // DIO2=FhssChangeChannel
+#define LORA_DIO3       PC_15   // DIO3=CADDone
+#define LORA_DIO4       PH_0    // ????
+#define LORA_DIO5       NC      // unused?
+
+#endif

--- /dev/null	Thu Jan 01 00:00:00 1970 +0000
+++ b/SX1276GenericLib.lib	Wed Jun 05 00:33:35 2019 +0000
@@ -0,0 +1,1 @@
+https://os.mbed.com/users/TMRL123/code/SX1276GenericLib2/#eac0140d1d3b

--- /dev/null	Thu Jan 01 00:00:00 1970 +0000
+++ b/main.cpp	Wed Jun 05 00:33:35 2019 +0000
@@ -0,0 +1,280 @@
+/* Includes */
+#include "mbed.h" /* Mbed include */
+
+/* Lora includes */
+#include "PinMap.h"
+#include "sx1276-mbed-hal.h"
+
+/* Serial communication include */
+#include "BufferedSerial.h"
+
+/* Set this flag to '1' to display debug messages on the console */
+#define DEBUG_MESSAGE   1
+
+/* Set this flag to '1' to use the LoRa modulation or to '0' to use FSK modulation */
+#define USE_MODEM_LORA  1
+#define USE_MODEM_FSK   !USE_MODEM_LORA
+#define RF_FREQUENCY            RF_FREQUENCY_915_0 // Hz
+#define TX_OUTPUT_POWER         14                  // 14 dBm
+
+#if USE_MODEM_LORA == 1
+
+#define LORA_BANDWIDTH          125000  // LoRa default, details in SX1276::BandwidthMap
+#define LORA_SPREADING_FACTOR   LORA_SF7
+#define LORA_CODINGRATE         LORA_ERROR_CODING_RATE_4_5
+
+#define LORA_PREAMBLE_LENGTH    8       // Same for Tx and Rx
+#define LORA_SYMBOL_TIMEOUT     5       // Symbols
+#define LORA_FIX_LENGTH_PAYLOAD_ON  false
+#define LORA_FHSS_ENABLED       false  
+#define LORA_NB_SYMB_HOP        4     
+#define LORA_IQ_INVERSION_ON    false
+#define LORA_CRC_ENABLED        true
+    
+#endif 
+
+#define RX_TIMEOUT_VALUE    0       // In ms
+#define TX_TIMEOUT_VALUE    1000000 // In ms
+
+//#define BUFFER_SIZE       32        // Define the payload size here
+#define BUFFER_SIZE         64      // Define the payload size here
+
+typedef struct {
+            float p; // Pressure
+            float temperatureHTS221; // Temperature from HTS221
+            float humidity; // Humidity
+            float temperatureLPS22HB; // Temperature from LPS22HB
+            int32_t w[3]; // Angular velocity
+            int32_t a[3]; // Acceleration of the accelerometer LSM303AGR
+            int32_t ag[3]; // Acceleration of the accelerometer and gyroscope LSM6DSL 
+            int32_t m [3]; // Heading 
+}Dados; // Data struct
+        
+Dados dados;
+
+/* LoRa modem instances and configurations */
+
+static RadioEvents_t RadioEvents; // Calback functions struct
+
+SX1276Generic *Radio; // Definition of a Radio object
+
+bool received = false; // Flag to indicate the end of reception
+
+/* Configuration function */
+void SystemClock_Config(void);
+
+/* Callback functions prototypes */
+
+// Brief Function to be executed on Radio Tx Done event
+void OnTxDone(void *radio, void *userThisPtr, void *userData);
+
+// Brief Function to be executed on Radio Rx Done event
+void OnRxDone(void *radio, void *userThisPtr, void *userData, uint8_t *payload, uint16_t size, int16_t rssi, int8_t snr );
+
+// Brief Function executed on Radio Tx Timeout event
+void OnTxTimeout(void *radio, void *userThisPtr, void *userData);
+
+// Brief Function executed on Radio Rx Timeout event
+void OnRxTimeout(void *radio, void *userThisPtr, void *userData);
+
+// Brief Function executed on Radio Rx Error event
+void OnRxError(void *radio, void *userThisPtr, void *userData);
+
+// Brief Function executed on Radio Fhss Change Channel event
+void OnFhssChangeChannel(void *radio, void *userThisPtr, void *userData, uint8_t channelIndex);
+
+// Brief Function executed on CAD Done event
+void OnCadDone(void *radio, void *userThisPtr, void *userData);
+
+/* Serial communication to debug program */
+BufferedSerial *ser;
+
+int main() {
+    SystemClock_Config(); /* Synchronize clock for TX and RX boards */
+    
+    /* Serial configuration */
+    if (DEBUG_MESSAGE) {
+        ser = new BufferedSerial(USBTX, USBRX);
+        ser->baud(115200);
+        ser->format(8);
+    }
+    
+    /* General Header*/
+    if (DEBUG_MESSAGE)
+        ser->printf("Telemetry Rx inicial version program\r\n\r\n");
+    
+    Radio = new SX1276Generic(NULL, MURATA_SX1276,
+            LORA_SPI_MOSI, LORA_SPI_MISO, LORA_SPI_SCLK, LORA_CS, LORA_RESET,
+            LORA_DIO0, LORA_DIO1, LORA_DIO2, LORA_DIO3, LORA_DIO4, LORA_DIO5,
+            LORA_ANT_RX, LORA_ANT_TX, LORA_ANT_BOOST, LORA_TCXO);
+    
+    if (DEBUG_MESSAGE) {        
+        ser->printf("SX1276 Simple receiver aplication\r\n" );
+        ser->printf("Frequency: %.1f\r\n", (double)RF_FREQUENCY/1000000.0);
+        ser->printf("TXPower: %d dBm\r\n",  TX_OUTPUT_POWER);
+        ser->printf("Bandwidth: %d Hz\r\n", LORA_BANDWIDTH);
+        ser->printf("Spreading factor: SF%d\r\n", LORA_SPREADING_FACTOR);
+    }
+    
+    // Initialize Radio driver
+    RadioEvents.TxDone = OnTxDone;
+    RadioEvents.RxDone = OnRxDone;
+    RadioEvents.RxError = OnRxError;
+    RadioEvents.TxTimeout = OnTxTimeout;
+    RadioEvents.RxTimeout = OnRxTimeout; 
+    
+    // Initializes the radio    
+    while (Radio->Init( &RadioEvents ) == false) {
+        if (DEBUG_MESSAGE)
+            ser->printf("Radio could not be detected!\r\n");
+        wait( 1 );
+    }
+    
+    // Display the board type
+    switch(Radio->DetectBoardType()) {
+        case SX1276MB1LAS:
+            if (DEBUG_MESSAGE)
+                ser->printf(" > Board Type: SX1276MB1LAS <\r\n");
+            break;
+        case SX1276MB1MAS:
+            if (DEBUG_MESSAGE)
+                ser->printf(" > Board Type: SX1276MB1LAS <\r\n");
+        case MURATA_SX1276:
+            if (DEBUG_MESSAGE)
+                ser->printf(" > Board Type: MURATA_SX1276_STM32L0 <\r\n");
+            break;
+        case RFM95_SX1276:
+            if (DEBUG_MESSAGE) 
+                ser->printf(" > HopeRF RFM95xx <\r\n");
+            break;
+        default:
+            if (DEBUG_MESSAGE)
+                ser->printf(" > Board Type: unknown <\r\n");
+    }
+    
+    Radio->SetChannel(RF_FREQUENCY ); // Sets the frequency of the communication
+    
+    // Debug message of the state of fhss
+    if (LORA_FHSS_ENABLED) {
+        if (DEBUG_MESSAGE)
+            ser->printf("             > LORA FHSS Mode <\r\n");
+    }    
+    if (!LORA_FHSS_ENABLED) {
+        if (DEBUG_MESSAGE)
+            ser->printf("             > LORA Mode <\r\n");
+    }
+    // Sets the configuration of the transmission     
+    Radio->SetTxConfig( MODEM_LORA, TX_OUTPUT_POWER, 0, LORA_BANDWIDTH,
+                         LORA_SPREADING_FACTOR, LORA_CODINGRATE,
+                         LORA_PREAMBLE_LENGTH, LORA_FIX_LENGTH_PAYLOAD_ON,
+                         LORA_CRC_ENABLED, LORA_FHSS_ENABLED, LORA_NB_SYMB_HOP, 
+                         LORA_IQ_INVERSION_ON, 2000 );
+    
+    // Sets the configuration of the reception
+    Radio->SetRxConfig( MODEM_LORA, LORA_BANDWIDTH, LORA_SPREADING_FACTOR,
+                         LORA_CODINGRATE, 0, LORA_PREAMBLE_LENGTH,
+                         LORA_SYMBOL_TIMEOUT, LORA_FIX_LENGTH_PAYLOAD_ON, 0,
+                         LORA_CRC_ENABLED, LORA_FHSS_ENABLED, LORA_NB_SYMB_HOP, 
+                         LORA_IQ_INVERSION_ON, true );
+    if (DEBUG_MESSAGE)
+        ser->printf("Starting Receive loop\r\n"); 
+        
+    Radio->Rx(RX_TIMEOUT_VALUE); // Puts the device in reception mode continuously
+    
+    while( 1 )
+    {   
+        //After the receiving, puts the device again in receive mode 
+        if (received == true) {
+            received = false;
+            Radio->Rx(RX_TIMEOUT_VALUE); 
+        }
+    }
+    
+}
+
+
+void SystemClock_Config(void)
+{
+#ifdef B_L072Z_LRWAN1_LORA
+    /* 
+     * The L072Z_LRWAN1_LORA clock setup is somewhat differnt from the Nucleo board.
+     * It has no LSE.
+     */
+    RCC_ClkInitTypeDef RCC_ClkInitStruct = {0};
+    RCC_OscInitTypeDef RCC_OscInitStruct = {0};
+
+    /* Enable HSE Oscillator and Activate PLL with HSE as source */
+    RCC_OscInitStruct.OscillatorType      = RCC_OSCILLATORTYPE_HSI;
+    RCC_OscInitStruct.HSEState            = RCC_HSE_OFF;
+    RCC_OscInitStruct.HSIState            = RCC_HSI_ON;
+    RCC_OscInitStruct.HSICalibrationValue = RCC_HSICALIBRATION_DEFAULT;
+    RCC_OscInitStruct.PLL.PLLState        = RCC_PLL_ON;
+    RCC_OscInitStruct.PLL.PLLSource       = RCC_PLLSOURCE_HSI;
+    RCC_OscInitStruct.PLL.PLLMUL          = RCC_PLLMUL_6;
+    RCC_OscInitStruct.PLL.PLLDIV          = RCC_PLLDIV_3;
+
+    if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK) {
+        // Error_Handler();
+    }
+
+    /* Set Voltage scale1 as MCU will run at 32MHz */
+    __HAL_RCC_PWR_CLK_ENABLE();
+    __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE1);
+
+    /* Poll VOSF bit of in PWR_CSR. Wait until it is reset to 0 */
+    while (__HAL_PWR_GET_FLAG(PWR_FLAG_VOS) != RESET) {};
+
+    /* Select PLL as system clock source and configure the HCLK, PCLK1 and PCLK2
+    clocks dividers */
+    RCC_ClkInitStruct.ClockType = (RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2);
+    RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
+    RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
+    RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV1;
+    RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV1;
+    if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_1) != HAL_OK) {
+        // Error_Handler();
+    }
+#endif
+}
+
+void OnTxDone(void *radio, void *userThisPtr, void *userData)
+{
+    Radio->Sleep( );
+    if (DEBUG_MESSAGE)
+        ser->printf("> OnTxDone\r\n");
+}
+
+void OnRxDone(void *radio, void *userThisPtr, void *userData, uint8_t *payload, uint16_t size, int16_t rssi, int8_t snr)
+{
+    Radio->Sleep( );
+    received = true;
+    memcpy(&dados, payload, sizeof(dados));
+    if (DEBUG_MESSAGE) {
+        ser->printf("> OnRxDone: RssiValue=%d dBm, SnrValue=%d\r\n", rssi, snr);
+        ser->printf("I  received %d mg, %d mg, %d mg, %d mg, %d mg, %d mg, %d mdps, %d mdps, %d mdps\r\n", dados.a[0], dados.a[1], dados.a[2], dados.ag[0], dados.ag[1], dados.ag[2], dados.w[0], dados.w[1], dados.w[2]);
+        ser->printf("and %d mG, %d mG, %d mG, %g %%, %g C, %g C, %g mBar\r\n", dados.m[0], dados.m[1], dados.m[2], dados.humidity, dados.temperatureHTS221, dados.temperatureLPS22HB, dados.p);
+    }    
+
+}
+
+void OnTxTimeout(void *radio, void *userThisPtr, void *userData)
+{
+    Radio->Sleep( );
+    if(DEBUG_MESSAGE)
+        ser->printf("> OnTxTimeout\r\n");
+}
+
+void OnRxTimeout(void *radio, void *userThisPtr, void *userData)
+{
+    Radio->Sleep( );
+    if (DEBUG_MESSAGE)
+        ser->printf("> OnRxTimeout\r\n");
+}
+
+void OnRxError(void *radio, void *userThisPtr, void *userData)
+{
+    Radio->Sleep( );
+    received = true;
+    if (DEBUG_MESSAGE)
+        ser->printf("> OnRxError\r\n");
+}
\ No newline at end of file

--- /dev/null	Thu Jan 01 00:00:00 1970 +0000
+++ b/mbed.bld	Wed Jun 05 00:33:35 2019 +0000
@@ -0,0 +1,1 @@
+https://os.mbed.com/users/mbed_official/code/mbed/builds/65be27845400
\ No newline at end of file