Dmitry Kovalev
fork
system_LPC17xx.c
- Committer:
- Kovalev_D
- Date:
- 2017-09-04
- Revision:
- 217:15cd8752bb6c
- Parent:
- 214:4c70e452c491
File content as of revision 217:15cd8752bb6c:
/**************************************************************************//**
* @file system_LPC17xx.c
* @brief CMSIS Cortex-M3 Device Peripheral Access Layer Source File
* for the NXP LPC17xx Device Series
* @version V1.03
* @date 07. October 2009
*
* @note
* Copyright (C) 2009 ARM Limited. All rights reserved.
*
* @par
* ARM Limited (ARM) is supplying this software for use with Cortex-M
* processor based microcontrollers. This file can be freely distributed
* within development tools that are supporting such ARM based processors.
*
* @par
* THIS SOFTWARE IS PROVIDED "AS IS". NO WARRANTIES, WHETHER EXPRESS, IMPLIED
* OR STATUTORY, INCLUDING, BUT NOT LIMITED TO, IMPLIED WARRANTIES OF
* MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE APPLY TO THIS SOFTWARE.
* ARM SHALL NOT, IN ANY CIRCUMSTANCES, BE LIABLE FOR SPECIAL, INCIDENTAL, OR
* CONSEQUENTIAL DAMAGES, FOR ANY REASON WHATSOEVER.
*
******************************************************************************/
#include <stdint.h>
#include "LPC17xx.h"
/*
//-------- <<< Use Configuration Wizard in Context Menu >>> ------------------
*/
/*--------------------- Clock Configuration ----------------------------------
//
// <e> Clock Configuration
// <h> System Controls and Status Register (SCS)
// <o1.4> OSCRANGE: Main Oscillator Range Select
// <0=> 1 MHz to 20 MHz
// <1=> 15 MHz to 24 MHz
// <e1.5> OSCEN: Main Oscillator Enable
// </e>
// </h>
//
// <h> Clock Source Select Register (CLKSRCSEL)
// <o2.0..1> CLKSRC: PLL Clock Source Selection
// <0=> Internal RC oscillator
// <1=> Main oscillator
// <2=> RTC oscillator
// </h>
//
// <e3> PLL0 Configuration (Main PLL)
// <h> PLL0 Configuration Register (PLL0CFG)
// <i> F_cco0 = (2 * M * F_in) / N
// <i> F_in must be in the range of 32 kHz to 50 MHz
// <i> F_cco0 must be in the range of 275 MHz to 550 MHz
// <o4.0..14> MSEL: PLL Multiplier Selection
// <6-32768><#-1>
// <i> M Value
// <o4.16..23> NSEL: PLL Divider Selection
// <1-256><#-1>
// <i> N Value
// </h>
// </e>
//
// <e5> PLL1 Configuration (USB PLL)
// <h> PLL1 Configuration Register (PLL1CFG)
// <i> F_usb = M * F_osc or F_usb = F_cco1 / (2 * P)
// <i> F_cco1 = F_osc * M * 2 * P
// <i> F_cco1 must be in the range of 156 MHz to 320 MHz
// <o6.0..4> MSEL: PLL Multiplier Selection
// <1-32><#-1>
// <i> M Value (for USB maximum value is 4)
// <o6.5..6> PSEL: PLL Divider Selection
// <0=> 1
// <1=> 2
// <2=> 4
// <3=> 8
// <i> P Value
// </h>
// </e>
//
// <h> CPU Clock Configuration Register (CCLKCFG)
// <o7.0..7> CCLKSEL: Divide Value for CPU Clock from PLL0
// <3-256><#-1>
// </h>
//
// <h> USB Clock Configuration Register (USBCLKCFG)
// <o8.0..3> USBSEL: Divide Value for USB Clock from PLL0
// <0-15>
// <i> Divide is USBSEL + 1
// </h>
//
// <h> Peripheral Clock Selection Register 0 (PCLKSEL0)
// <o9.0..1> PCLK_WDT: Peripheral Clock Selection for WDT
// <0=> Pclk = Cclk / 4
// <1=> Pclk = Cclk
// <2=> Pclk = Cclk / 2
// <3=> Pclk = Hclk / 8
// <o9.2..3> PCLK_TIMER0: Peripheral Clock Selection for TIMER0
// <0=> Pclk = Cclk / 4
// <1=> Pclk = Cclk
// <2=> Pclk = Cclk / 2
// <3=> Pclk = Hclk / 8
// <o9.4..5> PCLK_TIMER1: Peripheral Clock Selection for TIMER1
// <0=> Pclk = Cclk / 4
// <1=> Pclk = Cclk
// <2=> Pclk = Cclk / 2
// <3=> Pclk = Hclk / 8
// <o9.6..7> PCLK_UART0: Peripheral Clock Selection for UART0
// <0=> Pclk = Cclk / 4
// <1=> Pclk = Cclk
// <2=> Pclk = Cclk / 2
// <3=> Pclk = Hclk / 8
// <o9.8..9> PCLK_UART1: Peripheral Clock Selection for UART1
// <0=> Pclk = Cclk / 4
// <1=> Pclk = Cclk
// <2=> Pclk = Cclk / 2
// <3=> Pclk = Hclk / 8
// <o9.12..13> PCLK_PWM1: Peripheral Clock Selection for PWM1
// <0=> Pclk = Cclk / 4
// <1=> Pclk = Cclk
// <2=> Pclk = Cclk / 2
// <3=> Pclk = Hclk / 8
// <o9.14..15> PCLK_I2C0: Peripheral Clock Selection for I2C0
// <0=> Pclk = Cclk / 4
// <1=> Pclk = Cclk
// <2=> Pclk = Cclk / 2
// <3=> Pclk = Hclk / 8
// <o9.16..17> PCLK_SPI: Peripheral Clock Selection for SPI
// <0=> Pclk = Cclk / 4
// <1=> Pclk = Cclk
// <2=> Pclk = Cclk / 2
// <3=> Pclk = Hclk / 8
// <o9.20..21> PCLK_SSP1: Peripheral Clock Selection for SSP1
// <0=> Pclk = Cclk / 4
// <1=> Pclk = Cclk
// <2=> Pclk = Cclk / 2
// <3=> Pclk = Hclk / 8
// <o9.22..23> PCLK_DAC: Peripheral Clock Selection for DAC
// <0=> Pclk = Cclk / 4
// <1=> Pclk = Cclk
// <2=> Pclk = Cclk / 2
// <3=> Pclk = Hclk / 8
// <o9.24..25> PCLK_ADC: Peripheral Clock Selection for ADC
// <0=> Pclk = Cclk / 4
// <1=> Pclk = Cclk
// <2=> Pclk = Cclk / 2
// <3=> Pclk = Hclk / 8
// <o9.26..27> PCLK_CAN1: Peripheral Clock Selection for CAN1
// <0=> Pclk = Cclk / 4
// <1=> Pclk = Cclk
// <2=> Pclk = Cclk / 2
// <3=> Pclk = Hclk / 6
// <o9.28..29> PCLK_CAN2: Peripheral Clock Selection for CAN2
// <0=> Pclk = Cclk / 4
// <1=> Pclk = Cclk
// <2=> Pclk = Cclk / 2
// <3=> Pclk = Hclk / 6
// <o9.30..31> PCLK_ACF: Peripheral Clock Selection for ACF
// <0=> Pclk = Cclk / 4
// <1=> Pclk = Cclk
// <2=> Pclk = Cclk / 2
// <3=> Pclk = Hclk / 6
// </h>
//
// <h> Peripheral Clock Selection Register 1 (PCLKSEL1)
// <o10.0..1> PCLK_QEI: Peripheral Clock Selection for the Quadrature Encoder Interface
// <0=> Pclk = Cclk / 4
// <1=> Pclk = Cclk
// <2=> Pclk = Cclk / 2
// <3=> Pclk = Hclk / 8
// <o10.2..3> PCLK_GPIO: Peripheral Clock Selection for GPIOs
// <0=> Pclk = Cclk / 4
// <1=> Pclk = Cclk
// <2=> Pclk = Cclk / 2
// <3=> Pclk = Hclk / 8
// <o10.4..5> PCLK_PCB: Peripheral Clock Selection for the Pin Connect Block
// <0=> Pclk = Cclk / 4
// <1=> Pclk = Cclk
// <2=> Pclk = Cclk / 2
// <3=> Pclk = Hclk / 8
// <o10.6..7> PCLK_I2C1: Peripheral Clock Selection for I2C1
// <0=> Pclk = Cclk / 4
// <1=> Pclk = Cclk
// <2=> Pclk = Cclk / 2
// <3=> Pclk = Hclk / 8
// <o10.10..11> PCLK_SSP0: Peripheral Clock Selection for SSP0
// <0=> Pclk = Cclk / 4
// <1=> Pclk = Cclk
// <2=> Pclk = Cclk / 2
// <3=> Pclk = Hclk / 8
// <o10.12..13> PCLK_TIMER2: Peripheral Clock Selection for TIMER2
// <0=> Pclk = Cclk / 4
// <1=> Pclk = Cclk
// <2=> Pclk = Cclk / 2
// <3=> Pclk = Hclk / 8
// <o10.14..15> PCLK_TIMER3: Peripheral Clock Selection for TIMER3
// <0=> Pclk = Cclk / 4
// <1=> Pclk = Cclk
// <2=> Pclk = Cclk / 2
// <3=> Pclk = Hclk / 8
// <o10.16..17> PCLK_UART2: Peripheral Clock Selection for UART2
// <0=> Pclk = Cclk / 4
// <1=> Pclk = Cclk
// <2=> Pclk = Cclk / 2
// <3=> Pclk = Hclk / 8
// <o10.18..19> PCLK_UART3: Peripheral Clock Selection for UART3
// <0=> Pclk = Cclk / 4
// <1=> Pclk = Cclk
// <2=> Pclk = Cclk / 2
// <3=> Pclk = Hclk / 8
// <o10.20..21> PCLK_I2C2: Peripheral Clock Selection for I2C2
// <0=> Pclk = Cclk / 4
// <1=> Pclk = Cclk
// <2=> Pclk = Cclk / 2
// <3=> Pclk = Hclk / 8
// <o10.22..23> PCLK_I2S: Peripheral Clock Selection for I2S
// <0=> Pclk = Cclk / 4
// <1=> Pclk = Cclk
// <2=> Pclk = Cclk / 2
// <3=> Pclk = Hclk / 8
// <o10.26..27> PCLK_RIT: Peripheral Clock Selection for the Repetitive Interrupt Timer
// <0=> Pclk = Cclk / 4
// <1=> Pclk = Cclk
// <2=> Pclk = Cclk / 2
// <3=> Pclk = Hclk / 8
// <o10.28..29> PCLK_SYSCON: Peripheral Clock Selection for the System Control Block
// <0=> Pclk = Cclk / 4
// <1=> Pclk = Cclk
// <2=> Pclk = Cclk / 2
// <3=> Pclk = Hclk / 8
// <o10.30..31> PCLK_MC: Peripheral Clock Selection for the Motor Control PWM
// <0=> Pclk = Cclk / 4
// <1=> Pclk = Cclk
// <2=> Pclk = Cclk / 2
// <3=> Pclk = Hclk / 8
// </h>
//
// <h> Power Control for Peripherals Register (PCONP)
// <o11.1> PCTIM0: Timer/Counter 0 power/clock enable
// <o11.2> PCTIM1: Timer/Counter 1 power/clock enable
// <o11.3> PCUART0: UART 0 power/clock enable
// <o11.4> PCUART1: UART 1 power/clock enable
// <o11.6> PCPWM1: PWM 1 power/clock enable
// <o11.7> PCI2C0: I2C interface 0 power/clock enable
// <o11.8> PCSPI: SPI interface power/clock enable
// <o11.9> PCRTC: RTC power/clock enable
// <o11.10> PCSSP1: SSP interface 1 power/clock enable
// <o11.12> PCAD: A/D converter power/clock enable
// <o11.13> PCCAN1: CAN controller 1 power/clock enable
// <o11.14> PCCAN2: CAN controller 2 power/clock enable
// <o11.15> PCGPIO: GPIOs power/clock enable
// <o11.16> PCRIT: Repetitive interrupt timer power/clock enable
// <o11.17> PCMC: Motor control PWM power/clock enable
// <o11.18> PCQEI: Quadrature encoder interface power/clock enable
// <o11.19> PCI2C1: I2C interface 1 power/clock enable
// <o11.21> PCSSP0: SSP interface 0 power/clock enable
// <o11.22> PCTIM2: Timer 2 power/clock enable
// <o11.23> PCTIM3: Timer 3 power/clock enable
// <o11.24> PCUART2: UART 2 power/clock enable
// <o11.25> PCUART3: UART 3 power/clock enable
// <o11.26> PCI2C2: I2C interface 2 power/clock enable
// <o11.27> PCI2S: I2S interface power/clock enable
// <o11.29> PCGPDMA: GP DMA function power/clock enable
// <o11.30> PCENET: Ethernet block power/clock enable
// <o11.31> PCUSB: USB interface power/clock enable
// </h>
//
// <h> Clock Output Configuration Register (CLKOUTCFG)
// <o12.0..3> CLKOUTSEL: Selects clock source for CLKOUT
// <0=> CPU clock
// <1=> Main oscillator
// <2=> Internal RC oscillator
// <3=> USB clock
// <4=> RTC oscillator
// <o12.4..7> CLKOUTDIV: Selects clock divider for CLKOUT
// <1-16><#-1>
// <o12.8> CLKOUT_EN: CLKOUT enable control
// </h>
//
// </e>
*/
// сейчас получается частота 100 Mhz
//12 * 2 * (99+1) / (5+1) = 400 (должна быть в пределах 275...550)
//потом еше делится на 4 = 100
//нам нужно 921600* 16 = 14 745 000, теперб выбираем делитель уартовский 7 = 103 219 200, дибо 8 = 117 964 800
//1 выбираем второе 117 964 800 округляем до 100 000 (для второго таймера) 118 000. таку. частоту нужно на входе УАРТА.
//118 * 3 = 354, 118 * 4 = 472.
// 354 / "3" = 118
//попробуем с 474 >> умножитель на 59 и делитель на 3 => 12 * 2 * ("58" + 1) / ("2" + 1) = 472.
// 472 / "4" = 118
// с другой стороны не рекомендуют частоты выше 100 (120 только для 1769 или чото там еще )
// 103,200 => *3 = 309.6; * 4 = 412,8.
// 412,8 умножитель на 86 и делитель на 5 => 12 * 2 * ("85" + 1) / ("4" + 1) = 412,8. !!!!!наверно можно остоновиься и попробовать!!!!!!!!
// 412,8 / "4" = 103,2
#define CLOCK_SETUP 1
//System control - system control and status register:
// bit 4 - main oscillator range:
// 0 - 1...20MHz
// 1 - 15...25MHz
// bit 5 - main oscillator enable
// 0 - disabled
// 1 - enabled
// bit 6 - main oscillator status
// 0 - not ready
// 1 - ready
#define SCS_Val 0x00000020 //Enable main oscillator,1...20MHz
//Clock Source Select register
// bits 0-1:
// 00 - Selects the Internal RC oscillator as the PLL0 clock source (default)
// 01 - Selects the main oscillator as the PLL0 clock source
// 10 - Selects the RTC oscillator as the PLL0 clock source
// 11 - Reserved, do not use this setting
#define CLKSRCSEL_Val 0x00000001//Select the main oscillator as the PLL0 clock source
#define PLL0_SETUP 1
//PLL0 Configuration register
// bits 0...14 - PLL0 multiplier value minus 1. Supported multiplier M range 6...512
// bits 16...23 - PLL0 Pre-Divider value minus 1. Supported divider N range 1...32
// Fcc0 = (2 * M * Fin) / N
#define PLL0CFG_Val 0x00040055//M - 86, N - 5, output = 2 * 86 * 12MHz / 5 = 400MHz
// #define PLL0CFG_Val 0x0003003d//M - 86, N - 5, output = 2 * 86 * 12MHz / 5 = 400MHz
#define PLL1_SETUP 1
#define PLL1CFG_Val 0x00000023//M - 36, N - 1, output = 2 * 36 * 12MHz / 1 = 864MHz?
//CPU Clock Configure Register
#define CCLKCFG_Val 0x00000003 //Divide by 4
//USB Clock Configuration register
// bits 0...3
// 5 - PLL0 output is divided by 6. PLL0 output must be 288 MHz
// 7 - PLL0 output is divided by 8. PLL0 output must be 384 MHz
// 9 - PLL0 output is divided by 10. PLL0 output must be 480 MHz
#define USBCLKCFG_Val 0x00000000//default
//Peripheral Clock Selection register 0
// 1:0 PCLK_WDT Peripheral clock selection for WDT. 00
// 3:2 PCLK_TIMER0 Peripheral clock selection for TIMER0. 00
// 5:4 PCLK_TIMER1 Peripheral clock selection for TIMER1. 00
// 7:6 PCLK_UART0 Peripheral clock selection for UART0. 00
// 9:8 PCLK_UART1 Peripheral clock selection for UART1. 00
// 11:10 - Reserved. NA
// 13:12 PCLK_PWM1 Peripheral clock selection for PWM1. 00
// 15:14 PCLK_I2C0 Peripheral clock selection for I2C0. 00
// 17:16 PCLK_SPI Peripheral clock selection for SPI. 00
// 19:18 - Reserved. NA
// 21:20 PCLK_SSP1 Peripheral clock selection for SSP1. 00
// 23:22 PCLK_DAC Peripheral clock selection for DAC. 00
// 25:24 PCLK_ADC Peripheral clock selection for ADC. 00
// 27:26 PCLK_CAN1 Peripheral clock selection for CAN1.[1] 00
// 29:28 PCLK_CAN2 Peripheral clock selection for CAN2.[1] 00
// 31:30 PCLK_ACF Peripheral clock selection for CAN acceptance filtering
// bits values:
// 00 PCLK_peripheral = CCLK/4
// 01 PCLK_peripheral = CCLK
// 10 PCLK_peripheral = CCLK/2
// 11 PCLK_peripheral = CCLK/8, except for CAN1, CAN2, and CAN filtering when “11” selects = CCLK/6.
//#define PCLKSEL0_Val 0x00000010//Peripheral clock selection for TIMER1 - CCLK, other peripherals - CCLK/4
#define PCLKSEL0_Val 0x40000150//Peripheral clock selection for TIMER1 - CCLK, other peripherals - CCLK/4
//#define PCLKSEL0_Val 0x000003d0//Peripheral clock selection for TIMER1 - CCLK, other peripherals - CCLK/4
//Peripheral Clock Selection register 1
// 1:0 PCLK_QEI Peripheral clock selection for the Quadrature Encoder Interface.00
// 3:2 PCLK_GPIOINT Peripheral clock selection for GPIO interrupts. 00
// 5:4 PCLK_PCB Peripheral clock selection for the Pin Connect block. 00
// 7:6 PCLK_I2C1 Peripheral clock selection for I2C1. 00
// 9:8 - Reserved. NA
// 11:10 PCLK_SSP0 Peripheral clock selection for SSP0. 00
// 13:12 PCLK_TIMER2 Peripheral clock selection for TIMER2. 00
// 15:14 PCLK_TIMER3 Peripheral clock selection for TIMER3. 00
// 17:16 PCLK_UART2 Peripheral clock selection for UART2. 00
// 19:18 PCLK_UART3 Peripheral clock selection for UART3. 00
// 21:20 PCLK_I2C2 Peripheral clock selection for I2C2. 00
// 23:22 PCLK_I2S Peripheral clock selection for I2S. 00
// 25:24 - Reserved. NA
// 27:26 PCLK_RIT Peripheral clock selection for Repetitive Interrupt Timer. 00
// 29:28 PCLK_SYSCON Peripheral clock selection for the System Control block. 00
// 31:30 PCLK_MC Peripheral clock selection for the Motor Control PWM
#define PCLKSEL1_Val 0x00000000//CCLK/4
//Power Control for Peripherals register
//0 - Reserved. NA
//1 PCTIM0 Timer/Counter 0 power/clock control bit. 1
//2 PCTIM1 Timer/Counter 1 power/clock control bit. 1
//3 PCUART0 UART0 power/clock control bit. 1
//4 PCUART1 UART1 power/clock control bit. 1
//5 - Reserved. NA
//6 PCPWM1 PWM1 power/clock control bit. 1
//7 PCI2C0 The I2C0 interface power/clock control bit. 1
//8 PCSPI The SPI interface power/clock control bit. 1
//9 PCRTC The RTC power/clock control bit. 1
//10 PCSSP1 The SSP 1 interface power/clock control bit. 1
//11 - Reserved. NA
//12 PCADC A/D converter (ADC) power/clock control bit. Note: Clear the PDN bit in the AD0CR before clearing this bit, and set this bit before setting PDN. 0
//13 PCCAN1 CAN Controller 1 power/clock control bit. 0
//14 PCCAN2 CAN Controller 2 power/clock control bit. 0
//15 PCGPIO Power/clock control bit for IOCON, GPIO, and GPIO interrupts. 1
//16 PCRIT Repetitive Interrupt Timer power/clock control bit. 0
//17 PCMCPWM Motor Control PWM 0
//18 PCQEI Quadrature Encoder Interface power/clock control bit. 0
//19 PCI2C1 The I2C1 interface power/clock control bit. 1
//20 - Reserved. NA
//21 PCSSP0 The SSP0 interface power/clock control bit. 1
//22 PCTIM2 Timer 2 power/clock control bit. 0
//23 PCTIM3 Timer 3 power/clock control bit. 0
//24 PCUART2 UART 2 power/clock control bit. 0
//25 PCUART3 UART 3 power/clock control bit. 0
//26 PCI2C2 I2C interface 2 power/clock control bit. 1
#define PCONP_Val 0x046887DE//ADC,CAN1/2,RIT,Timer3,UART2,UART3 disabled
//Clock Output Configuration register
// 3:0 CLKOUTSEL Selects the clock source for the CLKOUT function. 0
// 0000 Selects the CPU clock as the CLKOUT source.
// 0001 Selects the main oscillator as the CLKOUT source.
// 0010 Selects the Internal RC oscillator as the CLKOUT source.
// 0011 Selects the USB clock as the CLKOUT source.
// 0100 Selects the RTC oscillator as the CLKOUT source.
// Others Reserved, do not use these settings.
// 7:4 CLKOUTDIV Integer value to divide the output clock by, minus one. 0
// 0000 Clock is divided by 1.
// 0001 Clock is divided by 2.
// 0010 Clock is divided by 3.
// ... ...
// 1111 Clock is divided by 16.
// 8 CLKOUT_EN CLKOUT enable control, allows switching the CLKOUT source without glitches. Clear to stop CLKOUT on the next falling edge. Set to enable CLKOUT. 0
// 9 CLKOUT_ACT CLKOUT activity indication. Reads as 1 when CLKOUT is enabled. Read as 0 when CLKOUT has been disabled via the CLKOUT_EN bit and the clock has completed being stopped.
#define CLKOUTCFG_Val 0x00000000//Host4: CLKOUT pin not used
/*--------------------- Flash Accelerator Configuration ----------------------
//
// <e> Flash Accelerator Configuration
// <o1.0..1> FETCHCFG: Fetch Configuration
// <0=> Instruction fetches from flash are not buffered
// <1=> One buffer is used for all instruction fetch buffering
// <2=> All buffers may be used for instruction fetch buffering
// <3=> Reserved (do not use this setting)
// <o1.2..3> DATACFG: Data Configuration
// <0=> Data accesses from flash are not buffered
// <1=> One buffer is used for all data access buffering
// <2=> All buffers may be used for data access buffering
// <3=> Reserved (do not use this setting)
// <o1.4> ACCEL: Acceleration Enable
// <o1.5> PREFEN: Prefetch Enable
// <o1.6> PREFOVR: Prefetch Override
// <o1.12..15> FLASHTIM: Flash Access Time
// <0=> 1 CPU clock (for CPU clock up to 20 MHz)
// <1=> 2 CPU clocks (for CPU clock up to 40 MHz)
// <2=> 3 CPU clocks (for CPU clock up to 60 MHz)
// <3=> 4 CPU clocks (for CPU clock up to 80 MHz)
// <4=> 5 CPU clocks (for CPU clock up to 100 MHz)
// <5=> 6 CPU clocks (for any CPU clock)
// </e>
*/
#define FLASH_SETUP 1
//Flash Accelerator Configuration Register
// 11:0 - - Reserved, user software should not change these bits from the reset value. 0x03A
// 15:12 FLASHTIM Flash access time. The value of this field plus 1 gives the number of CPU clocks used for a flash access. Warning: improper setting of this value may result in incorrect operation of the device. 0x3
// 0000 Flash accesses use 1 CPU clock. Use for up to 20 MHz CPU clock.
// 0001 Flash accesses use 2 CPU clocks. Use for up to 40 MHz CPU clock.
// 0010 Flash accesses use 3 CPU clocks. Use for up to 60 MHz CPU clock.
// 0011 Flash accesses use 4 CPU clocks. Use for up to 80 MHz CPU clock.
// 0100 Flash accesses use 5 CPU clocks. Use for up to 100 MHz CPU clock. Use for up to 120 Mhz for LPC1759 and LPC1769 only.
// 0101 Flash accesses use 6 CPU clocks. This “safe” setting will work under any conditions. Other Intended for potential future higher speed devices.
// 31:16 - Reserved. The value read from a reserved bit is not defined. NA
#define FLASHCFG_Val 0x0000303A//5 CPU clocks required for flash access
/*
//-------- <<< end of configuration section >>> ------------------------------
*/
/*----------------------------------------------------------------------------
Check the register settings
*----------------------------------------------------------------------------*/
#define CHECK_RANGE(val, min, max) ((val < min) || (val > max))
#define CHECK_RSVD(val, mask) (val & mask)
/* Clock Configuration -------------------------------------------------------*/
#if (CHECK_RSVD((SCS_Val), ~0x00000030))
#error "SCS: Invalid values of reserved bits!"
#endif
#if (CHECK_RANGE((CLKSRCSEL_Val), 0, 2))
#error "CLKSRCSEL: Value out of range!"
#endif
#if (CHECK_RSVD((PLL0CFG_Val), ~0x00FF7FFF))
#error "PLL0CFG: Invalid values of reserved bits!"
#endif
#if (CHECK_RSVD((PLL1CFG_Val), ~0x0000007F))
#error "PLL1CFG: Invalid values of reserved bits!"
#endif
#if ((CCLKCFG_Val != 0) && (((CCLKCFG_Val - 1) % 2)))
#error "CCLKCFG: CCLKSEL field does not contain only odd values or 0!"
#endif
#if (CHECK_RSVD((USBCLKCFG_Val), ~0x0000000F))
#error "USBCLKCFG: Invalid values of reserved bits!"
#endif
#if (CHECK_RSVD((PCLKSEL0_Val), 0x000C0C00))
#error "PCLKSEL0: Invalid values of reserved bits!"
#endif
#if (CHECK_RSVD((PCLKSEL1_Val), 0x03000300))
#error "PCLKSEL1: Invalid values of reserved bits!"
#endif
#if (CHECK_RSVD((PCONP_Val), 0x10100821))
#error "PCONP: Invalid values of reserved bits!"
#endif
#if (CHECK_RSVD((CLKOUTCFG_Val), ~0x000001FF))
#error "CLKOUTCFG: Invalid values of reserved bits!"
#endif
/* Flash Accelerator Configuration -------------------------------------------*/
#if (CHECK_RSVD((FLASHCFG_Val), ~0x0000F07F))
#error "FLASHCFG: Invalid values of reserved bits!"
#endif
/*----------------------------------------------------------------------------
DEFINES
*----------------------------------------------------------------------------*/
/*----------------------------------------------------------------------------
Define clocks
*----------------------------------------------------------------------------*/
#define XTAL (12000000UL) /* Oscillator frequency */
#define OSC_CLK ( XTAL) /* Main oscillator frequency */
#define RTC_CLK ( 32000UL) /* RTC oscillator frequency */
#define IRC_OSC ( 4000000UL) /* Internal RC oscillator frequency */
/* F_cco0 = (2 * M * F_in) / N */
#define __M (((PLL0CFG_Val ) & 0x7FFF) + 1)
#define __N (((PLL0CFG_Val >> 16) & 0x00FF) + 1)
#define __FCCO(__F_IN) ((2 * __M * __F_IN) / __N)
#define __CCLK_DIV (((CCLKCFG_Val ) & 0x00FF) + 1)
/* Determine core clock frequency according to settings */
#if (PLL0_SETUP)
#if ((CLKSRCSEL_Val & 0x03) == 1)
#define __CORE_CLK (__FCCO(OSC_CLK) / __CCLK_DIV)
#elif ((CLKSRCSEL_Val & 0x03) == 2)
#define __CORE_CLK (__FCCO(RTC_CLK) / __CCLK_DIV)
#else
#define __CORE_CLK (__FCCO(IRC_OSC) / __CCLK_DIV)
#endif
#else
#if ((CLKSRCSEL_Val & 0x03) == 1)
#define __CORE_CLK (OSC_CLK / __CCLK_DIV)
#elif ((CLKSRCSEL_Val & 0x03) == 2)
#define __CORE_CLK (RTC_CLK / __CCLK_DIV)
#else
#define __CORE_CLK (IRC_OSC / __CCLK_DIV)
#endif
#endif
/*----------------------------------------------------------------------------
Clock Variable definitions
*----------------------------------------------------------------------------*/
uint32_t SystemFrequency = IRC_OSC;
uint32_t SystemCoreClock1 = __CORE_CLK;/*!< System Clock Frequency (Core Clock)*/
/*----------------------------------------------------------------------------
Clock functions
*----------------------------------------------------------------------------*/
void SystemCoreClockUpdate1 (void) /* Get Core Clock Frequency */
{
/* Determine clock frequency according to clock register values */
if (((LPC_SC->PLL0STAT >> 24) & 3) == 3) { /* If PLL0 enabled and connected */
switch (LPC_SC->CLKSRCSEL & 0x03) {
case 0: /* Int. RC oscillator => PLL0 */
case 3: /* Reserved, default to Int. RC */
SystemCoreClock1 = (IRC_OSC *
((2 * ((LPC_SC->PLL0STAT & 0x7FFF) + 1))) /
(((LPC_SC->PLL0STAT >> 16) & 0xFF) + 1) /
((LPC_SC->CCLKCFG & 0xFF)+ 1));
break;
case 1: /* Main oscillator => PLL0 */
SystemCoreClock1 = (OSC_CLK * //it is our case osc_clk = 12 MHz
((2 * ((LPC_SC->PLL0STAT & 0x7FFF) + 1))) / //PLL0 multiplier value
(((LPC_SC->PLL0STAT >> 16) & 0xFF) + 1) / //PLL0 pre-divider
((LPC_SC->CCLKCFG & 0xFF)+ 1)); //divider for CCLK (SystemCoreClock)
break;
case 2: /* RTC oscillator => PLL0 */
SystemCoreClock1 = (RTC_CLK *
((2 * ((LPC_SC->PLL0STAT & 0x7FFF) + 1))) /
(((LPC_SC->PLL0STAT >> 16) & 0xFF) + 1) /
((LPC_SC->CCLKCFG & 0xFF)+ 1));
break;
}
} else {
switch (LPC_SC->CLKSRCSEL & 0x03) {
case 0: /* Int. RC oscillator => PLL0 */
case 3: /* Reserved, default to Int. RC */
SystemCoreClock1 = IRC_OSC / ((LPC_SC->CCLKCFG & 0xFF)+ 1);
break;
case 1: /* Main oscillator => PLL0 */
SystemCoreClock1 = OSC_CLK / ((LPC_SC->CCLKCFG & 0xFF)+ 1);
break;
case 2: /* RTC oscillator => PLL0 */
SystemCoreClock1 = RTC_CLK / ((LPC_SC->CCLKCFG & 0xFF)+ 1);
break;
}
}
}
/**
* Initialize the system
*
* @param none
* @return none
*
* @brief Setup the microcontroller system.
* Initialize the System.
*/
void SystemInit1 (void)
{
#if (CLOCK_SETUP) /* Clock Setup */
//Init system control and status register
LPC_SC->SCS = SCS_Val;//0x20 - enable main oscillator,1...20MHz (12MHz)
if (SCS_Val & (1 << 5)) { /* If Main Oscillator is enabled */
while ((LPC_SC->SCS & (1<<6)) == 0);/* Wait for Oscillator to be ready */
}
//Init CPU Clock Configure Register - select the divide value for creating the CPU clock (CCLK) from the PLL0 output
LPC_SC->CCLKCFG = CCLKCFG_Val; //3 - divide to 4 (3MHz)
#if (PLL0_SETUP)
//Init Clock Source Select register
LPC_SC->CLKSRCSEL = CLKSRCSEL_Val;//1 - Select the main oscillator as the PLL0 clock source
//Init PLL0 Configuration register
LPC_SC->PLL0CFG = PLL0CFG_Val;//0x00050063: M - 100, N - 6, PLL0output = 2 * 100 * 12MHz / 6 = 400MHz, CPU clock 100MHz
//Init PLL0 Feed Register. This register enables loading of the PLL0 control and configuration information from the PLL0CON and PLL0CFG
//registers into the shadow registers that actually affect PLL0 operation.
//Write 0xAA and 0x55 sequentially to update shadow registers and settings to take effect
LPC_SC->PLL0FEED = 0xAA;
LPC_SC->PLL0FEED = 0x55;
//Init PLL0 Control register
// bit 0 - PLL0 Enable
// bit 1 - PLL0 connect
LPC_SC->PLL0CON = 0x01;//PLL0 Enable
//Update shadow registers to settings take effect
LPC_SC->PLL0FEED = 0xAA;
LPC_SC->PLL0FEED = 0x55;
//PLL0 Status register
// bits 0...14 - Read-back for the PLL0 Multiplier value
// bits 16...23 - Read-back for the PLL0 Pre-Divider value
// bit 24 - Read-back for the PLL0 Enable bit
// bit 25 - Read-back for the PLL0 Connect bit
// bit 26 - Reflects the PLL0 Lock status: 1 - locked
while (!(LPC_SC->PLL0STAT & (1<<26)));//Wait while PLL0 locked (PLOCK0)
LPC_SC->PLL0CON = 0x03;//PLL0 Enable & Connect
LPC_SC->PLL0FEED = 0xAA;
LPC_SC->PLL0FEED = 0x55;
while (!(LPC_SC->PLL0STAT & ((1<<25) | (1<<24))));//Wait while PLL0 connected (PLLC0_STAT & PLLE0_STAT)
#endif
#if (PLL1_SETUP)
LPC_SC->PLL1CFG = PLL1CFG_Val;//0x23 M - 36, N - 1, output = 2 * 36 * 12MHz / 1 = 864MHz?
LPC_SC->PLL1FEED = 0xAA;
LPC_SC->PLL1FEED = 0x55;
LPC_SC->PLL1CON = 0x01; /* PLL1 Enable */
LPC_SC->PLL1FEED = 0xAA;
LPC_SC->PLL1FEED = 0x55;
while (!(LPC_SC->PLL1STAT & (1<<10)));/* Wait for PLOCK1 */
LPC_SC->PLL1CON = 0x03; /* PLL1 Enable & Connect */
LPC_SC->PLL1FEED = 0xAA;
LPC_SC->PLL1FEED = 0x55;
while (!(LPC_SC->PLL1STAT & ((1<< 9) | (1<< 8))));/* Wait for PLLC1_STAT & PLLE1_STAT */
#else
LPC_SC->USBCLKCFG = USBCLKCFG_Val; /* Setup USB Clock Divider */
#endif
LPC_SC->PCLKSEL0 = PCLKSEL0_Val; /* Peripheral Clock Selection */
LPC_SC->PCLKSEL1 = PCLKSEL1_Val;
LPC_SC->PCONP = PCONP_Val; /* Power Control for Peripherals */
LPC_SC->CLKOUTCFG = CLKOUTCFG_Val; /* Clock Output Configuration */
#endif
#if (FLASH_SETUP == 1) /* Flash Accelerator Setup */
LPC_SC->FLASHCFG = FLASHCFG_Val;
#endif
}
void SystemInitDef (void)
{
#if (CLOCK_SETUP) /* Clock Setup */
LPC_SC->SCS = SCS_Val;
if (SCS_Val & (1 << 5)) { /* If Main Oscillator is enabled */
while ((LPC_SC->SCS & (1<<6)) == 0);/* Wait for Oscillator to be ready */
}
LPC_SC->CCLKCFG = CCLKCFG_Val; /* Setup Clock Divider */
LPC_SC->PCLKSEL0 = PCLKSEL0_Val; /* Peripheral Clock Selection */
LPC_SC->PCLKSEL1 = PCLKSEL1_Val;
#if (PLL0_SETUP)
LPC_SC->CLKSRCSEL = 0;// CLKSRCSEL_Val; /* Select Clock Source for PLL0 */
LPC_SC->PLL0CFG = PLL0CFG_Val;
LPC_SC->PLL0CON = 0x01; /* PLL0 Enable */
LPC_SC->PLL0FEED = 0xAA;
LPC_SC->PLL0FEED = 0x55;
while (!(LPC_SC->PLL0STAT & (1<<26)));/* Wait for PLOCK0 */
LPC_SC->PLL0CON = 0x03; /* PLL0 Enable & Connect */
LPC_SC->PLL0FEED = 0xAA;
LPC_SC->PLL0FEED = 0x55;
#endif
#if (PLL1_SETUP)
LPC_SC->PLL1CFG = PLL1CFG_Val;
LPC_SC->PLL1CON = 0x01; /* PLL1 Enable */
LPC_SC->PLL1FEED = 0xAA;
LPC_SC->PLL1FEED = 0x55;
while (!(LPC_SC->PLL1STAT & (1<<10)));/* Wait for PLOCK1 */
LPC_SC->PLL1CON = 0x03; /* PLL1 Enable & Connect */
LPC_SC->PLL1FEED = 0xAA;
LPC_SC->PLL1FEED = 0x55;
#else
LPC_SC->USBCLKCFG = USBCLKCFG_Val; /* Setup USB Clock Divider */
#endif
LPC_SC->PCONP = PCONP_Val; /* Power Control for Peripherals */
LPC_SC->CLKOUTCFG = CLKOUTCFG_Val; /* Clock Output Configuration */
#endif
/* Determine clock frequency according to clock register values */
if (((LPC_SC->PLL0STAT >> 24)&3)==3) {/* If PLL0 enabled and connected */
switch (LPC_SC->CLKSRCSEL & 0x03) {
case 0: /* Internal RC oscillator => PLL0 */
case 3: /* Reserved, default to Internal RC */
SystemFrequency = (IRC_OSC *
(((2 * ((LPC_SC->PLL0STAT & 0x7FFF) + 1))) /
(((LPC_SC->PLL0STAT >> 16) & 0xFF) + 1)) /
((LPC_SC->CCLKCFG & 0xFF)+ 1));
break;
case 1: /* Main oscillator => PLL0 */
SystemFrequency = (OSC_CLK *
(((2 * ((LPC_SC->PLL0STAT & 0x7FFF) + 1))) /
(((LPC_SC->PLL0STAT >> 16) & 0xFF) + 1)) /
((LPC_SC->CCLKCFG & 0xFF)+ 1));
break;
case 2: /* RTC oscillator => PLL0 */
SystemFrequency = (RTC_CLK *
(((2 * ((LPC_SC->PLL0STAT & 0x7FFF) + 1))) /
(((LPC_SC->PLL0STAT >> 16) & 0xFF) + 1)) /
((LPC_SC->CCLKCFG & 0xFF)+ 1));
break;
}
} else {
switch (LPC_SC->CLKSRCSEL & 0x03) {
case 0: /* Internal RC oscillator => PLL0 */
case 3: /* Reserved, default to Internal RC */
SystemFrequency = IRC_OSC / ((LPC_SC->CCLKCFG & 0xFF)+ 1);
break;
case 1: /* Main oscillator => PLL0 */
SystemFrequency = OSC_CLK / ((LPC_SC->CCLKCFG & 0xFF)+ 1);
break;
case 2: /* RTC oscillator => PLL0 */
SystemFrequency = RTC_CLK / ((LPC_SC->CCLKCFG & 0xFF)+ 1);
break;
}
}
#if (FLASH_SETUP == 1) /* Flash Accelerator Setup */
LPC_SC->FLASHCFG = FLASHCFG_Val;
#endif
}