Diff: init.cpp

Revision:

3:4a2dfa38a61e

Parent:

2:f163731f852a

Child:

8:6870e6801838

--- a/init.cpp	Thu Oct 03 14:46:22 2013 +0000
+++ b/init.cpp	Thu Oct 03 17:32:27 2013 +0200
@@ -1,54 +1,70 @@
-#include "main.h"
-
-#if (MY_BOARD == WIGO)
-
-#include "NVIC_set_all_priorities.h"
-
-/**
- *  \brief Wi-Go initialization
- *  \param none
- *  \return none
- */
-void init() {
-    DigitalOut PWR_EN1(PTB2);
-    DigitalOut PWR_EN2(PTB3);
-
-    // Wi-Go set current to 500mA since we're turning on the Wi-Fi
-    PWR_EN1 = 0;
-    PWR_EN2 = 1;
-
-    NVIC_set_all_irq_priorities(3);
-    NVIC_SetPriority(SPI0_IRQn, 0x0);     // Wi-Fi SPI interrupt must be higher priority than SysTick
-    NVIC_SetPriority(PORTA_IRQn, 0x1);
-    NVIC_SetPriority(SysTick_IRQn, 0x2);  // SysTick set to lower priority than Wi-Fi SPI bus interrupt
-    PORTA->PCR[16] |=PORT_PCR_ISF_MASK;
-    PORTA->ISFR |= (1 << 16);
-}
-
-#elif (MY_BOARD == WIFI_DIPCORTEX)
-
-/**
- *  \brief Wifi DipCortex initialization
- *  \param none
- *  \return none
- */
-void init() {
-    NVIC_SetPriority(SSP1_IRQn, 0x0);
-    NVIC_SetPriority(PIN_INT0_IRQn, 0x1);
-
-    // SysTick set to lower priority than Wi-Fi SPI bus interrupt
-    NVIC_SetPriority(SysTick_IRQn, 0x2);
-}
-
-#else
-
-/**
- *  \brief Place here init routine for your board
- *  \param none
- *  \return none
- */
-void init() {
-
-}
-
-#endif
+/* mbed Microcontroller Library
+ * Copyright (c) 2006-2013 ARM Limited
+ *
+ * Licensed under the Apache License, Version 2.0 (the "License");
+ * you may not use this file except in compliance with the License.
+ * You may obtain a copy of the License at
+ *
+ *     http://www.apache.org/licenses/LICENSE-2.0
+ *
+ * Unless required by applicable law or agreed to in writing, software
+ * distributed under the License is distributed on an "AS IS" BASIS,
+ * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+ * See the License for the specific language governing permissions and
+ * limitations under the License.
+ */
+#include "main.h"
+#include "mbed.h"
+
+#if (MY_BOARD == WIGO)
+
+#include "NVIC_set_all_priorities.h"
+
+/**
+ *  \brief Wi-Go initialization
+ *  \param none
+ *  \return none
+ */
+void init() {
+    DigitalOut PWR_EN1(PTB2);
+    DigitalOut PWR_EN2(PTB3);
+
+    // Wi-Go set current to 500mA since we're turning on the Wi-Fi
+    PWR_EN1 = 0;
+    PWR_EN2 = 1;
+
+    NVIC_set_all_irq_priorities(3);
+    NVIC_SetPriority(SPI0_IRQn, 0x0);     // Wi-Fi SPI interrupt must be higher priority than SysTick
+    NVIC_SetPriority(PORTA_IRQn, 0x1);
+    NVIC_SetPriority(SysTick_IRQn, 0x2);  // SysTick set to lower priority than Wi-Fi SPI bus interrupt
+    PORTA->PCR[16] |=PORT_PCR_ISF_MASK;
+    PORTA->ISFR |= (1 << 16);
+}
+
+#elif (MY_BOARD == WIFI_DIPCORTEX)
+
+/**
+ *  \brief Wifi DipCortex initialization
+ *  \param none
+ *  \return none
+ */
+void init() {
+    NVIC_SetPriority(SSP1_IRQn, 0x0);
+    NVIC_SetPriority(PIN_INT0_IRQn, 0x1);
+
+    // SysTick set to lower priority than Wi-Fi SPI bus interrupt
+    NVIC_SetPriority(SysTick_IRQn, 0x2);
+}
+
+#else
+
+/**
+ *  \brief Place here init routine for your board
+ *  \param none
+ *  \return none
+ */
+void init() {
+
+}
+
+#endif