File content as of revision 25:21dcd3f9eac2:

#include "mbed.h"
#include "QEI.h"
#include "HIDScope.h"
#include "Biquad.h"
#include "controlandadjust.h"
#include "angleandposition.h"

///////////////////////////////////////////////info out
HIDScope scope(6);// number of hidscope channels
const double scope_frequency=500; //HIDscope frequency
Timer checktimer;
volatile double checktimervalue=0;

Serial pc(USBTX,USBRX);// serial connection to pc

DigitalOut ledred(LED_RED);
DigitalOut ledgreen(LED_GREEN);
DigitalOut ledblue(LED_BLUE);

Ticker scope_ticker;
/////////////////////////////////////////////ENCODERS
const float cpr_sensor=32;
const float cpr_shaft=cpr_sensor*131;//counts per rotation of the sensor

QEI encoder1(D13,D12,NC,cpr_sensor);/// encoders on motors X2 encoding
QEI encoder2(D10,D11,NC,cpr_sensor);

const double PIE=3.14159265359;
const float counttorad=((2*PIE)/cpr_shaft);// counts per rotation of the shaft


/////////////////////////////////CALIBRATION (MODE)
const double radpersec_calibrate=0.1*PIE;// speed of arms when in calibration mode
int modecounter=1;//counter in which mode the robot is
const double readbuttoncalibrate_frequency=10;//frequency at which the buttons are read when in calibration mode
const double ledblink_frequency=4;//frequency at which the green led and leds on top blink when in resp button or calibration mode

DigitalIn changemodebutton(PTA4);// button to change mode (sw3)
Ticker readbuttoncalibrate_ticker;
Ticker ledblink_ticker;

DigitalIn buttonR(D2);//rigth button on biorobotics shield
DigitalIn buttonL(D3);//left button on biorobotics shield

//////////////////////////////////CONTROLLER
const double control_frequency=250;// frequency at which the controller is called
//controller constants
float Kp=1;
float Ki=0.1;
float Kd=0.001;
controlandadjust mycontroller(6); // make a controller, value in brackets is errorband

Ticker control_ticker;

const double Ts_control=1.0/control_frequency;

float error1=0;
float error2=0;
float error1_int=0;// storage variables for the errors
float error2_int=0;
float error1_prev=0;
float error2_prev=0;

InterruptIn valuechangebutton(PTC6);//button to change controller constants

//safetyandthreshold
AnalogIn safety_pot(A3);//pot 2, used for the safety cutoff value for the pwm
AnalogIn threshold_pot(A2);//pot1, used to adjust threshold if signal differs per person

Ticker safetyandthreshold_ticker; // ticker to read potmeters
const double safetyandthreshold_frequency=1; // frequency for the ticker

float threshold_value=1;//initial threshold value

////////////////////////////////FILTER
const double filter_frequency=500;
#include "filtervalues.h"// call the values for the biquads

Ticker filter_ticker;

Biquad myfilter1;// make filter for signal 1
Biquad myfilter2;//make filter for signal 2

AnalogIn emg1_input(A0);//input for first emg signal
AnalogIn emg2_input(A1);//input for second emg signal

volatile double filteredsignal1=0;//the first filtered emg signal
volatile double filteredsignal2=0;//the second filtered emg signal
float filter_extragain=1;

/////////////////READSIGNAL
const double readsignal_frequency=25;//frequency at wich the filtered emg signal is sampled to be 0 or 1
Ticker readsignal_ticker;


DigitalOut led1(PTC12);// rigth led on biorobotics shield
DigitalOut led2(D9);//left led on biorobotics shield

//////////////////////////////// POSITION AND ANGLE SHIZZLE
const float safetymarginfield=0.075; //adjustable, tweak for maximum but safe range
const float mm_per_sec_emg=0.1;// move the pod 100 mm per sec if muscle is flexed
const float y_start=0.155;//starting y position of the pod
const float y_punch=0.473;// position to where there is punched
const float timetoshoot=0.25;// time it can take to shoot

float desired_position=0;
float desired_angle1=0;
float desired_angle2=0;

const float fieldwidth=0.473;
const float maxdisplacement=((fieldwidth/2)-safetymarginfield); //so the pod doesn't hit the edges of the playfield

angleandposition anglepos;// initiate the angle and position calculation library

const float radtodeg=(180/PIE);



//////////////////////GO FLAGS AND ACTIVATION FUNCTIONS
volatile bool scopedata_go=false,
              control_go=false,
              filter_go=false,
              safetyandthreshold_go=false,
              readsignal_go=false,
              switchedmode=true,
              readbuttoncalibrate_go=false,
              ledblink_go=false;

void scopedata_activate()
{
    scopedata_go=true;
}
void control_activate()
{
    control_go=true;
}
void filter_activate()
{
    filter_go=true;
}
void safetyandthreshold_activate()
{
    safetyandthreshold_go=true;
}
void readsignal_activate()
{
    readsignal_go=true;
}
void readbuttoncalibrate_activate()
{
    readbuttoncalibrate_go=true;
}
void ledblink_activate()
{
    ledblink_go=true;
}

////////////////////////FUNCTIONS
//gather data and send to scope
void scopedata()
{
    scope.set(0,desired_position);
    scope.set(1,desired_angle1*radtodeg);
    scope.set(2,desired_angle2*radtodeg);
    scope.set(3,error1*radtodeg);
    scope.set(4,error2*radtodeg);
    scope.set(5,checktimervalue);
    scope.send();
}
//read potmeters and adjust the safetyfactor and threshold
void safetyandthreshold()
{
    mycontroller.cutoff((ceil (10*safety_pot.read()) )/10); // adjust the safetyfactor value between 0 and 1 rounded to 1 decimal
    threshold_value=((ceil (10*threshold_pot.read()) )/10); // adjust the threshold value between 0 and 1 rounded to 1 decimal
}
/////filter
void filtereverything()
{
    //pass1 so f1
    double pass1_emg1 = myfilter1.filter(emg1_input.read(), v1_f1_emg1 , v2_f1_emg1 , a1_f1 , a2_f1 , b0_f1 , b1_f1 , b2_f1);
    double pass1_emg2 = myfilter2.filter(emg2_input.read(), v1_f1_emg2 , v2_f1_emg2 , a1_f1 , a2_f1 , b0_f1 , b1_f1 , b2_f1);

    //pass2 so f2
    double pass2_emg1 = myfilter1.filter(pass1_emg1, v1_f2_emg1 , v2_f2_emg1 , a1_f2 , a2_f2 , b0_f2 , b1_f2 , b2_f2);
    double pass2_emg2 = myfilter2.filter(pass1_emg2, v1_f2_emg2 , v2_f2_emg2 , a1_f2 , a2_f2 , b0_f2 , b1_f2 , b2_f2);

    //pass3 so f3
    double pass3_emg1 = myfilter1.filter(pass2_emg1, v1_f3_emg1 , v2_f3_emg1 , a1_f3 , a2_f3 , b0_f3 , b1_f3 , b2_f3);
    double pass3_emg2 = myfilter2.filter(pass2_emg2, v1_f3_emg2 , v2_f3_emg2 , a1_f3 , a2_f3 , b0_f3 , b1_f3 , b2_f3);

    //pass4 so f4
    double pass4_emg1 = myfilter1.filter(pass3_emg1, v1_f4_emg1 , v2_f4_emg1 , a1_f4 , a2_f4 , b0_f4 , b1_f4 , b2_f4);
    double pass4_emg2 = myfilter2.filter(pass3_emg2, v1_f4_emg2 , v2_f4_emg2 , a1_f4 , a2_f4 , b0_f4 , b1_f4 , b2_f4);

    //pass5 so f5
    double pass5_emg1 = myfilter1.filter(pass4_emg1, v1_f5_emg1 , v2_f5_emg1 , a1_f5 , a2_f5 , b0_f5 , b1_f5 , b2_f5);
    double pass5_emg2 = myfilter2.filter(pass4_emg2, v1_f5_emg2 , v2_f5_emg2 , a1_f5 , a2_f5 , b0_f5 , b1_f5 , b2_f5);

    ///// take absolute value
    double pass5_emg1_abs=(fabs(pass5_emg1));
    double pass5_emg2_abs=(fabs(pass5_emg2));

    //pass6 so f6
    double pass6_emg1 = myfilter1.filter(pass5_emg1_abs, v1_f6_emg1 , v2_f6_emg1 , a1_f6 , a2_f6 , b0_f6 , b1_f6 , b2_f6);
    double pass6_emg2 = myfilter2.filter(pass5_emg2_abs, v1_f6_emg2 , v2_f6_emg2 , a1_f6 , a2_f6 , b0_f6 , b1_f6 , b2_f6);


    //pass7 so f7
    double pass7_emg1 = myfilter1.filter(pass6_emg1, v1_f7_emg1 , v2_f7_emg1 , a1_f7 , a2_f7 , b0_f7 , b1_f7 , b2_f7);
    double pass7_emg2 = myfilter2.filter(pass6_emg2, v1_f7_emg2 , v2_f7_emg2 , a1_f7 , a2_f7 , b0_f7 , b1_f7 , b2_f7);

    filteredsignal1=(pass7_emg1*9e11*filter_extragain);
    filteredsignal2=(pass7_emg2*9e11*filter_extragain);
}

//adjust controller values when sw2 is pressed
void valuechange()
{
    mycontroller.STOP();
    pc.printf("KP is now %f, enter new value\n",Kp);
    pc.scanf("%f", &Kp);

    pc.printf("KI is now %f, enter new value\n",Ki);
    pc.scanf("%f", &Ki);

    pc.printf("KD is now %f, enter new value\n",Kd);
    pc.scanf("%f", &Kd);

    pc.printf("Extra gain is now %f, enter new value\n",filter_extragain);
    pc.scanf("%f", &filter_extragain);
}

// shoot the pod forward
void shoot()
{
    ledgreen=1;
    float time=0;
    float stepsize=(y_punch-y_start)/(timetoshoot*control_frequency);
    float y_during_punch=y_start;// set initial y position to start position

    Timer shoottimer;
    shoottimer.reset();
    shoottimer.start();
    //forward
    while (time<=timetoshoot) {
        ledblue=!ledblue;

        y_during_punch+=stepsize; // add stepsize to y position
        if (y_during_punch>=y_punch) {//to check if y position is not bigger than y_punch for safety
            y_during_punch=y_punch;
        } else {
            y_during_punch=y_during_punch;
        }

        desired_angle1=anglepos.positiontoangle1(desired_position,y_during_punch);// calculate desired angles
        desired_angle2=anglepos.positiontoangle2(desired_position,y_during_punch);

        error1=(desired_angle1-counttorad*encoder1.getPulses());//calculate errors
        error2=(desired_angle2-counttorad*encoder2.getPulses());

        mycontroller.PI(error1,error2,Kp,Ki,Ts_control,error1_int,error2_int);// send errors to controller
        scopedata();//send data to hidscope   WARING lower freqyency than normal

        time+=(Ts_control);// add time it should take to calculated time
        wait(time-shoottimer.read());// IMPORTANT wait until the loop has taken the time it should need, if this is not done the loop wil go to fast and the motors can't keep up
    }
    //back
    time=0;
    shoottimer.reset();
    while (time<=timetoshoot) {
        ledblue=!ledblue;

        y_during_punch-=stepsize; // add stepsize to y position
        if (y_during_punch<=y_start) {//to check if y position is not smaller than y_start for safety
            y_during_punch=y_start;
        } else {
            y_during_punch=y_during_punch;
        }

        desired_angle1=anglepos.positiontoangle1(desired_position,y_during_punch);// calculate desired angles
        desired_angle2=anglepos.positiontoangle2(desired_position,y_during_punch);

        error1=(desired_angle1-counttorad*encoder1.getPulses());//calculate errors
        error2=(desired_angle2-counttorad*encoder2.getPulses());

        mycontroller.PI(error1,error2,Kp,Ki,Ts_control,error1_int,error2_int);// send errors to controller
        scopedata();//send data to hidscope   WARING lower freqyency than normal

        time+=(Ts_control);// add time it should take to calculated time
        wait(time-shoottimer.read());// IMPORTANT wait until the loop has taken the time it should need, if this is not done the loop wil go to fast and the motors can't keep up
    }
    shoottimer.stop();
    ledblue=1;
    ledgreen=0;
}

////////////////////////////////////////////////////READ EMG AND MOVE DESIRED POSITION
void readsignal()
{
    //check if pod has to shoot
    if (filteredsignal1>=threshold_value && filteredsignal2>=threshold_value) {
        led1=led2=1;
        shoot();
        // check if pod has to move to the right
    } else if (filteredsignal1>=threshold_value && filteredsignal2<=threshold_value) {
        led1=1;
        led2=0;
        desired_position += (mm_per_sec_emg/readsignal_frequency);// move desiredposition right
        if (desired_position>=maxdisplacement) {//check if the pod doesnt move too far and hit the edge
            desired_position=maxdisplacement;
        } else {
            desired_position=desired_position;
        }
        // check if pod has to move to the left
    } else if (filteredsignal1<=threshold_value && filteredsignal2>=threshold_value) {
        led1=0;
        led2=1;
        desired_position -= (mm_per_sec_emg/readsignal_frequency);//move desiredposition left
        if (desired_position<=(-1*maxdisplacement)) {//check if the pod doesnt move too far and hit the edge
            desired_position=(-1*maxdisplacement);
        } else {
            desired_position=desired_position;
        }
    } else {
        led1=led2=0;
    }
}
///////////////////////////////////////////////READ BUTTON AND MOVE DESIRED POSITION
void readsignalbutton()
{
    //write value of button to variable
    int buttonr=buttonR.read();
    int buttonl=buttonL.read();
    //check if pod has to shoot
    if (buttonr==0 && buttonl==0) {
        led1=led2=1;
        shoot();
        // check if pod has to move to the right
    } else if (buttonr==0 && buttonl==1) {
        led1=1;
        led2=0;
        desired_position += (mm_per_sec_emg/readsignal_frequency);// move desiredposition right
        if (desired_position>=maxdisplacement) {//check if the pod doesnt move too far and hit the edge
            desired_position=maxdisplacement;
        } else {
            desired_position=desired_position;
        }
        // check if pod has to move to the left
    } else if (buttonr==1 && buttonl==0) {
        led1=0;
        led2=1;
        desired_position -= (mm_per_sec_emg/readsignal_frequency);//move desiredposition left
        if (desired_position<=(-1*maxdisplacement)) {//check if the pod doesnt move too far and hit the edge
            desired_position=(-1*maxdisplacement);
        } else {
            desired_position=desired_position;
        }
    } else {
        led1=led2=0;
    }
}

void changemode()//this makes the counter higher to switch between modes
{
    mycontroller.STOP();
    switchedmode=true;
    modecounter++;
    if (modecounter==4) {
        modecounter=0;
    } else {
        modecounter=modecounter;
    }
    wait(1);// needed because else it is checked too fast if the button is pressed and modes change too fast
    // tried it with interruptin but dinn't work
}

///////////////////////////////////////////////////MAIN

int main()
{
    //tickers
    safetyandthreshold_ticker.attach(&safetyandthreshold_activate,1.0/safetyandthreshold_frequency);
    filter_ticker.attach(&filter_activate,1.0/filter_frequency);
    control_ticker.attach(&control_activate,1.0/control_frequency);
    scope_ticker.attach(&scopedata_activate,1.0/scope_frequency);
    readsignal_ticker.attach(&readsignal_activate, 1.0/readsignal_frequency);
    readbuttoncalibrate_ticker.attach(&readbuttoncalibrate_activate, 1.0/readbuttoncalibrate_frequency);
    ledblink_ticker.attach(&ledblink_activate, 1.0/ledblink_frequency);

    pc.baud(115200);//set baudrate to 115200
    while(1) {
        checktimer.reset();
       checktimer.start();
        if (changemodebutton==0) {// check if the change mode button is pressed
            changemode();
        }
        if (scopedata_go==true) {//send scopedata
        //TIME THIS LOOP TAKES 0.000008 SEC (PEAKS AT 0.000015)
            scopedata();
            scopedata_go=false;             
        }
        if (safetyandthreshold_go==true) {// check the potmeters
        //TIME THIS LOOP TAKES: 0.000032 SEC          
            safetyandthreshold();
            safetyandthreshold_go=false;
                    }
        ///////////////////////////////////////////NORMAL RUNNING MODE
        if(modecounter==0) {
            if (switchedmode==true) {
                encoder1.reset();// reset encoders so they are at 0 degrees
                encoder2.reset();
                pc.printf("Program running\n");//
                ledgreen=0;
                led1=led2=ledred=ledblue=1;
                switchedmode=false;
            }
            if (filter_go==true) {// filter the emg signal
            // TIME THIS LOOP TAKES: 0.000173 SEC           
                filtereverything();
                filter_go=false;                
            }
            if (readsignal_go==true) {// check if signal is 0 or 1 and adjust wanted position
            // TIME THIS LOOP TAKES: 0.000005 SEC
                readsignal();
                readsignal_go=false;
                           }
            if (control_go==true) {// calculate angles from positions and send error to controller
            //TIME THIS LOOP TAKES: 0.000223 SEC
            
                desired_angle1=anglepos.positiontoangle1(desired_position,y_start);
                desired_angle2=anglepos.positiontoangle2(desired_position,y_start);

                float error1=(desired_angle1-counttorad*encoder1.getPulses());
                float error2=(desired_angle2-counttorad*encoder2.getPulses());
                mycontroller.PI(error1,error2,Kp,Ki,Ts_control,error1_int,error2_int);
                control_go=false;
                            }
            valuechangebutton.fall(&valuechange);// used to change controller variables and the gain for the filter
        }
        ////////////////////////////////////////////////////CALIBRATE RIGHT ARM
        if (modecounter==1) {
            if(switchedmode==true) {
                pc.printf("Calibration mode! Use buttons to move rigth arm to 0 degrees\n");
                led1=led2=ledred=0;
                ledgreen=ledblue=1;
                switchedmode=false;
            }
            if (ledblink_go==true) {
                led1=!led1;// blink rigth led on biorobotics shield (because rigth arm is being calibrated)
                ledblink_go=false;
            }
            if (readbuttoncalibrate_go==true) {//check wich button is pressed and adjust wanted angle of rigth arm
                if (buttonR.read()==0 && buttonL.read()==1) {
                    desired_angle1 += (radpersec_calibrate/readbuttoncalibrate_frequency);
                    readbuttoncalibrate_go=false;
                }
                if (buttonR.read()==1 && buttonL.read()==0) {
                    desired_angle1 -= (radpersec_calibrate/readbuttoncalibrate_frequency);
                    readbuttoncalibrate_go=false;
                }
            }
            if (control_go==true) {// calculate errors and send them to controllers
                error1=(desired_angle1-counttorad*encoder1.getPulses());
                error2=0;
                mycontroller.PI(error1,error2,Kp,Ki,Ts_control,error1_int,error2_int);
                control_go=false;
            }
        }
        ////////////////////////////////////////////CALIBRATE LEFT ARM
        if (modecounter==2) {
            if(switchedmode==true) {
                pc.printf("Calibration mode! Use buttons to move left arm to 0 degrees\n");
                led1=led2=ledred=0;
                ledgreen=ledblue=1;
                switchedmode=false;
            }
            if (ledblink_go==true) {
                led2=!led2;// blink left led on biorobotics shield (because left arm is being calibrated)
                ledblink_go=false;
            }
            if (readbuttoncalibrate_go==true) {//
                if (buttonR.read()==0 && buttonL.read()==1) {//check wich button is pressed and adjust wanted angle of left arm
                    desired_angle2 += (radpersec_calibrate/readbuttoncalibrate_frequency);
                    readbuttoncalibrate_go=false;
                }
                if (buttonR.read()==1 && buttonL.read()==0) {
                    desired_angle2 -= (radpersec_calibrate/readbuttoncalibrate_frequency);
                    readbuttoncalibrate_go=false;
                }
            }
            if (control_go==true) {// calculate errors and send to controller
                error1=0;
                error2=(desired_angle2-counttorad*encoder2.getPulses());
                mycontroller.PI(error1,error2,Kp,Ki,Ts_control,error1_int,error2_int);
                control_go=false;
            }
        }
        ///////////////////////////////BUTTONCONTROLMODE
        if (modecounter==3) {
            if (switchedmode==true) {
                pc.printf("Buttonmode, you can use the buttons to control the robot\n");
                led1=led2=0;
                ledred=ledblue=1;
                encoder1.reset();// reset encoders so they are at 0 degrees
                encoder2.reset();
                switchedmode=false;
            }
            if (ledblink_go==true) {
                ledgreen=!ledgreen;
                ledblink_go=false;
            }
            if (readsignal_go==true) {// read buttons and adjus wanted position
                readsignalbutton();
                readsignal_go=false;
            }
            if (control_go==true) {// calculate wanted angles from position, errors and send to controller
                desired_angle1=anglepos.positiontoangle1(desired_position,y_start);
                desired_angle2=anglepos.positiontoangle2(desired_position,y_start);

                error1=(desired_angle1-counttorad*encoder1.getPulses());
                error2=(desired_angle2-counttorad*encoder2.getPulses());
                mycontroller.PI(error1,error2,Kp,Ki,Ts_control,error1_int,error2_int);
                control_go=false;
            }
            valuechangebutton.fall(&valuechange);// used to change controller variables and the gain for the filter
        }
        checktimervalue=checktimer.read();
        checktimer.stop();
    }
}