Nanostack Border Router is a generic mbed border router implementation that provides the 6LoWPAN ND or Thread border router initialization logic.

4 weeks ago

File content as of revision 95:930ccc91b349:

# Nanostack Border Router

Nanostack Border Router is a generic mbed border router implementation that provides the 6LoWPAN ND, Thread or Wi-SUN border router initialization logic.

Note: Wi-SUN is currently available for partners only.

Border router is a network gateway between a wireless 6LoWPAN mesh network and a backhaul network. It controls and relays traffic between the two networks. In a typical setup, a 6LoWPAN border router is connected to another router in the backhaul network (over Ethernet or a serial line) which in turn forwards traffic to/from the internet or a private company LAN, for instance.


## Structure

This application runs on mbed OS and utilizes PHY drivers and Nanostack to form a border router.


The code layout is organized like this:

configs/                  Contains example configuration files
drivers/                  Contains PHY drivers
mbed-os/                  Contains mbed OS itself
source/                   Contains the application code
mbed_app.json             Build time configuration file

## Building

1. Clone this repository.
1. Run `mbed deploy`.
1. Add connectivity driver, if not provided by Mbed OS
1. Select target platform.
1. Select toolchain.
1. Configure.
1. Build.

For example:

$ mbed deploy

$ mbed target K64F
$ mbed target NUCLEO_F429ZI

$ mbed toolchain GCC_ARM

$ mbed compile

### Adding connectivity driver

This application requires 802.15.4 RF driver to be provided for the networking stack. Driver can be either external, or provided by the Mbed OS.

External driver can be added by calling

mbed add <driver>
For example STM Spirit1 RF driver is added by calling `mbed add stm-spirit1-rf-driver`

## Selecting the target platform

The target platform is the hardware on which the border router runs. There are number of target platforms already available for you in the mbed OS.

If you wish to write your own target, follow the instructions in [Adding target support to mbed OS 5](

The border router requires an RF driver to be provided for Nanostack. Currently, there are the following drivers available in the Mbed OS:

* [Atmel AT86RF233](
* [Atmel AT86RF212B](
* [NXP MCR20A](
* [STM-s2lp](

Following external driver can be added as described [above](#adding-connectivity-driver):

* [STM Spirit1](

The backhaul is either SLIP or Ethernet. For Ethernet either an mbed OS "EMAC"
driver can be used, or a native Nanostack driver. Currently, native Nanostack drivers exists for the following backhauls:

* [K64F Ethernet](
* [SLIP driver](

The existing drivers are found in the `drivers/` folder. More drivers can be linked in.

See [Notes on different hardware]( to see known combinations that work.

## Configuring Nanostack Border Router

Applications using Nanostack Border Router need to use a `.json` file for the configuration. The example configurations can be found in the `configs/` folder.

### The backhaul configuration options

| Field                               | Description                                                   |
| `backhaul-dynamic-bootstrap`          | Defines whether the manually configured backhaul prefix and default route are used, or whether they are learnt automatically via the IPv6 neighbor discovery. False means static and true means automatic configuration. |
| `backhaul-prefix`                     | The IPv6 prefix (64 bits) assigned to and advertised on the backhaul interface. Example format: `fd00:1:2::` |
| `backhaul-default-route`              | The default route (prefix and prefix length) where packets should be forwarded on the backhaul device, default: `::/0`. Example format: `fd00:a1::/10` |
| `backhaul-next-hop`                   | The next-hop value for the backhaul default route; should be a link-local address of a neighboring router, default: empty (on-link prefix). Example format: `fe80::1` |
| `backhaul-mld`                        | Enable sending Multicast Listener Discovery reports to backhaul network when a new multicast listener is registered in mesh network. Values: true or false |

### 6LoWPAN ND border router options

| Field                               | Description                                                   |
| `security-mode`                       | The 6LoWPAN mesh network traffic (link layer) can be protected with the Private Shared Key (PSK) security mode, allowed values: `NONE` and `PSK`. |
| `psk-key`                             | A 16-bytes long private shared key to be used when the security mode is PSK. Example format (hexadecimal byte values separated by commas inside brackets): `{0x00, ..., 0x0f}` |
| `multicast-addr`                      | Multicast forwarding is supported by default. This defines the multicast address to which the border router application forwards multicast packets (on the backhaul and RF interface). Example format: `ff05::5` |
|`ra-router-lifetime`|Defines the router advertisement interval in seconds (default 1024 if left out).|
|`beacon-protocol-id`|Is used to identify beacons. This should not be changed (default 4 if left out).|

To learn more about 6LoWPAN and the configuration parameters, read the [6LoWPAN overview](

See [configs/6lowpan_Atmel_RF.json](configs/6lowpan_Atmel_RF.json) for an example configuration file.

#### The routing protocol RPL (6LoWPAN ND)

Nanostack Border Router uses [RPL]( as the routing protocol on the mesh network side (RF interface) when in 6LoWPAN-ND mode. Currently, only the `grounded/non-storing` operation mode is supported.

Nanostack Border Router offers the following configuration options for RPL:

| Field                               | Description                                                   |
| rpl-instance-id                     | The RPL instance ID value that identifies the RPL instance, default: 1 |
| rpl-idoublings                      | RPL Trickle parameter: DIOIntervalDoublings value, default: 12 |
| rpl-imin                            | RPL Trickle parameter: DIOIntervalMin value, default: 9 |
| rpl-k                               | RPL Trickle parameter: the redundacy constant k, default: 10 |
| rpl-max-rank-inc                    | Maximum rank increase value, default: 2048|
| rpl-min-hop-rank-inc                | Minimum rank increase value, default: 128 |
| rpl-default-lifetime                | Default lifetime for the RPL routes, default: 64 |
| rpl-lifetime-unit                   | The value of the unit that describes the lifetime (in seconds), default: 60 |
| rpl-pcs                             | The number of bits that may be allocated to the path control field. |
| rpl-ocp                             | The Objective Function (OF) to use, values: 1=OF0 (default), 2=MRHOF |

### Thread configuration

The Thread-specific parameters are listed below.

| Field                               | Description                                                   |
| `commissioning-dataset-timestamp`   | Used for updating the Thread network parameters. The device with the highest value propagates the parameters to the network (in the same Realm-Local scope). |
| `pan-id`                            | 2-byte Personal Area Network ID. |
| `extended-pan-id`                   | 8-byte value used to identify Thread networks in range. |
| `mesh-local-prefix`                 | ULA prefix used for communication within the Thread network. |
| `network-name`                      | A human-readable name for the network. |
| `pskc`                              | Pre-Shared Key for the Commissioner. |
| `pskd`                              | Pre-Shared Key for the device. |
| `thread-master-key`                 | A key used to derive security material for MAC and MLE protection. |

### Wi-SUN configuration

The Wi-SUN -specific parameters are listed below.

| Field                               | Description                                                   |
| `network-name`                      | Network name for Wi-SUN the network, MUST be same for all the devices in the network |
| `regulatory-domain`                 | Defines regulatory domain, refer to [ws_management_api]( for correct values for your region. |
| `operating-class`                   | Defines operating class, limited by the regulatory domain |
| `operating-mode`                    | Defines the operating mode, limited by the regulatory domain |
| `uc-channel-function`               | Unicast channel function |
| `bc-channel-function`               | Broadcast channel function |
| `uc-fixed-channel`                  | Fixed channel for unicast |
| `bc-fixed-channel`                  | Fixed channel for broadcast |
| `uc-dwell-interval`                 | Unicast dwell interval. Range: 15-255 milliseconds |
| `bc-interval`                       | Broadcast interval. Duration between broadcast dwell intervals. Range: 0-16777216 milliseconds |
| `bc-dwell-interval`                 | Broadcast dwell interval. Range: 15-255 milliseconds |
| `certificate-header`                | Wi-SUN certificate header file |
| `root-certificate`                  | Root certificate |
| `own-certificate`                   | Own certificate |
| `own-certificate-key`               | Own certificate's key |

Regulatory domain, operating class and operating mode are defined in the Wi-SUN PHY-specification.

For the Thread Border Router, there are example configuration files for `SLIP` and `ETH` backhaul connectivity:

 * [configs/Thread_Atmel_RF.json](configs/Thread_Atmel_RF.json)
 * [configs/Thread_SLIP_Atmel_RF.json](configs/Thread_SLIP_Atmel_RF.json)

The [mbedtls_thread_config.h](source/mbedtls_thread_config.h) file configures mbed TLS for Thread use.

<span class="notes">**Note:** The configuration examples are for testing purposes only; do not use them for production or expose them.</span>

#### Backhaul connectivity

The Nanostack border router application can be connected to a backhaul network. This enables you to connect the devices in a 6LoWPAN mesh network to the internet or a private LAN. Currently, the application supports SLIP (IPv6 encapsulation over a serial line) and Ethernet backhaul connectivity.

"config": {
    "backhaul-driver": {
        "help": "options are ETH, SLIP, EMAC",
        "value": "EMAC"
    "backhaul-mac-src": {
        "help": "Where to get EUI48 address. Options are BOARD, CONFIG",
        "value": "BOARD"
    "backhaul-mac": "{0x02, 0x00, 0x00, 0x00, 0x00, 0x01}",
    "backhaul-dynamic-bootstrap": true,
    "backhaul-prefix": "\"fd00:300::\"",
    "backhaul-next-hop": "\"fe80::1\"",
    "backhaul-default-route": "\"::/0\"",

You can select your preferred option through the configuration file (field `backhaul-driver` in the `config` section). The value `SLIP` includes the SLIP driver, while the value `ETH` compiles the border router application with Nanostack native Ethernet backhaul support. `EMAC` uses the board's default mbed OS network driver, which must be EMAC-based (derived from EMACInterface).

You can define the MAC address on the backhaul interface manually (field `backhaul-mac-src` value `CONFIG`). Alternatively, you can use the MAC address provided by the development board (field `backhaul-mac-src` value `BOARD`). By default, the backhaul driver is set to `EMAC` and the MAC address source is `BOARD`.

You can also set the backhaul bootstrap mode (field `backhaul-dynamic-bootstrap`). By default, the bootstrap mode is set to true, which means the autonomous mode. With the autonomous mode, the border router learns the prefix information automatically from an IPv6 gateway in the Ethernet/SLIP segment. When the parameter is set to false, it enables you to set up a manual configuration of `backhaul-prefix` and `backhaul-default-route`.

If you use the static bootstrap mode, you need to configure a default route on the backhaul interface to properly forward packets between the backhaul and the 6LoWPAN mesh network. In addition to this, you need to set a backhaul prefix. The static mode creates a site-local IPv6 network from which packets cannot be routed outside.

When using the autonomous mode in the 6LoWPAN ND configuration, you can set the `prefix-from-backhaul` option to `true` to use the same backhaul prefix on the mesh network side as well. This allows the mesh nodes to be directly connectable from the outside of the mesh network. In the Thread network, it is enough that `backhaul-dynamic-bootstrap` is set to true.

#### Note on the SLIP backhaul driver

If you are using a K64F board, you need to use the UART1 serial line of the board with the SLIP driver. See the `pins` section in the [mbed_app.json](./mbed_app.json) configuration file. To use a different UART line, replace the `SERIAL_TX` and `SERIAL_RX` values with correct TX/RX pin names.

If you wish to use the hardware flow control, set the configuration field `slip_hw_flow_control` to true. By default, it is set to false. Before using hardware flow control, make sure that the other end of your SLIP interface can handle the flow control.

For the pin names of your desired UART line, refer to your development board's documentation.

An example configuration for the SLIP driver:

"target_overrides": {
    "K64F": {
        "SERIAL_TX": "PTE0",
        "SERIAL_RX": "PTE1",
        "SERIAL_CTS": "PTE2",
        "SERIAL_RTS": "PTE3"

#### Note on EMAC backhaul

When `backhaul_driver` is set to `EMAC`, the border router will use the target's default network driver, as supplied by `NetworkInterface::get_default_instance`. This must be EMAC-based, derived from EMACInterface. If it is the same driver that a default-constructed `EthernetInterface` would use, so in principle it should work on any board where `EthernetInterface` works.

To use a different interface, change the setting of `target.default-network-interface-type` in `mbed_app.json` to point to a different interface type, or add an overriding definition of `NetworkInterface::get_default_instance` to the application - this will override any default supplied by the target board.

To use Wi-Fi or other more complex EMAC drivers, necessary configuration parameters must be supplied, either via `mbed_app.json` or configuration in the `NetworkInterface::get_default_instance` override. Also, the driver must follow the guidelines of `EMACInterface` - the border router does not call the `EMACInterface`'s `connect` method, so the driver must work with only a `powerup` call to the `EMAC`.

### Switching the RF shield

By default, the application uses an Atmel AT86RF233/212B RF driver. You can alternatively use any RF driver provided in the `drivers/` folder or link in your own driver. You can set the configuration for the RF driver in the `json` file.

To select the Atmel radio shield, use the following:

            "help": "options are ATMEL, MCR20, SPIRIT1, S2LP",
            "value": "ATMEL"

To select the NXP radio shield, use the following:

            "help": "options are ATMEL, MCR20, SPIRIT1, S2LP",
            "value": "MCR20"

To select the STM Spirit1 radio shield, use the following:

            "help": "options are ATMEL, MCR20, SPIRIT1, S2LP",
            "value": "SPIRIT1"

To select the STM S2LP radio shield, use the following:
            "help": "options are ATMEL, MCR20, SPIRIT1, S2LP",
            "value": "S2LP"

In case you have choosen the STM Spirit1 Sub-1 GHz RF expansion board [X-NUCLEO-IDS01A4](, you need also to configure its MAC address in the `mbed_app.json` file, for example:

    "target_overrides": {
        "*": {
            "spirit1.mac-address": "{0xf0, 0xf1, 0xf2, 0xf3, 0xf4, 0xf5, 0xf6, 0xf7}"

<span class="notes">**Note**: This MAC address must be unique within the 6LoWPAN mesh network.</span>

After changing the radio shield, you need to recompile the application.

#### Wi-SUN RF shield

Currently there is only one radio shield with a support for Wi-SUN, the STM S2LP radio shield.

## File system support

The Application can enable use of file system as instructed in [mbed OS storage documentation]( File system is not enabled by default due variety of possible configurations.

Thread network stack is able to write/read network configuration settings to/from file system once the feature is activated. Activation happens by telling file system root path to Nanostack. To set the root-path, use function:


Once the root-path is set, Thread stack will read configuration settings from the file system and write configuration back to file system once configuration is changed.

## Running the border router application

1. Find the  binary file `nanostack-border-router.bin` in the `BUILD` folder.
2. Copy the binary to the USB mass storage root of the development board. It is automatically flashed to the target MCU. When the flashing is complete, the board restarts itself. Press the **Reset** button of the development board if it does not restart automatically.
3. The program begins execution.
4. Open the [serial connection](#serial-connection-settings), for example PuTTY.

## Serial connection settings

Serial connection settings for the Nanorouter are as follows:

* Baud-rate = 115200
* Data bits = 8
* Stop bits = 1

If there is no input from the serial terminal, press the **Reset** button of the development board.

In the PuTTY main screen, save the session and click **Open**. This opens a console window showing debug messages from the application. If the console screen is blank, you may need to press the **Reset** button of the board to see the debug information. The serial output from the 6LoWPAN border router looks something like this in the console:

[INFO][app ]: Starting Nanostack border router...
[INFO][app ]: Using ETH backhaul driver...
[INFO][Eth ]: Ethernet cable is connected.
[INFO][addr]: Tentative Address added to IF 1: fe80::ac41:dcff:fe37:72c4
[INFO][addr]: DAD passed on IF 1: fe80::ac41:dcff:fe37:72c4
[INFO][addr]: Tentative Address added to IF 1: 2001:999:21:9ce:ac41:dcff:fe37:72c4
[INFO][addr]: DAD passed on IF 1: 2001:999:21:9ce:ac41:dcff:fe37:72c4
[INFO][brro]: Backhaul bootstrap ready, IPv6 = 2001:999:21:9ce:ac41:dcff:fe37:72c4
[INFO][brro]: Backhaul interface addresses:
[INFO][brro]:    [0] fe80::ac41:dcff:fe37:72c4
[INFO][brro]:    [1] 2001:999:21:9ce:ac41:dcff:fe37:72c4
[INFO][addr]: Address added to IF 0: fe80::ff:fe00:face
[INFO][br  ]: BR nwk base ready for start
[INFO][br  ]: Refresh Contexts
[INFO][br  ]: Refresh Prefixs
[INFO][addr]: Address added to IF 0: 2001:999:21:9ce:0:ff:fe00:face
[INFO][addr]: Address added to IF 0: fe80::fec2:3d00:4:a0cd
[INFO][brro]: RF bootstrap ready, IPv6 = 2001:999:21:9ce:0:ff:fe00:face
[INFO][brro]: RF interface addresses:
[INFO][brro]:    [0] fe80::ff:fe00:face
[INFO][brro]:    [1] fe80::fec2:3d00:4:a0cd
[INFO][brro]:    [2] 2001:999:21:9ce:0:ff:fe00:face
[INFO][brro]: 6LoWPAN Border Router Bootstrap Complete.