A quick example of a simple WiFi application using the WiFi and network-socket APIs that is provided as a part of mbed-os.

The program brings up the WiFi and the underlying network interface, and uses it to scans available networks, connects to a network, prints interface and connection details and performs simple HTTP operation.

Supported hardware:

Not that the mbed target board the WiFi shield gets connected to shouldn't have any other network interface e.g. Ethernet.

ESP8266 is a fallback option and will be used if the build is for unsupported platform.

--- a/README.md	Mon Nov 26 14:00:04 2018 +0000
+++ b/README.md	Mon Dec 17 10:00:03 2018 +0000
@@ -24,7 +24,6 @@
     * [NUCLEO-F401RE](https://os.mbed.com/platforms/ST-Nucleo-F401RE/) with [X-NUCLEO-IDW04A1](http://www.st.com/content/st_com/en/products/ecosystems/stm32-open-development-environment/stm32-nucleo-expansion-boards/stm32-ode-connect-hw/x-nucleo-idw04a1.html) Wi-Fi expansion board using pins D8 and D2 _(of the Arduino connector)_.
     * [NUCLEO-F401RE](https://os.mbed.com/platforms/ST-Nucleo-F401RE/) with [X-NUCLEO-IDW01M1](https://os.mbed.com/components/X-NUCLEO-IDW01M1/) Wi-Fi expansion board using pins PA_9 and PA_10 _(of the Morpho connector)_.
     * [NUCLEO-F429ZI](https://os.mbed.com/platforms/ST-Nucleo-F429ZI/) with ESP8266-01 module using pins D1 and D0.
-    * [NUCLEO-L476RG](https://os.mbed.com/platforms/ST-Nucleo-L476RG/) with ESP8266-01 module using pins D8 and D2.
     * Other Mbed targets with an ESP8266 module, [X-NUCLEO-IDW04A1](http://www.st.com/content/st_com/en/products/ecosystems/stm32-open-development-environment/stm32-nucleo-expansion-boards/stm32-ode-connect-hw/x-nucleo-idw04a1.html) or [X-NUCLEO-IDW01M1](https://os.mbed.com/components/X-NUCLEO-IDW01M1/) expansion board.
 #### Adding connectivity driver
@@ -43,8 +42,6 @@
 To connect the ESP8266 module to your development board, look at the [ESP8266 Cookbook page](https://developer.mbed.org/users/4180_1/notebook/using-the-esp8266-with-the-mbed-lpc1768/). In general, this means hooking up the ESP8266 TX pin to `D0` and the ESP8266 RX pin to `D1` on your development board.
-**Note:** On NUCLEO development boards, pins `D0` and `D1` are used for serial communication with the computer. Use pins `D8` (to ESP8266 TX) and `D2` (to ESP8266 RX) instead.
 #### Connecting the X-NUCLEO-IDW0XX1 ####
 To connect the [X-NUCLEO-IDW04A1](http://www.st.com/content/st_com/en/products/ecosystems/stm32-open-development-environment/stm32-nucleo-expansion-boards/stm32-ode-connect-hw/x-nucleo-idw04a1.html) or [X-NUCLEO-IDW01M1](https://developer.mbed.org/components/X-NUCLEO-IDW01M1/) expansion board to your NUCLEO development board, plug the expansion board on top of the NUCLEO board using the Arduino or Morpho connector.