Prototype RF driver for STM Sub-1 GHz RF expansion board based on the SPSGRF-868 module for STM32 Nucleo.
Prototype RF Driver for STM Sub-1 GHz RF Expansion Boards based on the SPSGRF-868 and SPSGRF-915 Modules for STM32 Nucleo
Currently supported boards:
Note, in order to use expansion board X-NUCLEO-IDS01A4 in mbed you need to perform the following HW modifications on the board:
- Unmount resistor
R4 - Mount resistor
R7
Furthermore, on some Nucleo development boards (e.g. the NUCLEO_F429ZI), in order to be able to use Ethernet together with these Sub-1 GHz RF expansion boards, you need to compile this driver with macro SPIRIT1_SPI_MOSI=PB_5 defined, while the development board typically requires some HW modification as e.g. described here!
This driver can be used together with the 6LoWPAN stack (a.k.a. Nanostack).
source/libs/Contiki_STM32_Library/spirit1-const.h
- Committer:
- Wolfgang Betz
- Date:
- 2017-07-06
- Revision:
- 67:93bec0baf1de
- Parent:
- 34:edda6a7238ec
File content as of revision 67:93bec0baf1de:
/*
* Copyright (c) 2012, STMicroelectronics.
* All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in the
* documentation and/or other materials provided with the distribution.
* 3. Neither the name of the copyright holder nor the names of its
* contributors may be used to endorse or promote products derived
* from this software without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
* ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
* COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
* (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
* SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
* HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
* STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
* ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED
* OF THE POSSIBILITY OF SUCH DAMAGE.
*
*/
/*---------------------------------------------------------------------------*/
#ifndef __SPIRIT1_CONST_H__
#define __SPIRIT1_CONST_H__
/*---------------------------------------------------------------------------*/
/*---------------------------------------------------------------------------*/
/* The state bitfield and values for different states, as read from MC_STATE[1:0] registers,
which are returned on any SPI read or write operation. */
#define SPIRIT1_STATE_STATEBITS (0x00FE)
/*---------------------------------------------------------------------------*/
#define SPIRIT1_STATE_STANDBY ((0x0040)<<1)
#define SPIRIT1_STATE_SLEEP ((0x0036)<<1)
#define SPIRIT1_STATE_READY ((0x0003)<<1)
#define SPIRIT1_STATE_LOCK ((0x000F)<<1)
#define SPIRIT1_STATE_RX ((0x0033)<<1)
#define SPIRIT1_STATE_TX ((0x005F)<<1)
/* NB the below states were extracted from ST drivers, but are not specified in the datasheet */
#define SPIRIT1_STATE_PM_SETUP ((0x003D)<<1)
#define SPIRIT1_STATE_XO_SETTLING ((0x0023)<<1)
#define SPIRIT1_STATE_SYNTH_SETUP ((0x0053)<<1)
#define SPIRIT1_STATE_PROTOCOL ((0x001F)<<1)
#define SPIRIT1_STATE_SYNTH_CALIBRATION ((0x004F)<<1)
/*---------------------------------------------------------------------------*/
/* strobe commands */
#define SPIRIT1_STROBE_TX 0x60
#define SPIRIT1_STROBE_RX 0x61
#define SPIRIT1_STROBE_READY 0x62
#define SPIRIT1_STROBE_STANDBY 0x63
#define SPIRIT1_STROBE_SLEEP 0x64
#define SPIRIT1_STROBE_SABORT 0x67
#define SPIRIT1_STROBE_SRES 0x70
#define SPIRIT1_STROBE_FRX 0x71
#define SPIRIT1_STROBE_FTX 0x72
/*---------------------------------------------------------------------------*/
/* Exported types ------------------------------------------------------------*/
/*------------------------------------------------------------------*/
#endif /* __SPIRIT1_CONST_H__ */
/*---------------------------------------------------------------------------*/
X-NUCLEO-IDS01A4 Sub-1GHz RF Expansion Board