ST
Prototype RF driver for STM Sub-1 GHz RF expansion board based on the SPSGRF-868 module for STM32 Nucleo.
Prototype RF Driver for STM Sub-1 GHz RF Expansion Boards based on the SPSGRF-868 and SPSGRF-915 Modules for STM32 Nucleo
Currently supported boards:
Note, in order to use expansion board X-NUCLEO-IDS01A4 in mbed you need to perform the following HW modifications on the board:
- Unmount resistor
R4 - Mount resistor
R7
Furthermore, on some Nucleo development boards (e.g. the NUCLEO_F429ZI), in order to be able to use Ethernet together with these Sub-1 GHz RF expansion boards, you need to compile this driver with macro SPIRIT1_SPI_MOSI=PB_5 defined, while the development board typically requires some HW modification as e.g. described here!
This driver can be used together with the 6LoWPAN stack (a.k.a. Nanostack).
Diff: libs/spirit1/SPIRIT1_Library/Src/SPIRIT_Radio.c
- Revision:
- 34:edda6a7238ec
- Parent:
- 33:c226804be492
- Child:
- 35:f3f444c379d0
--- a/libs/spirit1/SPIRIT1_Library/Src/SPIRIT_Radio.c Mon Nov 21 13:26:17 2016 +0100
+++ /dev/null Thu Jan 01 00:00:00 1970 +0000
@@ -1,3144 +0,0 @@
-/**
- ******************************************************************************
- * @file SPIRIT_Radio.c
- * @author VMA division - AMS
- * @version 3.2.2
- * @date 08-July-2015
- * @brief This file provides all the low level API to manage Analog and Digital
- * radio part of SPIRIT.
- * @details
- *
- * @attention
- *
- * <h2><center>© COPYRIGHT(c) 2015 STMicroelectronics</center></h2>
- *
- * Redistribution and use in source and binary forms, with or without modification,
- * are permitted provided that the following conditions are met:
- * 1. Redistributions of source code must retain the above copyright notice,
- * this list of conditions and the following disclaimer.
- * 2. Redistributions in binary form must reproduce the above copyright notice,
- * this list of conditions and the following disclaimer in the documentation
- * and/or other materials provided with the distribution.
- * 3. Neither the name of STMicroelectronics nor the names of its contributors
- * may be used to endorse or promote products derived from this software
- * without specific prior written permission.
- *
- * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
- * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
- * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
- * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
- * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
- * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
- * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
- * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
- * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
- * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *
- ******************************************************************************
- */
-
-/* Includes ------------------------------------------------------------------*/
-#include "SPIRIT_Radio.h"
-#include "MCU_Interface.h"
-#include <math.h>
-
-/** @addtogroup SPIRIT_Libraries
-* @{
-*/
-
-
-/** @addtogroup SPIRIT_Radio
-* @{
-*/
-
-
-/** @defgroup Radio_Private_TypesDefinitions Radio Private Types Definitions
-* @{
-*/
-
-
-/**
-* @}
-*/
-
-
-/** @defgroup Radio_Private_Defines Radio Private Defines
-* @{
-*/
-
-
-
-
-/**
-* @}
-*/
-
-
-/** @defgroup Radio_Private_Macros Radio Private Macros
-* @{
-*/
-#define XTAL_FLAG(xtalFrequency) (xtalFrequency>=25e6) ? XTAL_FLAG_26_MHz:XTAL_FLAG_24_MHz
-
-#define ROUND(A) (((A-(uint32_t)A)> 0.5)? (uint32_t)A+1:(uint32_t)A)
-/**
-* @}
-*/
-
-
-/** @defgroup Radio_Private_Variables Radio Private Variables
-* @{
-*/
-/**
-* @brief The Xtal frequency. To be set by the user (see SetXtalFreq() function)
-*/
-static uint32_t s_lXtalFrequency;
-
-/**
-* @brief Factor is: B/2 used in the formula for SYNTH word calculation
-*/
-static const uint8_t s_vectcBHalfFactor[4]={(HIGH_BAND_FACTOR/2), (MIDDLE_BAND_FACTOR/2), (LOW_BAND_FACTOR/2), (VERY_LOW_BAND_FACTOR/2)};
-
-/**
-* @brief BS value to write in the SYNT0 register according to the selected band
-*/
-static const uint8_t s_vectcBandRegValue[4]={SYNT0_BS_6, SYNT0_BS_12, SYNT0_BS_16, SYNT0_BS_32};
-
-
-/**
-* @brief It represents the available channel bandwidth times 10 for 26 Mhz xtal.
-* @note The channel bandwidth for others xtal frequencies can be computed since this table
-* multiplying the current table by a factor xtal_frequency/26e6.
-*/
-static const uint16_t s_vectnBandwidth26M[90]=
-{
- 8001, 7951, 7684, 7368, 7051, 6709, 6423, 5867, 5414, \
- 4509, 4259, 4032, 3808, 3621, 3417, 3254, 2945, 2703, \
- 2247, 2124, 2015, 1900, 1807, 1706, 1624, 1471, 1350, \
- 1123, 1062, 1005, 950, 903, 853, 812, 735, 675, \
- 561, 530, 502, 474, 451, 426, 406, 367, 337, \
- 280, 265, 251, 237, 226, 213, 203, 184, 169, \
- 140, 133, 126, 119, 113, 106, 101, 92, 84, \
- 70, 66, 63, 59, 56, 53, 51, 46, 42, \
- 35, 33, 31, 30, 28, 27, 25, 23, 21, \
- 18, 17, 16, 15, 14, 13, 13, 12, 11
-};
-
-/**
-* @brief It represents the available VCO frequencies
-*/
-static const uint16_t s_vectnVCOFreq[16]=
-{
- 4644, 4708, 4772, 4836, 4902, 4966, 5030, 5095, \
- 5161, 5232, 5303, 5375, 5448, 5519, 5592, 5663
-};
-
-/**
-* @brief This variable is used to enable or disable
-* the VCO calibration WA called at the end of the SpiritRadioSetFrequencyBase fcn.
-* Default is enabled.
-*/
-static SpiritFunctionalState xDoVcoCalibrationWA=S_ENABLE;
-
-
-/**
-* @brief These values are used to interpolate the power curves.
-* Interpolation curves are linear in the following 3 regions:
-* - reg value: 1 to 13 (up region)
-* - reg value: 13 to 40 (mid region)
-* - reg value: 41 to 90 (low region)
-* power_reg = m*power_dBm + q
-* For each band the order is: {m-up, q-up, m-mid, q-mid, m-low, q-low}.
-* @note The power interpolation curves have been extracted
-* by measurements done on the divisional evaluation boards.
-*/
-static const float fPowerFactors[5][6]={
- {-2.11,25.66,-2.11,25.66,-2.00,31.28}, /* 915 */
- {-2.04,23.45,-2.04,23.45,-1.95,27.66}, /* 868 */
- {-3.48,38.45,-1.89,27.66,-1.92,30.23}, /* 433 */
- {-3.27,35.43,-1.80,26.31,-1.89,29.61}, /* 315 */
- {-4.18,50.66,-1.80,30.04,-1.86,32.22}, /* 169 */
-};
-
-/**
-* @}
-*/
-
-
-/** @defgroup Radio_Private_FunctionPrototypes Radio Private Function Prototypes
-* @{
-*/
-
-
-/**
-* @}
-*/
-
-
-/** @defgroup Radio_Private_Functions Radio Private Functions
-* @{
-*/
-
-/**
-* @brief Initializes the SPIRIT analog and digital radio part according to the specified
-* parameters in the pxSRadioInitStruct.
-* @param pxSRadioInitStruct pointer to a SRadioInit structure that
-* contains the configuration information for the analog radio part of SPIRIT.
-* @retval Error code: 0=no error, 1=error during calibration of VCO.
-*/
-uint8_t SpiritRadioInit(SRadioInit* pxSRadioInitStruct)
-{
- int32_t FOffsetTmp;
- uint8_t anaRadioRegArray[8], digRadioRegArray[4];
- int16_t xtalOffsetFactor;
- uint8_t drM, drE, FdevM, FdevE, bwM, bwE;
-
- /* Workaround for Vtune */
- uint8_t value = 0xA0; SpiritSpiWriteRegisters(0x9F, 1, &value);
-
- /* Calculates the offset respect to RF frequency and according to xtal_ppm parameter: (xtal_ppm*FBase)/10^6 */
- FOffsetTmp = (int32_t)(((float)pxSRadioInitStruct->nXtalOffsetPpm*pxSRadioInitStruct->lFrequencyBase)/PPM_FACTOR);
-
- /* Check the parameters */
- s_assert_param(IS_FREQUENCY_BAND(pxSRadioInitStruct->lFrequencyBase));
- s_assert_param(IS_MODULATION_SELECTED(pxSRadioInitStruct->xModulationSelect));
- s_assert_param(IS_DATARATE(pxSRadioInitStruct->lDatarate));
- s_assert_param(IS_FREQUENCY_OFFSET(FOffsetTmp,s_lXtalFrequency));
- s_assert_param(IS_CHANNEL_SPACE(pxSRadioInitStruct->nChannelSpace,s_lXtalFrequency));
- s_assert_param(IS_F_DEV(pxSRadioInitStruct->lFreqDev,s_lXtalFrequency));
-
- /* Disable the digital, ADC, SMPS reference clock divider if fXO>24MHz or fXO<26MHz */
- SpiritSpiCommandStrobes(COMMAND_STANDBY);
- do{
- /* Delay for state transition */
- for(volatile uint8_t i=0; i!=0xFF; i++);
-
- /* Reads the MC_STATUS register */
- SpiritRefreshStatus();
- }while(g_xStatus.MC_STATE!=MC_STATE_STANDBY);
-
- if(s_lXtalFrequency<DOUBLE_XTAL_THR)
- {
- SpiritRadioSetDigDiv(S_DISABLE);
- s_assert_param(IS_CH_BW(pxSRadioInitStruct->lBandwidth,s_lXtalFrequency));
- }
- else
- {
- SpiritRadioSetDigDiv(S_ENABLE);
- s_assert_param(IS_CH_BW(pxSRadioInitStruct->lBandwidth,(s_lXtalFrequency>>1)));
- }
-
- /* Goes in READY state */
- SpiritSpiCommandStrobes(COMMAND_READY);
- do{
- /* Delay for state transition */
- for(volatile uint8_t i=0; i!=0xFF; i++);
-
- /* Reads the MC_STATUS register */
- SpiritRefreshStatus();
- }while(g_xStatus.MC_STATE!=MC_STATE_READY);
-
- /* Calculates the FC_OFFSET parameter and cast as signed int: FOffsetTmp = (Fxtal/2^18)*FC_OFFSET */
- xtalOffsetFactor = (int16_t)(((float)FOffsetTmp*FBASE_DIVIDER)/s_lXtalFrequency);
- anaRadioRegArray[2] = (uint8_t)((((uint16_t)xtalOffsetFactor)>>8)&0x0F);
- anaRadioRegArray[3] = (uint8_t)(xtalOffsetFactor);
-
- /* Calculates the channel space factor */
- anaRadioRegArray[0] =((uint32_t)pxSRadioInitStruct->nChannelSpace<<9)/(s_lXtalFrequency>>6)+1;
-
- SpiritManagementWaTRxFcMem(pxSRadioInitStruct->lFrequencyBase);
-
- /* 2nd order DEM algorithm enabling */
- uint8_t tmpreg; SpiritSpiReadRegisters(0xA3, 1, &tmpreg);
- tmpreg &= ~0x02; SpiritSpiWriteRegisters(0xA3, 1, &tmpreg);
-
- /* Check the channel center frequency is in one of the possible range */
- s_assert_param(IS_FREQUENCY_BAND((pxSRadioInitStruct->lFrequencyBase + ((xtalOffsetFactor*s_lXtalFrequency)/FBASE_DIVIDER) + pxSRadioInitStruct->nChannelSpace * pxSRadioInitStruct->cChannelNumber)));
-
- /* Calculates the datarate mantissa and exponent */
- SpiritRadioSearchDatarateME(pxSRadioInitStruct->lDatarate, &drM, &drE);
- digRadioRegArray[0] = (uint8_t)(drM);
- digRadioRegArray[1] = (uint8_t)(0x00 | pxSRadioInitStruct->xModulationSelect |drE);
-
- /* Read the fdev register to preserve the clock recovery algo bit */
- SpiritSpiReadRegisters(0x1C, 1, &tmpreg);
-
- /* Calculates the frequency deviation mantissa and exponent */
- SpiritRadioSearchFreqDevME(pxSRadioInitStruct->lFreqDev, &FdevM, &FdevE);
- digRadioRegArray[2] = (uint8_t)((FdevE<<4) | (tmpreg&0x08) | FdevM);
-
- /* Calculates the channel filter mantissa and exponent */
- SpiritRadioSearchChannelBwME(pxSRadioInitStruct->lBandwidth, &bwM, &bwE);
-
- digRadioRegArray[3] = (uint8_t)((bwM<<4) | bwE);
-
- float if_off=(3.0*480140)/(s_lXtalFrequency>>12)-64;
-
- uint8_t ifOffsetAna = ROUND(if_off);
-
- if(s_lXtalFrequency<DOUBLE_XTAL_THR)
- {
- /* if offset digital is the same in case of single xtal */
- anaRadioRegArray[1] = ifOffsetAna;
- }
- else
- {
- if_off=(3.0*480140)/(s_lXtalFrequency>>13)-64;
-
- /* ... otherwise recompute it */
- anaRadioRegArray[1] = ROUND(if_off);
- }
-// if(s_lXtalFrequency==24000000) {
-// ifOffsetAna = 0xB6;
-// anaRadioRegArray[1] = 0xB6;
-// }
-// if(s_lXtalFrequency==25000000) {
-// ifOffsetAna = 0xAC;
-// anaRadioRegArray[1] = 0xAC;
-// }
-// if(s_lXtalFrequency==26000000) {
-// ifOffsetAna = 0xA3;
-// anaRadioRegArray[1] = 0xA3;
-// }
-// if(s_lXtalFrequency==48000000) {
-// ifOffsetAna = 0x3B;
-// anaRadioRegArray[1] = 0xB6;
-// }
-// if(s_lXtalFrequency==50000000) {
-// ifOffsetAna = 0x36;
-// anaRadioRegArray[1] = 0xAC;
-// }
-// if(s_lXtalFrequency==52000000) {
-// ifOffsetAna = 0x31;
-// anaRadioRegArray[1] = 0xA3;
-// }
-
- g_xStatus = SpiritSpiWriteRegisters(IF_OFFSET_ANA_BASE, 1, &ifOffsetAna);
-
-
- /* Sets Xtal configuration */
- if(s_lXtalFrequency>DOUBLE_XTAL_THR)
- {
- SpiritRadioSetXtalFlag(XTAL_FLAG((s_lXtalFrequency/2)));
- }
- else
- {
- SpiritRadioSetXtalFlag(XTAL_FLAG(s_lXtalFrequency));
- }
-
- /* Sets the channel number in the corresponding register */
- SpiritSpiWriteRegisters(CHNUM_BASE, 1, &pxSRadioInitStruct->cChannelNumber);
-
- /* Configures the Analog Radio registers */
- SpiritSpiWriteRegisters(CHSPACE_BASE, 4, anaRadioRegArray);
-
- /* Configures the Digital Radio registers */
- g_xStatus = SpiritSpiWriteRegisters(MOD1_BASE, 4, digRadioRegArray);
-
- /* Enable the freeze option of the AFC on the SYNC word */
- SpiritRadioAFCFreezeOnSync(S_ENABLE);
-
- /* Set the IQC correction optimal value */
- anaRadioRegArray[0]=0x80;
- anaRadioRegArray[1]=0xE3;
- g_xStatus = SpiritSpiWriteRegisters(0x99, 2, anaRadioRegArray);
-
- return SpiritRadioSetFrequencyBase(pxSRadioInitStruct->lFrequencyBase);
-
-}
-
-
-/**
-* @brief Returns the SPIRIT analog and digital radio structure according to the registers value.
-* @param pxSRadioInitStruct pointer to a SRadioInit structure that
-* contains the configuration information for the analog radio part of SPIRIT.
-* @retval None.
-*/
-void SpiritRadioGetInfo(SRadioInit* pxSRadioInitStruct)
-{
- uint8_t anaRadioRegArray[8], digRadioRegArray[4];
- BandSelect band;
- int16_t xtalOffsetFactor;
-
- /* Get the RF board version */
- //SpiritVersion xSpiritVersion = SpiritGeneralGetSpiritVersion();
-
- /* Reads the Analog Radio registers */
- SpiritSpiReadRegisters(SYNT3_BASE, 8, anaRadioRegArray);
-
- /* Reads the Digital Radio registers */
- g_xStatus = SpiritSpiReadRegisters(MOD1_BASE, 4, digRadioRegArray);
-
- /* Reads the operating band masking the Band selected field */
- if((anaRadioRegArray[3] & 0x07) == SYNT0_BS_6)
- {
- band = HIGH_BAND;
- }
- else if ((anaRadioRegArray[3] & 0x07) == SYNT0_BS_12)
- {
- band = MIDDLE_BAND;
- }
- else if ((anaRadioRegArray[3] & 0x07) == SYNT0_BS_16)
- {
- band = LOW_BAND;
- }
- else if ((anaRadioRegArray[3] & 0x07) == SYNT0_BS_32)
- {
- band = VERY_LOW_BAND;
- }
- else
- {
- /* if it is another value, set it to a valid one in order to avoid access violation */
- uint8_t tmp=(anaRadioRegArray[3]&0xF8)|SYNT0_BS_6;
- SpiritSpiWriteRegisters(SYNT0_BASE,1,&tmp);
- band = HIGH_BAND;
- }
-
- /* Computes the synth word */
- uint32_t synthWord = (uint32_t)((((uint32_t)(anaRadioRegArray[0]&0x1F))<<21)+(((uint32_t)(anaRadioRegArray[1]))<<13)+\
- (((uint32_t)(anaRadioRegArray[2]))<<5)+(((uint32_t)(anaRadioRegArray[3]))>>3));
-
- /* Calculates the frequency base */
- uint8_t cRefDiv = (uint8_t)SpiritRadioGetRefDiv()+1;
- pxSRadioInitStruct->lFrequencyBase = (uint32_t)round(synthWord*(((double)s_lXtalFrequency)/(FBASE_DIVIDER*cRefDiv*s_vectcBHalfFactor[band])));
-
- /* Calculates the Offset Factor */
- uint16_t xtalOffTemp = ((((uint16_t)anaRadioRegArray[6])<<8)+((uint16_t)anaRadioRegArray[7]));
-
- /* If a negative number then convert the 12 bit 2-complement in a 16 bit number */
- if(xtalOffTemp & 0x0800)
- {
- xtalOffTemp = xtalOffTemp | 0xF000;
- }
- else
- {
- xtalOffTemp = xtalOffTemp & 0x0FFF;
- }
-
- xtalOffsetFactor = *((int16_t*)(&xtalOffTemp));
-
- /* Calculates the frequency offset in ppm */
- pxSRadioInitStruct->nXtalOffsetPpm =(int16_t)((uint32_t)xtalOffsetFactor*s_lXtalFrequency*PPM_FACTOR)/((uint32_t)FBASE_DIVIDER*pxSRadioInitStruct->lFrequencyBase);
-
- /* Channel space */
- pxSRadioInitStruct->nChannelSpace = anaRadioRegArray[4]*(s_lXtalFrequency>>15);
-
- /* Channel number */
- pxSRadioInitStruct->cChannelNumber = SpiritRadioGetChannel();
-
- /* Modulation select */
- pxSRadioInitStruct->xModulationSelect = (ModulationSelect)(digRadioRegArray[1] & 0x70);
-
- /* Reads the frequency deviation for mantissa and exponent */
- uint8_t FDevM = digRadioRegArray[2]&0x07;
- uint8_t FDevE = (digRadioRegArray[2]&0xF0)>>4;
-
- /* Reads the channel filter register for mantissa and exponent */
- uint8_t bwM = (digRadioRegArray[3]&0xF0)>>4;
- uint8_t bwE = digRadioRegArray[3]&0x0F;
-
- uint8_t cDivider = 0;
- cDivider = SpiritRadioGetDigDiv();
-
- /* Calculates the datarate */
- pxSRadioInitStruct->lDatarate = ((s_lXtalFrequency>>(5+cDivider))*(256+digRadioRegArray[0]))>>(23-(digRadioRegArray[1]&0x0F));
-
- /* Calculates the frequency deviation */
- // (((s_lXtalFrequency>>6)*(8+FDevM))>>(12-FDevE+cCorrection));
- pxSRadioInitStruct->lFreqDev =(uint32_t)((float)s_lXtalFrequency/(((uint32_t)1)<<18)*(uint32_t)((8.0+FDevM)/2*(1<<FDevE)));
-
- /* Reads the channel filter bandwidth from the look-up table and return it */
- pxSRadioInitStruct->lBandwidth = (uint32_t)(100.0*s_vectnBandwidth26M[bwM+(bwE*9)]*((s_lXtalFrequency>>cDivider)/26e6));
-
-}
-
-
-/**
-* @brief Sets the Xtal configuration in the ANA_FUNC_CONF0 register.
-* @param xXtal one of the possible value of the enum type XtalFrequency.
-* @arg XTAL_FLAG_24_MHz: in case of 24 MHz crystal
-* @arg XTAL_FLAG_26_MHz: in case of 26 MHz crystal
-* @retval None.
-*/
-void SpiritRadioSetXtalFlag(XtalFlag xXtal)
-{
- uint8_t tempRegValue = 0x00;
-
- /* Check the parameters */
- s_assert_param(IS_XTAL_FLAG(xXtal));
-
- /* Reads the ANA_FUNC_CONF_0 register */
- g_xStatus = SpiritSpiReadRegisters(ANA_FUNC_CONF0_BASE, 1, &tempRegValue);
- if(xXtal == XTAL_FLAG_26_MHz)
- {
- tempRegValue|=SELECT_24_26_MHZ_MASK;
- }
- else
- {
- tempRegValue &= (~SELECT_24_26_MHZ_MASK);
- }
-
- /* Sets the 24_26MHz_SELECT field in the ANA_FUNC_CONF_0 register */
- g_xStatus = SpiritSpiWriteRegisters(ANA_FUNC_CONF0_BASE, 1, &tempRegValue);
-
-}
-
-
-/**
-* @brief Returns the Xtal configuration in the ANA_FUNC_CONF0 register.
-* @param None.
-* @retval XtalFrequency Settled Xtal configuration.
-*/
-XtalFlag SpiritRadioGetXtalFlag(void)
-{
- uint8_t tempRegValue;
-
- /* Reads the Xtal configuration in the ANA_FUNC_CONF_0 register and return the value */
- g_xStatus = SpiritSpiReadRegisters(ANA_FUNC_CONF0_BASE, 1, &tempRegValue);
-
- return (XtalFlag)((tempRegValue & 0x40)>>6);
-
-}
-
-
-/**
-* @brief Returns the charge pump word for a given VCO frequency.
-* @param lFc channel center frequency expressed in Hz.
-* This parameter can be a value in one of the following ranges:<ul>
-* <li> High_Band: from 779 MHz to 915 MHz </li>
-* <li> Middle Band: from 387 MHz to 470 MHz </li>
-* <li> Low Band: from 300 MHz to 348 MHz </li>
-* <li> Very low Band: from 150 MHz to 174 MHz </li> </ul>
-* @retval uint8_t Charge pump word.
-*/
-uint8_t SpiritRadioSearchWCP(uint32_t lFc)
-{
- int8_t i;
- uint32_t vcofreq;
- uint8_t BFactor;
-
- /* Check the channel center frequency is in one of the possible range */
- s_assert_param(IS_FREQUENCY_BAND(lFc));
-
- /* Search the operating band */
- if(IS_FREQUENCY_BAND_HIGH(lFc))
- {
- BFactor = HIGH_BAND_FACTOR;
- }
- else if(IS_FREQUENCY_BAND_MIDDLE(lFc))
- {
- BFactor = MIDDLE_BAND_FACTOR;
- }
- else if(IS_FREQUENCY_BAND_LOW(lFc))
- {
- BFactor = LOW_BAND_FACTOR;
- }
- else
- {
- BFactor = VERY_LOW_BAND_FACTOR;
- }
-
- /* Calculates the VCO frequency VCOFreq = lFc*B */
- vcofreq = (lFc/1000000)*BFactor;
-
- /* Search in the vco frequency array the charge pump word */
- if(vcofreq>=s_vectnVCOFreq[15])
- {
- i=15;
- }
- else
- {
- /* Search the value */
- for(i=0 ; i<15 && vcofreq>s_vectnVCOFreq[i] ; i++);
-
- /* Be sure that it is the best approssimation */
- if (i!=0 && s_vectnVCOFreq[i]-vcofreq>vcofreq-s_vectnVCOFreq[i-1])
- i--;
- }
-
- /* Return index */
- return (i%8);
-
-}
-
-/**
-* @brief Returns the synth word.
-* @param None.
-* @retval uint32_t Synth word.
-*/
-uint32_t SpiritRadioGetSynthWord(void)
-{
- uint8_t regArray[4];
-
- /* Reads the SYNTH registers, build the synth word and return it */
- g_xStatus = SpiritSpiReadRegisters(SYNT3_BASE, 4, regArray);
- return ((((uint32_t)(regArray[0]&0x1F))<<21)+(((uint32_t)(regArray[1]))<<13)+\
- (((uint32_t)(regArray[2]))<<5)+(((uint32_t)(regArray[3]))>>3));
-
-}
-
-
-/**
-* @brief Sets the SYNTH registers.
-* @param lSynthWord the synth word to write in the SYNTH[3:0] registers.
-* @retval None.
-*/
-void SpiritRadioSetSynthWord(uint32_t lSynthWord)
-{
- uint8_t tempArray[4];
- uint8_t tempRegValue;
-
- /* Reads the SYNT0 register */
- g_xStatus = SpiritSpiReadRegisters(SYNT0_BASE, 1, &tempRegValue);
-
- /* Mask the Band selected field */
- tempRegValue &= 0x07;
-
- /* Build the array for SYNTH registers */
- tempArray[0] = (uint8_t)((lSynthWord>>21)&(0x0000001F));
- tempArray[1] = (uint8_t)((lSynthWord>>13)&(0x000000FF));
- tempArray[2] = (uint8_t)((lSynthWord>>5)&(0x000000FF));
- tempArray[3] = (uint8_t)(((lSynthWord&0x0000001F)<<3)| tempRegValue);
-
- /* Writes the synth word in the SYNTH registers */
- g_xStatus = SpiritSpiWriteRegisters(SYNT3_BASE, 4, tempArray);
-
-}
-
-
-/**
-* @brief Sets the operating band.
-* @param xBand the band to set.
-* This parameter can be one of following parameters:
-* @arg HIGH_BAND High_Band selected: from 779 MHz to 915 MHz
-* @arg MIDDLE_BAND: Middle Band selected: from 387 MHz to 470 MHz
-* @arg LOW_BAND: Low Band selected: from 300 MHz to 348 MHz
-* @arg VERY_LOW_BAND: Very low Band selected: from 150 MHz to 174 MHz
-* @retval None.
-*/
-void SpiritRadioSetBand(BandSelect xBand)
-{
- uint8_t tempRegValue;
-
- /* Check the parameters */
- s_assert_param(IS_BAND_SELECTED(xBand));
-
- /* Reads the SYNT0 register*/
- g_xStatus = SpiritSpiReadRegisters(SYNT0_BASE, 1, &tempRegValue);
-
- /* Mask the SYNTH[4;0] field and write the BS value */
- tempRegValue &= 0xF8;
- tempRegValue |= s_vectcBandRegValue[xBand];
-
- /* Configures the SYNT0 register setting the operating band */
- g_xStatus = SpiritSpiWriteRegisters(SYNT0_BASE, 1, &tempRegValue);
-
-}
-
-
-/**
-* @brief Returns the operating band.
-* @param None.
-* @retval BandSelect Settled band.
-* This returned value can be one of the following parameters:
-* @arg HIGH_BAND High_Band selected: from 779 MHz to 915 MHz
-* @arg MIDDLE_BAND: Middle Band selected: from 387 MHz to 470 MHz
-* @arg LOW_BAND: Low Band selected: from 300 MHz to 348 MHz
-* @arg VERY_LOW_BAND: Very low Band selected: from 150 MHz to 174 MHz
-*/
-BandSelect SpiritRadioGetBand(void)
-{
- uint8_t tempRegValue;
-
- /* Reads the SYNT0 register */
- g_xStatus = SpiritSpiReadRegisters(SYNT0_BASE, 1, &tempRegValue);
-
- /* Mask the Band selected field */
- if((tempRegValue & 0x07) == SYNT0_BS_6)
- {
- return HIGH_BAND;
- }
- else if ((tempRegValue & 0x07) == SYNT0_BS_12)
- {
- return MIDDLE_BAND;
- }
- else if ((tempRegValue & 0x07) == SYNT0_BS_16)
- {
- return LOW_BAND;
- }
- else
- {
- return VERY_LOW_BAND;
- }
-
-}
-
-
-/**
-* @brief Sets the channel number.
-* @param cChannel the channel number.
-* @retval None.
-*/
-void SpiritRadioSetChannel(uint8_t cChannel)
-{
- /* Writes the CHNUM register */
- g_xStatus = SpiritSpiWriteRegisters(CHNUM_BASE, 1, &cChannel);
-
-}
-
-
-/**
-* @brief Returns the actual channel number.
-* @param None.
-* @retval uint8_t Actual channel number.
-*/
-uint8_t SpiritRadioGetChannel(void)
-{
- uint8_t tempRegValue;
-
- /* Reads the CHNUM register and return the value */
- g_xStatus = SpiritSpiReadRegisters(CHNUM_BASE, 1, &tempRegValue);
-
- return tempRegValue;
-
-}
-
-
-/**
-* @brief Sets the channel space factor in channel space register.
-* The channel spacing step is computed as F_Xo/32768.
-* @param fChannelSpace the channel space expressed in Hz.
-* @retval None.
-*/
-void SpiritRadioSetChannelSpace(uint32_t fChannelSpace)
-{
- uint8_t cChannelSpaceFactor;
-
- /* Round to the nearest integer */
- cChannelSpaceFactor = ((uint32_t)fChannelSpace*CHSPACE_DIVIDER)/s_lXtalFrequency;
-
- /* Write value into the register */
- g_xStatus = SpiritSpiWriteRegisters(CHSPACE_BASE, 1, &cChannelSpaceFactor);
-
-}
-
-
-/**
-* @brief Returns the channel space register.
-* @param None.
-* @retval uint32_t Channel space. The channel space is: CS = channel_space_factor x XtalFrequency/2^15
-* where channel_space_factor is the CHSPACE register value.
-*/
-uint32_t SpiritRadioGetChannelSpace(void)
-{
- uint8_t channelSpaceFactor;
-
- /* Reads the CHSPACE register, calculate the channel space and return it */
- g_xStatus = SpiritSpiReadRegisters(CHSPACE_BASE, 1, &channelSpaceFactor);
-
- /* Compute the Hertz value and return it */
- return ((channelSpaceFactor*s_lXtalFrequency)/CHSPACE_DIVIDER);
-
-}
-
-
-/**
-* @brief Sets the FC OFFSET register starting from xtal ppm value.
-* @param nXtalPpm the xtal offset expressed in ppm.
-* @retval None.
-*/
-void SpiritRadioSetFrequencyOffsetPpm(int16_t nXtalPpm)
-{
- uint8_t tempArray[2];
- int16_t xtalOffsetFactor;
- uint32_t synthWord, fBase;
- int32_t FOffsetTmp;
- BandSelect band;
-
- /* Reads the synth word */
- synthWord = SpiritRadioGetSynthWord();
-
- /* Reads the operating band */
- band = SpiritRadioGetBand();
-
- /* Calculates the frequency base */
- uint8_t cRefDiv = (uint8_t)SpiritRadioGetRefDiv()+1;
- fBase = synthWord*(s_lXtalFrequency/(s_vectcBHalfFactor[band]*cRefDiv)/FBASE_DIVIDER);
-
- /* Calculates the offset respect to RF frequency and according to xtal_ppm parameter */
- FOffsetTmp = (int32_t)(((float)nXtalPpm*fBase)/PPM_FACTOR);
-
- /* Check the Offset is in the correct range */
- s_assert_param(IS_FREQUENCY_OFFSET(FOffsetTmp,s_lXtalFrequency));
-
- /* Calculates the FC_OFFSET value to write in the corresponding register */
- xtalOffsetFactor = (int16_t)(((float)FOffsetTmp*FBASE_DIVIDER)/s_lXtalFrequency);
-
- /* Build the array related to the FC_OFFSET_1 and FC_OFFSET_0 register */
- tempArray[0]=(uint8_t)((((uint16_t)xtalOffsetFactor)>>8)&0x0F);
- tempArray[1]=(uint8_t)(xtalOffsetFactor);
-
- /* Writes the FC_OFFSET registers */
- g_xStatus = SpiritSpiWriteRegisters(FC_OFFSET1_BASE, 2, tempArray);
-
-}
-
-
-/**
-* @brief Sets the FC OFFSET register starting from frequency offset expressed in Hz.
-* @param lFOffset frequency offset expressed in Hz as signed word.
-* @retval None.
-*/
-void SpiritRadioSetFrequencyOffset(int32_t lFOffset)
-{
- uint8_t tempArray[2];
- int16_t offset;
-
- /* Check that the Offset is in the correct range */
- s_assert_param(IS_FREQUENCY_OFFSET(lFOffset,s_lXtalFrequency));
-
- /* Calculates the offset value to write in the FC_OFFSET register */
- offset = (int16_t)(((float)lFOffset*FBASE_DIVIDER)/s_lXtalFrequency);
-
- /* Build the array related to the FC_OFFSET_1 and FC_OFFSET_0 register */
- tempArray[0]=(uint8_t)((((uint16_t)offset)>>8)&0x0F);
- tempArray[1]=(uint8_t)(offset);
-
- /* Writes the FC_OFFSET registers */
- g_xStatus = SpiritSpiWriteRegisters(FC_OFFSET1_BASE, 2, tempArray);
-
-}
-
-
-/**
-* @brief Returns the actual frequency offset.
-* @param None.
-* @retval int32_t Frequency offset expressed in Hz as signed word.
-*/
-int32_t SpiritRadioGetFrequencyOffset(void)
-{
- uint8_t tempArray[2];
- int16_t xtalOffsetFactor;
-
- /* Reads the FC_OFFSET registers */
- g_xStatus = SpiritSpiReadRegisters(FC_OFFSET1_BASE, 2, tempArray);
-
- /* Calculates the Offset Factor */
- uint16_t xtalOffTemp = ((((uint16_t)tempArray[0])<<8)+((uint16_t)tempArray[1]));
-
- if(xtalOffTemp & 0x0800)
- {
- xtalOffTemp = xtalOffTemp | 0xF000;
- }
- else
- {
- xtalOffTemp = xtalOffTemp & 0x0FFF;
- }
-
- xtalOffsetFactor = *((int16_t*)(&xtalOffTemp));
-
- /* Calculates the frequency offset and return it */
- return ((int32_t)(xtalOffsetFactor*s_lXtalFrequency)/FBASE_DIVIDER);
-
-}
-
-
-
-/**
-* @brief Sets the Synth word and the Band Select register according to desired base carrier frequency.
-* In this API the Xtal configuration is read out from
-* the corresponding register. The user shall fix it before call this API.
-* @param lFBase the base carrier frequency expressed in Hz as unsigned word.
-* @retval Error code: 0=no error, 1=error during calibration of VCO.
-*/
-uint8_t SpiritRadioSetFrequencyBase(uint32_t lFBase)
-{
- uint32_t synthWord, Fc;
- uint8_t band, anaRadioRegArray[4], wcp;
-
- /* Check the parameter */
- s_assert_param(IS_FREQUENCY_BAND(lFBase));
-
- /* Search the operating band */
- if(IS_FREQUENCY_BAND_HIGH(lFBase))
- {
- band = HIGH_BAND;
- }
- else if(IS_FREQUENCY_BAND_MIDDLE(lFBase))
- {
- band = MIDDLE_BAND;
- }
- else if(IS_FREQUENCY_BAND_LOW(lFBase))
- {
- band = LOW_BAND;
- }
- else
- {
- band = VERY_LOW_BAND;
- }
-
- int32_t FOffset = SpiritRadioGetFrequencyOffset();
- uint32_t lChannelSpace = SpiritRadioGetChannelSpace();
- uint8_t cChannelNum = SpiritRadioGetChannel();
-
- /* Calculates the channel center frequency */
- Fc = lFBase + FOffset + lChannelSpace*cChannelNum;
-
- /* Reads the reference divider */
- uint8_t cRefDiv = (uint8_t)SpiritRadioGetRefDiv()+1;
-
- /* Selects the VCO */
- switch(band)
- {
- case VERY_LOW_BAND:
- if(Fc<161281250)
- {
- SpiritCalibrationSelectVco(VCO_L);
- }
- else
- {
- SpiritCalibrationSelectVco(VCO_H);
- }
- break;
-
- case LOW_BAND:
- if(Fc<322562500)
- {
- SpiritCalibrationSelectVco(VCO_L);
- }
- else
- {
- SpiritCalibrationSelectVco(VCO_H);
- }
- break;
-
- case MIDDLE_BAND:
- if(Fc<430083334)
- {
- SpiritCalibrationSelectVco(VCO_L);
- }
- else
- {
- SpiritCalibrationSelectVco(VCO_H);
- }
- break;
-
- case HIGH_BAND:
- if(Fc<860166667)
- {
- SpiritCalibrationSelectVco(VCO_L);
- }
- else
- {
- SpiritCalibrationSelectVco(VCO_H);
- }
- }
-
- /* Search the VCO charge pump word and set the corresponding register */
- wcp = SpiritRadioSearchWCP(Fc);
-
- synthWord = (uint32_t)(lFBase*s_vectcBHalfFactor[band]*(((double)(FBASE_DIVIDER*cRefDiv))/s_lXtalFrequency));
-
- /* Build the array of registers values for the analog part */
- anaRadioRegArray[0] = (uint8_t)(((synthWord>>21)&(0x0000001F))|(wcp<<5));
- anaRadioRegArray[1] = (uint8_t)((synthWord>>13)&(0x000000FF));
- anaRadioRegArray[2] = (uint8_t)((synthWord>>5)&(0x000000FF));
- anaRadioRegArray[3] = (uint8_t)(((synthWord&0x0000001F)<<3)| s_vectcBandRegValue[band]);
-
- /* Configures the needed Analog Radio registers */
- g_xStatus = SpiritSpiWriteRegisters(SYNT3_BASE, 4, anaRadioRegArray);
-
- if(xDoVcoCalibrationWA==S_ENABLE)
- return SpiritManagementWaVcoCalibration();
-
- return 0;
-}
-
-/**
-* @brief To say to the set frequency base if do or not the VCO calibration WA.
-* @param S_ENABLE or S_DISABLE the WA procedure.
-* @retval None.
-*/
-void SpiritRadioVcoCalibrationWAFB(SpiritFunctionalState xNewstate)
-{
- xDoVcoCalibrationWA=xNewstate;
-}
-
-/**
-* @brief Returns the base carrier frequency.
-* @param None.
-* @retval uint32_t Base carrier frequency expressed in Hz as unsigned word.
-*/
-uint32_t SpiritRadioGetFrequencyBase(void)
-{
- uint32_t synthWord;
- BandSelect band;
-
- /* Reads the synth word */
- synthWord = SpiritRadioGetSynthWord();
-
- /* Reads the operating band */
- band = SpiritRadioGetBand();
-
- uint8_t cRefDiv = (uint8_t)SpiritRadioGetRefDiv() + 1;
-
- /* Calculates the frequency base and return it */
- return (uint32_t)round(synthWord*(((double)s_lXtalFrequency)/(FBASE_DIVIDER*cRefDiv*s_vectcBHalfFactor[band])));
-}
-
-
-/**
-* @brief Returns the actual channel center frequency.
-* @param None.
-* @retval uint32_t Actual channel center frequency expressed in Hz.
-*/
-uint32_t SpiritRadioGetCenterFrequency(void)
-{
- int32_t offset;
- uint8_t channel;
- uint32_t fBase;
- uint32_t channelSpace;
-
- /* Reads the frequency base */
- fBase = SpiritRadioGetFrequencyBase();
-
- /* Reads the frequency offset */
- offset = SpiritRadioGetFrequencyOffset();
-
- /* Reads the channel space */
- channelSpace = SpiritRadioGetChannelSpace();
-
- /* Reads the channel number */
- channel = SpiritRadioGetChannel();
-
- /* Calculates the channel center frequency and return it */
- return (uint32_t)(fBase + offset + (uint32_t)(channelSpace*channel));
-
-}
-
-
-/**
-* @brief Returns the mantissa and exponent, whose value used in the datarate formula
-* will give the datarate value closer to the given datarate.
-* @param fDatarate datarate expressed in bps. This parameter ranging between 100 and 500000.
-* @param pcM pointer to the returned mantissa value.
-* @param pcE pointer to the returned exponent value.
-* @retval None.
-*/
-void SpiritRadioSearchDatarateME(uint32_t lDatarate, uint8_t* pcM, uint8_t* pcE)
-{
- volatile SpiritBool find = S_FALSE;
- int8_t i=15;
- uint8_t cMantissaTmp;
- uint8_t cDivider = 0;
-
- /* Check the parameters */
- s_assert_param(IS_DATARATE(lDatarate));
-
- cDivider = (uint8_t)SpiritRadioGetDigDiv();
-
- /* Search in the datarate array the exponent value */
- while(!find && i>=0)
- {
- if(lDatarate>=(s_lXtalFrequency>>(20-i+cDivider)))
- {
- find = S_TRUE;
- }
- else
- {
- i--;
- }
- }
- i<0 ? i=0 : i;
- *pcE = i;
-
- /* Calculates the mantissa value according to the datarate formula */
- cMantissaTmp = (lDatarate*((uint32_t)1<<(23-i)))/(s_lXtalFrequency>>(5+cDivider))-256;
-
- /* Finds the mantissa value with less approximation */
- int16_t mantissaCalculation[3];
- for(uint8_t j=0;j<3;j++)
- {
- if((cMantissaTmp+j-1))
- {
- mantissaCalculation[j]=lDatarate-(((256+cMantissaTmp+j-1)*(s_lXtalFrequency>>(5+cDivider)))>>(23-i));
- }
- else
- {
- mantissaCalculation[j]=0x7FFF;
- }
- }
- uint16_t mantissaCalculationDelta = 0xFFFF;
- for(uint8_t j=0;j<3;j++)
- {
- if(S_ABS(mantissaCalculation[j])<mantissaCalculationDelta)
- {
- mantissaCalculationDelta = S_ABS(mantissaCalculation[j]);
- *pcM = cMantissaTmp+j-1;
- }
- }
-
-}
-
-
-/**
-* @brief Returns the mantissa and exponent for a given bandwidth.
-* Even if it is possible to pass as parameter any value in the below mentioned range,
-* the API will search the closer value according to a fixed table of channel
-* bandwidth values (@ref s_vectnBandwidth), as defined in the datasheet, returning the corresponding mantissa
-* and exponent value.
-* @param lBandwidth bandwidth expressed in Hz. This parameter ranging between 1100 and 800100.
-* @param pcM pointer to the returned mantissa value.
-* @param pcE pointer to the returned exponent value.
-* @retval None.
-*/
-void SpiritRadioSearchChannelBwME(uint32_t lBandwidth, uint8_t* pcM, uint8_t* pcE)
-{
- int8_t i, i_tmp;
- uint8_t cDivider = 1;
-
- /* Search in the channel filter bandwidth table the exponent value */
- if(SpiritRadioGetDigDiv())
- {
- cDivider = 2;
- }
- else
- {
- cDivider = 1;
- }
-
- s_assert_param(IS_CH_BW(lBandwidth,s_lXtalFrequency/cDivider));
-
- uint32_t lChfltFactor = (s_lXtalFrequency/cDivider)/100;
-
- for(i=0;i<90 && (lBandwidth<(uint32_t)((s_vectnBandwidth26M[i]*lChfltFactor)/2600));i++);
-
- if(i!=0)
- {
- /* Finds the mantissa value with less approximation */
- i_tmp=i;
- int16_t chfltCalculation[3];
- for(uint8_t j=0;j<3;j++)
- {
- if(((i_tmp+j-1)>=0) || ((i_tmp+j-1)<=89))
- {
- chfltCalculation[j] = lBandwidth - (uint32_t)((s_vectnBandwidth26M[i_tmp+j-1]*lChfltFactor)/2600);
- }
- else
- {
- chfltCalculation[j] = 0x7FFF;
- }
- }
- uint16_t chfltDelta = 0xFFFF;
-
- for(uint8_t j=0;j<3;j++)
- {
- if(S_ABS(chfltCalculation[j])<chfltDelta)
- {
- chfltDelta = S_ABS(chfltCalculation[j]);
- i=i_tmp+j-1;
- }
- }
- }
- (*pcE) = (uint8_t)(i/9);
- (*pcM) = (uint8_t)(i%9);
-
-}
-
-/**
-* @brief Returns the mantissa and exponent, whose value used in the frequency deviation formula
-* will give a frequency deviation value most closer to the given frequency deviation.
-* @param fFDev frequency deviation expressed in Hz. This parameter can be a value in the range [F_Xo*8/2^18, F_Xo*7680/2^18].
-* @param pcM pointer to the returned mantissa value.
-* @param pcE pointer to the returned exponent value.
-* @retval None.
-*/
-void SpiritRadioSearchFreqDevME(uint32_t lFDev, uint8_t* pcM, uint8_t* pcE)
-{
- uint8_t i;
- uint32_t a,bp,b=0;
- float xtalDivtmp=(float)s_lXtalFrequency/(((uint32_t)1)<<18);
-
- /* Check the parameters */
- s_assert_param(IS_F_DEV(lFDev,s_lXtalFrequency));
-
- for(i=0;i<10;i++)
- {
- a=(uint32_t)(xtalDivtmp*(uint32_t)(7.5*(1<<i)));
- if(lFDev<a)
- break;
- }
- (*pcE) = i;
-
- for(i=0;i<8;i++)
- {
- bp=b;
- b=(uint32_t)(xtalDivtmp*(uint32_t)((8.0+i)/2*(1<<(*pcE))));
- if(lFDev<b)
- break;
- }
-
- (*pcM)=i;
- if((lFDev-bp)<(b-lFDev))
- (*pcM)--;
-
-}
-
-
-/**
-* @brief Sets the datarate.
-* @param fDatarate datarate expressed in bps. This value shall be in the range
-* [100 500000].
-* @retval None.
-*/
-void SpiritRadioSetDatarate(uint32_t lDatarate)
-{
- uint8_t drE, tempRegValue[2];
-
- /* Check the parameters */
- s_assert_param(IS_DATARATE(lDatarate));
-
- /* Calculates the datarate mantissa and exponent */
- SpiritRadioSearchDatarateME(lDatarate, &tempRegValue[0], &drE);
-
- /* Reads the MOD_O register*/
- SpiritSpiReadRegisters(MOD0_BASE, 1, &tempRegValue[1]);
-
- /* Mask the other fields and set the datarate exponent */
- tempRegValue[1] &= 0xF0;
- tempRegValue[1] |= drE;
-
- /* Writes the Datarate registers */
- g_xStatus = SpiritSpiWriteRegisters(MOD1_BASE, 2, tempRegValue);
-
-}
-
-
-/**
-* @brief Returns the datarate.
-* @param None.
-* @retval uint32_t Settled datarate expressed in bps.
-*/
-uint32_t SpiritRadioGetDatarate(void)
-{
- uint8_t tempRegValue[2];
- uint8_t cDivider=0;
-
- /* Reads the datarate registers for mantissa and exponent */
- g_xStatus = SpiritSpiReadRegisters(MOD1_BASE, 2, tempRegValue);
-
- /* Calculates the datarate */
- cDivider = (uint8_t)SpiritRadioGetDigDiv();
-
- return (((s_lXtalFrequency>>(5+cDivider))*(256+tempRegValue[0]))>>(23-(tempRegValue[1]&0x0F)));
-}
-
-
-/**
-* @brief Sets the frequency deviation.
-* @param fFDev frequency deviation expressed in Hz. Be sure that this value
-* is in the correct range [F_Xo*8/2^18, F_Xo*7680/2^18] Hz.
-* @retval None.
-*/
-void SpiritRadioSetFrequencyDev(uint32_t lFDev)
-{
- uint8_t FDevM, FDevE, tempRegValue;
-
- /* Check the parameters */
- s_assert_param(IS_F_DEV(lFDev, s_lXtalFrequency));
-
- /* Calculates the frequency deviation mantissa and exponent */
- SpiritRadioSearchFreqDevME(lFDev, &FDevM, &FDevE);
-
- /* Reads the FDEV0 register */
- SpiritSpiReadRegisters(FDEV0_BASE, 1, &tempRegValue);
-
- /* Mask the other fields and set the frequency deviation mantissa and exponent */
- tempRegValue &= 0x08;
- tempRegValue |= ((FDevE<<4)|(FDevM));
-
- /* Writes the Frequency deviation register */
- g_xStatus = SpiritSpiWriteRegisters(FDEV0_BASE, 1, &tempRegValue);
-
-}
-
-
-/**
-* @brief Returns the frequency deviation.
-* @param None.
-* @retval uint32_t Frequency deviation value expressed in Hz.
-* This value will be in the range [F_Xo*8/2^18, F_Xo*7680/2^18] Hz.
-*/
-uint32_t SpiritRadioGetFrequencyDev(void)
-{
- uint8_t tempRegValue, FDevM, FDevE;
-
-
- /* Reads the frequency deviation register for mantissa and exponent */
- g_xStatus = SpiritSpiReadRegisters(FDEV0_BASE, 1, &tempRegValue);
- FDevM = tempRegValue&0x07;
- FDevE = (tempRegValue&0xF0)>>4;
-
- /* Calculates the frequency deviation and return it */
- //return (((s_lXtalFrequency>>6)*(8+FDevM))>>(13-FDevE));
-
- return (uint32_t)((float)s_lXtalFrequency/(((uint32_t)1)<<18)*(uint32_t)((8.0+FDevM)/2*(1<<FDevE)));
-
-}
-
-
-/**
-* @brief Sets the channel filter bandwidth.
-* @param lBandwidth channel filter bandwidth expressed in Hz. This parameter shall be in the range [1100 800100]
-* Even if it is possible to pass as parameter any value in the above mentioned range,
-* the API will search the most closer value according to a fixed table of channel
-* bandwidth values (@ref s_vectnBandwidth), as defined in the datasheet. To verify the settled channel bandwidth
-* it is possible to use the SpiritRadioGetChannelBW() API.
-* @retval None.
-*/
-void SpiritRadioSetChannelBW(uint32_t lBandwidth)
-{
- uint8_t bwM, bwE, tempRegValue;
-
- /* Search in the channel filter bandwidth table the exponent value */
- if(SpiritRadioGetDigDiv())
- {
- s_assert_param(IS_CH_BW(lBandwidth,(s_lXtalFrequency/2)));
- }
- else
- {
- s_assert_param(IS_CH_BW(lBandwidth,(s_lXtalFrequency)));
- }
-
- /* Calculates the channel bandwidth mantissa and exponent */
- SpiritRadioSearchChannelBwME(lBandwidth, &bwM, &bwE);
- tempRegValue = (bwM<<4)|(bwE);
-
- /* Writes the Channel filter register */
- g_xStatus = SpiritSpiWriteRegisters(CHFLT_BASE, 1, &tempRegValue);
-
-}
-
-/**
-* @brief Returns the channel filter bandwidth.
-* @param None.
-* @retval uint32_t Channel filter bandwidth expressed in Hz.
-*/
-uint32_t SpiritRadioGetChannelBW(void)
-{
- uint8_t tempRegValue, bwM, bwE;
-
- /* Reads the channel filter register for mantissa and exponent */
- g_xStatus = SpiritSpiReadRegisters(CHFLT_BASE, 1, &tempRegValue);
- bwM = (tempRegValue&0xF0)>>4;
- bwE = tempRegValue&0x0F;
-
- /* Reads the channel filter bandwidth from the look-up table and return it */
- return (uint32_t)(100.0*s_vectnBandwidth26M[bwM+(bwE*9)]*s_lXtalFrequency/26e6);
-
-}
-
-
-/**
-* @brief Sets the modulation type.
-* @param xModulation modulation to set.
-* This parameter shall be of type @ref ModulationSelect .
-* @retval None.
-*/
-void SpiritRadioSetModulation(ModulationSelect xModulation)
-{
- uint8_t tempRegValue;
-
- /* Check the parameters */
- s_assert_param(IS_MODULATION_SELECTED(xModulation));
-
- /* Reads the modulation register */
- SpiritSpiReadRegisters(MOD0_BASE, 1, &tempRegValue);
-
- /* Mask the other fields and set the modulation type */
- tempRegValue &=0x8F;
- tempRegValue |= xModulation;
-
- /* Writes the modulation register */
- g_xStatus = SpiritSpiWriteRegisters(MOD0_BASE, 1, &tempRegValue);
-
-}
-
-
-/**
-* @brief Returns the modulation type used.
-* @param None.
-* @retval ModulationSelect Settled modulation type.
-*/
-ModulationSelect SpiritRadioGetModulation(void)
-{
- uint8_t tempRegValue;
-
- /* Reads the modulation register MOD0*/
- g_xStatus = SpiritSpiReadRegisters(MOD0_BASE, 1, &tempRegValue);
-
- /* Return the modulation type */
- return (ModulationSelect)(tempRegValue&0x70);
-
-}
-
-
-/**
-* @brief Enables or Disables the Continuous Wave transmit mode.
-* @param xNewState new state for power ramping.
-* This parameter can be: S_ENABLE or S_DISABLE .
-* @retval None.
-*/
-void SpiritRadioCWTransmitMode(SpiritFunctionalState xNewState)
-{
- uint8_t tempRegValue;
-
- /* Check the parameters */
- s_assert_param(IS_SPIRIT_FUNCTIONAL_STATE(xNewState));
-
- /* Reads the modulation register MOD0 and mask the CW field */
- SpiritSpiReadRegisters(MOD0_BASE, 1, &tempRegValue);
- if(xNewState == S_ENABLE)
- {
- tempRegValue |=MOD0_CW;
- }
- else
- {
- tempRegValue &= (~MOD0_CW);
- }
-
- /* Writes the new value in the MOD0 register */
- g_xStatus = SpiritSpiWriteRegisters(MOD0_BASE, 1, &tempRegValue);
-
-}
-
-
-/**
-* @brief Sets the OOK Peak Decay.
-* @param xOokDecay Peak decay control for OOK.
-* This parameter shall be of type @ref OokPeakDecay .
-* @retval None.
-*/
-void SpiritRadioSetOokPeakDecay(OokPeakDecay xOokDecay)
-{
- uint8_t tempRegValue;
-
- /* Check the parameters */
- s_assert_param(IS_OOK_PEAK_DECAY(xOokDecay));
-
- /* Reads the RSSI_FLT register */
- SpiritSpiReadRegisters(RSSI_FLT_BASE, 1, &tempRegValue);
-
- /* Mask the other fields and set OOK Peak Decay */
- tempRegValue &= 0xFC;
- tempRegValue |= xOokDecay;
-
- /* Writes the RSSI_FLT register to set the new OOK peak dacay value */
- g_xStatus = SpiritSpiWriteRegisters(RSSI_FLT_BASE, 1, &tempRegValue);
-
-}
-
-
-/**
-* @brief Returns the OOK Peak Decay.
-* @param None
-* @retval OokPeakDecay Ook peak decay value.
-*/
-OokPeakDecay SpiritRadioGetOokPeakDecay(void)
-{
- uint8_t tempRegValue;
-
- /* Reads the OOK peak decay register RSSI_FLT_BASE*/
- g_xStatus = SpiritSpiReadRegisters(RSSI_FLT_BASE, 1, &tempRegValue);
-
- /* Returns the OOK peak decay */
- return (OokPeakDecay) (tempRegValue & 0x03);
-
-}
-
-/**
-* @brief Returns the PA register value that corresponds to the passed dBm power.
-* @param lFbase Frequency base expressed in Hz.
-* @param fPowerdBm Desired power in dBm.
-* @retval Register value as byte.
-* @note The power interpolation curves used by this function have been extracted
-* by measurements done on the divisional evaluation boards.
-*/
-uint8_t SpiritRadioGetdBm2Reg(uint32_t lFBase, float fPowerdBm)
-{
- uint8_t i=0;
- uint8_t j=0;
- float fReg;
-
- if(IS_FREQUENCY_BAND_HIGH(lFBase))
- {
- i=0;
- if(lFBase<900000000) i=1;// 868
- }
- else if(IS_FREQUENCY_BAND_MIDDLE(lFBase))
- {
- i=2;
- }
- else if(IS_FREQUENCY_BAND_LOW(lFBase))
- {
- i=3;
- }
- else if(IS_FREQUENCY_BAND_VERY_LOW(lFBase))
- {
- i=4;
- }
-
- j=1;
- if(fPowerdBm>0 && 13.0/fPowerFactors[i][2]-fPowerFactors[i][3]/fPowerFactors[i][2]<fPowerdBm)
- j=0;
- else if(fPowerdBm<=0 && 40.0/fPowerFactors[i][2]-fPowerFactors[i][3]/fPowerFactors[i][2]>fPowerdBm)
- j=2;
-
- fReg=fPowerFactors[i][2*j]*fPowerdBm+fPowerFactors[i][2*j+1];
-
- if(fReg<1)
- fReg=1;
- else if(fReg>90)
- fReg=90;
-
- return ((uint8_t)fReg);
-}
-
-
-/**
-* @brief Returns the dBm power that corresponds to the value of PA register.
-* @param lFbase Frequency base expressed in Hz.
-* @param cPowerReg Register value of the PA.
-* @retval Power in dBm as float.
-* @note The power interpolation curves used by this function have been extracted
-* by measurements done on the divisional evaluation boards.
-*/
-float SpiritRadioGetReg2dBm(uint32_t lFBase, uint8_t cPowerReg)
-{
- uint8_t i=0;
- uint8_t j=0;
- float fPower;
-
- if(cPowerReg==0 || cPowerReg>90)
- return (-130.0);
-
- if(IS_FREQUENCY_BAND_HIGH(lFBase))
- {
- i=0;
- if(lFBase<900000000) i=1;// 868
- }
- else if(IS_FREQUENCY_BAND_MIDDLE(lFBase))
- {
- i=2;
- }
- else if(IS_FREQUENCY_BAND_LOW(lFBase))
- {
- i=3;
- }
- else if(IS_FREQUENCY_BAND_VERY_LOW(lFBase))
- {
- i=4;
- }
-
- j=1;
- if(cPowerReg<13) j=0;
- else if(cPowerReg>40) j=2;
-
- fPower=(((float)cPowerReg)/fPowerFactors[i][2*j]-fPowerFactors[i][2*j+1]/fPowerFactors[i][2*j]);
-
- return fPower;
-}
-
-/**
-* @brief Configures the Power Amplifier Table and registers with value expressed in dBm.
-* @param cPALevelMaxIndex number of levels to set. This parameter shall be in the range [0:7].
-* @param cWidth step width expressed in terms of bit period units Tb/8.
-* This parameter shall be in the range [1:4].
-* @param xCLoad one of the possible value of the enum type PALoadCapacitor.
-* @arg LOAD_0_PF No additional PA load capacitor
-* @arg LOAD_1_2_PF 1.2pF additional PA load capacitor
-* @arg LOAD_2_4_PF 2.4pF additional PA load capacitor
-* @arg LOAD_3_6_PF 3.6pF additional PA load capacitor
-* @param pfPAtabledBm pointer to an array of PA values in dbm between [-PA_LOWER_LIMIT: PA_UPPER_LIMIT] dbm.
-* The first element shall be the lower level (PA_LEVEL[0]) value and the last element
-* the higher level one (PA_LEVEL[paLevelMaxIndex]).
-* @retval None.
-*/
-void SpiritRadioSetPATabledBm(uint8_t cPALevelMaxIndex, uint8_t cWidth, PALoadCapacitor xCLoad, float* pfPAtabledBm)
-{
- uint8_t palevel[9], address, paLevelValue;
- uint32_t lFBase=SpiritRadioGetFrequencyBase();
-
- /* Check the parameters */
- s_assert_param(IS_PA_MAX_INDEX(cPALevelMaxIndex));
- s_assert_param(IS_PA_STEP_WIDTH(cWidth));
- s_assert_param(IS_PA_LOAD_CAP(xCLoad));
-
- /* Check the PA level in dBm is in the range and calculate the PA_LEVEL value
- to write in the corresponding register using the linearization formula */
- for(int i=0; i<=cPALevelMaxIndex; i++)
- {
- s_assert_param(IS_PAPOWER_DBM(*pfPAtabledBm));
- paLevelValue=SpiritRadioGetdBm2Reg(lFBase,(*pfPAtabledBm));
- palevel[cPALevelMaxIndex-i]=paLevelValue;
- pfPAtabledBm++;
- }
-
- /* Sets the PA_POWER[0] register */
- palevel[cPALevelMaxIndex+1]=xCLoad|(cWidth-1)<<3|cPALevelMaxIndex;
-
- /* Sets the base address */
- address=PA_POWER8_BASE+7-cPALevelMaxIndex;
-
- /* Configures the PA_POWER registers */
- g_xStatus = SpiritSpiWriteRegisters(address, cPALevelMaxIndex+2, palevel);
-
-}
-
-
-/**
-* @brief Returns the Power Amplifier Table and registers, returning values in dBm.
-* @param pcPALevelMaxIndex pointer to the number of levels settled.
-* This parameter will be in the range [0:7].
-* @param pfPAtabledBm pointer to an array of 8 elements containing the PA value in dbm.
-* The first element will be the PA_LEVEL_0 and the last element
-* will be PA_LEVEL_7. Any value higher than PA_UPPER_LIMIT implies no output
-* power (output stage is in high impedance).
-* @retval None.
-*/
-void SpiritRadioGetPATabledBm(uint8_t* pcPALevelMaxIndex, float* pfPAtabledBm)
-{
- uint8_t palevelvect[9];
- uint32_t lFBase=SpiritRadioGetFrequencyBase();
-
- /* Reads the PA_LEVEL_x registers and the PA_POWER_0 register */
- g_xStatus = SpiritSpiReadRegisters(PA_POWER8_BASE, 9, palevelvect);
-
- /* Fill the PAtable */
- for(int i=7; i>=0; i--)
- {
- (*pfPAtabledBm)=SpiritRadioGetReg2dBm(lFBase,palevelvect[i]);
- pfPAtabledBm++;
- }
-
- /* Return the settled index */
- *pcPALevelMaxIndex = palevelvect[8]&0x07;
-
-}
-
-
-
-
-
-
-/**
-* @brief Sets a specific PA_LEVEL register, with a value given in dBm.
-* @param cIndex PA_LEVEL to set. This parameter shall be in the range [0:7].
-* @param fPowerdBm PA value to write expressed in dBm . Be sure that this values is in the
-* correct range [-PA_LOWER_LIMIT: PA_UPPER_LIMIT] dBm.
-* @retval None.
-* @note This function makes use of the @ref SpiritRadioGetdBm2Reg fcn to interpolate the
-* power value.
-*/
-void SpiritRadioSetPALeveldBm(uint8_t cIndex, float fPowerdBm)
-{
- uint8_t address, paLevelValue;
-
- /* Check the parameters */
- s_assert_param(IS_PA_MAX_INDEX(cIndex));
- s_assert_param(IS_PAPOWER_DBM(fPowerdBm));
-
- /* interpolate the power level */
- paLevelValue=SpiritRadioGetdBm2Reg(SpiritRadioGetFrequencyBase(),fPowerdBm);
-
- /* Sets the base address */
- address=PA_POWER8_BASE+7-cIndex;
-
- /* Configures the PA_LEVEL register */
- g_xStatus = SpiritSpiWriteRegisters(address, 1, &paLevelValue);
-
-}
-
-
-/**
-* @brief Returns a specific PA_LEVEL register, returning a value in dBm.
-* @param cIndex PA_LEVEL to read. This parameter shall be in the range [0:7]
-* @retval float Settled power level expressed in dBm. A value
-* higher than PA_UPPER_LIMIT dBm implies no output power
-* (output stage is in high impedance).
-* @note This function makes use of the @ref SpiritRadioGetReg2dBm fcn to interpolate the
-* power value.
-*/
-float SpiritRadioGetPALeveldBm(uint8_t cIndex)
-{
- uint8_t address, paLevelValue;
-
- /* Check the parameters */
- s_assert_param(IS_PA_MAX_INDEX(cIndex));
-
- /* Sets the base address */
- address=PA_POWER8_BASE+7-cIndex;
-
- /* Reads the PA_LEVEL[cIndex] register */
- g_xStatus = SpiritSpiReadRegisters(address, 1, &paLevelValue);
-
- return SpiritRadioGetReg2dBm(SpiritRadioGetFrequencyBase(),paLevelValue);
-}
-
-
-/**
-* @brief Configures the Power Amplifier Table and registers.
-* @param cPALevelMaxIndex number of levels to set. This parameter shall be in the range [0:7].
-* @param cWidth step width expressed in terms of bit period units Tb/8.
-* This parameter shall be in the range [1:4].
-* @param xCLoad one of the possible value of the enum type PALoadCapacitor.
-* @arg LOAD_0_PF No additional PA load capacitor
-* @arg LOAD_1_2_PF 1.2pF additional PA load capacitor
-* @arg LOAD_2_4_PF 2.4pF additional PA load capacitor
-* @arg LOAD_3_6_PF 3.6pF additional PA load capacitor
-* @param pcPAtable pointer to an array of PA values in the range [0: 90], where 0 implies no
-* output power, 1 will be the maximum level and 90 the minimum one
-* The first element shall be the lower level (PA_LEVEL[0]) value and the last element
-* the higher level one (PA_LEVEL[paLevelMaxIndex]).
-* @retval None.
-*/
-void SpiritRadioSetPATable(uint8_t cPALevelMaxIndex, uint8_t cWidth, PALoadCapacitor xCLoad, uint8_t* pcPAtable)
-{
- uint8_t palevel[9], address;
-
- /* Check the parameters */
- s_assert_param(IS_PA_MAX_INDEX(cPALevelMaxIndex));
- s_assert_param(IS_PA_STEP_WIDTH(cWidth));
- s_assert_param(IS_PA_LOAD_CAP(xCLoad));
-
- /* Check the PA levels are in the range */
- for(int i=0; i<=cPALevelMaxIndex; i++)
- {
- s_assert_param(IS_PAPOWER(*pcPAtable));
- palevel[cPALevelMaxIndex-i]=*pcPAtable;
- pcPAtable++;
- }
-
- /* Sets the PA_POWER[0] register */
- palevel[cPALevelMaxIndex+1]=xCLoad|((cWidth-1)<<3)|cPALevelMaxIndex;
-
- /* Sets the base address */
- address=PA_POWER8_BASE+7-cPALevelMaxIndex;
-
- /* Configures the PA_POWER registers */
- g_xStatus = SpiritSpiWriteRegisters(address, cPALevelMaxIndex+2, palevel);
-
-}
-
-
-/**
-* @brief Returns the Power Amplifier Table and registers.
-* @param pcPALevelMaxIndex pointer to the number of levels settled.
-* This parameter shall be in the range [0:7].
-* @param pcPAtable pointer to an array of 8 elements containing the PA value.
-* The first element will be the PA_LEVEL_0 and the last element
-* will be PA_LEVEL_7. Any value equals to 0 implies that level has
-* no output power (output stage is in high impedance).
-* @retval None
-*/
-void SpiritRadioGetPATable(uint8_t* pcPALevelMaxIndex, uint8_t* pcPAtable)
-{
- uint8_t palevelvect[9];
-
- /* Reads the PA_LEVEL_x registers and the PA_POWER_0 register */
- g_xStatus = SpiritSpiReadRegisters(PA_POWER8_BASE, 9, palevelvect);
-
- /* Fill the PAtable */
- for(int i=7; i>=0; i--)
- {
- *pcPAtable = palevelvect[i];
- pcPAtable++;
- }
-
- /* Return the settled index */
- *pcPALevelMaxIndex = palevelvect[8]&0x07;
-
-}
-
-
-/**
-* @brief Sets a specific PA_LEVEL register.
-* @param cIndex PA_LEVEL to set. This parameter shall be in the range [0:7].
-* @param cPower PA value to write in the register. Be sure that this values is in the
-* correct range [0 : 90].
-* @retval None.
-*/
-void SpiritRadioSetPALevel(uint8_t cIndex, uint8_t cPower)
-{
- uint8_t address;
-
- /* Check the parameters */
- s_assert_param(IS_PA_MAX_INDEX(cIndex));
- s_assert_param(IS_PAPOWER(cPower));
-
- /* Sets the base address */
- address=PA_POWER8_BASE+7-cIndex;
-
- /* Configures the PA_LEVEL register */
- g_xStatus = SpiritSpiWriteRegisters(address, 1, &cPower);
-
-}
-
-
-/**
-* @brief Returns a specific PA_LEVEL register.
-* @param cIndex PA_LEVEL to read. This parameter shall be in the range [0:7].
-* @retval uint8_t PA_LEVEL value. A value equal to zero
-* implies no output power (output stage is in high impedance).
-*/
-uint8_t SpiritRadioGetPALevel(uint8_t cIndex)
-{
- uint8_t address, tempRegValue;
-
- /* Check the parameters */
- s_assert_param(IS_PA_MAX_INDEX(cIndex));
-
- /* Sets the base address */
- address=PA_POWER8_BASE+7-cIndex;
-
- /* Reads the PA_LEVEL[cIndex] register and return the value */
- g_xStatus = SpiritSpiReadRegisters(address, 1, &tempRegValue);
- return tempRegValue;
-
-}
-
-
-/**
-* @brief Sets the output stage additional load capacitor bank.
-* @param xCLoad one of the possible value of the enum type PALoadCapacitor.
-* @arg LOAD_0_PF No additional PA load capacitor
-* @arg LOAD_1_2_PF 1.2pF additional PA load capacitor
-* @arg LOAD_2_4_PF 2.4pF additional PA load capacitor
-* @arg LOAD_3_6_PF 3.6pF additional PA load capacitor
-* @retval None.
-*/
-void SpiritRadioSetPACwc(PALoadCapacitor xCLoad)
-{
- uint8_t tempRegValue;
-
- /* Check the parameters */
- s_assert_param(IS_PA_LOAD_CAP(xCLoad));
-
- /* Reads the PA_POWER_0 register */
- SpiritSpiReadRegisters(PA_POWER0_BASE, 1, &tempRegValue);
-
- /* Mask the CWC[1:0] field and write the new value */
- tempRegValue &= 0x3F;
- tempRegValue |= xCLoad;
-
- /* Configures the PA_POWER_0 register */
- g_xStatus = SpiritSpiWriteRegisters(PA_POWER0_BASE, 1, &tempRegValue);
-
-}
-
-
-/**
-* @brief Returns the output stage additional load capacitor bank.
-* @param None.
-* @retval PALoadCapacitor Output stage additional load capacitor bank.
-* This parameter can be:
-* @arg LOAD_0_PF No additional PA load capacitor
-* @arg LOAD_1_2_PF 1.2pF additional PA load capacitor
-* @arg LOAD_2_4_PF 2.4pF additional PA load capacitor
-* @arg LOAD_3_6_PF 3.6pF additional PA load capacitor
-*/
-PALoadCapacitor SpiritRadioGetPACwc(void)
-{
- uint8_t tempRegValue;
-
- /* Reads the PA_POWER_0 register */
- g_xStatus = SpiritSpiReadRegisters(PA_POWER0_BASE, 1, &tempRegValue);
-
- /* Mask the CWC[1:0] field and return the value*/
- return (PALoadCapacitor)(tempRegValue & 0xC0);
-
-}
-
-
-/**
-* @brief Sets a specific PA_LEVEL_MAX_INDEX.
-* @param cIndex PA_LEVEL_MAX_INDEX to set. This parameter shall be in the range [0:7].
-* @retval None
-*/
-void SpiritRadioSetPALevelMaxIndex(uint8_t cIndex)
-{
- uint8_t tempRegValue;
-
- /* Check the parameters */
- s_assert_param(IS_PA_MAX_INDEX(cIndex));
-
- /* Reads the PA_POWER_0 register */
- SpiritSpiReadRegisters(PA_POWER0_BASE, 1, &tempRegValue);
-
- /* Mask the PA_LEVEL_MAX_INDEX[1:0] field and write the new value */
- tempRegValue &= 0xF8;
- tempRegValue |= cIndex;
-
- /* Configures the PA_POWER_0 register */
- g_xStatus = SpiritSpiWriteRegisters(PA_POWER0_BASE, 1, &tempRegValue);
-
-}
-
-
-/**
-* @brief Returns the actual PA_LEVEL_MAX_INDEX.
-* @param None.
-* @retval uint8_t Actual PA_LEVEL_MAX_INDEX. This parameter will be in the range [0:7].
-*/
-uint8_t SpiritRadioGetPALevelMaxIndex(void)
-{
- uint8_t tempRegValue;
-
- /* Reads the PA_POWER_0 register */
- g_xStatus = SpiritSpiReadRegisters(PA_POWER0_BASE, 1, &tempRegValue);
-
- /* Mask the PA_LEVEL_MAX_INDEX[1:0] field and return the value */
- return (tempRegValue & 0x07);
-
-}
-
-
-/**
-* @brief Sets a specific PA_RAMP_STEP_WIDTH.
-* @param cWidth step width expressed in terms of bit period units Tb/8.
-* This parameter shall be in the range [1:4].
-* @retval None.
-*/
-void SpiritRadioSetPAStepWidth(uint8_t cWidth)
-{
- uint8_t tempRegValue;
-
- /* Check the parameters */
- s_assert_param(IS_PA_STEP_WIDTH(cWidth));
-
- /* Reads the PA_POWER_0 register */
- SpiritSpiReadRegisters(PA_POWER0_BASE, 1, &tempRegValue);
-
- /* Mask the PA_RAMP_STEP_WIDTH[1:0] field and write the new value */
- tempRegValue &= 0xE7;
- tempRegValue |= (cWidth-1)<<3;
-
- /* Configures the PA_POWER_0 register */
- g_xStatus = SpiritSpiWriteRegisters(PA_POWER0_BASE, 1, &tempRegValue);
-
-}
-
-
-/**
-* @brief Returns the actual PA_RAMP_STEP_WIDTH.
-* @param None.
-* @retval uint8_t Step width value expressed in terms of bit period units Tb/8.
-* This parameter will be in the range [1:4].
-*/
-uint8_t SpiritRadioGetPAStepWidth(void)
-{
- uint8_t tempRegValue;
-
- /* Reads the PA_POWER_0 register */
- g_xStatus = SpiritSpiReadRegisters(PA_POWER0_BASE, 1, &tempRegValue);
-
- /* Mask the PA_RAMP_STEP_WIDTH[1:0] field and return the value */
- tempRegValue &= 0x18;
- return ((tempRegValue>>3)+1);
-
-}
-
-
-/**
-* @brief Enables or Disables the Power Ramping.
-* @param xNewState new state for power ramping.
-* This parameter can be: S_ENABLE or S_DISABLE.
-* @retval None.
-*/
-void SpiritRadioPARamping(SpiritFunctionalState xNewState)
-{
- uint8_t tempRegValue = 0x00;
-
- /* Check the parameters */
- s_assert_param(IS_SPIRIT_FUNCTIONAL_STATE(xNewState));
-
- /* Reads the PA_POWER_0 register and configure the PA_RAMP_ENABLE field */
- SpiritSpiReadRegisters(PA_POWER0_BASE, 1, &tempRegValue);
- if(xNewState == S_ENABLE)
- {
- tempRegValue |= PA_POWER0_PA_RAMP_MASK;
- }
- else
- {
- tempRegValue &= (~PA_POWER0_PA_RAMP_MASK);
- }
-
- /* Sets the PA_POWER_0 register */
- g_xStatus = SpiritSpiWriteRegisters(PA_POWER0_BASE, 1, &tempRegValue);
-
-}
-
-/**
-* @brief Returns the Power Ramping enable bit.
-* @param xNewState new state for power ramping.
-* This parameter can be: S_ENABLE or S_DISABLE.
-* @retval None.
-*/
-SpiritFunctionalState SpiritRadioGetPARamping(void)
-{
- uint8_t tempRegValue;
-
- /* Reads the PA_POWER_0 register and configure the PA_RAMP_ENABLE field */
- g_xStatus = SpiritSpiReadRegisters(PA_POWER0_BASE, 1, &tempRegValue);
-
- /* Mask and return data */
- return (SpiritFunctionalState)((tempRegValue>>5) & 0x01);
-
-}
-
-
-/**
-* @brief Enables or Disables the AFC.
-* @param xNewState new state for AFC.
-* This parameter can be: S_ENABLE or S_DISABLE.
-* @retval None.
-*/
-void SpiritRadioAFC(SpiritFunctionalState xNewState)
-{
- uint8_t tempRegValue = 0x00;
-
- /* Check the parameters */
- s_assert_param(IS_SPIRIT_FUNCTIONAL_STATE(xNewState));
-
- /* Reads the AFC_2 register and configure the AFC Enabled field */
- SpiritSpiReadRegisters(AFC2_BASE, 1, &tempRegValue);
- if(xNewState == S_ENABLE)
- {
- tempRegValue |= AFC2_AFC_MASK;
- }
- else
- {
- tempRegValue &= (~AFC2_AFC_MASK);
- }
-
- /* Sets the AFC_2 register */
- g_xStatus = SpiritSpiWriteRegisters(AFC2_BASE, 1, &tempRegValue);
-
-}
-
-
-/**
-* @brief Enables or Disables the AFC freeze on sync word detection.
-* @param xNewState new state for AFC freeze on sync word detection.
-* This parameter can be: S_ENABLE or S_DISABLE.
-* @retval None.
-*/
-void SpiritRadioAFCFreezeOnSync(SpiritFunctionalState xNewState)
-{
- uint8_t tempRegValue = 0x00;
-
- /* Check the parameters */
- s_assert_param(IS_SPIRIT_FUNCTIONAL_STATE(xNewState));
-
- /* Reads the AFC_2 register and configure the AFC Freeze on Sync field */
- SpiritSpiReadRegisters(AFC2_BASE, 1, &tempRegValue);
- if(xNewState == S_ENABLE)
- {
- tempRegValue |= AFC2_AFC_FREEZE_ON_SYNC_MASK;
- }
- else
- {
- tempRegValue &= (~AFC2_AFC_FREEZE_ON_SYNC_MASK);
- }
-
- /* Sets the AFC_2 register */
- g_xStatus = SpiritSpiWriteRegisters(AFC2_BASE, 1, &tempRegValue);
-
-}
-
-
-/**
-* @brief Sets the AFC working mode.
-* @param xMode the AFC mode. This parameter can be one of the values defined in @ref AFCMode :
-* @arg AFC_SLICER_CORRECTION AFC loop closed on slicer
-* @arg AFC_2ND_IF_CORRECTION AFC loop closed on 2nd conversion stage
-* @retval None.
-*/
-void SpiritRadioSetAFCMode(AFCMode xMode)
-{
- uint8_t tempRegValue = 0x00;
-
- /* Check the parameters */
- s_assert_param(IS_AFC_MODE(xMode));
-
- /* Reads the AFC_2 register and configure the AFC Mode field */
- SpiritSpiReadRegisters(AFC2_BASE, 1, &tempRegValue);
- if(xMode == AFC_2ND_IF_CORRECTION)
- {
- tempRegValue |= AFC_2ND_IF_CORRECTION;
- }
- else
- {
- tempRegValue &= (~AFC_2ND_IF_CORRECTION);
- }
-
- /* Sets the AFC_2 register */
- g_xStatus = SpiritSpiWriteRegisters(AFC2_BASE, 1, &tempRegValue);
-
-}
-
-
-/**
-* @brief Returns the AFC working mode.
-* @param None.
-* @retval AFCMode Settled AFC mode. This parameter will be one of the values defined in @ref AFCMode :
-* @arg AFC_SLICER_CORRECTION AFC loop closed on slicer
-* @arg AFC_2ND_IF_CORRECTION AFC loop closed on 2nd conversion stage
-*/
-AFCMode SpiritRadioGetAFCMode(void)
-{
- uint8_t tempRegValue;
-
- /* Reads the AFC_2 register */
- g_xStatus = SpiritSpiReadRegisters(AFC2_BASE, 1, &tempRegValue);
-
- /* Mask the AFC Mode field and returns the value */
- return (AFCMode)(tempRegValue & 0x20);
-
-}
-
-
-/**
-* @brief Sets the AFC peak detector leakage.
-* @param cLeakage the peak detector leakage. This parameter shall be in the range:
-* [0:31].
-* @retval None.
-*/
-void SpiritRadioSetAFCPDLeakage(uint8_t cLeakage)
-{
- uint8_t tempRegValue = 0x00;
-
- /* Check the parameters */
- s_assert_param(IS_AFC_PD_LEAKAGE(cLeakage));
-
- /* Reads the AFC_2 register and configure the AFC PD leakage field */
- SpiritSpiReadRegisters(AFC2_BASE, 1, &tempRegValue);
- tempRegValue &= 0xE0;
- tempRegValue |= cLeakage;
-
- /* Sets the AFC_2 register */
- g_xStatus = SpiritSpiWriteRegisters(AFC2_BASE, 1, &tempRegValue);
-
-}
-
-
-/**
-* @brief Returns the AFC peak detector leakage.
-* @param None.
-* @retval uint8_t Peak detector leakage value. This parameter will be in the range:
-* [0:31].
-*/
-uint8_t SpiritRadioGetAFCPDLeakage(void)
-{
- uint8_t tempRegValue;
-
- /* Reads the AFC_2 register */
- g_xStatus = SpiritSpiReadRegisters(AFC2_BASE, 1, &tempRegValue);
-
- /* Mask the AFC PD leakage field and return the value */
- return (tempRegValue & 0x1F);
-
-}
-
-
-/**
-* @brief Sets the length of the AFC fast period expressed as number of samples.
-* @param cLength length of the fast period in number of samples.
-* @retval None.
-*/
-void SpiritRadioSetAFCFastPeriod(uint8_t cLength)
-{
- /* Sets the AFC_1 register */
- g_xStatus = SpiritSpiWriteRegisters(AFC1_BASE, 1, &cLength);
-
-}
-
-
-/**
-* @brief Returns the AFC fast period expressed as number of samples.
-* @param None.
-* @retval uint8_t Length of the fast period in number of samples.
-*/
-uint8_t SpiritRadioGetAFCFastPeriod(void)
-{
- uint8_t tempRegValue;
-
- /* Reads the AFC 1 register and return the value */
- g_xStatus = SpiritSpiReadRegisters(AFC1_BASE, 1, &tempRegValue);
-
- return tempRegValue;
-
-}
-
-
-/**
-* @brief Sets the AFC loop gain in fast mode.
-* @param cGain AFC loop gain in fast mode. This parameter shall be in the range:
-* [0:15].
-* @retval None.
-*/
-void SpiritRadioSetAFCFastGain(uint8_t cGain)
-{
- uint8_t tempRegValue = 0x00;
-
- /* Check the parameters */
- s_assert_param(IS_AFC_FAST_GAIN(cGain));
-
- /* Reads the AFC_0 register and configure the AFC Fast Gain field */
- SpiritSpiReadRegisters(AFC0_BASE, 1, &tempRegValue);
- tempRegValue &= 0x0F;
- tempRegValue |= cGain<<4;
-
- /* Sets the AFC_0 register */
- g_xStatus = SpiritSpiWriteRegisters(AFC0_BASE, 1, &tempRegValue);
-
-}
-
-
-/**
-* @brief Returns the AFC loop gain in fast mode.
-* @param None.
-* @retval uint8_t AFC loop gain in fast mode. This parameter will be in the range:
-* [0:15].
-*/
-uint8_t SpiritRadioGetAFCFastGain(void)
-{
- uint8_t tempRegValue;
-
- /* Reads the AFC_0 register, mask the AFC Fast Gain field and return the value */
- g_xStatus = SpiritSpiReadRegisters(AFC0_BASE, 1, &tempRegValue);
-
- return ((tempRegValue & 0xF0)>>4);
-
-}
-
-
-/**
-* @brief Sets the AFC loop gain in slow mode.
-* @param cGain AFC loop gain in slow mode. This parameter shall be in the range:
-* [0:15].
-* @retval None.
-*/
-void SpiritRadioSetAFCSlowGain(uint8_t cGain)
-{
- uint8_t tempRegValue = 0x00;
-
- /* Check the parameters */
- s_assert_param(IS_AFC_SLOW_GAIN(cGain));
-
- /* Reads the AFC_0 register and configure the AFC Slow Gain field */
- SpiritSpiReadRegisters(AFC0_BASE, 1, &tempRegValue);
- tempRegValue &= 0xF0;
- tempRegValue |= cGain;
-
- /* Sets the AFC_0 register */
- g_xStatus = SpiritSpiWriteRegisters(AFC0_BASE, 1, &tempRegValue);
-
-}
-
-
-/**
-* @brief Returns the AFC loop gain in slow mode.
-* @param None.
-* @retval uint8_t AFC loop gain in slow mode. This parameter will be in the range:
-* [0:15].
-*/
-uint8_t SpiritRadioGetAFCSlowGain(void)
-{
- uint8_t tempRegValue;
-
- /* Reads the AFC_0 register, mask the AFC Slow Gain field and return the value */
- g_xStatus = SpiritSpiReadRegisters(AFC0_BASE, 1, &tempRegValue);
-
- return (tempRegValue & 0x0F);
-
-}
-
-
-/**
-* @brief Returns the AFC correction from the corresponding register.
-* @param None.
-* @retval int8_t AFC correction, read from the corresponding register.
-* This parameter will be in the range [-128:127].
-*/
-int8_t SpiritRadioGetAFCCorrectionReg(void)
-{
- uint8_t tempRegValue;
-
- /* Reads the AFC_CORR register, cast the read value as signed char and return it */
- g_xStatus = SpiritSpiReadRegisters(AFC_CORR_BASE, 1, &tempRegValue);
-
- return (int8_t)tempRegValue;
-
-}
-
-
-/**
-* @brief Returns the AFC correction expressed in Hz.
-* @param None.
-* @retval int32_t AFC correction expressed in Hz
-* according to the following formula:<ul>
-* <li> Fafc[Hz]= (Fdig/(12*2^10))*AFC_CORR where </li>
-* <li> AFC_CORR is the value read in the AFC_CORR register </li> </ul>
-*/
-int32_t SpiritRadioGetAFCCorrectionHz(void)
-{
- int8_t correction;
- uint32_t xtal = s_lXtalFrequency;
-
- /* Reads the AFC correction register */
- correction = SpiritRadioGetAFCCorrectionReg();
-
- if(xtal>DOUBLE_XTAL_THR)
- {
- xtal /= 2;
- }
-
- /* Calculates and return the Frequency Correction */
- return (int32_t)(xtal/(12*pow(2,10))*correction);
-
-}
-
-
-/**
-* @brief Enables or Disables the AGC.
-* @param xNewState new state for AGC.
-* This parameter can be: S_ENABLE or S_DISABLE
-* @retval None.
-*/
-void SpiritRadioAGC(SpiritFunctionalState xNewState)
-{
- uint8_t tempRegValue = 0x00;
-
- /* Check the parameters */
- s_assert_param(IS_SPIRIT_FUNCTIONAL_STATE(xNewState));
-
- /* Reads the AGCCTRL_0 register and configure the AGC Enabled field */
- SpiritSpiReadRegisters(AGCCTRL0_BASE, 1, &tempRegValue);
- if(xNewState == S_ENABLE)
- {
- tempRegValue |= AGCCTRL0_AGC_MASK;
- }
- else
- {
- tempRegValue &= (~AGCCTRL0_AGC_MASK);
- }
-
- /* Sets the AGCCTRL_0 register */
- g_xStatus = SpiritSpiWriteRegisters(AGCCTRL0_BASE, 1, &tempRegValue);
-
-}
-
-
-/**
-* @brief Sets the AGC working mode.
-* @param xMode the AGC mode. This parameter can be one of the values defined in @ref AGCMode :
-* @arg AGC_LINEAR_MODE AGC works in linear mode
-* @arg AGC_BINARY_MODE AGC works in binary mode
-* @retval None.
-*/
-void SpiritRadioSetAGCMode(AGCMode xMode)
-{
- uint8_t tempRegValue = 0x00;
-
- /* Check the parameters */
- s_assert_param(IS_AGC_MODE(xMode));
-
- /* Reads the AGCCTRL_0 register and configure the AGC Mode field */
- SpiritSpiReadRegisters(AGCCTRL0_BASE, 1, &tempRegValue);
- if(xMode == AGC_BINARY_MODE)
- {
- tempRegValue |= AGC_BINARY_MODE;
- }
- else
- {
- tempRegValue &= (~AGC_BINARY_MODE);
- }
-
- /* Sets the AGCCTRL_0 register */
- g_xStatus = SpiritSpiWriteRegisters(AGCCTRL0_BASE, 1, &tempRegValue);
-
-}
-
-
-/**
-* @brief Returns the AGC working mode.
-* @param None.
-* @retval AGCMode Settled AGC mode. This parameter can be one of the values defined in @ref AGCMode :
-* @arg AGC_LINEAR_MODE AGC works in linear mode
-* @arg AGC_BINARY_MODE AGC works in binary mode
-*/
-AGCMode SpiritRadioGetAGCMode(void)
-{
- uint8_t tempRegValue;
-
- /* Reads the AGCCTRL_0 register, mask the AGC Mode field and return the value */
- g_xStatus = SpiritSpiReadRegisters(AGCCTRL0_BASE, 1, &tempRegValue);
-
- return (AGCMode)(tempRegValue & 0x40);
-
-}
-
-
-/**
-* @brief Enables or Disables the AGC freeze on steady state.
-* @param xNewState new state for AGC freeze on steady state.
-* This parameter can be: S_ENABLE or S_DISABLE.
-* @retval None.
-*/
-void SpiritRadioAGCFreezeOnSteady(SpiritFunctionalState xNewState)
-{
- uint8_t tempRegValue = 0x00;
-
- /* Check the parameters */
- s_assert_param(IS_SPIRIT_FUNCTIONAL_STATE(xNewState));
-
- /* Reads the AGCCTRL_2 register and configure the AGC Freeze On Steady field */
- SpiritSpiReadRegisters(AGCCTRL2_BASE, 1, &tempRegValue);
- if(xNewState == S_ENABLE)
- {
- tempRegValue |= AGCCTRL2_FREEZE_ON_STEADY_MASK;
- }
- else
- {
- tempRegValue &= (~AGCCTRL2_FREEZE_ON_STEADY_MASK);
- }
-
- /* Sets the AGCCTRL_2 register */
- g_xStatus = SpiritSpiWriteRegisters(AGCCTRL2_BASE, 1, &tempRegValue);
-
-}
-
-
-/**
-* @brief Enable or Disable the AGC freeze on sync detection.
-* @param xNewState new state for AGC freeze on sync detection.
-* This parameter can be: S_ENABLE or S_DISABLE.
-* @retval None.
-*/
-void SpiritRadioAGCFreezeOnSync(SpiritFunctionalState xNewState)
-{
- uint8_t tempRegValue = 0x00;
-
- /* Check the parameters */
- s_assert_param(IS_SPIRIT_FUNCTIONAL_STATE(xNewState));
-
- /* Reads the AGCCTRL_2 register and configure the AGC Freeze On Sync field */
- SpiritSpiReadRegisters(AGCCTRL2_BASE, 1, &tempRegValue);
- if(xNewState == S_ENABLE)
- {
- tempRegValue |= AGCCTRL2_FREEZE_ON_SYNC_MASK;
- }
- else
- {
- tempRegValue &= (~AGCCTRL2_FREEZE_ON_SYNC_MASK);
- }
-
- /* Sets the AGCCTRL_2 register */
- g_xStatus = SpiritSpiWriteRegisters(AGCCTRL2_BASE, 1, &tempRegValue);
-
-}
-
-
-/**
-* @brief Enable or Disable the AGC to start with max attenuation.
-* @param xNewState new state for AGC start with max attenuation mode.
-* This parameter can be: S_ENABLE or S_DISABLE.
-* @retval None.
-*/
-void SpiritRadioAGCStartMaxAttenuation(SpiritFunctionalState xNewState)
-{
- uint8_t tempRegValue = 0x00;
-
- /* Check the parameters */
- s_assert_param(IS_SPIRIT_FUNCTIONAL_STATE(xNewState));
-
- /* Reads the AGCCTRL_2 register and configure the AGC Start Max Attenuation field */
- SpiritSpiReadRegisters(AGCCTRL2_BASE, 1, &tempRegValue);
- if(xNewState == S_ENABLE)
- {
- tempRegValue |= AGCCTRL2_START_MAX_ATTENUATION_MASK;
- }
- else
- {
- tempRegValue &= (~AGCCTRL2_START_MAX_ATTENUATION_MASK);
- }
-
- /* Sets the AGCCTRL_2 register */
- g_xStatus = SpiritSpiWriteRegisters(AGCCTRL2_BASE, 1, &tempRegValue);
-
-}
-
-
-/**
-* @brief Sets the AGC measure time.
-* @param nTime AGC measure time expressed in us. This parameter shall be in the range [0, 393216/F_Xo].
-* @retval None.
-*/
-void SpiritRadioSetAGCMeasureTimeUs(uint16_t nTime)
-{
- uint8_t tempRegValue, measure;
-
- /* Check the parameter */
- s_assert_param(IS_AGC_MEASURE_TIME_US(nTime,s_lXtalFrequency));
-
- /* Reads the AGCCTRL_2 register */
- SpiritSpiReadRegisters(AGCCTRL2_BASE, 1, &tempRegValue);
-
- /* Calculates the measure time value to write in the register */
- measure = (uint8_t)lroundf(log2((float)nTime/1e6 * s_lXtalFrequency/12));
- (measure>15) ? (measure=15):(measure);
-
- /* Mask the MEAS_TIME field and write the new value */
- tempRegValue &= 0xF0;
- tempRegValue |= measure;
-
- /* Sets the AGCCTRL_2 register */
- g_xStatus = SpiritSpiWriteRegisters(AGCCTRL2_BASE, 1, &tempRegValue);
-
-}
-
-
-/**
-* @brief Returns the AGC measure time.
-* @param None.
-* @retval uint16_t AGC measure time expressed in us. This parameter will be in the range [0, 393216/F_Xo].
-*/
-uint16_t SpiritRadioGetAGCMeasureTimeUs(void)
-{
- uint8_t measure;
-
- /* Reads the AGCCTRL_2 register */
- g_xStatus = SpiritSpiReadRegisters(AGCCTRL2_BASE, 1, &measure);
-
- /* Mask the MEAS_TIME field */
- measure &= 0x0F;
-
- /* Calculates the measure time value to write in the register */
- return (uint16_t)((12.0/s_lXtalFrequency)*(float)pow(2,measure)*1e6);
-
-}
-
-
-/**
-* @brief Sets the AGC measure time.
-* @param cTime AGC measure time to write in the MEAS_TIME field of AGCCTRL_2 register.
-* This parameter shall be in the range [0:15].
-* @retval None.
-*/
-void SpiritRadioSetAGCMeasureTime(uint8_t cTime)
-{
- uint8_t tempRegValue;
-
- /* Check the parameter */
- s_assert_param(IS_AGC_MEASURE_TIME(cTime));
-
- /* Reads the AGCCTRL_2 register */
- SpiritSpiReadRegisters(AGCCTRL2_BASE, 1, &tempRegValue);
-
- /* Mask the MEAS_TIME field and write the new value */
- tempRegValue &= 0xF0;
- tempRegValue |= cTime;
-
- /* Sets the AGCCTRL_2 register */
- g_xStatus = SpiritSpiWriteRegisters(AGCCTRL2_BASE, 1, &tempRegValue);
-
-}
-
-
-/**
-* @brief Returns the AGC measure time.
-* @param None.
-* @retval uint8_t AGC measure time read from the MEAS_TIME field of AGCCTRL_2 register.
-* This parameter will be in the range [0:15].
-*/
-uint8_t SpiritRadioGetAGCMeasureTime(void)
-{
- uint8_t tempRegValue;
-
- /* Reads the AGCCTRL_2 register, mask the MEAS_TIME field and return the value */
- g_xStatus = SpiritSpiReadRegisters(AGCCTRL2_BASE, 1, &tempRegValue);
-
- return (tempRegValue & 0x0F);
-
-}
-
-
-/**
-* @brief Sets the AGC hold time.
-* @param cTime AGC hold time expressed in us. This parameter shall be in the range[0, 756/F_Xo].
-* @retval None.
-*/
-void SpiritRadioSetAGCHoldTimeUs(uint8_t cTime)
-{
- uint8_t tempRegValue, hold;
-
- /* Check the parameter */
- s_assert_param(IS_AGC_HOLD_TIME_US(cTime,s_lXtalFrequency));
-
- /* Reads the AGCCTRL_0 register */
- SpiritSpiReadRegisters(AGCCTRL0_BASE, 1, &tempRegValue);
-
- /* Calculates the hold time value to write in the register */
- hold = (uint8_t)lroundf(((float)cTime/1e6 * s_lXtalFrequency)/12);
- (hold>63) ? (hold=63):(hold);
-
- /* Mask the HOLD_TIME field and write the new value */
- tempRegValue &= 0xC0;
- tempRegValue |= hold;
-
- /* Sets the AGCCTRL_0 register */
- g_xStatus = SpiritSpiWriteRegisters(AGCCTRL0_BASE, 1, &tempRegValue);
-
-}
-
-
-/**
-* @brief Returns the AGC hold time.
-* @param None.
-* @retval uint8_t AGC hold time expressed in us. This parameter will be in the range:
-* [0, 756/F_Xo].
-*/
-uint8_t SpiritRadioGetAGCHoldTimeUs(void)
-{
- uint8_t tempRegValue;
-
- /* Reads the AGCCTRL_0 register */
- g_xStatus = SpiritSpiReadRegisters(AGCCTRL0_BASE, 1, &tempRegValue);
-
- /* Mask the HOLD_TIME field */
- tempRegValue &= 0x3F;
-
- /* Calculates the hold time value and return it */
- return (uint8_t)lroundf ((12.0/s_lXtalFrequency)*(tempRegValue*1e6));
-
-}
-
-
-/**
-* @brief Sets the AGC hold time.
-* @param cTime AGC hold time to write in the HOLD_TIME field of AGCCTRL_0 register.
-* This parameter shall be in the range [0:63].
-* @retval None.
-*/
-void SpiritRadioSetAGCHoldTime(uint8_t cTime)
-{
- uint8_t tempRegValue;
-
- /* Check the parameter */
- s_assert_param(IS_AGC_HOLD_TIME(cTime));
-
- /* Reads the AGCCTRL_0 register */
- SpiritSpiReadRegisters(AGCCTRL0_BASE, 1, &tempRegValue);
-
- /* Mask the HOLD_TIME field and write the new value */
- tempRegValue &= 0xC0;
- tempRegValue |= cTime;
-
- /* Sets the AGCCTRL_0 register */
- g_xStatus = SpiritSpiWriteRegisters(AGCCTRL0_BASE, 1, &tempRegValue);
-
-}
-
-
-/**
-* @brief Returns the AGC hold time.
-* @param None.
-* @retval uint8_t AGC hold time read from the HOLD_TIME field of AGCCTRL_0 register.
-* This parameter will be in the range [0:63].
-*/
-uint8_t SpiritRadioGetAGCHoldTime(void)
-{
- uint8_t tempRegValue;
-
- /* Reads the AGCCTRL_0 register, mask the MEAS_TIME field and return the value */
- g_xStatus = SpiritSpiReadRegisters(AGCCTRL0_BASE, 1, &tempRegValue);
-
- return (tempRegValue & 0x3F);
-
-}
-
-
-/**
-* @brief Sets the AGC high threshold.
-* @param cHighThreshold AGC high threshold to write in the THRESHOLD_HIGH field of AGCCTRL_1 register.
-* This parameter shall be in the range [0:15].
-* @retval None.
-*/
-void SpiritRadioSetAGCHighThreshold(uint8_t cHighThreshold)
-{
- uint8_t tempRegValue;
-
- /* Check the parameter */
- s_assert_param(IS_AGC_THRESHOLD(cHighThreshold));
-
- /* Reads the AGCCTRL_1 register */
- SpiritSpiReadRegisters(AGCCTRL1_BASE, 1, &tempRegValue);
-
- /* Mask the THRESHOLD_HIGH field and write the new value */
- tempRegValue &= 0x0F;
- tempRegValue |= cHighThreshold<<4;
-
- /* Sets the AGCCTRL_1 register */
- g_xStatus = SpiritSpiWriteRegisters(AGCCTRL1_BASE, 1, &tempRegValue);
-
-}
-
-
-/**
-* @brief Returns the AGC high threshold.
-* @param None.
-* @retval uint8_t AGC high threshold read from the THRESHOLD_HIGH field of AGCCTRL_1 register.
-* This parameter will be in the range [0:15].
-*/
-uint8_t SpiritRadioGetAGCHighThreshold(void)
-{
- uint8_t tempRegValue;
-
- /* Reads the AGCCTRL_1 register, mask the THRESHOLD_HIGH field and return the value */
- g_xStatus = SpiritSpiReadRegisters(AGCCTRL1_BASE, 1, &tempRegValue);
-
- return ((tempRegValue & 0xF0)>>4);
-
-}
-
-
-/**
-* @brief Sets the AGC low threshold.
-* @param cLowThreshold AGC low threshold to write in the THRESHOLD_LOW field of AGCCTRL_1 register.
-* This parameter shall be in the range [0:15].
-* @retval None.
-*/
-void SpiritRadioSetAGCLowThreshold(uint8_t cLowThreshold)
-{
- uint8_t tempRegValue;
-
- /* Check the parameter */
- s_assert_param(IS_AGC_THRESHOLD(cLowThreshold));
-
- /* Reads the AGCCTRL_1 register */
- SpiritSpiReadRegisters(AGCCTRL1_BASE, 1, &tempRegValue);
-
- /* Mask the THRESHOLD_LOW field and write the new value */
- tempRegValue &= 0xF0;
- tempRegValue |= cLowThreshold;
-
- /* Sets the AGCCTRL_1 register */
- g_xStatus = SpiritSpiWriteRegisters(AGCCTRL1_BASE, 1, &tempRegValue);
-
-}
-
-
-/**
-* @brief Returns the AGC low threshold.
-* @param None.
-* @retval uint8_t AGC low threshold read from the THRESHOLD_LOW field of AGCCTRL_1 register.
-* This parameter will be in the range [0:15].
-*/
-uint8_t SpiritRadioGetAGCLowThreshold(void)
-{
- uint8_t tempRegValue;
-
- /* Reads the AGCCTRL_1 register, mask the THRESHOLD_LOW field and return the value */
- g_xStatus = SpiritSpiReadRegisters(AGCCTRL1_BASE, 1, &tempRegValue);
-
- return (tempRegValue & 0x0F);
-
-}
-
-
-/**
-* @brief Sets the clock recovery algorithm.
-* @param xMode the Clock Recovery mode. This parameter can be one of the values defined in @ref ClkRecMode :
-* @arg CLK_REC_PLL PLL alogrithm for clock recovery
-* @arg CLK_REC_DLL DLL alogrithm for clock recovery
-* @retval None.
-*/
-void SpiritRadioSetClkRecMode(ClkRecMode xMode)
-{
- uint8_t tempRegValue;
-
- /* Check the parameter */
- s_assert_param(IS_CLK_REC_MODE(xMode));
-
- /* Reads the FDEV_0 register */
- SpiritSpiReadRegisters(FDEV0_BASE, 1, &tempRegValue);
-
- /* Mask the CLOCK_REC_ALGO_SEL field and write the new value */
- tempRegValue &= 0xF7;
- tempRegValue |= (uint8_t)xMode;
-
- /* Sets the FDEV_0 register */
- g_xStatus = SpiritSpiWriteRegisters(FDEV0_BASE, 1, &tempRegValue);
-
-}
-
-
-/**
-* @brief Returns the Clock Recovery working mode.
-* @param None.
-* @retval ClkRecMode Clock Recovery mode. This parameter can be one of the values defined in @ref ClkRecMode :
-* @arg CLK_REC_PLL PLL alogrithm for clock recovery
-* @arg CLK_REC_DLL DLL alogrithm for clock recovery
-*/
-ClkRecMode SpiritRadioGetClkRecMode(void)
-{
- uint8_t tempRegValue;
-
- /* Reads the FDEV_0 register, mask the CLOCK_REC_ALGO_SEL field and return the value */
- g_xStatus = SpiritSpiReadRegisters(FDEV0_BASE, 1, &tempRegValue);
-
- return (ClkRecMode)(tempRegValue & 0x08);
-
-}
-
-
-/**
-* @brief Sets the clock recovery proportional gain.
-* @param cPGain the Clock Recovery proportional gain to write in the CLK_REC_P_GAIN field of CLOCKREC register.
-* It represents is log2 value of the clock recovery proportional gain.
-* This parameter shall be in the range [0:7].
-* @retval None.
-*/
-void SpiritRadioSetClkRecPGain(uint8_t cPGain)
-{
- uint8_t tempRegValue;
-
- /* Check the parameter */
- s_assert_param(IS_CLK_REC_P_GAIN(cPGain));
-
- /* Reads the CLOCKREC register */
- SpiritSpiReadRegisters(CLOCKREC_BASE, 1, &tempRegValue);
-
- /* Mask the CLK_REC_P_GAIN field and write the new value */
- tempRegValue &= 0x1F;
- tempRegValue |= (cPGain<<5);
-
- /* Sets the CLOCKREC register */
- g_xStatus = SpiritSpiWriteRegisters(CLOCKREC_BASE, 1, &tempRegValue);
-
-}
-
-
-/**
-* @brief Returns the log2 of the clock recovery proportional gain.
-* @param None.
-* @retval uint8_t Clock Recovery proportional gain read from the CLK_REC_P_GAIN field of CLOCKREC register.
-* This parameter will be in the range [0:7].
-*/
-uint8_t SpiritRadioGetClkRecPGain(void)
-{
- uint8_t tempRegValue;
-
- /* Reads the CLOCKREC register, mask the CLK_REC_P_GAIN field and return the value */
- g_xStatus = SpiritSpiReadRegisters(CLOCKREC_BASE, 1, &tempRegValue);
-
- return ((tempRegValue & 0xEF)>>5);
-
-}
-
-
-/**
-* @brief Sets the clock recovery integral gain.
-* @param cIGain the Clock Recovery integral gain to write in the CLK_REC_I_GAIN field of CLOCKREC register.
-* This parameter shall be in the range [0:15].
-* @retval None.
-*/
-void SpiritRadioSetClkRecIGain(uint8_t cIGain)
-{
- uint8_t tempRegValue;
-
- /* Check the parameter */
- s_assert_param(IS_CLK_REC_I_GAIN(cIGain));
-
- /* Reads the CLOCKREC register */
- SpiritSpiReadRegisters(CLOCKREC_BASE, 1, &tempRegValue);
-
- /* Mask the CLK_REC_P_GAIN field and write the new value */
- tempRegValue &= 0xF0;
- tempRegValue |= cIGain;
-
- /* Sets the CLOCKREC register */
- g_xStatus = SpiritSpiWriteRegisters(CLOCKREC_BASE, 1, &tempRegValue);
-
-}
-
-
-/**
-* @brief Returns the clock recovery integral gain.
-* @param None.
-* @retval uint8_t Clock Recovery integral gain read from the
-* CLK_REC_I_GAIN field of CLOCKREC register.
-* This parameter will be in the range [0:15].
-*/
-uint8_t SpiritRadioGetClkRecIGain(void)
-{
- uint8_t tempRegValue;
-
- /* Reads the CLOCKREC register, mask the CLK_REC_I_GAIN field and return the value */
- g_xStatus = SpiritSpiReadRegisters(CLOCKREC_BASE, 1, &tempRegValue);
-
- return (tempRegValue & 0x0F);
-
-}
-
-
-/**
-* @brief Sets the postfilter length for clock recovery algorithm.
-* @param xLength the postfilter length in symbols. This parameter can be one of the values defined in @ref PstFltLength :
-* @arg PSTFLT_LENGTH_8 Postfilter length is 8 symbols
-* @arg PSTFLT_LENGTH_16 Postfilter length is 16 symbols
-* @retval None.
-*/
-void SpiritRadioSetClkRecPstFltLength(PstFltLength xLength)
-{
- uint8_t tempRegValue;
-
- /* Check the parameter */
- s_assert_param(IS_PST_FLT_LENGTH(xLength));
-
- /* Reads the CLOCKREC register */
- SpiritSpiReadRegisters(CLOCKREC_BASE, 1, &tempRegValue);
-
- /* Mask the PSTFLT_LEN field and write the new value */
- tempRegValue &= 0xEF;
- tempRegValue |= (uint8_t)xLength;
-
- /* Sets the CLOCKREC register */
- g_xStatus = SpiritSpiWriteRegisters(CLOCKREC_BASE, 1, &tempRegValue);
-
-}
-
-
-/**
-* @brief Returns the postfilter length for clock recovery algorithm.
-* @param None.
-* @retval PstFltLength Postfilter length in symbols. This parameter can be one of the values defined in @ref PstFltLength :
-* @arg PSTFLT_LENGTH_8 Postfilter length is 8 symbols
-* @arg PSTFLT_LENGTH_16 Postfilter length is 16 symbols
-*/
-PstFltLength SpiritRadioGetClkRecPstFltLength(void)
-{
- uint8_t tempRegValue;
-
- /* Reads the CLOCKREC register, mask the PSTFLT_LEN field and return the value */
- g_xStatus = SpiritSpiReadRegisters(CLOCKREC_BASE, 1, &tempRegValue);
-
- return (PstFltLength)(tempRegValue & 0x10);
-
-}
-
-
-/**
-* @brief Enables or Disables the received data blanking when the CS is under the threshold.
-* @param xNewState new state of this mode.
-* This parameter can be: S_ENABLE or S_DISABLE .
-* @retval None.
-*/
-void SpiritRadioCsBlanking(SpiritFunctionalState xNewState)
-{
- uint8_t tempRegValue;
-
- /* Check the parameters */
- s_assert_param(IS_SPIRIT_FUNCTIONAL_STATE(xNewState));
-
- /* Reads the ANT_SELECT_CONF_BASE and mask the CS_BLANKING BIT field */
- SpiritSpiReadRegisters(ANT_SELECT_CONF_BASE, 1, &tempRegValue);
-
- if(xNewState == S_ENABLE)
- {
- tempRegValue |= ANT_SELECT_CS_BLANKING_MASK;
- }
- else
- {
- tempRegValue &= (~ANT_SELECT_CS_BLANKING_MASK);
- }
-
- /* Writes the new value in the ANT_SELECT_CONF register */
- g_xStatus = SpiritSpiWriteRegisters(ANT_SELECT_CONF_BASE, 1, &tempRegValue);
-
-
-}
-
-/**
-* @brief Enables or Disables the persistent RX mode.
-* @param xNewState new state of this mode.
-* This parameter can be: S_ENABLE or S_DISABLE .
-* @retval None.
-*/
-void SpiritRadioPersistenRx(SpiritFunctionalState xNewState)
-{
- uint8_t tempRegValue;
-
- /* Check the parameters */
- s_assert_param(IS_SPIRIT_FUNCTIONAL_STATE(xNewState));
-
- /* Reads the PROTOCOL0_BASE and mask the PROTOCOL0_PERS_RX_MASK bitfield */
- SpiritSpiReadRegisters(PROTOCOL0_BASE, 1, &tempRegValue);
-
- if(xNewState == S_ENABLE)
- {
- tempRegValue |= PROTOCOL0_PERS_RX_MASK;
- }
- else
- {
- tempRegValue &= (~PROTOCOL0_PERS_RX_MASK);
- }
-
- /* Writes the new value in the PROTOCOL0_BASE register */
- g_xStatus = SpiritSpiWriteRegisters(PROTOCOL0_BASE, 1, &tempRegValue);
-
-}
-
-/**
-* @brief Enables or Disables the synthesizer reference divider.
-* @param xNewState new state for synthesizer reference divider.
-* This parameter can be: S_ENABLE or S_DISABLE .
-* @retval None.
-*/
-void SpiritRadioSetRefDiv(SpiritFunctionalState xNewState)
-{
- uint8_t tempRegValue;
-
- /* Check the parameters */
- s_assert_param(IS_SPIRIT_FUNCTIONAL_STATE(xNewState));
-
- /* Reads the SYNTH_CONFIG1_BASE and mask the REFDIV bit field */
- SpiritSpiReadRegisters(SYNTH_CONFIG1_BASE, 1, &tempRegValue);
-
- if(xNewState == S_ENABLE)
- {
- tempRegValue |= 0x80;
- }
- else
- {
- tempRegValue &= 0x7F;
- }
-
- /* Writes the new value in the SYNTH_CONFIG1_BASE register */
- g_xStatus = SpiritSpiWriteRegisters(SYNTH_CONFIG1_BASE, 1, &tempRegValue);
-
-}
-
-/**
-* @brief Get the the synthesizer reference divider state.
-* @param void.
-* @retval None.
-*/
-SpiritFunctionalState SpiritRadioGetRefDiv(void)
-{
- uint8_t tempRegValue;
-
- g_xStatus = SpiritSpiReadRegisters(SYNTH_CONFIG1_BASE, 1, &tempRegValue);
-
- if(((tempRegValue>>7)&0x1))
- {
- return S_ENABLE;
- }
- else
- {
- return S_DISABLE;
- }
-
-}
-
-/**
-* @brief Enables or Disables the synthesizer reference divider.
-* @param xNewState new state for synthesizer reference divider.
-* This parameter can be: S_ENABLE or S_DISABLE .
-* @retval None.
-*/
-void SpiritRadioSetDigDiv(SpiritFunctionalState xNewState)
-{
- uint8_t tempRegValue;
-
- /* Check the parameters */
- s_assert_param(IS_SPIRIT_FUNCTIONAL_STATE(xNewState));
-
- /* Reads the XO_RCO_TEST_BASE and mask the PD_CLKDIV bit field */
- SpiritSpiReadRegisters(XO_RCO_TEST_BASE, 1, &tempRegValue);
-
- if(xNewState == S_ENABLE)
- {
- tempRegValue &= 0xf7;
- }
- else
- {
-
- tempRegValue |= 0x08;
- }
-
- /* Writes the new value in the XO_RCO_TEST_BASE register */
- g_xStatus = SpiritSpiWriteRegisters(XO_RCO_TEST_BASE, 1, &tempRegValue);
-
-}
-
-/**
-* @brief Get the the synthesizer reference divider state.
-* @param void.
-* @retval None.
-*/
-SpiritFunctionalState SpiritRadioGetDigDiv(void)
-{
- uint8_t tempRegValue;
-
- g_xStatus = SpiritSpiReadRegisters(XO_RCO_TEST_BASE, 1, &tempRegValue);
-
- if(((tempRegValue>>3)&0x1))
- {
- return S_DISABLE;
- }
- else
- {
- return S_ENABLE;
- }
-
-}
-
-/**
-* @brief Returns the XTAL frequency.
-* @param void.
-* @retval uint32_t XTAL frequency.
-*/
-uint32_t SpiritRadioGetXtalFrequency(void)
-{
- return s_lXtalFrequency;
-}
-
-/**
-* @brief Sets the XTAL frequency.
-* @param uint32_t XTAL frequency.
-* @retval void.
-*/
-void SpiritRadioSetXtalFrequency(uint32_t lXtalFrequency)
-{
- s_lXtalFrequency = lXtalFrequency;
-}
-
-/**
-* @}
-*/
-
-
-/**
-* @}
-*/
-
-
-/**
-* @}
-*/
-
-
-
-/******************* (C) COPYRIGHT 2015 STMicroelectronics *****END OF FILE****/
-
Repository toolbox
| Export to desktop IDE |
Repository details
| Type: | Library |
|---|---|
| Created: | 05 Jul 2017 |
| Imports: | 273 |
| Forks: | 2 |
| Commits: | 83 |
| Dependents: | 0 |
| Dependencies: | 0 |
| Followers: | 410 |
The code in this repository is Apache licensed.
Components
X-NUCLEO-IDS01A4 Sub-1GHz RF Expansion Board