Prototype RF driver for STM Sub-1 GHz RF expansion board based on the SPSGRF-868 module for STM32 Nucleo.
Prototype RF Driver for STM Sub-1 GHz RF Expansion Boards based on the SPSGRF-868 and SPSGRF-915 Modules for STM32 Nucleo
Currently supported boards:
Note, in order to use expansion board X-NUCLEO-IDS01A4 in mbed you need to perform the following HW modifications on the board:
- Unmount resistor
R4 - Mount resistor
R7
Furthermore, on some Nucleo development boards (e.g. the NUCLEO_F429ZI), in order to be able to use Ethernet together with these Sub-1 GHz RF expansion boards, you need to compile this driver with macro SPIRIT1_SPI_MOSI=PB_5 defined, while the development board typically requires some HW modification as e.g. described here!
This driver can be used together with the 6LoWPAN stack (a.k.a. Nanostack).
Diff: libs/Contiki_STM32_Library/platform-conf.h
- Revision:
- 34:edda6a7238ec
- Parent:
- 33:c226804be492
- Child:
- 35:f3f444c379d0
--- a/libs/Contiki_STM32_Library/platform-conf.h Mon Nov 21 13:26:17 2016 +0100
+++ /dev/null Thu Jan 01 00:00:00 1970 +0000
@@ -1,197 +0,0 @@
-/**
-******************************************************************************
-* @file platform/stm32nucleo-spirit1/platform-conf.h
-* @author System LAB
-* @version V1.0.0
-* @date 17-May-2015
-* @brief Configuration parameters
-******************************************************************************
-* @attention
-*
-* <h2><center>© COPYRIGHT(c) 2014 STMicroelectronics</center></h2>
-*
-* Redistribution and use in source and binary forms, with or without modification,
-* are permitted provided that the following conditions are met:
-* 1. Redistributions of source code must retain the above copyright notice,
-* this list of conditions and the following disclaimer.
-* 2. Redistributions in binary form must reproduce the above copyright notice,
-* this list of conditions and the following disclaimer in the documentation
-* and/or other materials provided with the distribution.
-* 3. Neither the name of STMicroelectronics nor the names of its contributors
-* may be used to endorse or promote products derived from this software
-* without specific prior written permission.
-*
-* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
-* AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
-* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
-* DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
-* FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
-* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
-* SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
-* CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
-* OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
-* OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
-*
-******************************************************************************
-*/
-/*---------------------------------------------------------------------------*/
-/**
- * \addtogroup stm32nucleo-spirit1
- * @{
- *
- * \defgroup stm32nucleo-spirit1-peripherals User Button on STM32 Nucleo
- *
- * Defines some of the platforms capabilities
- * @{
- *
- * \file
- * Header file for the stm32nucleo-spirit1 platform configuration
- */
-/*---------------------------------------------------------------------------*/
-#ifndef __PLATFORM_CONF_H__
-#define __PLATFORM_CONF_H__
-/*---------------------------------------------------------------------------*/
-#ifdef USE_STM32L1XX_NUCLEO
-#include <inttypes.h>
-#include <string.h>
-/*---------------------------------------------------------------------------*/
-#define PLATFORM_HAS_LEDS 1
-#define PLATFORM_HAS_BUTTON 1
-#define PLATFORM_HAS_RADIO 1
-
-#define LEDS_GREEN 1 /*Nucleo LED*/
-#define LEDS_RED 2 /*SPIRIT1 LED*/
-
-#ifdef COMPILE_SENSORS
-#define LEDS_CONF_ALL 1 /*Can't use SPIRIT1 LED in this case*/
-#else
-#define LEDS_CONF_ALL 3 /*No sensors -> we can use SPIRIT1 LED in this case*/
-#endif /*COMPILE_SENSORS*/
-/*---------------------------------------------------------------------------*/
-#define F_CPU 32000000ul
-#define RTIMER_ARCH_SECOND 32768
-#define PRESCALER ((F_CPU / (RTIMER_ARCH_SECOND*2)))
-
-#define UART1_CONF_TX_WITH_INTERRUPT 0
-#define WITH_SERIAL_LINE_INPUT 1
-#define TELNETD_CONF_NUMLINES 6
-#define NETSTACK_CONF_RADIO spirit_radio_driver
-#define NETSTACK_RADIO_MAX_PAYLOAD_LEN 96 /* spirit1-config.h */
-
-#if WITH_IP64
-#include "ip64-conf.h"
-#define WITH_SLIP 1
-#ifndef UIP_FALLBACK_INTERFACE
-#define UIP_FALLBACK_INTERFACE ip64_uip_fallback_interface
-#endif
-#endif /* WITH_IP64 */
-
-/*---------------------------------------------------------------------------*/
-/* define ticks/second for slow and fast clocks. Notice that these should be a
- power of two, eg 64,128,256,512 etc, for efficiency as POT's can be optimized
- well. */
-#define CLOCK_CONF_SECOND 128
-#define RELOAD_VALUE ((F_CPU/CLOCK_CONF_SECOND) - 1)
-/* One tick: 62.5 ms */
-
-#define RTIMER_CLOCK_LT(a,b) ((signed short)((a)-(b)) < 0)
-/*---------------------------------------------------------------------------*/
-typedef unsigned long clock_time_t;
-typedef unsigned long long rtimer_clock_t;
-/*---------------------------------------------------------------------------*/
-#define CC_CONF_REGISTER_ARGS 0
-#define CC_CONF_FUNCTION_POINTER_ARGS 1
-#define CC_CONF_FASTCALL
-#define CC_CONF_VA_ARGS 1
-#define CC_CONF_INLINE inline
-
-#define CCIF
-#define CLIF
-/*---------------------------------------------------------------------------*/
-typedef uint8_t u8_t;
-typedef uint16_t u16_t;
-typedef uint32_t u32_t;
-typedef int32_t s32_t;
-typedef unsigned short uip_stats_t;
-/*---------------------------------------------------------------------------*/
-#define MULTICHAN_CONF_SET_CHANNEL(x)
-#define MULTICHAN_CONF_READ_RSSI(x) 0
-/*---------------------------------------------------------------------------*/
-#endif//USE_STM32L1XX_NUCLEO
-
-#ifdef USE_STM32F4XX_NUCLEO
-#include <inttypes.h>
-#include <string.h>
-#include "main.h"
-/*---------------------------------------------------------------------------*/
-#define PLATFORM_HAS_LEDS 1
-#define PLATFORM_HAS_BUTTON 1
-#define PLATFORM_HAS_RADIO 1
-
-#define LEDS_GREEN 1 /*Nucleo LED*/
-#define LEDS_RED 2 /*SPIRIT1 LED*/
-
-#ifdef COMPILE_SENSORS
-#define LEDS_CONF_ALL 1 /*Can't use SPIRIT1 LED in this case*/
-#else
-#define LEDS_CONF_ALL 3 /*No sensors -> we can use SPIRIT1 LED in this case*/
-#endif /*COMPILE_SENSORS*/
-/*---------------------------------------------------------------------------*/
-#define F_CPU 84000000ul
-#define RTIMER_ARCH_SECOND 96000//32678
-//#define PRESCALER uwPrescalerValue
-
-#define UART1_CONF_TX_WITH_INTERRUPT 0
-#define WITH_SERIAL_LINE_INPUT 1
-#define TELNETD_CONF_NUMLINES 6
-#define NETSTACK_CONF_RADIO spirit_radio_driver
-#define NETSTACK_RADIO_MAX_PAYLOAD_LEN 96 /* spirit1-config.h */
-
-#if WITH_IP64
-#include "ip64-conf.h"
-#define WITH_SLIP 1
-#ifndef UIP_FALLBACK_INTERFACE
-#define UIP_FALLBACK_INTERFACE ip64_uip_fallback_interface
-#endif
-#endif /* WITH_IP64 */
-
-/*---------------------------------------------------------------------------*/
-/* define ticks/second for slow and fast clocks. Notice that these should be a
- power of two, eg 64,128,256,512 etc, for efficiency as POT's can be optimized
- well. */
-#define CLOCK_CONF_SECOND 512
-#define RELOAD_VALUE ((F_CPU/CLOCK_CONF_SECOND) - 1)
-
-/* One tick: 62.5 ms */
-
-#define RTIMER_CLOCK_LT(a,b) ((signed short)((a)-(b)) < 0)
-/*---------------------------------------------------------------------------*/
-typedef unsigned long clock_time_t;
-typedef unsigned long long rtimer_clock_t;
-/*---------------------------------------------------------------------------*/
-#define CC_CONF_REGISTER_ARGS 0
-#define CC_CONF_FUNCTION_POINTER_ARGS 1
-#define CC_CONF_FASTCALL
-#define CC_CONF_VA_ARGS 1
-#define CC_CONF_INLINE inline
-
-#define CCIF
-#define CLIF
-/*---------------------------------------------------------------------------*/
-typedef uint8_t u8_t;
-typedef uint16_t u16_t;
-typedef uint32_t u32_t;
-typedef int32_t s32_t;
-typedef unsigned short uip_stats_t;
-/*---------------------------------------------------------------------------*/
-#define MULTICHAN_CONF_SET_CHANNEL(x)
-#define MULTICHAN_CONF_READ_RSSI(x) 0
-/*---------------------------------------------------------------------------*/
-#endif//USE_STM32F4XX_NUCLEO
-
-#endif /* __PLATFORM_CONF_H__ */
-/*---------------------------------------------------------------------------*/
-/**
- * @}
- * @}
- */
X-NUCLEO-IDS01A4 Sub-1GHz RF Expansion Board