ST / stm-spirit1-rf-driver

Prototype RF driver for STM Sub-1 GHz RF expansion board based on the SPSGRF-868 module for STM32 Nucleo.

Prototype RF Driver for STM Sub-1 GHz RF Expansion Boards based on the SPSGRF-868 and SPSGRF-915 Modules for STM32 Nucleo

Currently supported boards:

Note, in order to use expansion board X-NUCLEO-IDS01A4 in mbed you need to perform the following HW modifications on the board:

  • Unmount resistor R4
  • Mount resistor R7

Furthermore, on some Nucleo development boards (e.g. the NUCLEO_F429ZI), in order to be able to use Ethernet together with these Sub-1 GHz RF expansion boards, you need to compile this driver with macro SPIRIT1_SPI_MOSI=PB_5 defined, while the development board typically requires some HW modification as e.g. described here!

This driver can be used together with the 6LoWPAN stack (a.k.a. Nanostack).

Diff: libs/Contiki_STM32_Library/spirit1-config.h

Revision:
0:4fb29d9ee571
Child:
5:c9c5bc673c64
--- /dev/null	Thu Jan 01 00:00:00 1970 +0000
+++ b/libs/Contiki_STM32_Library/spirit1-config.h	Thu Oct 13 15:41:39 2016 +0200
@@ -0,0 +1,59 @@
+/*
+ * Copyright (c) 2012, STMicroelectronics.
+ * All rights reserved.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ *    notice, this list of conditions and the following disclaimer in the
+ *    documentation and/or other materials provided with the distribution.
+ * 3. Neither the name of the Institute nor the names of its contributors
+ *    may be used to endorse or promote products derived from this software
+ *    without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE INSTITUTE AND CONTRIBUTORS ``AS IS'' AND
+ * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
+ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
+ * ARE DISCLAIMED.  IN NO EVENT SHALL THE INSTITUTE OR CONTRIBUTORS BE LIABLE
+ * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
+ * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
+ * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
+ * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
+ * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
+ * SUCH DAMAGE.
+ *
+ * This file is part of the Contiki operating system.
+ *
+ */
+/*---------------------------------------------------------------------------*/
+#ifndef __SPIRIT1_CONFIG_H__
+#define __SPIRIT1_CONFIG_H__
+/*---------------------------------------------------------------------------*/
+#include "radio.h"
+#include "SPIRIT_Config.h"
+#include "spirit1-const.h"
+/*---------------------------------------------------------------------------*/
+#define CCA_THRESHOLD               -98.0   /* dBm */
+#define XTAL_FREQUENCY              50000000    /* Hz */ 
+#define SPIRIT_MAX_FIFO_LEN         600
+/*---------------------------------------------------------------------------*/
+
+/**    
+ * The MAX_PACKET_LEN is an arbitrary value used to define the two array
+ * spirit_txbuf and spirit_rxbuf.
+ * The SPIRIT1 supports with its packet handler a length of 65,535 bytes,
+ * and in direct mode (without packet handler) there is no limit of data.
+ */  
+#define MAX_PACKET_LEN              SPIRIT_MAX_FIFO_LEN
+/*---------------------------------------------------------------------------*/
+/**    
+ * Spirit1 IC version
+ */
+#define SPIRIT1_VERSION             SPIRIT_VERSION_3_0
+/*---------------------------------------------------------------------------*/
+#endif /* __SPIRIT1_CONFIG_H__ */
+/*---------------------------------------------------------------------------*/