ST / stm-spirit1-rf-driver

Prototype RF driver for STM Sub-1 GHz RF expansion board based on the SPSGRF-868 module for STM32 Nucleo.

Prototype RF Driver for STM Sub-1 GHz RF Expansion Boards based on the SPSGRF-868 and SPSGRF-915 Modules for STM32 Nucleo

Currently supported boards:

Note, in order to use expansion board X-NUCLEO-IDS01A4 in mbed you need to perform the following HW modifications on the board:

  • Unmount resistor R4
  • Mount resistor R7

Furthermore, on some Nucleo development boards (e.g. the NUCLEO_F429ZI), in order to be able to use Ethernet together with these Sub-1 GHz RF expansion boards, you need to compile this driver with macro SPIRIT1_SPI_MOSI=PB_5 defined, while the development board typically requires some HW modification as e.g. described here!

This driver can be used together with the 6LoWPAN stack (a.k.a. Nanostack).

Diff: source/libs/spirit1/X-NUCLEO-IDS01Ax/radio_gpio.h

Revision:
67:93bec0baf1de
Parent:
34:edda6a7238ec
diff -r 1e09d233280b -r 93bec0baf1de source/libs/spirit1/X-NUCLEO-IDS01Ax/radio_gpio.h
--- a/source/libs/spirit1/X-NUCLEO-IDS01Ax/radio_gpio.h	Wed Jul 05 14:02:16 2017 +0200
+++ b/source/libs/spirit1/X-NUCLEO-IDS01Ax/radio_gpio.h	Thu Jul 06 11:13:31 2017 +0200
@@ -1,224 +1,224 @@
-/**
-******************************************************************************
-* @file    radio_gpio.h
-* @author  System Lab - NOIDA
-* @version V1.0.0
-* @date    15-May-2014
-* @brief   This file contains all the functions prototypes for the gpio  
-******************************************************************************
-* @attention
-*
-* <h2><center>&copy; COPYRIGHT(c) 2014 STMicroelectronics</center></h2>
-*
-* Redistribution and use in source and binary forms, with or without modification,
-* are permitted provided that the following conditions are met:
-*   1. Redistributions of source code must retain the above copyright notice,
-*      this list of conditions and the following disclaimer.
-*   2. Redistributions in binary form must reproduce the above copyright notice,
-*      this list of conditions and the following disclaimer in the documentation
-*      and/or other materials provided with the distribution.
-*   3. Neither the name of STMicroelectronics nor the names of its contributors
-*      may be used to endorse or promote products derived from this software
-*      without specific prior written permission.
-*
-* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
-* AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
-* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
-* DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
-* FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
-* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
-* SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
-* CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
-* OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
-* OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
-*
-******************************************************************************
-*/
-/* Exported types ------------------------------------------------------------*/
-/* Exported constants --------------------------------------------------------*/
-/* Exported macro ------------------------------------------------------------*/
-/* Exported Variables ------------------------------------------------------------*/
-/* Exported functions ------------------------------------------------------- */
-
-/* Define to prevent recursive inclusion -------------------------------------*/
-#ifndef __RADIO_GPIO_H
-#define __RADIO_GPIO_H
-#ifdef __cplusplus
-extern "C" {
-#endif
-  
-/* Includes ------------------------------------------------------------------*/
-#ifdef USE_STM32L1XX_NUCLEO
-#include "stm32l1xx_hal.h"
-#endif
-
-#ifdef USE_STM32F4XX_NUCLEO
-#include "stm32f4xx_hal.h"
-#endif
-#include "SPIRIT_Types.h"
-  
-/**
- * @addtogroup BSP
- * @{
- */
-
-
-/* Exported types ------------------------------------------------------------*/
-  /* MCU GPIO pin working mode for GPIO */
-typedef enum                                                                                          
-{
-    RADIO_MODE_GPIO_IN  = 0x00,   /*!< Work as GPIO input */
-    RADIO_MODE_EXTI_IN,           /*!< Work as EXTI */
-    RADIO_MODE_GPIO_OUT,          /*!< Work as GPIO output */
-}RadioGpioMode;  
-
- /* MCU GPIO pin enumeration for GPIO */
-typedef enum 
-{
-  RADIO_GPIO_0     = 0x00, /*!< GPIO_0 selected */
-  RADIO_GPIO_1     = 0x01, /*!< GPIO_1 selected */
-  RADIO_GPIO_2     = 0x02, /*!< GPIO_2 selected */
-  RADIO_GPIO_3     = 0x03, /*!< GPIO_3 selected */
-  RADIO_GPIO_SDN   = 0x04, /*!< GPIO_SDN selected */
-} 
-RadioGpioPin;   
-
-  
-/* Exported constants --------------------------------------------------------*/
-  
-  
-/* Exported macro ------------------------------------------------------------*/
- /* MCU GPIO pin working mode for GPIO */
-#define IS_RADIO_GPIO_MODE(MODE) (((MODE) == RADIO_MODE_GPIO_IN) || \
-                               ((MODE) == RADIO_MODE_EXTI_IN) || \
-                               ((MODE) == RADIO_MODE_GPIO_OUT))
-
-/* Number of Arduino pins used for RADIO GPIO interface */
-#define RADIO_GPIO_NUMBER    ((uint8_t)5)
-
-/* MCU GPIO pin enumeration for GPIO */
-#define IS_RADIO_GPIO_PIN(PIN)   (((PIN) == RADIO_GPIO_0) || \
-                               ((PIN) == RADIO_GPIO_1) || \
-                               ((PIN) == RADIO_GPIO_2) || \
-                               ((PIN) == RADIO_GPIO_3) || \
-                               ((PIN) == RADIO_GPIO_SDN))
-
-/* Define for RADIO board */
-#if !defined (USE_SPIRIT1_DEFAULT)
- #define USE_SPIRIT1_DEFAULT
-#endif  
-
-/* @defgroup Radio_Gpio_config_Define */
-/*NOTE: GPIO0, GPIO1, GPIO2 of SPIRIT1 is not used in the shield*/
-
-#define RADIO_GPIO_0_PORT                          GPIOC
-#define RADIO_GPIO_0_PIN                           GPIO_PIN_1
-#define RADIO_GPIO_0_CLOCK_ENABLE()                __GPIOC_CLK_ENABLE()
-#define RADIO_GPIO_0_CLOCK_DISABLE()               __GPIOC_CLK_ENABLE()   
-#define RADIO_GPIO_0_SPEED                         GPIO_SPEED_HIGH
-#define RADIO_GPIO_0_PUPD                          GPIO_NOPULL
-#define RADIO_GPIO_0_EXTI_LINE                     GPIO_PIN_1
-#define RADIO_GPIO_0_EXTI_MODE                     GPIO_MODE_IT_FALLING
-#define RADIO_GPIO_0_EXTI_IRQN                     EXTI1_IRQn 
-#define RADIO_GPIO_0_EXTI_PREEMPTION_PRIORITY      2
-#define RADIO_GPIO_0_EXTI_SUB_PRIORITY             2
-#define RADIO_GPIO_0_EXTI_IRQ_HANDLER              EXTI1_IRQHandler
-
-#define RADIO_GPIO_1_PORT                          GPIOB
-#define RADIO_GPIO_1_PIN                           GPIO_PIN_0
-#define RADIO_GPIO_1_CLOCK_ENABLE()                __GPIOB_CLK_ENABLE()
-#define RADIO_GPIO_1_CLOCK_DISABLE()               __GPIOB_CLK_ENABLE()   
-#define RADIO_GPIO_1_SPEED                         GPIO_SPEED_HIGH
-#define RADIO_GPIO_1_PUPD                          GPIO_NOPULL
-#define RADIO_GPIO_1_EXTI_LINE                     GPIO_PIN_0
-#define RADIO_GPIO_1_EXTI_MODE                     GPIO_MODE_IT_FALLING
-#define RADIO_GPIO_1_EXTI_IRQN                     EXTI0_IRQn 
-#define RADIO_GPIO_1_EXTI_PREEMPTION_PRIORITY      2
-#define RADIO_GPIO_1_EXTI_SUB_PRIORITY             2
-#define RADIO_GPIO_1_EXTI_IRQ_HANDLER              EXTI0_IRQHandler
-
-#define RADIO_GPIO_2_PORT                          GPIOA
-#define RADIO_GPIO_2_PIN                           GPIO_PIN_4
-#define RADIO_GPIO_2_CLOCK_ENABLE()                __GPIOA_CLK_ENABLE()
-#define RADIO_GPIO_2_CLOCK_DISABLE()               __GPIOA_CLK_ENABLE()   
-#define RADIO_GPIO_2_SPEED                         GPIO_SPEED_HIGH
-#define RADIO_GPIO_2_PUPD                          GPIO_NOPULL
-#define RADIO_GPIO_2_EXTI_LINE                     GPIO_PIN_4
-#define RADIO_GPIO_2_EXTI_MODE                     GPIO_MODE_IT_FALLING
-#define RADIO_GPIO_2_EXTI_IRQN                     EXTI4_IRQn 
-#define RADIO_GPIO_2_EXTI_PREEMPTION_PRIORITY      2
-#define RADIO_GPIO_2_EXTI_SUB_PRIORITY             2
-#define RADIO_GPIO_2_EXTI_IRQ_HANDLER              EXTI4_IRQHandler
-
-
-#if defined (USE_SPIRIT1_DEFAULT)
-
-
-#define RADIO_GPIO_3_PORT                          GPIOC
-#define RADIO_GPIO_3_PIN                           GPIO_PIN_7
-#define RADIO_GPIO_3_CLOCK_ENABLE()              __GPIOC_CLK_ENABLE()
-#define RADIO_GPIO_3_CLOCK_DISABLE()             __GPIOC_CLK_DISABLE()   
-#define RADIO_GPIO_3_SPEED                         GPIO_SPEED_HIGH
-#define RADIO_GPIO_3_PUPD                          GPIO_NOPULL
-#define RADIO_GPIO_3_EXTI_LINE                     GPIO_PIN_7
-#define RADIO_GPIO_3_EXTI_MODE                     GPIO_MODE_IT_FALLING
-#define RADIO_GPIO_3_EXTI_IRQN                     EXTI9_5_IRQn 
-#define RADIO_GPIO_3_EXTI_PREEMPTION_PRIORITY      2
-#define RADIO_GPIO_3_EXTI_SUB_PRIORITY             2
-#define RADIO_GPIO_3_EXTI_IRQ_HANDLER              EXTI9_5_IRQHandler
-
-#else
-
-#define RADIO_GPIO_3_PORT                        GPIOA
-#define RADIO_GPIO_3_PIN                         GPIO_PIN_0
-#define RADIO_GPIO_3_CLOCK_ENABLE()                __GPIOA_CLK_ENABLE()
-#define RADIO_GPIO_3_CLOCK_DISABLE()               __GPIOA_CLK_DISABLE() 
-#define RADIO_GPIO_3_SPEED                       GPIO_SPEED_HIGH
-#define RADIO_GPIO_3_PUPD                        GPIO_NOPULL
-#define RADIO_GPIO_3_EXTI_LINE                   GPIO_PIN_0
-#define RADIO_GPIO_3_EXTI_MODE                   GPIO_MODE_IT_FALLING
-#define RADIO_GPIO_3_EXTI_IRQN                   EXTI0_IRQn
-#define RADIO_GPIO_3_EXTI_PREEMPTION_PRIORITY    2
-#define RADIO_GPIO_3_EXTI_SUB_PRIORITY           2
-#define RADIO_GPIO_3_EXTI_IRQ_HANDLER            EXTI0_IRQHandler
-
-#endif
-
-#define RADIO_GPIO_SDN_PORT                        GPIOA
-#define RADIO_GPIO_SDN_PIN                         GPIO_PIN_10
-#define RADIO_GPIO_SDN_CLOCK_ENABLE()            __GPIOA_CLK_ENABLE()
-#define RADIO_GPIO_SDN_CLOCK_DISABLE()           __GPIOA_CLK_DISABLE()
-#define RADIO_GPIO_SDN_SPEED                       GPIO_SPEED_HIGH
-#define RADIO_GPIO_SDN_PUPD                        GPIO_PULLUP
-
-
-#define RADIO_GPIO_IRQ		RADIO_GPIO_3
-#define SPIRIT_GPIO_IRQ         SPIRIT_GPIO_3
-
-/* Exported Variables ------------------------------------------------------------*/
-  
-  
-/* Exported functions ------------------------------------------------------- */
-FlagStatus RadioGpioGetLevel(RadioGpioPin xGpio);
-void RadioGpioSetLevel(RadioGpioPin xGpio, GPIO_PinState xState);
-void SdkEvalEnterShutdown(void);
-void SdkEvalExitShutdown(void);
-SpiritFlagStatus SdkEvalCheckShutdown(void);
-void RadioGpioInit(RadioGpioPin xGpio, RadioGpioMode xGpioMode);
-void RadioGpioInterruptCmd(RadioGpioPin xGpio, uint8_t nPreemption, uint8_t nSubpriority, FunctionalState xNewState);
-
-
-#ifdef __cplusplus
-}
-#endif
-#endif /*__RADIO_GPIO_H */
-
-/**
-* @}
-*/
-
-/**
-* @}
-*/
-
-/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
+/**
+******************************************************************************
+* @file    radio_gpio.h
+* @author  System Lab - NOIDA
+* @version V1.0.0
+* @date    15-May-2014
+* @brief   This file contains all the functions prototypes for the gpio  
+******************************************************************************
+* @attention
+*
+* <h2><center>&copy; COPYRIGHT(c) 2014 STMicroelectronics</center></h2>
+*
+* Redistribution and use in source and binary forms, with or without modification,
+* are permitted provided that the following conditions are met:
+*   1. Redistributions of source code must retain the above copyright notice,
+*      this list of conditions and the following disclaimer.
+*   2. Redistributions in binary form must reproduce the above copyright notice,
+*      this list of conditions and the following disclaimer in the documentation
+*      and/or other materials provided with the distribution.
+*   3. Neither the name of STMicroelectronics nor the names of its contributors
+*      may be used to endorse or promote products derived from this software
+*      without specific prior written permission.
+*
+* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
+* AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
+* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+* DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
+* FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
+* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
+* SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
+* CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
+* OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+* OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+*
+******************************************************************************
+*/
+/* Exported types ------------------------------------------------------------*/
+/* Exported constants --------------------------------------------------------*/
+/* Exported macro ------------------------------------------------------------*/
+/* Exported Variables ------------------------------------------------------------*/
+/* Exported functions ------------------------------------------------------- */
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef __RADIO_GPIO_H
+#define __RADIO_GPIO_H
+#ifdef __cplusplus
+extern "C" {
+#endif
+  
+/* Includes ------------------------------------------------------------------*/
+#ifdef USE_STM32L1XX_NUCLEO
+#include "stm32l1xx_hal.h"
+#endif
+
+#ifdef USE_STM32F4XX_NUCLEO
+#include "stm32f4xx_hal.h"
+#endif
+#include "SPIRIT_Types.h"
+  
+/**
+ * @addtogroup BSP
+ * @{
+ */
+
+
+/* Exported types ------------------------------------------------------------*/
+  /* MCU GPIO pin working mode for GPIO */
+typedef enum                                                                                          
+{
+    RADIO_MODE_GPIO_IN  = 0x00,   /*!< Work as GPIO input */
+    RADIO_MODE_EXTI_IN,           /*!< Work as EXTI */
+    RADIO_MODE_GPIO_OUT,          /*!< Work as GPIO output */
+}RadioGpioMode;  
+
+ /* MCU GPIO pin enumeration for GPIO */
+typedef enum 
+{
+  RADIO_GPIO_0     = 0x00, /*!< GPIO_0 selected */
+  RADIO_GPIO_1     = 0x01, /*!< GPIO_1 selected */
+  RADIO_GPIO_2     = 0x02, /*!< GPIO_2 selected */
+  RADIO_GPIO_3     = 0x03, /*!< GPIO_3 selected */
+  RADIO_GPIO_SDN   = 0x04, /*!< GPIO_SDN selected */
+} 
+RadioGpioPin;   
+
+  
+/* Exported constants --------------------------------------------------------*/
+  
+  
+/* Exported macro ------------------------------------------------------------*/
+ /* MCU GPIO pin working mode for GPIO */
+#define IS_RADIO_GPIO_MODE(MODE) (((MODE) == RADIO_MODE_GPIO_IN) || \
+                               ((MODE) == RADIO_MODE_EXTI_IN) || \
+                               ((MODE) == RADIO_MODE_GPIO_OUT))
+
+/* Number of Arduino pins used for RADIO GPIO interface */
+#define RADIO_GPIO_NUMBER    ((uint8_t)5)
+
+/* MCU GPIO pin enumeration for GPIO */
+#define IS_RADIO_GPIO_PIN(PIN)   (((PIN) == RADIO_GPIO_0) || \
+                               ((PIN) == RADIO_GPIO_1) || \
+                               ((PIN) == RADIO_GPIO_2) || \
+                               ((PIN) == RADIO_GPIO_3) || \
+                               ((PIN) == RADIO_GPIO_SDN))
+
+/* Define for RADIO board */
+#if !defined (USE_SPIRIT1_DEFAULT)
+ #define USE_SPIRIT1_DEFAULT
+#endif  
+
+/* @defgroup Radio_Gpio_config_Define */
+/*NOTE: GPIO0, GPIO1, GPIO2 of SPIRIT1 is not used in the shield*/
+
+#define RADIO_GPIO_0_PORT                          GPIOC
+#define RADIO_GPIO_0_PIN                           GPIO_PIN_1
+#define RADIO_GPIO_0_CLOCK_ENABLE()                __GPIOC_CLK_ENABLE()
+#define RADIO_GPIO_0_CLOCK_DISABLE()               __GPIOC_CLK_ENABLE()   
+#define RADIO_GPIO_0_SPEED                         GPIO_SPEED_HIGH
+#define RADIO_GPIO_0_PUPD                          GPIO_NOPULL
+#define RADIO_GPIO_0_EXTI_LINE                     GPIO_PIN_1
+#define RADIO_GPIO_0_EXTI_MODE                     GPIO_MODE_IT_FALLING
+#define RADIO_GPIO_0_EXTI_IRQN                     EXTI1_IRQn 
+#define RADIO_GPIO_0_EXTI_PREEMPTION_PRIORITY      2
+#define RADIO_GPIO_0_EXTI_SUB_PRIORITY             2
+#define RADIO_GPIO_0_EXTI_IRQ_HANDLER              EXTI1_IRQHandler
+
+#define RADIO_GPIO_1_PORT                          GPIOB
+#define RADIO_GPIO_1_PIN                           GPIO_PIN_0
+#define RADIO_GPIO_1_CLOCK_ENABLE()                __GPIOB_CLK_ENABLE()
+#define RADIO_GPIO_1_CLOCK_DISABLE()               __GPIOB_CLK_ENABLE()   
+#define RADIO_GPIO_1_SPEED                         GPIO_SPEED_HIGH
+#define RADIO_GPIO_1_PUPD                          GPIO_NOPULL
+#define RADIO_GPIO_1_EXTI_LINE                     GPIO_PIN_0
+#define RADIO_GPIO_1_EXTI_MODE                     GPIO_MODE_IT_FALLING
+#define RADIO_GPIO_1_EXTI_IRQN                     EXTI0_IRQn 
+#define RADIO_GPIO_1_EXTI_PREEMPTION_PRIORITY      2
+#define RADIO_GPIO_1_EXTI_SUB_PRIORITY             2
+#define RADIO_GPIO_1_EXTI_IRQ_HANDLER              EXTI0_IRQHandler
+
+#define RADIO_GPIO_2_PORT                          GPIOA
+#define RADIO_GPIO_2_PIN                           GPIO_PIN_4
+#define RADIO_GPIO_2_CLOCK_ENABLE()                __GPIOA_CLK_ENABLE()
+#define RADIO_GPIO_2_CLOCK_DISABLE()               __GPIOA_CLK_ENABLE()   
+#define RADIO_GPIO_2_SPEED                         GPIO_SPEED_HIGH
+#define RADIO_GPIO_2_PUPD                          GPIO_NOPULL
+#define RADIO_GPIO_2_EXTI_LINE                     GPIO_PIN_4
+#define RADIO_GPIO_2_EXTI_MODE                     GPIO_MODE_IT_FALLING
+#define RADIO_GPIO_2_EXTI_IRQN                     EXTI4_IRQn 
+#define RADIO_GPIO_2_EXTI_PREEMPTION_PRIORITY      2
+#define RADIO_GPIO_2_EXTI_SUB_PRIORITY             2
+#define RADIO_GPIO_2_EXTI_IRQ_HANDLER              EXTI4_IRQHandler
+
+
+#if defined (USE_SPIRIT1_DEFAULT)
+
+
+#define RADIO_GPIO_3_PORT                          GPIOC
+#define RADIO_GPIO_3_PIN                           GPIO_PIN_7
+#define RADIO_GPIO_3_CLOCK_ENABLE()              __GPIOC_CLK_ENABLE()
+#define RADIO_GPIO_3_CLOCK_DISABLE()             __GPIOC_CLK_DISABLE()   
+#define RADIO_GPIO_3_SPEED                         GPIO_SPEED_HIGH
+#define RADIO_GPIO_3_PUPD                          GPIO_NOPULL
+#define RADIO_GPIO_3_EXTI_LINE                     GPIO_PIN_7
+#define RADIO_GPIO_3_EXTI_MODE                     GPIO_MODE_IT_FALLING
+#define RADIO_GPIO_3_EXTI_IRQN                     EXTI9_5_IRQn 
+#define RADIO_GPIO_3_EXTI_PREEMPTION_PRIORITY      2
+#define RADIO_GPIO_3_EXTI_SUB_PRIORITY             2
+#define RADIO_GPIO_3_EXTI_IRQ_HANDLER              EXTI9_5_IRQHandler
+
+#else
+
+#define RADIO_GPIO_3_PORT                        GPIOA
+#define RADIO_GPIO_3_PIN                         GPIO_PIN_0
+#define RADIO_GPIO_3_CLOCK_ENABLE()                __GPIOA_CLK_ENABLE()
+#define RADIO_GPIO_3_CLOCK_DISABLE()               __GPIOA_CLK_DISABLE() 
+#define RADIO_GPIO_3_SPEED                       GPIO_SPEED_HIGH
+#define RADIO_GPIO_3_PUPD                        GPIO_NOPULL
+#define RADIO_GPIO_3_EXTI_LINE                   GPIO_PIN_0
+#define RADIO_GPIO_3_EXTI_MODE                   GPIO_MODE_IT_FALLING
+#define RADIO_GPIO_3_EXTI_IRQN                   EXTI0_IRQn
+#define RADIO_GPIO_3_EXTI_PREEMPTION_PRIORITY    2
+#define RADIO_GPIO_3_EXTI_SUB_PRIORITY           2
+#define RADIO_GPIO_3_EXTI_IRQ_HANDLER            EXTI0_IRQHandler
+
+#endif
+
+#define RADIO_GPIO_SDN_PORT                        GPIOA
+#define RADIO_GPIO_SDN_PIN                         GPIO_PIN_10
+#define RADIO_GPIO_SDN_CLOCK_ENABLE()            __GPIOA_CLK_ENABLE()
+#define RADIO_GPIO_SDN_CLOCK_DISABLE()           __GPIOA_CLK_DISABLE()
+#define RADIO_GPIO_SDN_SPEED                       GPIO_SPEED_HIGH
+#define RADIO_GPIO_SDN_PUPD                        GPIO_PULLUP
+
+
+#define RADIO_GPIO_IRQ		RADIO_GPIO_3
+#define SPIRIT_GPIO_IRQ         SPIRIT_GPIO_3
+
+/* Exported Variables ------------------------------------------------------------*/
+  
+  
+/* Exported functions ------------------------------------------------------- */
+FlagStatus RadioGpioGetLevel(RadioGpioPin xGpio);
+void RadioGpioSetLevel(RadioGpioPin xGpio, GPIO_PinState xState);
+void SdkEvalEnterShutdown(void);
+void SdkEvalExitShutdown(void);
+SpiritFlagStatus SdkEvalCheckShutdown(void);
+void RadioGpioInit(RadioGpioPin xGpio, RadioGpioMode xGpioMode);
+void RadioGpioInterruptCmd(RadioGpioPin xGpio, uint8_t nPreemption, uint8_t nSubpriority, FunctionalState xNewState);
+
+
+#ifdef __cplusplus
+}
+#endif
+#endif /*__RADIO_GPIO_H */
+
+/**
+* @}
+*/
+
+/**
+* @}
+*/
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/