X_NUCLEO_IPS02A1 24V Intelligent Power Switch (IPS) Nucleo Expansion Board Firmware Package

Introduction

This firmware package includes Components Device Drivers and Board Support Package for STMicroelectronics X-NUCLEO-IPS02A1 IPS Expansion Board.

Firmware Library

Class X_NUCLEO_IPS02A1 is intended to represent the Intelligent Power Switch expansion board with the same name.

The expansion board is basically featuring by one IP:

vps2535h vertical power switch.

It is intentionally implemented as a singleton because only one X-NUCLEO-IPS02A1 at a time might be deployed in a HW component stack. In order to get the singleton instance you have to call class method `Instance()`, e.g.:

// IPS expansion board singleton instance
static X_NUCLEO_IPS02A1 *ips_expansion_board = X_NUCLEO_IPS02A1::Instance();

How to use the firmware package

The basic operations to deal with the firmware pkg and use the IPS are the following :

1) instantiate the X_NUCLEO by calling class method `Instance()`:

// Sensors expansion board singleton instance
static X_NUCLEO_IPS02A1 *sensors_expansion_board = X_NUCLEO_IPS02A1::Instance();

2) Switch-on or Switch-off loads output (Channel 1 or Channel 2) by setting or clearing associated digital input :

            ips_expansion_board.vps2535h.Fr_Stby = 1; // set Fr_Stby pin
            ips_expansion_board.vps2535h.In_1 = 1; // switch-on Channel 1
            ips_expansion_board.vps2535h.In_2 = 0; // switch-off Channle 2

3) Read Current circulating on Channel 1 or Channel 2 and print on the Terminal

            Multisense_Signal= ips_expansion_board.GetCurrent(CHANNEL_1);
            printf("Current Ch1 = %2.3fA \n\r", Multisense_Signal);
            Multisense_Signal= ips_expansion_board.GetCurrent(CHANNEL_2);
            printf("Current Ch2 = %2.3fA \n\r", Multisense_Signal);

Components/Interfaces/Component.h

Committer:: Davidroid
Date:: 2017-05-09
Revision:: 7:10e489682b80

File content as of revision 7:10e489682b80:

/**
 ******************************************************************************
 * @file    Component.h
 * @author  AST
 * @version V1.0.0
 * @date    April 13th, 2015
 * @brief   This file contains the abstract class describing the interface of a
 *          generic component.
 ******************************************************************************
 * @attention
 *
 * <h2><center>&copy; COPYRIGHT(c) 2015 STMicroelectronics</center></h2>
 *
 * Redistribution and use in source and binary forms, with or without modification,
 * are permitted provided that the following conditions are met:
 *   1. Redistributions of source code must retain the above copyright notice,
 *      this list of conditions and the following disclaimer.
 *   2. Redistributions in binary form must reproduce the above copyright notice,
 *      this list of conditions and the following disclaimer in the documentation
 *      and/or other materials provided with the distribution.
 *   3. Neither the name of STMicroelectronics nor the names of its contributors
 *      may be used to endorse or promote products derived from this software
 *      without specific prior written permission.
 *
 * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
 * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
 * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
 * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
 * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
 * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
 * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
 * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
 * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
 * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
 *
 ******************************************************************************
 */


/* Define to prevent recursive inclusion -------------------------------------*/

#ifndef __COMPONENT_CLASS_H
#define __COMPONENT_CLASS_H


/* Includes ------------------------------------------------------------------*/

#include <stdint.h>


/* Classes  ------------------------------------------------------------------*/

/**
 * An abstract class for Generic components.
 */
class Component {
public:

    /**
     * @brief     Initializing the component.
     * @param[in] init pointer to device specific initalization structure.
     * @retval    "0" in case of success, an error code otherwise.
     */
    virtual int init(void *init) = 0;

    /**
     * @brief      Getting the ID of the component.
     * @param[out] id pointer to an allocated variable to store the ID into.
     * @retval     "0" in case of success, an error code otherwise.
     */
    virtual int read_id(uint8_t *id) = 0;

    /**
     * @brief Destructor.
     */
    virtual ~Component() {};
};

#endif /* __COMPONENT_CLASS_H */

/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/