Diff: vl53l1x_error_codes.h

Revision:

5:f16727052990

diff -r d25c4fa216af -r f16727052990 vl53l1x_error_codes.h
--- /dev/null	Thu Jan 01 00:00:00 1970 +0000
+++ b/vl53l1x_error_codes.h	Mon Jan 28 10:14:03 2019 +0000
@@ -0,0 +1,251 @@
+/*
+* Copyright (c) 2017, STMicroelectronics - All Rights Reserved
+*
+* This file is part of VL53L1 Core and is dual licensed,
+* either 'STMicroelectronics
+* Proprietary license'
+* or 'BSD 3-clause "New" or "Revised" License' , at your option.
+*
+********************************************************************************
+*
+* 'STMicroelectronics Proprietary license'
+*
+********************************************************************************
+*
+* License terms: STMicroelectronics Proprietary in accordance with licensing
+* terms at www.st.com/sla0081
+*
+* STMicroelectronics confidential
+* Reproduction and Communication of this document is strictly prohibited unless
+* specifically authorized in writing by STMicroelectronics.
+*
+*
+********************************************************************************
+*
+* Alternatively, VL53L1 Core may be distributed under the terms of
+* 'BSD 3-clause "New" or "Revised" License', in which case the following
+* provisions apply instead of the ones mentioned above :
+*
+********************************************************************************
+*
+* License terms: BSD 3-clause "New" or "Revised" License.
+*
+* Redistribution and use in source and binary forms, with or without
+* modification, are permitted provided that the following conditions are met:
+*
+* 1. Redistributions of source code must retain the above copyright notice, this
+* list of conditions and the following disclaimer.
+*
+* 2. Redistributions in binary form must reproduce the above copyright notice,
+* this list of conditions and the following disclaimer in the documentation
+* and/or other materials provided with the distribution.
+*
+* 3. Neither the name of the copyright holder nor the names of its contributors
+* may be used to endorse or promote products derived from this software
+* without specific prior written permission.
+*
+* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
+* AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
+* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+* DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
+* FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
+* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
+* SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
+* CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
+* OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+* OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+*
+*
+********************************************************************************
+*
+*/
+
+/**
+ * @file vl53l1_error_codes.h
+ *
+ * @brief Error Code definitions for VL53L1 API.
+ *
+ */
+
+#ifndef _VL53L1X_ERROR_CODES_H_
+#define _VL53L1X_ERROR_CODES_H_
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+
+/****************************************
+ * PRIVATE define do not edit
+ ****************************************/
+
+/** @defgroup VL53L1_define_Error_group Error and Warning code returned by API
+ *  The following DEFINE are used to identify the PAL ERROR
+ *  @{
+ */
+
+typedef int8_t VL53L1_Error;
+
+#define VL53L1_ERROR_NONE                              ((VL53L1_Error)  0)
+#define VL53L1_ERROR_CALIBRATION_WARNING               ((VL53L1_Error) - 1)
+    /*!< Warning invalid calibration data may be in used
+        \a  VL53L1_InitData()
+        \a VL53L1_GetOffsetCalibrationData
+        \a VL53L1_SetOffsetCalibrationData */
+#define VL53L1_ERROR_MIN_CLIPPED                       ((VL53L1_Error) - 2)
+    /*!< Warning parameter passed was clipped to min before to be applied */
+
+#define VL53L1_ERROR_UNDEFINED                         ((VL53L1_Error) - 3)
+    /*!< Unqualified error */
+#define VL53L1_ERROR_INVALID_PARAMS                    ((VL53L1_Error) - 4)
+    /*!< Parameter passed is invalid or out of range */
+#define VL53L1_ERROR_NOT_SUPPORTED                     ((VL53L1_Error) - 5)
+    /*!< Function is not supported in current mode or configuration */
+#define VL53L1_ERROR_RANGE_ERROR                       ((VL53L1_Error) - 6)
+    /*!< Device report a ranging error interrupt status */
+#define VL53L1_ERROR_TIME_OUT                          ((VL53L1_Error) - 7)
+    /*!< Aborted due to time out */
+#define VL53L1_ERROR_MODE_NOT_SUPPORTED                ((VL53L1_Error) - 8)
+    /*!< Asked mode is not supported by the device */
+#define VL53L1_ERROR_BUFFER_TOO_SMALL                  ((VL53L1_Error) - 9)
+    /*!< ... */
+#define VL53L1_ERROR_COMMS_BUFFER_TOO_SMALL            ((VL53L1_Error) - 10)
+    /*!< Supplied buffer is larger than I2C supports */
+#define VL53L1_ERROR_GPIO_NOT_EXISTING                 ((VL53L1_Error) - 11)
+    /*!< User tried to setup a non-existing GPIO pin */
+#define VL53L1_ERROR_GPIO_FUNCTIONALITY_NOT_SUPPORTED  ((VL53L1_Error) - 12)
+    /*!< unsupported GPIO functionality */
+#define VL53L1_ERROR_CONTROL_INTERFACE                 ((VL53L1_Error) - 13)
+    /*!< error reported from IO functions */
+#define VL53L1_ERROR_INVALID_COMMAND                   ((VL53L1_Error) - 14)
+    /*!< The command is not allowed in the current device state
+     *  (power down) */
+#define VL53L1_ERROR_DIVISION_BY_ZERO                  ((VL53L1_Error) - 15)
+    /*!< In the function a division by zero occurs */
+#define VL53L1_ERROR_REF_SPAD_INIT                     ((VL53L1_Error) - 16)
+    /*!< Error during reference SPAD initialization */
+#define VL53L1_ERROR_GPH_SYNC_CHECK_FAIL               ((VL53L1_Error) - 17)
+    /*!<  GPH sync interrupt check fail - API out of sync with device*/
+#define VL53L1_ERROR_STREAM_COUNT_CHECK_FAIL           ((VL53L1_Error) - 18)
+    /*!<  Stream count check fail - API out of sync with device */
+#define VL53L1_ERROR_GPH_ID_CHECK_FAIL                 ((VL53L1_Error) - 19)
+    /*!<  GPH ID check fail - API out of sync with device */
+#define VL53L1_ERROR_ZONE_STREAM_COUNT_CHECK_FAIL      ((VL53L1_Error) - 20)
+    /*!<  Zone dynamic config stream count check failed - API out of sync */
+#define VL53L1_ERROR_ZONE_GPH_ID_CHECK_FAIL            ((VL53L1_Error) - 21)
+    /*!<  Zone dynamic config GPH ID check failed - API out of sync */
+
+#define VL53L1_ERROR_XTALK_EXTRACTION_NO_SAMPLE_FAIL   ((VL53L1_Error) - 22)
+    /*!<  Thrown when run_xtalk_extraction fn has 0 succesful samples
+     * when using the full array to sample the xtalk. In this case there is
+     * not enough information to generate new Xtalk parm info. The function
+     * will exit and leave the current xtalk parameters unaltered */
+#define VL53L1_ERROR_XTALK_EXTRACTION_SIGMA_LIMIT_FAIL ((VL53L1_Error) - 23)
+    /*!<  Thrown when run_xtalk_extraction fn has found that the
+     * avg sigma estimate of the full array xtalk sample is > than the
+     * maximal limit allowed. In this case the xtalk sample is too noisy for
+     * measurement. The function will exit and leave the current xtalk parameters
+     * unaltered. */
+
+
+#define VL53L1_ERROR_OFFSET_CAL_NO_SAMPLE_FAIL           ((VL53L1_Error) - 24)
+    /*!<  Thrown if there one of stages has no valid offset calibration
+     *    samples. A fatal error calibration not valid */
+#define VL53L1_ERROR_OFFSET_CAL_NO_SPADS_ENABLED_FAIL    ((VL53L1_Error) - 25)
+    /*!<  Thrown if there one of stages has zero effective SPADS
+     *    Traps the case when MM1 SPADs is zero.
+     *    A fatal error calibration not valid */
+#define VL53L1_ERROR_ZONE_CAL_NO_SAMPLE_FAIL             ((VL53L1_Error) - 26)
+    /*!<  Thrown if then some of the zones have no valid samples
+     *    A fatal error calibration not valid */
+
+#define VL53L1_ERROR_TUNING_PARM_KEY_MISMATCH             ((VL53L1_Error) - 27)
+    /*!<  Thrown if the tuning file key table version does not match with
+     * expected value. The driver expects the key table version to match
+     * the compiled default version number in the define
+     * #VL53L1_TUNINGPARM_KEY_TABLE_VERSION_DEFAULT
+     * */
+
+#define VL53L1_WARNING_REF_SPAD_CHAR_NOT_ENOUGH_SPADS   ((VL53L1_Error) - 28)
+    /*!<  Thrown if there are less than 5 good SPADs are available. */
+#define VL53L1_WARNING_REF_SPAD_CHAR_RATE_TOO_HIGH      ((VL53L1_Error) - 29)
+    /*!<  Thrown if the final reference rate is greater than
+          the upper reference rate limit - default is 40 Mcps.
+          Implies a minimum Q3 (x10) SPAD (5) selected */
+#define VL53L1_WARNING_REF_SPAD_CHAR_RATE_TOO_LOW       ((VL53L1_Error) - 30)
+    /*!<  Thrown if the final reference rate is less than
+          the lower reference rate limit - default is 10 Mcps.
+          Implies maximum Q1 (x1) SPADs selected */
+
+
+#define VL53L1_WARNING_OFFSET_CAL_MISSING_SAMPLES       ((VL53L1_Error) - 31)
+    /*!<  Thrown if there is less than the requested number of
+     *    valid samples. */
+#define VL53L1_WARNING_OFFSET_CAL_SIGMA_TOO_HIGH        ((VL53L1_Error) - 32)
+    /*!<  Thrown if the offset calibration range sigma estimate is greater
+     *    than 8.0 mm. This is the recommended min value to yield a stable
+     *    offset measurement */
+#define VL53L1_WARNING_OFFSET_CAL_RATE_TOO_HIGH         ((VL53L1_Error) - 33)
+    /*!< Thrown when VL53L1_run_offset_calibration()  peak rate is greater
+         than that 50.0Mcps. This is the recommended  max rate to avoid
+         pile-up influencing the offset measurement */
+#define VL53L1_WARNING_OFFSET_CAL_SPAD_COUNT_TOO_LOW    ((VL53L1_Error) - 34)
+    /*!< Thrown when VL53L1_run_offset_calibration() when one of stages
+         range has less that 5.0 effective SPADS. This is the recommended
+         min value to yield a stable offset */
+
+
+#define VL53L1_WARNING_ZONE_CAL_MISSING_SAMPLES       ((VL53L1_Error) - 35)
+    /*!<  Thrown if one of more of the zones have less than
+          the requested number of valid samples */
+#define VL53L1_WARNING_ZONE_CAL_SIGMA_TOO_HIGH        ((VL53L1_Error) - 36)
+    /*!<  Thrown if one or more zones have sigma estimate value greater
+     *    than 8.0 mm. This is the recommended min value to yield a stable
+     *    offset measurement */
+#define VL53L1_WARNING_ZONE_CAL_RATE_TOO_HIGH         ((VL53L1_Error) - 37)
+    /*!< Thrown if one of more zones have  peak rate higher than
+          that 50.0Mcps. This is the recommended  max rate to avoid
+         pile-up influencing the offset measurement */
+
+
+#define VL53L1_WARNING_XTALK_MISSING_SAMPLES             ((VL53L1_Error) - 38)
+    /*!< Thrown to notify that some of the xtalk samples did not yield
+     * valid ranging pulse data while attempting to measure
+     * the xtalk signal in vl53l1_run_xtalk_extract(). This can signify any of
+     * the zones are missing samples, for further debug information the
+     * xtalk_results struct should be referred to. This warning is for
+     * notification only, the xtalk pulse and shape have still been generated
+     */
+#define VL53L1_WARNING_XTALK_NO_SAMPLES_FOR_GRADIENT     ((VL53L1_Error) - 39)
+    /*!< Thrown to notify that some of teh xtalk samples used for gradient
+     * generation did not yield valid ranging pulse data while attempting to
+     * measure the xtalk signal in vl53l1_run_xtalk_extract(). This can signify
+     * that any one of the zones 0-3 yielded no successful samples. The
+     * xtalk_results struct should be referred to for further debug info.
+     * This warning is for notification only, the xtalk pulse and shape
+     * have still been generated.
+     */
+#define VL53L1_WARNING_XTALK_SIGMA_LIMIT_FOR_GRADIENT    ((VL53L1_Error) - 40)
+/*!< Thrown to notify that some of the xtalk samples used for gradient
+     * generation did not pass the sigma limit check  while attempting to
+     * measure the xtalk signal in vl53l1_run_xtalk_extract(). This can signify
+     * that any one of the zones 0-3 yielded an avg sigma_mm value > the limit.
+     * The xtalk_results struct should be referred to for further debug info.
+     * This warning is for notification only, the xtalk pulse and shape
+     * have still been generated.
+     */
+
+#define VL53L1_ERROR_NOT_IMPLEMENTED                   ((VL53L1_Error) - 41)
+    /*!< Tells requested functionality has not been implemented yet or
+     * not compatible with the device */
+#define VL53L1_ERROR_PLATFORM_SPECIFIC_START           ((VL53L1_Error) - 60)
+    /*!< Tells the starting code for platform */
+/** @} VL53L1_define_Error_group */
+
+
+#ifdef __cplusplus
+}
+#endif
+
+
+#endif /* _VL53L1X_ERROR_CODES_H_ */
\ No newline at end of file