ST
3-axis MEMS ultra low power accelerometer
Dependencies: X_NUCLEO_COMMON ST_INTERFACES
Dependents: X_NUCLEO_IKS01A3 X_NUCLEO_IKS01A3
Diff: lis2dw12_reg.c
- Revision:
- 0:dff8803aace7
- Child:
- 1:94e908301953
diff -r 000000000000 -r dff8803aace7 lis2dw12_reg.c
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/lis2dw12_reg.c Mon Nov 19 13:20:07 2018 +0000
@@ -0,0 +1,2252 @@
+/*
+ ******************************************************************************
+ * @file lis2dw12_reg.c
+ * @author MEMS Software Solution Team
+ * @date 25-January-2018
+ * @brief LIS2DW12 driver file
+ ******************************************************************************
+ * @attention
+ *
+ * <h2><center>© COPYRIGHT(c) 2018 STMicroelectronics</center></h2>
+ *
+ * Redistribution and use in source and binary forms, with or without modification,
+ * are permitted provided that the following conditions are met:
+ * 1. Redistributions of source code must retain the above copyright notice,
+ * this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright notice,
+ * this list of conditions and the following disclaimer in the documentation
+ * and/or other materials provided with the distribution.
+ * 3. Neither the name of STMicroelectronics nor the names of its contributors
+ * may be used to endorse or promote products derived from this software
+ * without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
+ * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
+ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
+ * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
+ * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
+ * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
+ * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
+ * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+ * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ *
+ */
+
+#include "lis2dw12_reg.h"
+
+/**
+ * @addtogroup lis2dw12
+ * @brief This file provides a set of functions needed to drive the
+ * lis2dw12 enanced inertial module.
+ * @{
+ */
+
+/**
+ * @addtogroup interfaces_functions
+ * @brief This section provide a set of functions used to read and write
+ * a generic register of the device.
+ * @{
+ */
+
+/**
+ * @brief Read generic device register
+ *
+ * @param lis2dw12_ctx_t* ctx: read / write interface definitions
+ * @param uint8_t reg: register to read
+ * @param uint8_t* data: pointer to buffer that store the data read
+ * @param uint16_t len: number of consecutive register to read
+ *
+ */
+int32_t lis2dw12_read_reg(lis2dw12_ctx_t* ctx, uint8_t reg, uint8_t* data,
+ uint16_t len)
+{
+ return ctx->read_reg(ctx->handle, reg, data, len);
+}
+
+/**
+ * @brief Write generic device register
+ *
+ * @param lis2dw12_ctx_t *ctx: read / write interface definitions
+ * @param uint8_t reg: register to write
+ * @param uint8_t* data: pointer to data to write in register reg
+ * @param uint16_t len: number of consecutive register to write
+ *
+*/
+int32_t lis2dw12_write_reg(lis2dw12_ctx_t* ctx, uint8_t reg, uint8_t* data,
+ uint16_t len)
+{
+ return ctx->write_reg(ctx->handle, reg, data, len);
+}
+
+/**
+ * @}
+ */
+
+/**
+ * @addtogroup data_generation_c
+ * @brief This section groups all the functions concerning data generation
+ * @{
+ */
+
+/**
+ * @brief power_mode: [set] Select accelerometer operating modes.
+ *
+ * @param lis2dw12_ctx_t *ctx: read / write interface definitions
+ * @param lis2dw12_mode_t: change the values of mode / lp_mode in reg CTRL1
+ * and low_noise in reg CTRL6
+ *
+ */
+int32_t lis2dw12_power_mode_set(lis2dw12_ctx_t *ctx, lis2dw12_mode_t val)
+{
+ lis2dw12_reg_t reg;
+ int32_t mm_error;
+
+ mm_error = lis2dw12_read_reg(ctx, LIS2DW12_CTRL1, ®.byte, 1);
+ reg.ctrl1.mode = ( val & 0x0C ) >> 2;
+ reg.ctrl1.lp_mode = val & 0x03 ;
+ mm_error = lis2dw12_write_reg(ctx, LIS2DW12_CTRL1, ®.byte, 1);
+
+ mm_error = lis2dw12_read_reg(ctx, LIS2DW12_CTRL6, ®.byte, 1);
+ reg.ctrl6.low_noise = ( val & 0x10 ) >> 4;
+ mm_error = lis2dw12_write_reg(ctx, LIS2DW12_CTRL6, ®.byte, 1);
+
+ return mm_error;
+}
+
+/**
+ * @brief power_mode: [get] Select accelerometer operating modes.
+ *
+ * @param lis2dw12_ctx_t *ctx: read / write interface definitions
+ * @param lis2dw12_mode_t: change the values of mode / lp_mode in reg CTRL1
+ * and low_noise in reg CTRL6
+ *
+ */
+int32_t lis2dw12_power_mode_get(lis2dw12_ctx_t *ctx, lis2dw12_mode_t *val)
+{
+ lis2dw12_reg_t reg[2];
+ int32_t mm_error;
+
+ mm_error = lis2dw12_read_reg(ctx, LIS2DW12_CTRL1, ®[0].byte, 1);
+ mm_error = lis2dw12_read_reg(ctx, LIS2DW12_CTRL6, ®[1].byte, 1);
+ *val = (lis2dw12_mode_t) ((reg[1].ctrl6.low_noise << 4) +
+ (reg[0].ctrl1.mode << 2) + reg[0].ctrl1.lp_mode);
+
+ return mm_error;
+}
+
+/**
+ * @brief data_rate: [set] Accelerometer data rate selection.
+ *
+ * @param lis2dw12_ctx_t *ctx: read / write interface definitions
+ * @param lis2dw12_odr_t: change the values of odr in reg CTRL1
+ *
+ */
+int32_t lis2dw12_data_rate_set(lis2dw12_ctx_t *ctx, lis2dw12_odr_t val)
+{
+ lis2dw12_reg_t reg;
+ int32_t mm_error;
+
+ mm_error = lis2dw12_read_reg(ctx, LIS2DW12_CTRL1, ®.byte, 1);
+ reg.ctrl1.odr = val;
+ mm_error = lis2dw12_write_reg(ctx, LIS2DW12_CTRL1, ®.byte, 1);
+
+ mm_error = lis2dw12_read_reg(ctx, LIS2DW12_CTRL3, ®.byte, 1);
+ reg.ctrl3.slp_mode = ( val & 0x30 ) >> 4;
+ mm_error = lis2dw12_write_reg(ctx, LIS2DW12_CTRL3, ®.byte, 1);
+
+ return mm_error;
+}
+
+/**
+ * @brief data_rate: [get] Accelerometer data rate selection.
+ *
+ * @param lis2dw12_ctx_t *ctx: read / write interface definitions
+ * @param lis2dw12_odr_t: Get the values of odr in reg CTRL1
+ *
+ */
+int32_t lis2dw12_data_rate_get(lis2dw12_ctx_t *ctx, lis2dw12_odr_t *val)
+{
+ lis2dw12_reg_t reg[2];
+ int32_t mm_error;
+
+ mm_error = lis2dw12_read_reg(ctx, LIS2DW12_CTRL1, ®[0].byte, 1);
+ mm_error = lis2dw12_read_reg(ctx, LIS2DW12_CTRL3, ®[1].byte, 1);
+ *val = (lis2dw12_odr_t) ((reg[1].ctrl3.slp_mode << 4) + reg[0].ctrl1.odr);
+
+ return mm_error;
+}
+
+/**
+ * @brief block_data_update: [set] Blockdataupdate.
+ *
+ * @param lis2dw12_ctx_t *ctx: read / write interface definitions
+ * @param uint8_t val: change the values of bdu in reg CTRL2
+ *
+ */
+int32_t lis2dw12_block_data_update_set(lis2dw12_ctx_t *ctx, uint8_t val)
+{
+ lis2dw12_reg_t reg;
+ int32_t mm_error;
+
+ mm_error = lis2dw12_read_reg(ctx, LIS2DW12_CTRL2, ®.byte, 1);
+ reg.ctrl2.bdu = val;
+ mm_error = lis2dw12_write_reg(ctx, LIS2DW12_CTRL2, ®.byte, 1);
+
+ return mm_error;
+}
+
+/**
+ * @brief block_data_update: [get] Blockdataupdate.
+ *
+ * @param lis2dw12_ctx_t *ctx: read / write interface definitions
+ * @param uint8_t: change the values of bdu in reg CTRL2
+ *
+ */
+int32_t lis2dw12_block_data_update_get(lis2dw12_ctx_t *ctx, uint8_t *val)
+{
+ lis2dw12_reg_t reg;
+ int32_t mm_error;
+
+ mm_error = lis2dw12_read_reg(ctx, LIS2DW12_CTRL2, ®.byte, 1);
+ *val = reg.ctrl2.bdu;
+
+ return mm_error;
+}
+
+/**
+ * @brief full_scale: [set] Accelerometer full-scale selection.
+ *
+ * @param lis2dw12_ctx_t *ctx: read / write interface definitions
+ * @param lis2dw12_fs_t: change the values of fs in reg CTRL6
+ *
+ */
+int32_t lis2dw12_full_scale_set(lis2dw12_ctx_t *ctx, lis2dw12_fs_t val)
+{
+ lis2dw12_reg_t reg;
+ int32_t mm_error;
+
+ mm_error = lis2dw12_read_reg(ctx, LIS2DW12_CTRL6, ®.byte, 1);
+ reg.ctrl6.fs = val;
+ mm_error = lis2dw12_write_reg(ctx, LIS2DW12_CTRL6, ®.byte, 1);
+
+ return mm_error;
+}
+
+/**
+ * @brief full_scale: [get] Accelerometer full-scale selection.
+ *
+ * @param lis2dw12_ctx_t *ctx: read / write interface definitions
+ * @param lis2dw12_fs_t: Get the values of fs in reg CTRL6
+ *
+ */
+int32_t lis2dw12_full_scale_get(lis2dw12_ctx_t *ctx, lis2dw12_fs_t *val)
+{
+ lis2dw12_reg_t reg;
+ int32_t mm_error;
+
+ mm_error = lis2dw12_read_reg(ctx, LIS2DW12_CTRL6, ®.byte, 1);
+ *val = (lis2dw12_fs_t) reg.ctrl6.fs;
+
+ return mm_error;
+}
+
+/**
+ * @brief status_reg: [get] The STATUS_REG register of the device.
+ *
+ * @param lis2dw12_ctx_t *ctx: read / write interface definitions
+ * @param lis2dw12_: union of registers from STATUS to
+ *
+ */
+int32_t lis2dw12_status_reg_get(lis2dw12_ctx_t *ctx, lis2dw12_status_t *val)
+{
+ return lis2dw12_read_reg(ctx, LIS2DW12_STATUS, (uint8_t*) val, 1);
+}
+/**
+ * @brief flag_data_ready: [get] Accelerometer new data available.
+ *
+ * @param lis2dw12_ctx_t *ctx: read / write interface definitions
+ * @param uint8_t: change the values of drdy in reg STATUS
+ *
+ */
+int32_t lis2dw12_flag_data_ready_get(lis2dw12_ctx_t *ctx, uint8_t *val)
+{
+ lis2dw12_reg_t reg;
+ int32_t mm_error;
+
+ mm_error = lis2dw12_read_reg(ctx, LIS2DW12_STATUS, ®.byte, 1);
+ *val = reg.status.drdy;
+
+ return mm_error;
+}
+/**
+ * @brief all_sources: [get] Read all the interrupt/status flag of
+ * the device.
+ *
+ * @param lis2dw12_ctx_t *ctx: read / write interface definitions
+ * @param lis2dw12_all_sources: registers STATUS_DUP, WAKE_UP_SRC,
+ * TAP_SRC, SIXD_SRC, ALL_INT_SRC
+ *
+ */
+int32_t lis2dw12_all_sources_get(lis2dw12_ctx_t *ctx,
+ lis2dw12_all_sources_t *val)
+{
+ return lis2dw12_read_reg(ctx, LIS2DW12_STATUS_DUP, (uint8_t*) val, 5);
+}
+/**
+ * @brief usr_offset_x: [set] Accelerometer X-axis user offset correction
+ * expressed in two’s complement, weight
+ * depends on bit USR_OFF_W. The value must be
+ * in the range [-127 127].
+ *
+ * @param lis2dw12_ctx_t *ctx: read / write interface definitions
+ * @param uint8_t * : buffer that contains data to write
+ *
+ */
+int32_t lis2dw12_usr_offset_x_set(lis2dw12_ctx_t *ctx, uint8_t *buff)
+{
+ return lis2dw12_write_reg(ctx, LIS2DW12_X_OFS_USR, buff, 1);
+}
+
+/**
+ * @brief usr_offset_x: [get] Accelerometer X-axis user offset
+ * correction expressed in two’s complement,
+ * weight depends on bit USR_OFF_W.
+ * The value must be in the range [-127 127].
+ *
+ * @param lis2dw12_ctx_t *ctx: read / write interface definitions
+ * @param uint8_t * : buffer that stores data read
+ *
+ */
+int32_t lis2dw12_usr_offset_x_get(lis2dw12_ctx_t *ctx, uint8_t *buff)
+{
+ return lis2dw12_read_reg(ctx, LIS2DW12_X_OFS_USR, buff, 1);
+}
+/**
+ * @brief usr_offset_y: [set] Accelerometer Y-axis user offset
+ * correction expressed in two’s complement,
+ * weight depends on bit USR_OFF_W.
+ * The value must be in the range [-127 127].
+ *
+ * @param lis2dw12_ctx_t *ctx: read / write interface definitions
+ * @param uint8_t * : buffer that contains data to write
+ *
+ */
+int32_t lis2dw12_usr_offset_y_set(lis2dw12_ctx_t *ctx, uint8_t *buff)
+{
+ return lis2dw12_write_reg(ctx, LIS2DW12_Y_OFS_USR, buff, 1);
+}
+
+/**
+ * @brief usr_offset_y: [get] Accelerometer Y-axis user offset
+ * correction expressed in two’s complement,
+ * weight depends on bit USR_OFF_W.
+ * The value must be in the range [-127 127].
+ *
+ * @param lis2dw12_ctx_t *ctx: read / write interface definitions
+ * @param uint8_t * : buffer that stores data read
+ *
+ */
+int32_t lis2dw12_usr_offset_y_get(lis2dw12_ctx_t *ctx, uint8_t *buff)
+{
+ return lis2dw12_read_reg(ctx, LIS2DW12_Y_OFS_USR, buff, 1);
+}
+/**
+ * @brief usr_offset_z: [set] Accelerometer Z-axis user offset
+ * correction expressed in two’s complement,
+ * weight depends on bit USR_OFF_W.
+ * The value must be in the range [-127 127].
+ *
+ * @param lis2dw12_ctx_t *ctx: read / write interface definitions
+ * @param uint8_t * : buffer that contains data to write
+ *
+ */
+int32_t lis2dw12_usr_offset_z_set(lis2dw12_ctx_t *ctx, uint8_t *buff)
+{
+ return lis2dw12_write_reg(ctx, LIS2DW12_Z_OFS_USR, buff, 1);
+}
+
+/**
+ * @brief usr_offset_z: [get] Accelerometer Z-axis user offset
+ * correction expressed in two’s complement,
+ * weight depends on bit USR_OFF_W.
+ * The value must be in the range [-127 127].
+ *
+ * @param lis2dw12_ctx_t *ctx: read / write interface definitions
+ * @param uint8_t * : buffer that stores data read
+ *
+ */
+int32_t lis2dw12_usr_offset_z_get(lis2dw12_ctx_t *ctx, uint8_t *buff)
+{
+ return lis2dw12_read_reg(ctx, LIS2DW12_Z_OFS_USR, buff, 1);
+}
+/**
+ * @brief offset_weight: [set] Weight of XL user offset bits of
+ * registers X_OFS_USR, Y_OFS_USR, Z_OFS_USR.
+ *
+ * @param lis2dw12_ctx_t *ctx: read / write interface definitions
+ * @param lis2dw12_usr_off_w_t: change the values of usr_off_w in
+ * reg CTRL_REG7
+ *
+ */
+int32_t lis2dw12_offset_weight_set(lis2dw12_ctx_t *ctx,
+ lis2dw12_usr_off_w_t val)
+{
+ lis2dw12_reg_t reg;
+ int32_t mm_error;
+
+ mm_error = lis2dw12_read_reg(ctx, LIS2DW12_CTRL_REG7, ®.byte, 1);
+ reg.ctrl_reg7.usr_off_w = val;
+ mm_error = lis2dw12_write_reg(ctx, LIS2DW12_CTRL_REG7, ®.byte, 1);
+
+ return mm_error;
+}
+
+/**
+ * @brief offset_weight: [get] Weight of XL user offset bits of
+ * registers X_OFS_USR, Y_OFS_USR, Z_OFS_USR.
+ *
+ * @param lis2dw12_ctx_t *ctx: read / write interface definitions
+ * @param lis2dw12_usr_off_w_t: Get the values of usr_off_w in reg CTRL_REG7
+ *
+ */
+int32_t lis2dw12_offset_weight_get(lis2dw12_ctx_t *ctx,
+ lis2dw12_usr_off_w_t *val)
+{
+ lis2dw12_reg_t reg;
+ int32_t mm_error;
+
+ mm_error = lis2dw12_read_reg(ctx, LIS2DW12_CTRL_REG7, ®.byte, 1);
+ *val = (lis2dw12_usr_off_w_t) reg.ctrl_reg7.usr_off_w;
+
+ return mm_error;
+}
+
+/**
+ * @}
+ */
+
+/**
+ * @addtogroup Dataoutput
+ * @brief This section groups all the data output functions.
+ * @{
+ */
+
+/**
+ * @brief temperature_raw: [get] Temperature data output register (r).
+ * L and H registers together express a
+ * 16-bit word in two’s complement.
+ *
+ * @param lis2dw12_ctx_t *ctx: read / write interface definitions
+ * @param uint8_t * : buffer that stores data read
+ *
+ */
+int32_t lis2dw12_temperature_raw_get(lis2dw12_ctx_t *ctx, uint8_t *buff)
+{
+ return lis2dw12_read_reg(ctx, LIS2DW12_OUT_T_L, buff, 2);
+}
+
+/**
+ * @brief acceleration_raw: [get] Linear acceleration output register.
+ * The value is expressed as a 16-bit word
+ * in two’s complement.
+ *
+ * @param lis2dw12_ctx_t *ctx: read / write interface definitions
+ * @param uint8_t * : buffer that stores data read
+ *
+ */
+int32_t lis2dw12_acceleration_raw_get(lis2dw12_ctx_t *ctx, uint8_t *buff)
+{
+ return lis2dw12_read_reg(ctx, LIS2DW12_OUT_X_L, buff, 6);
+}
+
+/**
+ * @}
+ */
+
+/**
+ * @addtogroup common
+ * @brief This section groups common usefull functions.
+ * @{
+ */
+
+/**
+ * @brief device_id: [get] DeviceWhoamI.
+ *
+ * @param lis2dw12_ctx_t *ctx: read / write interface definitions
+ * @param uint8_t * : buffer that stores data read
+ *
+ */
+int32_t lis2dw12_device_id_get(lis2dw12_ctx_t *ctx, uint8_t *buff)
+{
+ return lis2dw12_read_reg(ctx, LIS2DW12_WHO_AM_I, buff, 1);
+}
+
+/**
+ * @brief auto_increment: [set] Register address automatically incremented
+ * during multiple byte access with a
+ * serial interface.
+ *
+ * @param lis2dw12_ctx_t *ctx: read / write interface definitions
+ * @param uint8_t val: change the values of if_add_inc in reg CTRL2
+ *
+ */
+int32_t lis2dw12_auto_increment_set(lis2dw12_ctx_t *ctx, uint8_t val)
+{
+ lis2dw12_reg_t reg;
+ int32_t mm_error;
+
+ mm_error = lis2dw12_read_reg(ctx, LIS2DW12_CTRL2, ®.byte, 1);
+ reg.ctrl2.if_add_inc = val;
+ mm_error = lis2dw12_write_reg(ctx, LIS2DW12_CTRL2, ®.byte, 1);
+
+ return mm_error;
+}
+
+/**
+ * @brief auto_increment: [get] Register address automatically
+ * incremented during multiple byte access
+ * with a serial interface.
+ *
+ * @param lis2dw12_ctx_t *ctx: read / write interface definitions
+ * @param uint8_t: change the values of if_add_inc in reg CTRL2
+ *
+ */
+int32_t lis2dw12_auto_increment_get(lis2dw12_ctx_t *ctx, uint8_t *val)
+{
+ lis2dw12_reg_t reg;
+ int32_t mm_error;
+
+ mm_error = lis2dw12_read_reg(ctx, LIS2DW12_CTRL2, ®.byte, 1);
+ *val = reg.ctrl2.if_add_inc;
+
+ return mm_error;
+}
+
+/**
+ * @brief reset: [set] Software reset. Restore the default values in
+ * user registers.
+ *
+ * @param lis2dw12_ctx_t *ctx: read / write interface definitions
+ * @param uint8_t val: change the values of soft_reset in reg CTRL2
+ *
+ */
+int32_t lis2dw12_reset_set(lis2dw12_ctx_t *ctx, uint8_t val)
+{
+ lis2dw12_reg_t reg;
+ int32_t mm_error;
+
+ mm_error = lis2dw12_read_reg(ctx, LIS2DW12_CTRL2, ®.byte, 1);
+ reg.ctrl2.soft_reset = val;
+ mm_error = lis2dw12_write_reg(ctx, LIS2DW12_CTRL2, ®.byte, 1);
+
+ return mm_error;
+}
+
+/**
+ * @brief reset: [get] Software reset. Restore the default values in
+ * user registers.
+ *
+ * @param lis2dw12_ctx_t *ctx: read / write interface definitions
+ * @param uint8_t: change the values of soft_reset in reg CTRL2
+ *
+ */
+int32_t lis2dw12_reset_get(lis2dw12_ctx_t *ctx, uint8_t *val)
+{
+ lis2dw12_reg_t reg;
+ int32_t mm_error;
+
+ mm_error = lis2dw12_read_reg(ctx, LIS2DW12_CTRL2, ®.byte, 1);
+ *val = reg.ctrl2.soft_reset;
+
+ return mm_error;
+}
+
+/**
+ * @brief boot: [set] Reboot memory content. Reload the calibration
+ * parameters.
+ *
+ * @param lis2dw12_ctx_t *ctx: read / write interface definitions
+ * @param uint8_t val: change the values of boot in reg CTRL2
+ *
+ */
+int32_t lis2dw12_boot_set(lis2dw12_ctx_t *ctx, uint8_t val)
+{
+ lis2dw12_reg_t reg;
+ int32_t mm_error;
+
+ mm_error = lis2dw12_read_reg(ctx, LIS2DW12_CTRL2, ®.byte, 1);
+ reg.ctrl2.boot = val;
+ mm_error = lis2dw12_write_reg(ctx, LIS2DW12_CTRL2, ®.byte, 1);
+
+ return mm_error;
+}
+
+/**
+ * @brief boot: [get] Reboot memory content. Reload the calibration
+ * parameters.
+ *
+ * @param lis2dw12_ctx_t *ctx: read / write interface definitions
+ * @param uint8_t: change the values of boot in reg CTRL2
+ *
+ */
+int32_t lis2dw12_boot_get(lis2dw12_ctx_t *ctx, uint8_t *val)
+{
+ lis2dw12_reg_t reg;
+ int32_t mm_error;
+
+ mm_error = lis2dw12_read_reg(ctx, LIS2DW12_CTRL2, ®.byte, 1);
+ *val = reg.ctrl2.boot;
+
+ return mm_error;
+}
+
+/**
+ * @brief self_test: [set] Sensor self-test enable.
+ *
+ * @param lis2dw12_ctx_t *ctx: read / write interface definitions
+ * @param lis2dw12_st_t: change the values of st in reg CTRL3
+ *
+ */
+int32_t lis2dw12_self_test_set(lis2dw12_ctx_t *ctx, lis2dw12_st_t val)
+{
+ lis2dw12_reg_t reg;
+ int32_t mm_error;
+
+ mm_error = lis2dw12_read_reg(ctx, LIS2DW12_CTRL3, ®.byte, 1);
+ reg.ctrl3.st = val;
+ mm_error = lis2dw12_write_reg(ctx, LIS2DW12_CTRL3, ®.byte, 1);
+
+ return mm_error;
+}
+
+/**
+ * @brief self_test: [get] Sensor self-test enable.
+ *
+ * @param lis2dw12_ctx_t *ctx: read / write interface definitions
+ * @param lis2dw12_st_t: Get the values of st in reg CTRL3
+ *
+ */
+int32_t lis2dw12_self_test_get(lis2dw12_ctx_t *ctx, lis2dw12_st_t *val)
+{
+ lis2dw12_reg_t reg;
+ int32_t mm_error;
+
+ mm_error = lis2dw12_read_reg(ctx, LIS2DW12_CTRL3, ®.byte, 1);
+ *val = (lis2dw12_st_t) reg.ctrl3.st;
+
+ return mm_error;
+}
+
+/**
+ * @brief data_ready_mode: [set] Data-ready pulsed / letched mode.
+ *
+ * @param lis2dw12_ctx_t *ctx: read / write interface definitions
+ * @param lis2dw12_drdy_pulsed_t: change the values of drdy_pulsed in
+ * reg CTRL_REG7
+ *
+ */
+int32_t lis2dw12_data_ready_mode_set(lis2dw12_ctx_t *ctx,
+ lis2dw12_drdy_pulsed_t val)
+{
+ lis2dw12_reg_t reg;
+ int32_t mm_error;
+
+ mm_error = lis2dw12_read_reg(ctx, LIS2DW12_CTRL_REG7, ®.byte, 1);
+ reg.ctrl_reg7.drdy_pulsed = val;
+ mm_error = lis2dw12_write_reg(ctx, LIS2DW12_CTRL_REG7, ®.byte, 1);
+
+ return mm_error;
+}
+
+/**
+ * @brief data_ready_mode: [get] Data-ready pulsed / letched mode.
+ *
+ * @param lis2dw12_ctx_t *ctx: read / write interface definitions
+ * @param lis2dw12_drdy_pulsed_t: Get the values of drdy_pulsed in
+ * reg CTRL_REG7
+ *
+ */
+int32_t lis2dw12_data_ready_mode_get(lis2dw12_ctx_t *ctx,
+ lis2dw12_drdy_pulsed_t *val)
+{
+ lis2dw12_reg_t reg;
+ int32_t mm_error;
+
+ mm_error = lis2dw12_read_reg(ctx, LIS2DW12_CTRL_REG7, ®.byte, 1);
+ *val = (lis2dw12_drdy_pulsed_t) reg.ctrl_reg7.drdy_pulsed;
+
+ return mm_error;
+}
+
+/**
+ * @}
+ */
+
+/**
+ * @addtogroup filters
+ * @brief This section group all the functions concerning the filters
+ * configuration.
+ * @{
+ */
+
+/**
+ * @brief filter_path: [set] Accelerometer filtering path for outputs.
+ *
+ * @param lis2dw12_ctx_t *ctx: read / write interface definitions
+ * @param lis2dw12_fds_t: change the values of fds in reg CTRL6
+ *
+ */
+int32_t lis2dw12_filter_path_set(lis2dw12_ctx_t *ctx, lis2dw12_fds_t val)
+{
+ lis2dw12_reg_t reg;
+ int32_t mm_error;
+
+ mm_error = lis2dw12_read_reg(ctx, LIS2DW12_CTRL6, ®.byte, 1);
+ reg.ctrl6.fds = ( val & 0x10 ) >> 4;
+ mm_error = lis2dw12_write_reg(ctx, LIS2DW12_CTRL6, ®.byte, 1);
+
+ mm_error = lis2dw12_read_reg(ctx, LIS2DW12_CTRL_REG7, ®.byte, 1);
+ reg.ctrl_reg7.usr_off_on_out = val & 0x01;
+ mm_error = lis2dw12_write_reg(ctx, LIS2DW12_CTRL_REG7, ®.byte, 1);
+
+ return mm_error;
+}
+
+/**
+ * @brief filter_path: [get] Accelerometer filtering path for outputs.
+ *
+ * @param lis2dw12_ctx_t *ctx: read / write interface definitions
+ * @param lis2dw12_fds_t: Get the values of fds in reg CTRL6
+ *
+ */
+int32_t lis2dw12_filter_path_get(lis2dw12_ctx_t *ctx, lis2dw12_fds_t *val)
+{
+ lis2dw12_reg_t reg[2];
+ int32_t mm_error;
+
+ mm_error = lis2dw12_read_reg(ctx, LIS2DW12_CTRL6, ®[0].byte, 1);
+ mm_error = lis2dw12_read_reg(ctx, LIS2DW12_CTRL_REG7, ®[1].byte, 1);
+
+ *val = (lis2dw12_fds_t) ((reg[0].ctrl6.fds << 4 ) + reg[1].ctrl_reg7.usr_off_on_out);
+
+ return mm_error;
+}
+
+/**
+ * @brief filter_bandwidth: [set] Accelerometer cutoff filter frequency.
+ * Valid for low and high pass filter.
+ *
+ * @param lis2dw12_ctx_t *ctx: read / write interface definitions
+ * @param lis2dw12_bw_filt_t: change the values of bw_filt in reg CTRL6
+ *
+ */
+int32_t lis2dw12_filter_bandwidth_set(lis2dw12_ctx_t *ctx,
+ lis2dw12_bw_filt_t val)
+{
+ lis2dw12_reg_t reg;
+ int32_t mm_error;
+
+ mm_error = lis2dw12_read_reg(ctx, LIS2DW12_CTRL6, ®.byte, 1);
+ reg.ctrl6.bw_filt = val;
+ mm_error = lis2dw12_write_reg(ctx, LIS2DW12_CTRL6, ®.byte, 1);
+
+ return mm_error;
+}
+
+/**
+ * @brief filter_bandwidth: [get] Accelerometer cutoff filter frequency.
+ * Valid for low and high pass filter.
+ *
+ * @param lis2dw12_ctx_t *ctx: read / write interface definitions
+ * @param lis2dw12_bw_filt_t: Get the values of bw_filt in reg CTRL6
+ *
+ */
+int32_t lis2dw12_filter_bandwidth_get(lis2dw12_ctx_t *ctx,
+ lis2dw12_bw_filt_t *val)
+{
+ lis2dw12_reg_t reg;
+ int32_t mm_error;
+
+ mm_error = lis2dw12_read_reg(ctx, LIS2DW12_CTRL6, ®.byte, 1);
+ *val = (lis2dw12_bw_filt_t) reg.ctrl6.bw_filt;
+
+ return mm_error;
+}
+
+/**
+ * @brief reference_mode: [set] Enable HP filter reference mode.
+ *
+ * @param lis2dw12_ctx_t *ctx: read / write interface definitions
+ * @param uint8_t val: change the values of hp_ref_mode in reg CTRL_REG7
+ *
+ */
+int32_t lis2dw12_reference_mode_set(lis2dw12_ctx_t *ctx, uint8_t val)
+{
+ lis2dw12_reg_t reg;
+ int32_t mm_error;
+
+ mm_error = lis2dw12_read_reg(ctx, LIS2DW12_CTRL_REG7, ®.byte, 1);
+ reg.ctrl_reg7.hp_ref_mode = val;
+ mm_error = lis2dw12_write_reg(ctx, LIS2DW12_CTRL_REG7, ®.byte, 1);
+
+ return mm_error;
+}
+
+/**
+ * @brief reference_mode: [get] Enable HP filter reference mode.
+ *
+ * @param lis2dw12_ctx_t *ctx: read / write interface definitions
+ * @param uint8_t: change the values of hp_ref_mode in reg CTRL_REG7
+ *
+ */
+int32_t lis2dw12_reference_mode_get(lis2dw12_ctx_t *ctx, uint8_t *val)
+{
+ lis2dw12_reg_t reg;
+ int32_t mm_error;
+
+ mm_error = lis2dw12_read_reg(ctx, LIS2DW12_CTRL_REG7, ®.byte, 1);
+ *val = reg.ctrl_reg7.hp_ref_mode;
+
+ return mm_error;
+}
+
+/**
+ * @}
+ */
+
+/**
+ * @addtogroup main_serial_interface
+ * @brief This section groups all the functions concerning main serial
+ * interface management (not auxiliary)
+ * @{
+ */
+
+/**
+ * @brief spi_mode: [set] SPI Serial Interface Mode selection.
+ *
+ * @param lis2dw12_ctx_t *ctx: read / write interface definitions
+ * @param lis2dw12_sim_t: change the values of sim in reg CTRL2
+ *
+ */
+int32_t lis2dw12_spi_mode_set(lis2dw12_ctx_t *ctx, lis2dw12_sim_t val)
+{
+ lis2dw12_reg_t reg;
+ int32_t mm_error;
+
+ mm_error = lis2dw12_read_reg(ctx, LIS2DW12_CTRL2, ®.byte, 1);
+ reg.ctrl2.sim = val;
+ mm_error = lis2dw12_write_reg(ctx, LIS2DW12_CTRL2, ®.byte, 1);
+
+ return mm_error;
+}
+
+/**
+ * @brief spi_mode: [get] SPI Serial Interface Mode selection.
+ *
+ * @param lis2dw12_ctx_t *ctx: read / write interface definitions
+ * @param lis2dw12_sim_t: Get the values of sim in reg CTRL2
+ *
+ */
+int32_t lis2dw12_spi_mode_get(lis2dw12_ctx_t *ctx, lis2dw12_sim_t *val)
+{
+ lis2dw12_reg_t reg;
+ int32_t mm_error;
+
+ mm_error = lis2dw12_read_reg(ctx, LIS2DW12_CTRL2, ®.byte, 1);
+ *val = (lis2dw12_sim_t) reg.ctrl2.sim;
+
+ return mm_error;
+}
+
+/**
+ * @brief i2c_interface: [set] Disable / Enable I2C interface.
+ *
+ * @param lis2dw12_ctx_t *ctx: read / write interface definitions
+ * @param lis2dw12_i2c_disable_t: change the values of i2c_disable in
+ * reg CTRL2
+ *
+ */
+int32_t lis2dw12_i2c_interface_set(lis2dw12_ctx_t *ctx,
+ lis2dw12_i2c_disable_t val)
+{
+ lis2dw12_reg_t reg;
+ int32_t mm_error;
+
+ mm_error = lis2dw12_read_reg(ctx, LIS2DW12_CTRL2, ®.byte, 1);
+ reg.ctrl2.i2c_disable = val;
+ mm_error = lis2dw12_write_reg(ctx, LIS2DW12_CTRL2, ®.byte, 1);
+
+ return mm_error;
+}
+
+/**
+ * @brief i2c_interface: [get] Disable / Enable I2C interface.
+ *
+ * @param lis2dw12_ctx_t *ctx: read / write interface definitions
+ * @param lis2dw12_i2c_disable_t: Get the values of i2c_disable in reg CTRL2
+ *
+ */
+int32_t lis2dw12_i2c_interface_get(lis2dw12_ctx_t *ctx,
+ lis2dw12_i2c_disable_t *val)
+{
+ lis2dw12_reg_t reg;
+ int32_t mm_error;
+
+ mm_error = lis2dw12_read_reg(ctx, LIS2DW12_CTRL2, ®.byte, 1);
+ *val = (lis2dw12_i2c_disable_t) reg.ctrl2.i2c_disable;
+
+ return mm_error;
+}
+
+/**
+ * @brief cs_mode: [set] Disconnect CS pull-up.
+ *
+ * @param lis2dw12_ctx_t *ctx: read / write interface definitions
+ * @param lis2dw12_cs_pu_disc_t: change the values of cs_pu_disc in reg CTRL2
+ *
+ */
+int32_t lis2dw12_cs_mode_set(lis2dw12_ctx_t *ctx, lis2dw12_cs_pu_disc_t val)
+{
+ lis2dw12_reg_t reg;
+ int32_t mm_error;
+
+ mm_error = lis2dw12_read_reg(ctx, LIS2DW12_CTRL2, ®.byte, 1);
+ reg.ctrl2.cs_pu_disc = val;
+ mm_error = lis2dw12_write_reg(ctx, LIS2DW12_CTRL2, ®.byte, 1);
+
+ return mm_error;
+}
+
+/**
+ * @brief cs_mode: [get] Disconnect CS pull-up.
+ *
+ * @param lis2dw12_ctx_t *ctx: read / write interface definitions
+ * @param lis2dw12_cs_pu_disc_t: Get the values of cs_pu_disc in reg CTRL2
+ *
+ */
+int32_t lis2dw12_cs_mode_get(lis2dw12_ctx_t *ctx, lis2dw12_cs_pu_disc_t *val)
+{
+ lis2dw12_reg_t reg;
+ int32_t mm_error;
+
+ mm_error = lis2dw12_read_reg(ctx, LIS2DW12_CTRL2, ®.byte, 1);
+ *val = (lis2dw12_cs_pu_disc_t) reg.ctrl2.cs_pu_disc;
+
+ return mm_error;
+}
+
+/**
+ * @}
+ */
+
+/**
+ * @addtogroup interrupt_pins
+ * @brief This section groups all the functions that manage interrup pins
+ * @{
+ */
+
+/**
+ * @brief pin_polarity: [set] Interrupt active-high/low.
+ *
+ * @param lis2dw12_ctx_t *ctx: read / write interface definitions
+ * @param lis2dw12_h_lactive_t: change the values of h_lactive in reg CTRL3
+ *
+ */
+int32_t lis2dw12_pin_polarity_set(lis2dw12_ctx_t *ctx,
+ lis2dw12_h_lactive_t val)
+{
+ lis2dw12_reg_t reg;
+ int32_t mm_error;
+
+ mm_error = lis2dw12_read_reg(ctx, LIS2DW12_CTRL3, ®.byte, 1);
+ reg.ctrl3.h_lactive = val;
+ mm_error = lis2dw12_write_reg(ctx, LIS2DW12_CTRL3, ®.byte, 1);
+
+ return mm_error;
+}
+
+/**
+ * @brief pin_polarity: [get] Interrupt active-high/low.
+ *
+ * @param lis2dw12_ctx_t *ctx: read / write interface definitions
+ * @param lis2dw12_h_lactive_t: Get the values of h_lactive in reg CTRL3
+ *
+ */
+int32_t lis2dw12_pin_polarity_get(lis2dw12_ctx_t *ctx,
+ lis2dw12_h_lactive_t *val)
+{
+ lis2dw12_reg_t reg;
+ int32_t mm_error;
+
+ mm_error = lis2dw12_read_reg(ctx, LIS2DW12_CTRL3, ®.byte, 1);
+ *val = (lis2dw12_h_lactive_t) reg.ctrl3.h_lactive;
+
+ return mm_error;
+}
+
+/**
+ * @brief int_notification: [set] Latched/pulsed interrupt.
+ *
+ * @param lis2dw12_ctx_t *ctx: read / write interface definitions
+ * @param lis2dw12_lir_t: change the values of lir in reg CTRL3
+ *
+ */
+int32_t lis2dw12_int_notification_set(lis2dw12_ctx_t *ctx,
+ lis2dw12_lir_t val)
+{
+ lis2dw12_reg_t reg;
+ int32_t mm_error;
+
+ mm_error = lis2dw12_read_reg(ctx, LIS2DW12_CTRL3, ®.byte, 1);
+ reg.ctrl3.lir = val;
+ mm_error = lis2dw12_write_reg(ctx, LIS2DW12_CTRL3, ®.byte, 1);
+
+ return mm_error;
+}
+
+/**
+ * @brief int_notification: [get] Latched/pulsed interrupt.
+ *
+ * @param lis2dw12_ctx_t *ctx: read / write interface definitions
+ * @param lis2dw12_lir_t: Get the values of lir in reg CTRL3
+ *
+ */
+int32_t lis2dw12_int_notification_get(lis2dw12_ctx_t *ctx,
+ lis2dw12_lir_t *val)
+{
+ lis2dw12_reg_t reg;
+ int32_t mm_error;
+
+ mm_error = lis2dw12_read_reg(ctx, LIS2DW12_CTRL3, ®.byte, 1);
+ *val = (lis2dw12_lir_t) reg.ctrl3.lir;
+
+ return mm_error;
+}
+
+/**
+ * @brief pin_mode: [set] Push-pull/open drain selection on interrupt pads.
+ *
+ * @param lis2dw12_ctx_t *ctx: read / write interface definitions
+ * @param lis2dw12_pp_od_t: change the values of pp_od in reg CTRL3
+ *
+ */
+int32_t lis2dw12_pin_mode_set(lis2dw12_ctx_t *ctx, lis2dw12_pp_od_t val)
+{
+ lis2dw12_reg_t reg;
+ int32_t mm_error;
+
+ mm_error = lis2dw12_read_reg(ctx, LIS2DW12_CTRL3, ®.byte, 1);
+ reg.ctrl3.pp_od = val;
+ mm_error = lis2dw12_write_reg(ctx, LIS2DW12_CTRL3, ®.byte, 1);
+
+ return mm_error;
+}
+
+/**
+ * @brief pin_mode: [get] Push-pull/open drain selection on interrupt pads.
+ *
+ * @param lis2dw12_ctx_t *ctx: read / write interface definitions
+ * @param lis2dw12_pp_od_t: Get the values of pp_od in reg CTRL3
+ *
+ */
+int32_t lis2dw12_pin_mode_get(lis2dw12_ctx_t *ctx, lis2dw12_pp_od_t *val)
+{
+ lis2dw12_reg_t reg;
+ int32_t mm_error;
+
+ mm_error = lis2dw12_read_reg(ctx, LIS2DW12_CTRL3, ®.byte, 1);
+ *val = (lis2dw12_pp_od_t) reg.ctrl3.pp_od;
+
+ return mm_error;
+}
+
+/**
+ * @brief pin_int1_route: [set] Select the signal that need to
+ * route on int1 pad.
+ *
+ * @param lis2dw12_ctx_t *ctx: read / write interface definitions
+ * @param lis2dw12_: register CTRL4_INT1_PAD_CTRL.
+ *
+ */
+int32_t lis2dw12_pin_int1_route_set(lis2dw12_ctx_t *ctx,
+ lis2dw12_ctrl4_int1_pad_ctrl_t *val)
+{
+ lis2dw12_reg_t reg;
+ int32_t mm_error;
+
+ mm_error = lis2dw12_read_reg(ctx, LIS2DW12_CTRL_REG7, ®.byte, 1);
+
+ if (val->int1_tap || val->int1_ff || val->int1_wu || val->int1_single_tap ||
+ val->int1_6d){
+ reg.ctrl_reg7.interrupts_enable = PROPERTY_ENABLE;
+ }
+ else{
+ reg.ctrl_reg7.interrupts_enable = PROPERTY_DISABLE;
+ }
+
+ mm_error = lis2dw12_write_reg(ctx, LIS2DW12_CTRL4_INT1_PAD_CTRL,
+ (uint8_t*) val, 1);
+
+ mm_error = lis2dw12_write_reg(ctx, LIS2DW12_CTRL_REG7, ®.byte, 1);
+
+ return mm_error;
+}
+
+/**
+ * @brief pin_int1_route: [get] Select the signal that need to route on
+ * int1 pad.
+ *
+ * @param lis2dw12_ctx_t *ctx: read / write interface definitions
+ * @param lis2dw12_: register CTRL4_INT1_PAD_CTRL.
+ *
+ */
+int32_t lis2dw12_pin_int1_route_get(lis2dw12_ctx_t *ctx,
+ lis2dw12_ctrl4_int1_pad_ctrl_t *val)
+{
+ return lis2dw12_read_reg(ctx, LIS2DW12_CTRL4_INT1_PAD_CTRL,
+ (uint8_t*) val, 1);
+}
+/**
+ * @brief pin_int2_route: [set] Select the signal that need to route on
+ * int2 pad.
+ *
+ * @param lis2dw12_ctx_t *ctx: read / write interface definitions
+ * @param lis2dw12_: register CTRL5_INT2_PAD_CTRL.
+ *
+ */
+int32_t lis2dw12_pin_int2_route_set(lis2dw12_ctx_t *ctx,
+ lis2dw12_ctrl5_int2_pad_ctrl_t *val)
+{
+ lis2dw12_reg_t reg;
+ int32_t mm_error;
+
+ mm_error = lis2dw12_read_reg(ctx, LIS2DW12_CTRL_REG7, ®.byte, 1);
+
+ if ( val->int2_sleep_state || val->int2_sleep_chg ){
+ reg.ctrl_reg7.interrupts_enable = PROPERTY_ENABLE;
+ }
+ else{
+ reg.ctrl_reg7.interrupts_enable = PROPERTY_DISABLE;
+ }
+
+ mm_error = lis2dw12_write_reg(ctx, LIS2DW12_CTRL5_INT2_PAD_CTRL,
+ (uint8_t*) val, 1);
+
+ mm_error = lis2dw12_write_reg(ctx, LIS2DW12_CTRL_REG7, ®.byte, 1);
+
+ return mm_error;
+}
+
+/**
+ * @brief pin_int2_route: [get] Select the signal that need to route on
+ * int2 pad.
+ *
+ * @param lis2dw12_ctx_t *ctx: read / write interface definitions
+ * @param lis2dw12_: register CTRL5_INT2_PAD_CTRL
+ *
+ */
+int32_t lis2dw12_pin_int2_route_get(lis2dw12_ctx_t *ctx,
+ lis2dw12_ctrl5_int2_pad_ctrl_t *val)
+{
+ return lis2dw12_read_reg(ctx, LIS2DW12_CTRL5_INT2_PAD_CTRL,
+ (uint8_t*) val, 1);
+}
+/**
+ * @brief all_on_int1: [set] All interrupt signals become available
+ * on INT1 pin.
+ *
+ * @param lis2dw12_ctx_t *ctx: read / write interface definitions
+ * @param uint8_t val: change the values of int2_on_int1 in reg CTRL_REG7
+ *
+ */
+int32_t lis2dw12_all_on_int1_set(lis2dw12_ctx_t *ctx, uint8_t val)
+{
+ lis2dw12_reg_t reg;
+ int32_t mm_error;
+
+ mm_error = lis2dw12_read_reg(ctx, LIS2DW12_CTRL_REG7, ®.byte, 1);
+ reg.ctrl_reg7.int2_on_int1 = val;
+ mm_error = lis2dw12_write_reg(ctx, LIS2DW12_CTRL_REG7, ®.byte, 1);
+
+ return mm_error;
+}
+
+/**
+ * @brief all_on_int1: [get] All interrupt signals become available
+ * on INT1 pin.
+ *
+ * @param lis2dw12_ctx_t *ctx: read / write interface definitions
+ * @param uint8_t: change the values of int2_on_int1 in reg CTRL_REG7
+ *
+ */
+int32_t lis2dw12_all_on_int1_get(lis2dw12_ctx_t *ctx, uint8_t *val)
+{
+ lis2dw12_reg_t reg;
+ int32_t mm_error;
+
+ mm_error = lis2dw12_read_reg(ctx, LIS2DW12_CTRL_REG7, ®.byte, 1);
+ *val = reg.ctrl_reg7.int2_on_int1;
+
+ return mm_error;
+}
+
+/**
+ * @}
+ */
+
+/**
+ * @addtogroup Wake_Up_event
+ * @brief This section groups all the functions that manage the Wake
+ * Up event generation.
+ * @{
+ */
+
+/**
+ * @brief wkup_threshold: [set] Threshold for wakeup.1 LSB = FS_XL / 64.
+ *
+ * @param lis2dw12_ctx_t *ctx: read / write interface definitions
+ * @param uint8_t val: change the values of wk_ths in reg WAKE_UP_THS
+ *
+ */
+int32_t lis2dw12_wkup_threshold_set(lis2dw12_ctx_t *ctx, uint8_t val)
+{
+ lis2dw12_reg_t reg;
+ int32_t mm_error;
+
+ mm_error = lis2dw12_read_reg(ctx, LIS2DW12_WAKE_UP_THS, ®.byte, 1);
+ reg.wake_up_ths.wk_ths = val;
+ mm_error = lis2dw12_write_reg(ctx, LIS2DW12_WAKE_UP_THS, ®.byte, 1);
+
+ return mm_error;
+}
+
+/**
+ * @brief wkup_threshold: [get] Threshold for wakeup.1 LSB = FS_XL / 64.
+ *
+ * @param lis2dw12_ctx_t *ctx: read / write interface definitions
+ * @param uint8_t: change the values of wk_ths in reg WAKE_UP_THS
+ *
+ */
+int32_t lis2dw12_wkup_threshold_get(lis2dw12_ctx_t *ctx, uint8_t *val)
+{
+ lis2dw12_reg_t reg;
+ int32_t mm_error;
+
+ mm_error = lis2dw12_read_reg(ctx, LIS2DW12_WAKE_UP_THS, ®.byte, 1);
+ *val = reg.wake_up_ths.wk_ths;
+
+ return mm_error;
+}
+
+/**
+ * @brief wkup_dur: [set] Wake up duration event.1LSb = 1 / ODR.
+ *
+ * @param lis2dw12_ctx_t *ctx: read / write interface definitions
+ * @param uint8_t val: change the values of wake_dur in reg WAKE_UP_DUR
+ *
+ */
+int32_t lis2dw12_wkup_dur_set(lis2dw12_ctx_t *ctx, uint8_t val)
+{
+ lis2dw12_reg_t reg;
+ int32_t mm_error;
+
+ mm_error = lis2dw12_read_reg(ctx, LIS2DW12_WAKE_UP_DUR, ®.byte, 1);
+ reg.wake_up_dur.wake_dur = val;
+ mm_error = lis2dw12_write_reg(ctx, LIS2DW12_WAKE_UP_DUR, ®.byte, 1);
+
+ return mm_error;
+}
+
+/**
+ * @brief wkup_dur: [get] Wake up duration event.1LSb = 1 / ODR.
+ *
+ * @param lis2dw12_ctx_t *ctx: read / write interface definitions
+ * @param uint8_t: change the values of wake_dur in reg WAKE_UP_DUR
+ *
+ */
+int32_t lis2dw12_wkup_dur_get(lis2dw12_ctx_t *ctx, uint8_t *val)
+{
+ lis2dw12_reg_t reg;
+ int32_t mm_error;
+
+ mm_error = lis2dw12_read_reg(ctx, LIS2DW12_WAKE_UP_DUR, ®.byte, 1);
+ *val = reg.wake_up_dur.wake_dur;
+
+ return mm_error;
+}
+
+/**
+ * @brief wkup_feed_data: [set] Data sent to wake-up interrupt function.
+ *
+ * @param lis2dw12_ctx_t *ctx: read / write interface definitions
+ * @param lis2dw12_usr_off_on_wu_t: change the values of usr_off_on_wu in
+ * reg CTRL_REG7
+ *
+ */
+int32_t lis2dw12_wkup_feed_data_set(lis2dw12_ctx_t *ctx,
+ lis2dw12_usr_off_on_wu_t val)
+{
+ lis2dw12_reg_t reg;
+ int32_t mm_error;
+
+ mm_error = lis2dw12_read_reg(ctx, LIS2DW12_CTRL_REG7, ®.byte, 1);
+ reg.ctrl_reg7.usr_off_on_wu = val;
+ mm_error = lis2dw12_write_reg(ctx, LIS2DW12_CTRL_REG7, ®.byte, 1);
+
+ return mm_error;
+}
+
+/**
+ * @brief wkup_feed_data: [get] Data sent to wake-up interrupt function.
+ *
+ * @param lis2dw12_ctx_t *ctx: read / write interface definitions
+ * @param lis2dw12_usr_off_on_wu_t: Get the values of usr_off_on_wu in
+ * reg CTRL_REG7
+ *
+ */
+int32_t lis2dw12_wkup_feed_data_get(lis2dw12_ctx_t *ctx,
+ lis2dw12_usr_off_on_wu_t *val)
+{
+ lis2dw12_reg_t reg;
+ int32_t mm_error;
+
+ mm_error = lis2dw12_read_reg(ctx, LIS2DW12_CTRL_REG7, ®.byte, 1);
+ *val = (lis2dw12_usr_off_on_wu_t) reg.ctrl_reg7.usr_off_on_wu;
+
+ return mm_error;
+}
+
+/**
+ * @}
+ */
+
+/**
+ * @addtogroup Activity/Inactivity_detection
+ * @brief This section groups all the functions concerning
+ * activity/inactivity detection.
+ * @{
+ */
+
+/**
+ * @brief act_mode: [set] Config activity / inactivity or
+ * stationary / motion detection.
+ *
+ * @param lis2dw12_ctx_t *ctx: read / write interface definitions
+ * @param lis2dw12_sleep_on_t: change the values of sleep_on / stationary in
+ * reg WAKE_UP_THS / WAKE_UP_DUR
+ *
+ */
+int32_t lis2dw12_act_mode_set(lis2dw12_ctx_t *ctx, lis2dw12_sleep_on_t val)
+{
+ lis2dw12_reg_t reg[2];
+ int32_t mm_error;
+
+ mm_error = lis2dw12_read_reg(ctx, LIS2DW12_WAKE_UP_THS, ®[0].byte, 2);
+ reg[0].wake_up_ths.sleep_on = val & 0x01;
+ reg[1].wake_up_dur.stationary = (val & 0x02) >> 1;
+ mm_error = lis2dw12_write_reg(ctx, LIS2DW12_WAKE_UP_THS, ®[0].byte, 2);
+
+ return mm_error;
+}
+
+/**
+ * @brief act_mode: [get] Config activity / inactivity or
+ * stationary / motion detection.
+ *
+ * @param lis2dw12_ctx_t *ctx: read / write interface definitions
+ * @param lis2dw12_sleep_on_t: Get the values of sleep_on in reg WAKE_UP_THS
+ *
+ */
+int32_t lis2dw12_act_mode_get(lis2dw12_ctx_t *ctx, lis2dw12_sleep_on_t *val)
+{
+ lis2dw12_reg_t reg[2];
+ int32_t mm_error;
+
+ mm_error = lis2dw12_read_reg(ctx, LIS2DW12_WAKE_UP_THS, ®[0].byte, 2);
+ *val = (lis2dw12_sleep_on_t) ((reg[1].wake_up_dur.stationary << 1)
+ + reg[0].wake_up_ths.sleep_on);
+
+ return mm_error;
+}
+
+/**
+ * @brief act_sleep_dur: [set] Duration to go in sleep mode.
+ * 1 LSb = 512 / ODR.
+ *
+ * @param lis2dw12_ctx_t *ctx: read / write interface definitions
+ * @param uint8_t val: change the values of sleep_dur in reg WAKE_UP_DUR
+ *
+ */
+int32_t lis2dw12_act_sleep_dur_set(lis2dw12_ctx_t *ctx, uint8_t val)
+{
+ lis2dw12_reg_t reg;
+ int32_t mm_error;
+
+ mm_error = lis2dw12_read_reg(ctx, LIS2DW12_WAKE_UP_DUR, ®.byte, 1);
+ reg.wake_up_dur.sleep_dur = val;
+ mm_error = lis2dw12_write_reg(ctx, LIS2DW12_WAKE_UP_DUR, ®.byte, 1);
+
+ return mm_error;
+}
+
+/**
+ * @brief act_sleep_dur: [get] Duration to go in sleep mode.
+ * 1 LSb = 512 / ODR.
+ *
+ * @param lis2dw12_ctx_t *ctx: read / write interface definitions
+ * @param uint8_t: change the values of sleep_dur in reg WAKE_UP_DUR
+ *
+ */
+int32_t lis2dw12_act_sleep_dur_get(lis2dw12_ctx_t *ctx, uint8_t *val)
+{
+ lis2dw12_reg_t reg;
+ int32_t mm_error;
+
+ mm_error = lis2dw12_read_reg(ctx, LIS2DW12_WAKE_UP_DUR, ®.byte, 1);
+ *val = reg.wake_up_dur.sleep_dur;
+
+ return mm_error;
+}
+
+/**
+ * @}
+ */
+
+/**
+ * @addtogroup tap_generator
+ * @brief This section groups all the functions that manage the tap
+ * and double tap event generation.
+ * @{
+ */
+
+/**
+ * @brief tap_threshold_x: [set] Threshold for tap recognition.
+ *
+ * @param lis2dw12_ctx_t *ctx: read / write interface definitions
+ * @param uint8_t val: change the values of tap_thsx in reg TAP_THS_X
+ *
+ */
+int32_t lis2dw12_tap_threshold_x_set(lis2dw12_ctx_t *ctx, uint8_t val)
+{
+ lis2dw12_reg_t reg;
+ int32_t mm_error;
+
+ mm_error = lis2dw12_read_reg(ctx, LIS2DW12_TAP_THS_X, ®.byte, 1);
+ reg.tap_ths_x.tap_thsx = val;
+ mm_error = lis2dw12_write_reg(ctx, LIS2DW12_TAP_THS_X, ®.byte, 1);
+
+ return mm_error;
+}
+
+/**
+ * @brief tap_threshold_x: [get] Threshold for tap recognition.
+ *
+ * @param lis2dw12_ctx_t *ctx: read / write interface definitions
+ * @param uint8_t: change the values of tap_thsx in reg TAP_THS_X
+ *
+ */
+int32_t lis2dw12_tap_threshold_x_get(lis2dw12_ctx_t *ctx, uint8_t *val)
+{
+ lis2dw12_reg_t reg;
+ int32_t mm_error;
+
+ mm_error = lis2dw12_read_reg(ctx, LIS2DW12_TAP_THS_X, ®.byte, 1);
+ *val = reg.tap_ths_x.tap_thsx;
+
+ return mm_error;
+}
+
+/**
+ * @brief tap_threshold_y: [set] Threshold for tap recognition.
+ *
+ * @param lis2dw12_ctx_t *ctx: read / write interface definitions
+ * @param uint8_t val: change the values of tap_thsy in reg TAP_THS_Y
+ *
+ */
+int32_t lis2dw12_tap_threshold_y_set(lis2dw12_ctx_t *ctx, uint8_t val)
+{
+ lis2dw12_reg_t reg;
+ int32_t mm_error;
+
+ mm_error = lis2dw12_read_reg(ctx, LIS2DW12_TAP_THS_Y, ®.byte, 1);
+ reg.tap_ths_y.tap_thsy = val;
+ mm_error = lis2dw12_write_reg(ctx, LIS2DW12_TAP_THS_Y, ®.byte, 1);
+
+ return mm_error;
+}
+
+/**
+ * @brief tap_threshold_y: [get] Threshold for tap recognition.
+ *
+ * @param lis2dw12_ctx_t *ctx: read / write interface definitions
+ * @param uint8_t: change the values of tap_thsy in reg TAP_THS_Y
+ *
+ */
+int32_t lis2dw12_tap_threshold_y_get(lis2dw12_ctx_t *ctx, uint8_t *val)
+{
+ lis2dw12_reg_t reg;
+ int32_t mm_error;
+
+ mm_error = lis2dw12_read_reg(ctx, LIS2DW12_TAP_THS_Y, ®.byte, 1);
+ *val = reg.tap_ths_y.tap_thsy;
+
+ return mm_error;
+}
+
+/**
+ * @brief tap_axis_priority: [set] Selection of axis priority for
+ * TAP detection.
+ *
+ * @param lis2dw12_ctx_t *ctx: read / write interface definitions
+ * @param lis2dw12_tap_prior_t: change the values of tap_prior in
+ * reg TAP_THS_Y
+ *
+ */
+int32_t lis2dw12_tap_axis_priority_set(lis2dw12_ctx_t *ctx,
+ lis2dw12_tap_prior_t val)
+{
+ lis2dw12_reg_t reg;
+ int32_t mm_error;
+
+ mm_error = lis2dw12_read_reg(ctx, LIS2DW12_TAP_THS_Y, ®.byte, 1);
+ reg.tap_ths_y.tap_prior = val;
+ mm_error = lis2dw12_write_reg(ctx, LIS2DW12_TAP_THS_Y, ®.byte, 1);
+
+ return mm_error;
+}
+
+/**
+ * @brief tap_axis_priority: [get] Selection of axis priority for
+ * TAP detection.
+ *
+ * @param lis2dw12_ctx_t *ctx: read / write interface definitions
+ * @param lis2dw12_tap_prior_t: Get the values of tap_prior in reg TAP_THS_Y
+ *
+ */
+int32_t lis2dw12_tap_axis_priority_get(lis2dw12_ctx_t *ctx,
+ lis2dw12_tap_prior_t *val)
+{
+ lis2dw12_reg_t reg;
+ int32_t mm_error;
+
+ mm_error = lis2dw12_read_reg(ctx, LIS2DW12_TAP_THS_Y, ®.byte, 1);
+ *val = (lis2dw12_tap_prior_t) reg.tap_ths_y.tap_prior;
+
+ return mm_error;
+}
+
+/**
+ * @brief tap_threshold_z: [set] Threshold for tap recognition.
+ *
+ * @param lis2dw12_ctx_t *ctx: read / write interface definitions
+ * @param uint8_t val: change the values of tap_thsz in reg TAP_THS_Z
+ *
+ */
+int32_t lis2dw12_tap_threshold_z_set(lis2dw12_ctx_t *ctx, uint8_t val)
+{
+ lis2dw12_reg_t reg;
+ int32_t mm_error;
+
+ mm_error = lis2dw12_read_reg(ctx, LIS2DW12_TAP_THS_Z, ®.byte, 1);
+ reg.tap_ths_z.tap_thsz = val;
+ mm_error = lis2dw12_write_reg(ctx, LIS2DW12_TAP_THS_Z, ®.byte, 1);
+
+ return mm_error;
+}
+
+/**
+ * @brief tap_threshold_z: [get] Threshold for tap recognition.
+ *
+ * @param lis2dw12_ctx_t *ctx: read / write interface definitions
+ * @param uint8_t: change the values of tap_thsz in reg TAP_THS_Z
+ *
+ */
+int32_t lis2dw12_tap_threshold_z_get(lis2dw12_ctx_t *ctx, uint8_t *val)
+{
+ lis2dw12_reg_t reg;
+ int32_t mm_error;
+
+ mm_error = lis2dw12_read_reg(ctx, LIS2DW12_TAP_THS_Z, ®.byte, 1);
+ *val = reg.tap_ths_z.tap_thsz;
+
+ return mm_error;
+}
+
+/**
+ * @brief tap_detection_on_z: [set] Enable Z direction in tap recognition.
+ *
+ * @param lis2dw12_ctx_t *ctx: read / write interface definitions
+ * @param uint8_t val: change the values of tap_z_en in reg TAP_THS_Z
+ *
+ */
+int32_t lis2dw12_tap_detection_on_z_set(lis2dw12_ctx_t *ctx, uint8_t val)
+{
+ lis2dw12_reg_t reg;
+ int32_t mm_error;
+
+ mm_error = lis2dw12_read_reg(ctx, LIS2DW12_TAP_THS_Z, ®.byte, 1);
+ reg.tap_ths_z.tap_z_en = val;
+ mm_error = lis2dw12_write_reg(ctx, LIS2DW12_TAP_THS_Z, ®.byte, 1);
+
+ return mm_error;
+}
+
+/**
+ * @brief tap_detection_on_z: [get] Enable Z direction in tap recognition.
+ *
+ * @param lis2dw12_ctx_t *ctx: read / write interface definitions
+ * @param uint8_t: change the values of tap_z_en in reg TAP_THS_Z
+ *
+ */
+int32_t lis2dw12_tap_detection_on_z_get(lis2dw12_ctx_t *ctx, uint8_t *val)
+{
+ lis2dw12_reg_t reg;
+ int32_t mm_error;
+
+ mm_error = lis2dw12_read_reg(ctx, LIS2DW12_TAP_THS_Z, ®.byte, 1);
+ *val = reg.tap_ths_z.tap_z_en;
+
+ return mm_error;
+}
+
+/**
+ * @brief tap_detection_on_y: [set] Enable Y direction in tap recognition.
+ *
+ * @param lis2dw12_ctx_t *ctx: read / write interface definitions
+ * @param uint8_t val: change the values of tap_y_en in reg TAP_THS_Z
+ *
+ */
+int32_t lis2dw12_tap_detection_on_y_set(lis2dw12_ctx_t *ctx, uint8_t val)
+{
+ lis2dw12_reg_t reg;
+ int32_t mm_error;
+
+ mm_error = lis2dw12_read_reg(ctx, LIS2DW12_TAP_THS_Z, ®.byte, 1);
+ reg.tap_ths_z.tap_y_en = val;
+ mm_error = lis2dw12_write_reg(ctx, LIS2DW12_TAP_THS_Z, ®.byte, 1);
+
+ return mm_error;
+}
+
+/**
+ * @brief tap_detection_on_y: [get] Enable Y direction in tap recognition.
+ *
+ * @param lis2dw12_ctx_t *ctx: read / write interface definitions
+ * @param uint8_t: change the values of tap_y_en in reg TAP_THS_Z
+ *
+ */
+int32_t lis2dw12_tap_detection_on_y_get(lis2dw12_ctx_t *ctx, uint8_t *val)
+{
+ lis2dw12_reg_t reg;
+ int32_t mm_error;
+
+ mm_error = lis2dw12_read_reg(ctx, LIS2DW12_TAP_THS_Z, ®.byte, 1);
+ *val = reg.tap_ths_z.tap_y_en;
+
+ return mm_error;
+}
+
+/**
+ * @brief tap_detection_on_x: [set] Enable X direction in tap recognition.
+ *
+ * @param lis2dw12_ctx_t *ctx: read / write interface definitions
+ * @param uint8_t val: change the values of tap_x_en in reg TAP_THS_Z
+ *
+ */
+int32_t lis2dw12_tap_detection_on_x_set(lis2dw12_ctx_t *ctx, uint8_t val)
+{
+ lis2dw12_reg_t reg;
+ int32_t mm_error;
+
+ mm_error = lis2dw12_read_reg(ctx, LIS2DW12_TAP_THS_Z, ®.byte, 1);
+ reg.tap_ths_z.tap_x_en = val;
+ mm_error = lis2dw12_write_reg(ctx, LIS2DW12_TAP_THS_Z, ®.byte, 1);
+
+ return mm_error;
+}
+
+/**
+ * @brief tap_detection_on_x: [get] Enable X direction in tap recognition.
+ *
+ * @param lis2dw12_ctx_t *ctx: read / write interface definitions
+ * @param uint8_t: change the values of tap_x_en in reg TAP_THS_Z
+ *
+ */
+int32_t lis2dw12_tap_detection_on_x_get(lis2dw12_ctx_t *ctx, uint8_t *val)
+{
+ lis2dw12_reg_t reg;
+ int32_t mm_error;
+
+ mm_error = lis2dw12_read_reg(ctx, LIS2DW12_TAP_THS_Z, ®.byte, 1);
+ *val = reg.tap_ths_z.tap_x_en;
+
+ return mm_error;
+}
+
+/**
+ * @brief tap_shock: [set] Maximum duration is the maximum time of an
+ * overthreshold signal detection to be recognized
+ * as a tap event. The default value of these bits
+ * is 00b which corresponds to 4*ODR_XL time.
+ * If the SHOCK[1:0] bits are set to a different
+ * value, 1LSB corresponds to 8*ODR_XL time.
+ *
+ * @param lis2dw12_ctx_t *ctx: read / write interface definitions
+ * @param uint8_t val: change the values of shock in reg INT_DUR
+ *
+ */
+int32_t lis2dw12_tap_shock_set(lis2dw12_ctx_t *ctx, uint8_t val)
+{
+ lis2dw12_reg_t reg;
+ int32_t mm_error;
+
+ mm_error = lis2dw12_read_reg(ctx, LIS2DW12_INT_DUR, ®.byte, 1);
+ reg.int_dur.shock = val;
+ mm_error = lis2dw12_write_reg(ctx, LIS2DW12_INT_DUR, ®.byte, 1);
+
+ return mm_error;
+}
+
+/**
+ * @brief tap_shock: [get] Maximum duration is the maximum time of an
+ * overthreshold signal detection to be
+ * recognized as a tap event.
+ * The default value of these bits is 00b which
+ * corresponds to 4*ODR_XL time.
+ * If the SHOCK[1:0] bits are set to a different
+ * value, 1LSB corresponds to 8*ODR_XL time.
+ *
+ * @param lis2dw12_ctx_t *ctx: read / write interface definitions
+ * @param uint8_t: change the values of shock in reg INT_DUR
+ *
+ */
+int32_t lis2dw12_tap_shock_get(lis2dw12_ctx_t *ctx, uint8_t *val)
+{
+ lis2dw12_reg_t reg;
+ int32_t mm_error;
+
+ mm_error = lis2dw12_read_reg(ctx, LIS2DW12_INT_DUR, ®.byte, 1);
+ *val = reg.int_dur.shock;
+
+ return mm_error;
+}
+
+/**
+ * @brief tap_quiet: [set] Quiet time is the time after the first
+ * detected tap in which there must not be any
+ * overthreshold event.
+ * The default value of these bits is 00b which
+ * corresponds to 2*ODR_XL time.
+ * If the QUIET[1:0] bits are set to a different
+ * value, 1LSB corresponds to 4*ODR_XL time.
+ *
+ * @param lis2dw12_ctx_t *ctx: read / write interface definitions
+ * @param uint8_t val: change the values of quiet in reg INT_DUR
+ *
+ */
+int32_t lis2dw12_tap_quiet_set(lis2dw12_ctx_t *ctx, uint8_t val)
+{
+ lis2dw12_reg_t reg;
+ int32_t mm_error;
+
+ mm_error = lis2dw12_read_reg(ctx, LIS2DW12_INT_DUR, ®.byte, 1);
+ reg.int_dur.quiet = val;
+ mm_error = lis2dw12_write_reg(ctx, LIS2DW12_INT_DUR, ®.byte, 1);
+
+ return mm_error;
+}
+
+/**
+ * @brief tap_quiet: [get] Quiet time is the time after the first
+ * detected tap in which there must not be
+ * any overthreshold event.
+ * The default value of these bits is 00b which
+ * corresponds to 2*ODR_XL time.
+ * If the QUIET[1:0] bits are set to a different
+ * value, 1LSB corresponds to 4*ODR_XL time.
+ *
+ * @param lis2dw12_ctx_t *ctx: read / write interface definitions
+ * @param uint8_t: change the values of quiet in reg INT_DUR
+ *
+ */
+int32_t lis2dw12_tap_quiet_get(lis2dw12_ctx_t *ctx, uint8_t *val)
+{
+ lis2dw12_reg_t reg;
+ int32_t mm_error;
+
+ mm_error = lis2dw12_read_reg(ctx, LIS2DW12_INT_DUR, ®.byte, 1);
+ *val = reg.int_dur.quiet;
+
+ return mm_error;
+}
+
+/**
+ * @brief tap_dur: [set] When double tap recognition is enabled,
+ * this register expresses the maximum time
+ * between two consecutive detected taps to
+ * determine a double tap event.
+ * The default value of these bits is 0000b
+ * which corresponds to 16*ODR_XL time.
+ * If the DUR[3:0] bits are set to a different value,
+ * 1LSB corresponds to 32*ODR_XL time.
+ *
+ * @param lis2dw12_ctx_t *ctx: read / write interface definitions
+ * @param uint8_t val: change the values of latency in reg INT_DUR
+ *
+ */
+int32_t lis2dw12_tap_dur_set(lis2dw12_ctx_t *ctx, uint8_t val)
+{
+ lis2dw12_reg_t reg;
+ int32_t mm_error;
+
+ mm_error = lis2dw12_read_reg(ctx, LIS2DW12_INT_DUR, ®.byte, 1);
+ reg.int_dur.latency = val;
+ mm_error = lis2dw12_write_reg(ctx, LIS2DW12_INT_DUR, ®.byte, 1);
+
+ return mm_error;
+}
+
+/**
+ * @brief tap_dur: [get] When double tap recognition is enabled,
+ * this register expresses the maximum time
+ * between two consecutive detected taps to
+ * determine a double tap event.
+ * The default value of these bits is 0000b
+ * which corresponds to 16*ODR_XL time.
+ * If the DUR[3:0] bits are set to a different
+ * value, 1LSB corresponds to 32*ODR_XL time.
+ *
+ * @param lis2dw12_ctx_t *ctx: read / write interface definitions
+ * @param uint8_t: change the values of latency in reg INT_DUR
+ *
+ */
+int32_t lis2dw12_tap_dur_get(lis2dw12_ctx_t *ctx, uint8_t *val)
+{
+ lis2dw12_reg_t reg;
+ int32_t mm_error;
+
+ mm_error = lis2dw12_read_reg(ctx, LIS2DW12_INT_DUR, ®.byte, 1);
+ *val = reg.int_dur.latency;
+
+ return mm_error;
+}
+
+/**
+ * @brief tap_mode: [set] Single/double-tap event enable.
+ *
+ * @param lis2dw12_ctx_t *ctx: read / write interface definitions
+ * @param lis2dw12_single_double_tap_t: change the values of
+ * single_double_tap in reg WAKE_UP_THS
+ *
+ */
+int32_t lis2dw12_tap_mode_set(lis2dw12_ctx_t *ctx,
+ lis2dw12_single_double_tap_t val)
+{
+ lis2dw12_reg_t reg;
+ int32_t mm_error;
+
+ mm_error = lis2dw12_read_reg(ctx, LIS2DW12_WAKE_UP_THS, ®.byte, 1);
+ reg.wake_up_ths.single_double_tap = val;
+ mm_error = lis2dw12_write_reg(ctx, LIS2DW12_WAKE_UP_THS, ®.byte, 1);
+
+ return mm_error;
+}
+
+/**
+ * @brief tap_mode: [get] Single/double-tap event enable.
+ *
+ * @param lis2dw12_ctx_t *ctx: read / write interface definitions
+ * @param lis2dw12_single_double_tap_t: Get the values of single_double_tap
+ * in reg WAKE_UP_THS
+ *
+ */
+int32_t lis2dw12_tap_mode_get(lis2dw12_ctx_t *ctx,
+ lis2dw12_single_double_tap_t *val)
+{
+ lis2dw12_reg_t reg;
+ int32_t mm_error;
+
+ mm_error = lis2dw12_read_reg(ctx, LIS2DW12_WAKE_UP_THS, ®.byte, 1);
+ *val = (lis2dw12_single_double_tap_t) reg.wake_up_ths.single_double_tap;
+
+ return mm_error;
+}
+
+/**
+ * @brief tap_src: [get] Read the tap / double tap source register.
+ *
+ * @param lis2dw12_ctx_t *ctx: read / write interface definitions
+ * @param lis2dw12_tap_src: union of registers from TAP_SRC to
+ *
+ */
+int32_t lis2dw12_tap_src_get(lis2dw12_ctx_t *ctx, lis2dw12_tap_src_t *val)
+{
+ return lis2dw12_read_reg(ctx, LIS2DW12_TAP_SRC, (uint8_t*) val, 1);
+}
+/**
+ * @}
+ */
+
+/**
+ * @addtogroup Six_position_detection(6D/4D)
+ * @brief This section groups all the functions concerning six
+ * position detection (6D).
+ * @{
+ */
+
+/**
+ * @brief 6d_threshold: [set] Threshold for 4D/6D function.
+ *
+ * @param lis2dw12_ctx_t *ctx: read / write interface definitions
+ * @param uint8_t val: change the values of 6d_ths in reg TAP_THS_X
+ *
+ */
+int32_t lis2dw12_6d_threshold_set(lis2dw12_ctx_t *ctx, uint8_t val)
+{
+ lis2dw12_reg_t reg;
+ int32_t mm_error;
+
+ mm_error = lis2dw12_read_reg(ctx, LIS2DW12_TAP_THS_X, ®.byte, 1);
+ reg.tap_ths_x._6d_ths = val;
+ mm_error = lis2dw12_write_reg(ctx, LIS2DW12_TAP_THS_X, ®.byte, 1);
+
+ return mm_error;
+}
+
+/**
+ * @brief 6d_threshold: [get] Threshold for 4D/6D function.
+ *
+ * @param lis2dw12_ctx_t *ctx: read / write interface definitions
+ * @param uint8_t: change the values of 6d_ths in reg TAP_THS_X
+ *
+ */
+int32_t lis2dw12_6d_threshold_get(lis2dw12_ctx_t *ctx, uint8_t *val)
+{
+ lis2dw12_reg_t reg;
+ int32_t mm_error;
+
+ mm_error = lis2dw12_read_reg(ctx, LIS2DW12_TAP_THS_X, ®.byte, 1);
+ *val = reg.tap_ths_x._6d_ths;
+
+ return mm_error;
+}
+
+/**
+ * @brief 4d_mode: [set] 4D orientation detection enable.
+ *
+ * @param lis2dw12_ctx_t *ctx: read / write interface definitions
+ * @param uint8_t val: change the values of 4d_en in reg TAP_THS_X
+ *
+ */
+int32_t lis2dw12_4d_mode_set(lis2dw12_ctx_t *ctx, uint8_t val)
+{
+ lis2dw12_reg_t reg;
+ int32_t mm_error;
+
+ mm_error = lis2dw12_read_reg(ctx, LIS2DW12_TAP_THS_X, ®.byte, 1);
+ reg.tap_ths_x._4d_en = val;
+ mm_error = lis2dw12_write_reg(ctx, LIS2DW12_TAP_THS_X, ®.byte, 1);
+
+ return mm_error;
+}
+
+/**
+ * @brief 4d_mode: [get] 4D orientation detection enable.
+ *
+ * @param lis2dw12_ctx_t *ctx: read / write interface definitions
+ * @param uint8_t: change the values of 4d_en in reg TAP_THS_X
+ *
+ */
+int32_t lis2dw12_4d_mode_get(lis2dw12_ctx_t *ctx, uint8_t *val)
+{
+ lis2dw12_reg_t reg;
+ int32_t mm_error;
+
+ mm_error = lis2dw12_read_reg(ctx, LIS2DW12_TAP_THS_X, ®.byte, 1);
+ *val = reg.tap_ths_x._4d_en;
+
+ return mm_error;
+}
+
+/**
+ * @brief 6d_src: [get] Read the 6D tap source register.
+ *
+ * @param lis2dw12_ctx_t *ctx: read / write interface definitions
+ * @param lis2dw12_6d_src: union of registers from SIXD_SRC to
+ *
+ */
+int32_t lis2dw12_6d_src_get(lis2dw12_ctx_t *ctx, lis2dw12_sixd_src_t *val)
+{
+ return lis2dw12_read_reg(ctx, LIS2DW12_SIXD_SRC, (uint8_t*) val, 1);
+}
+/**
+ * @brief 6d_feed_data: [set] Data sent to 6D interrupt function.
+ *
+ * @param lis2dw12_ctx_t *ctx: read / write interface definitions
+ * @param lis2dw12_lpass_on6d_t: change the values of lpass_on6d in
+ * reg CTRL_REG7
+ *
+ */
+int32_t lis2dw12_6d_feed_data_set(lis2dw12_ctx_t *ctx,
+ lis2dw12_lpass_on6d_t val)
+{
+ lis2dw12_reg_t reg;
+ int32_t mm_error;
+
+ mm_error = lis2dw12_read_reg(ctx, LIS2DW12_CTRL_REG7, ®.byte, 1);
+ reg.ctrl_reg7.lpass_on6d = val;
+ mm_error = lis2dw12_write_reg(ctx, LIS2DW12_CTRL_REG7, ®.byte, 1);
+
+ return mm_error;
+}
+
+/**
+ * @brief 6d_feed_data: [get] Data sent to 6D interrupt function.
+ *
+ * @param lis2dw12_ctx_t *ctx: read / write interface definitions
+ * @param lis2dw12_lpass_on6d_t: Get the values of lpass_on6d in
+ * reg CTRL_REG7
+ *
+ */
+int32_t lis2dw12_6d_feed_data_get(lis2dw12_ctx_t *ctx,
+ lis2dw12_lpass_on6d_t *val)
+{
+ lis2dw12_reg_t reg;
+ int32_t mm_error;
+
+ mm_error = lis2dw12_read_reg(ctx, LIS2DW12_CTRL_REG7, ®.byte, 1);
+ *val = (lis2dw12_lpass_on6d_t) reg.ctrl_reg7.lpass_on6d;
+
+ return mm_error;
+}
+
+/**
+ * @}
+ */
+
+/**
+ * @addtogroup free_fall
+ * @brief This section group all the functions concerning
+ * the free fall detection.
+ * @{
+ */
+
+/**
+ * @brief ff_dur: [set] Wake up duration event.1LSb = 1 / ODR.
+ *
+ * @param lis2dw12_ctx_t *ctx: read / write interface definitions
+ * @param uint8_t val: change the values of ff_dur in
+ * reg WAKE_UP_DUR /F REE_FALL
+ *
+ */
+int32_t lis2dw12_ff_dur_set(lis2dw12_ctx_t *ctx, uint8_t val)
+{
+ lis2dw12_reg_t reg[2];
+ int32_t mm_error;
+
+ mm_error = lis2dw12_read_reg(ctx, LIS2DW12_WAKE_UP_DUR, ®[0].byte, 2);
+ reg[0].wake_up_dur.ff_dur = (val & 0x20) >> 5;
+ reg[1].free_fall.ff_dur = val & 0x1F;
+ mm_error = lis2dw12_write_reg(ctx, LIS2DW12_WAKE_UP_DUR, ®[0].byte, 2);
+
+ return mm_error;
+}
+
+/**
+ * @brief ff_dur: [get] Wake up duration event.1LSb = 1 / ODR.
+ *
+ * @param lis2dw12_ctx_t *ctx: read / write interface definitions
+ * @param uint8_t: change the values of ff_dur in
+ * reg WAKE_UP_DUR /F REE_FALL
+ *
+ */
+int32_t lis2dw12_ff_dur_get(lis2dw12_ctx_t *ctx, uint8_t *val)
+{
+ lis2dw12_reg_t reg[2];
+ int32_t mm_error;
+
+ mm_error = lis2dw12_read_reg(ctx, LIS2DW12_WAKE_UP_DUR, ®[0].byte, 2);
+ *val = (reg[0].wake_up_dur.ff_dur << 5) + reg[1].free_fall.ff_dur;
+
+ return mm_error;
+}
+
+/**
+ * @brief ff_threshold: [set] Free fall threshold setting.
+ *
+ * @param lis2dw12_ctx_t *ctx: read / write interface definitions
+ * @param lis2dw12_ff_ths_t: change the values of ff_ths in reg FREE_FALL
+ *
+ */
+int32_t lis2dw12_ff_threshold_set(lis2dw12_ctx_t *ctx, lis2dw12_ff_ths_t val)
+{
+ lis2dw12_reg_t reg;
+ int32_t mm_error;
+
+ mm_error = lis2dw12_read_reg(ctx, LIS2DW12_FREE_FALL, ®.byte, 1);
+ reg.free_fall.ff_ths = val;
+ mm_error = lis2dw12_write_reg(ctx, LIS2DW12_FREE_FALL, ®.byte, 1);
+
+ return mm_error;
+}
+
+/**
+ * @brief ff_threshold: [get] Free fall threshold setting.
+ *
+ * @param lis2dw12_ctx_t *ctx: read / write interface definitions
+ * @param lis2dw12_ff_ths_t: Get the values of ff_ths in reg FREE_FALL
+ *
+ */
+int32_t lis2dw12_ff_threshold_get(lis2dw12_ctx_t *ctx,
+ lis2dw12_ff_ths_t *val)
+{
+ lis2dw12_reg_t reg;
+ int32_t mm_error;
+
+ mm_error = lis2dw12_read_reg(ctx, LIS2DW12_FREE_FALL, ®.byte, 1);
+ *val = (lis2dw12_ff_ths_t) reg.free_fall.ff_ths;
+
+ return mm_error;
+}
+
+/**
+ * @}
+ */
+
+/**
+ * @addtogroup fifo
+ * @brief This section group all the functions concerning the fifo usage
+ * @{
+ */
+
+/**
+ * @brief fifo_watermark: [set] FIFO watermark level selection.
+ *
+ * @param lis2dw12_ctx_t *ctx: read / write interface definitions
+ * @param uint8_t val: change the values of fth in reg FIFO_CTRL
+ *
+ */
+int32_t lis2dw12_fifo_watermark_set(lis2dw12_ctx_t *ctx, uint8_t val)
+{
+ lis2dw12_reg_t reg;
+ int32_t mm_error;
+
+ mm_error = lis2dw12_read_reg(ctx, LIS2DW12_FIFO_CTRL, ®.byte, 1);
+ reg.fifo_ctrl.fth = val;
+ mm_error = lis2dw12_write_reg(ctx, LIS2DW12_FIFO_CTRL, ®.byte, 1);
+
+ return mm_error;
+}
+
+/**
+ * @brief fifo_watermark: [get] FIFO watermark level selection.
+ *
+ * @param lis2dw12_ctx_t *ctx: read / write interface definitions
+ * @param uint8_t: change the values of fth in reg FIFO_CTRL
+ *
+ */
+int32_t lis2dw12_fifo_watermark_get(lis2dw12_ctx_t *ctx, uint8_t *val)
+{
+ lis2dw12_reg_t reg;
+ int32_t mm_error;
+
+ mm_error = lis2dw12_read_reg(ctx, LIS2DW12_FIFO_CTRL, ®.byte, 1);
+ *val = reg.fifo_ctrl.fth;
+
+ return mm_error;
+}
+
+/**
+ * @brief fifo_mode: [set] FIFO mode selection.
+ *
+ * @param lis2dw12_ctx_t *ctx: read / write interface definitions
+ * @param lis2dw12_fmode_t: change the values of fmode in reg FIFO_CTRL
+ *
+ */
+int32_t lis2dw12_fifo_mode_set(lis2dw12_ctx_t *ctx, lis2dw12_fmode_t val)
+{
+ lis2dw12_reg_t reg;
+ int32_t mm_error;
+
+ mm_error = lis2dw12_read_reg(ctx, LIS2DW12_FIFO_CTRL, ®.byte, 1);
+ reg.fifo_ctrl.fmode = val;
+ mm_error = lis2dw12_write_reg(ctx, LIS2DW12_FIFO_CTRL, ®.byte, 1);
+
+ return mm_error;
+}
+
+/**
+ * @brief fifo_mode: [get] FIFO mode selection.
+ *
+ * @param lis2dw12_ctx_t *ctx: read / write interface definitions
+ * @param lis2dw12_fmode_t: Get the values of fmode in reg FIFO_CTRL
+ *
+ */
+int32_t lis2dw12_fifo_mode_get(lis2dw12_ctx_t *ctx, lis2dw12_fmode_t *val)
+{
+ lis2dw12_reg_t reg;
+ int32_t mm_error;
+
+ mm_error = lis2dw12_read_reg(ctx, LIS2DW12_FIFO_CTRL, ®.byte, 1);
+ *val = (lis2dw12_fmode_t) reg.fifo_ctrl.fmode;
+
+ return mm_error;
+}
+
+/**
+ * @brief fifo_data_level: [get] Number of unread samples stored in FIFO.
+ *
+ * @param lis2dw12_ctx_t *ctx: read / write interface definitions
+ * @param uint8_t: change the values of diff in reg FIFO_SAMPLES
+ *
+ */
+int32_t lis2dw12_fifo_data_level_get(lis2dw12_ctx_t *ctx, uint8_t *val)
+{
+ lis2dw12_reg_t reg;
+ int32_t mm_error;
+
+ mm_error = lis2dw12_read_reg(ctx, LIS2DW12_FIFO_SAMPLES, ®.byte, 1);
+ *val = reg.fifo_samples.diff;
+
+ return mm_error;
+}
+/**
+ * @brief fifo_ovr_flag: [get] FIFO overrun status.
+ *
+ * @param lis2dw12_ctx_t *ctx: read / write interface definitions
+ * @param uint8_t: change the values of fifo_ovr in reg FIFO_SAMPLES
+ *
+ */
+int32_t lis2dw12_fifo_ovr_flag_get(lis2dw12_ctx_t *ctx, uint8_t *val)
+{
+ lis2dw12_reg_t reg;
+ int32_t mm_error;
+
+ mm_error = lis2dw12_read_reg(ctx, LIS2DW12_FIFO_SAMPLES, ®.byte, 1);
+ *val = reg.fifo_samples.fifo_ovr;
+
+ return mm_error;
+}
+/**
+ * @brief fifo_wtm_flag: [get] FIFO threshold status flag.
+ *
+ * @param lis2dw12_ctx_t *ctx: read / write interface definitions
+ * @param uint8_t: change the values of fifo_fth in reg FIFO_SAMPLES
+ *
+ */
+int32_t lis2dw12_fifo_wtm_flag_get(lis2dw12_ctx_t *ctx, uint8_t *val)
+{
+ lis2dw12_reg_t reg;
+ int32_t mm_error;
+
+ mm_error = lis2dw12_read_reg(ctx, LIS2DW12_FIFO_SAMPLES, ®.byte, 1);
+ *val = reg.fifo_samples.fifo_fth;
+
+ return mm_error;
+}
+/**
+ * @}
+ */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/