File content as of revision 0:2ddc0583bcec:

/*
 * Copyright (c) 2012, STMicroelectronics.
 * All rights reserved.
 *
 * Redistribution and use in source and binary forms, with or without
 * modification, are permitted provided that the following conditions
 * are met:
 * 1. Redistributions of source code must retain the above copyright
 *    notice, this list of conditions and the following disclaimer.
 * 2. Redistributions in binary form must reproduce the above copyright
 *    notice, this list of conditions and the following disclaimer in the
 *    documentation and/or other materials provided with the distribution.
 * 3. Neither the name of the Institute nor the names of its contributors
 *    may be used to endorse or promote products derived from this software
 *    without specific prior written permission.
 *
 * THIS SOFTWARE IS PROVIDED BY THE INSTITUTE AND CONTRIBUTORS ``AS IS'' AND
 * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
 * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
 * ARE DISCLAIMED.  IN NO EVENT SHALL THE INSTITUTE OR CONTRIBUTORS BE LIABLE
 * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
 * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
 * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
 * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
 * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
 * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
 * SUCH DAMAGE.
 *
 * This file is part of the Contiki operating system.
 *
 */
/*---------------------------------------------------------------------------*/
#ifndef __SPIRIT1_CONFIG_H__
#define __SPIRIT1_CONFIG_H__
/*---------------------------------------------------------------------------*/
#include "radio.h"
#include "SPIRIT_Config.h"
#include "spirit1-const.h"
/*---------------------------------------------------------------------------*/
#define CCA_THRESHOLD               -98.0   /* dBm */
#define XTAL_FREQUENCY              50000000    /* Hz */ 
#define SPIRIT_MAX_FIFO_LEN         (96) // betzw - WAS: 600
/*---------------------------------------------------------------------------*/

/* Sometimes Spirit1 seems to NOT deliver (correctly) the 'IRQ_RX_DATA_READY'
 * event for packets which have a length which is close to a multiple of
 * RX FIFO size. Furthermore, in these cases also the content delivery seems
 * to be compromised as well as the generation of RX/TX FIFO errors.
 * This can be avoided by reducing the maximum packet length to a value which
 * is lower than the RX FIFO size.
 *
 * Enable beyond macro if you want to use the version of the driver which avoids
 * FIFO overflows by reducing packet length.
 *
 * NOTE: the non delivery of event 'IRQ_RX_DATA_READY' MUST still be
 *       investigated further deeply (both on HW & SW level)!
 */
#define RX_FIFO_THR_WA

/**    
 * The MAX_PACKET_LEN is an arbitrary value used to define the two array
 * spirit_txbuf and spirit_rxbuf.
 * The SPIRIT1 supports with its packet handler a length of 65,535 bytes,
 * and in direct mode (without packet handler) there is no limit of data.
 */
#ifdef RX_FIFO_THR_WA
#define MAX_PACKET_LEN              (SPIRIT_MAX_FIFO_LEN-1)
#else
#define MAX_PACKET_LEN              (255) // betzw - WAS: SPIRIT_MAX_FIFO_LEN, but LEN_WIDTH is set to 7 so the variable payload length is theoretically from 0 to 255 bytes
#endif

/*---------------------------------------------------------------------------*/
/**    
 * Spirit1 IC version
 */
#define SPIRIT1_VERSION             SPIRIT_VERSION_3_0
/*---------------------------------------------------------------------------*/
#endif /* __SPIRIT1_CONFIG_H__ */
/*---------------------------------------------------------------------------*/