STM32746G-Discovery board drivers V1.0.0
Dependents: DISCO-F746NG_LCDTS_CC3000_NTP DISCO-F746NG_ROPE_WIFI F746_SpectralAnalysis_NoPhoto ecte433 ... more
Diff: Drivers/BSP/STM32746G-Discovery/stm32746g_discovery.h
- Revision:
- 6:e1d9da7fe856
- Child:
- 8:56384bddaba5
diff -r 5a395e126678 -r e1d9da7fe856 Drivers/BSP/STM32746G-Discovery/stm32746g_discovery.h --- /dev/null Thu Jan 01 00:00:00 1970 +0000 +++ b/Drivers/BSP/STM32746G-Discovery/stm32746g_discovery.h Thu Nov 10 09:57:11 2016 +0100 @@ -0,0 +1,342 @@ +/** + ****************************************************************************** + * @file stm32746g_discovery.h + * @author MCD Application Team + * @version V1.1.1 + * @date 02-June-2016 + * @brief This file contains definitions for STM32746G_DISCOVERY's LEDs, + * push-buttons and COM ports hardware resources. + ****************************************************************************** + * @attention + * + * <h2><center>© COPYRIGHT(c) 2016 STMicroelectronics</center></h2> + * + * Redistribution and use in source and binary forms, with or without modification, + * are permitted provided that the following conditions are met: + * 1. Redistributions of source code must retain the above copyright notice, + * this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright notice, + * this list of conditions and the following disclaimer in the documentation + * and/or other materials provided with the distribution. + * 3. Neither the name of STMicroelectronics nor the names of its contributors + * may be used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" + * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE + * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE + * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL + * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR + * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER + * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, + * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE + * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + * + ****************************************************************************** + */ + +/* Define to prevent recursive inclusion -------------------------------------*/ +#ifndef __STM32746G_DISCOVERY_H +#define __STM32746G_DISCOVERY_H + +#ifdef __cplusplus + extern "C" { +#endif + +/* Includes ------------------------------------------------------------------*/ +#include "stm32f7xx_hal.h" +#include "cmsis_nvic.h" // MBED + +/** @addtogroup BSP + * @{ + */ + +/** @addtogroup STM32746G_DISCOVERY + * @{ + */ + +/** @addtogroup STM32746G_DISCOVERY_LOW_LEVEL + * @{ + */ + +/** @defgroup STM32746G_DISCOVERY_LOW_LEVEL_Exported_Types STM32746G_DISCOVERY_LOW_LEVEL Exported Types + * @{ + */ +typedef enum +{ + DISCO_LED1 = 0, // MBED + LED_GREEN = DISCO_LED1, // MBED +}Led_TypeDef; + +typedef enum +{ + BUTTON_WAKEUP = 0, + BUTTON_TAMPER = 1, + BUTTON_KEY = 2 +}Button_TypeDef; + +typedef enum +{ + BUTTON_MODE_GPIO = 0, + BUTTON_MODE_EXTI = 1 +}ButtonMode_TypeDef; + +typedef enum +{ + COM1 = 0, + COM2 = 1 +}COM_TypeDef; +/** + * @} + */ + +/** @defgroup STM32746G_DISCOVERY_LOW_LEVEL_Exported_Constants STM32746G_DISCOVERY_LOW_LEVEL Exported Constants + * @{ + */ + +/** + * @brief Define for STM32746G_DISCOVERY board + */ +#if !defined (USE_STM32746G_DISCO) + #define USE_STM32746G_DISCO +#endif + +/** @addtogroup STM32746G_DISCOVERY_LOW_LEVEL_LED + * @{ + */ + +#define LEDn ((uint8_t)1) + +#define LED1_GPIO_PORT GPIOI +#define LED1_GPIO_CLK_ENABLE() __HAL_RCC_GPIOI_CLK_ENABLE() +#define LED1_GPIO_CLK_DISABLE() __HAL_RCC_GPIOI_CLK_DISABLE() +#define LED1_PIN GPIO_PIN_1 + +/** + * @} + */ + +/** @addtogroup STM32746G_DISCOVERY_LOW_LEVEL_BUTTON + * @{ + */ +#define BUTTONn ((uint8_t)3) + +/** + * @brief Wakeup push-button + */ +#define WAKEUP_BUTTON_PIN GPIO_PIN_11 +#define WAKEUP_BUTTON_GPIO_PORT GPIOI +#define WAKEUP_BUTTON_GPIO_CLK_ENABLE() __HAL_RCC_GPIOI_CLK_ENABLE() +#define WAKEUP_BUTTON_GPIO_CLK_DISABLE() __HAL_RCC_GPIOI_CLK_DISABLE() +#define WAKEUP_BUTTON_EXTI_IRQn EXTI15_10_IRQn + +/** + * @brief Tamper push-button + */ +#define TAMPER_BUTTON_PIN GPIO_PIN_11 +#define TAMPER_BUTTON_GPIO_PORT GPIOI +#define TAMPER_BUTTON_GPIO_CLK_ENABLE() __HAL_RCC_GPIOI_CLK_ENABLE() +#define TAMPER_BUTTON_GPIO_CLK_DISABLE() __HAL_RCC_GPIOI_CLK_DISABLE() +#define TAMPER_BUTTON_EXTI_IRQn EXTI15_10_IRQn + +/** + * @brief Key push-button + */ +#define KEY_BUTTON_PIN GPIO_PIN_11 +#define KEY_BUTTON_GPIO_PORT GPIOI +#define KEY_BUTTON_GPIO_CLK_ENABLE() __HAL_RCC_GPIOI_CLK_ENABLE() +#define KEY_BUTTON_GPIO_CLK_DISABLE() __HAL_RCC_GPIOI_CLK_DISABLE() +#define KEY_BUTTON_EXTI_IRQn EXTI15_10_IRQn + +#define BUTTONx_GPIO_CLK_ENABLE(__INDEX__) do { if((__INDEX__) == 0) WAKEUP_BUTTON_GPIO_CLK_ENABLE(); else\ + if((__INDEX__) == 1) TAMPER_BUTTON_GPIO_CLK_ENABLE(); else\ + KEY_BUTTON_GPIO_CLK_ENABLE(); } while(0) + +#define BUTTONx_GPIO_CLK_DISABLE(__INDEX__) (((__INDEX__) == 0) ? WAKEUP_BUTTON_GPIO_CLK_DISABLE() :\ + ((__INDEX__) == 1) ? TAMPER_BUTTON_GPIO_CLK_DISABLE() : KEY_BUTTON_GPIO_CLK_DISABLE()) + +/** + * @} + */ + +/** @addtogroup STM32746G_DISCOVERY_LOW_LEVEL_SIGNAL + * @{ + */ +#define SIGNALn ((uint8_t)1) + +/** + * @brief SD-detect signal + */ +#define SD_DETECT_PIN GPIO_PIN_13 +#define SD_DETECT_GPIO_PORT GPIOC +#define SD_DETECT_GPIO_CLK_ENABLE() __HAL_RCC_GPIOC_CLK_ENABLE() +#define SD_DETECT_GPIO_CLK_DISABLE() __HAL_RCC_GPIOC_CLK_DISABLE() +#define SD_DETECT_EXTI_IRQn EXTI15_10_IRQn + +/** + * @brief Touch screen interrupt signal + */ +#define TS_INT_PIN GPIO_PIN_13 +#define TS_INT_GPIO_PORT GPIOI +#define TS_INT_GPIO_CLK_ENABLE() __HAL_RCC_GPIOI_CLK_ENABLE() +#define TS_INT_GPIO_CLK_DISABLE() __HAL_RCC_GPIOI_CLK_DISABLE() +#define TS_INT_EXTI_IRQn EXTI15_10_IRQn + +/** + * @} + */ + +/** @addtogroup STM32746G_DISCOVERY_LOW_LEVEL_COM + * @{ + */ +#define COMn ((uint8_t)1) + +/** + * @brief Definition for COM port1, connected to USART1 + */ +#define DISCOVERY_COM1 USART1 +#define DISCOVERY_COM1_CLK_ENABLE() __HAL_RCC_USART1_CLK_ENABLE() +#define DISCOVERY_COM1_CLK_DISABLE() __HAL_RCC_USART1_CLK_DISABLE() + +#define DISCOVERY_COM1_TX_PIN GPIO_PIN_9 +#define DISCOVERY_COM1_TX_GPIO_PORT GPIOA +#define DISCOVERY_COM1_TX_GPIO_CLK_ENABLE() __HAL_RCC_GPIOA_CLK_ENABLE() +#define DISCOVERY_COM1_TX_GPIO_CLK_DISABLE() __HAL_RCC_GPIOA_CLK_DISABLE() +#define DISCOVERY_COM1_TX_AF GPIO_AF7_USART1 + +#define DISCOVERY_COM1_RX_PIN GPIO_PIN_7 +#define DISCOVERY_COM1_RX_GPIO_PORT GPIOB +#define DISCOVERY_COM1_RX_GPIO_CLK_ENABLE() __HAL_RCC_GPIOB_CLK_ENABLE() +#define DISCOVERY_COM1_RX_GPIO_CLK_DISABLE() __HAL_RCC_GPIOB_CLK_DISABLE() +#define DISCOVERY_COM1_RX_AF GPIO_AF7_USART1 + +#define DISCOVERY_COM1_IRQn USART1_IRQn + +#define DISCOVERY_COMx_CLK_ENABLE(__INDEX__) do { if((__INDEX__) == COM1) DISCOVERY_COM1_CLK_ENABLE(); } while(0) +#define DISCOVERY_COMx_CLK_DISABLE(__INDEX__) (((__INDEX__) == 0) ? DISCOVERY_COM1_CLK_DISABLE() : 0) + +#define DISCOVERY_COMx_TX_GPIO_CLK_ENABLE(__INDEX__) do { if((__INDEX__) == COM1) DISCOVERY_COM1_TX_GPIO_CLK_ENABLE(); } while(0) +#define DISCOVERY_COMx_TX_GPIO_CLK_DISABLE(__INDEX__) (((__INDEX__) == 0) ? DISCOVERY_COM1_TX_GPIO_CLK_DISABLE() : 0) + +#define DISCOVERY_COMx_RX_GPIO_CLK_ENABLE(__INDEX__) do { if((__INDEX__) == COM1) DISCOVERY_COM1_RX_GPIO_CLK_ENABLE(); } while(0) +#define DISCOVERY_COMx_RX_GPIO_CLK_DISABLE(__INDEX__) (((__INDEX__) == 0) ? DISCOVERY_COM1_RX_GPIO_CLK_DISABLE() : 0) + +/* Exported constant IO ------------------------------------------------------*/ + +#define LCD_I2C_ADDRESS ((uint16_t)0x70) +#define CAMERA_I2C_ADDRESS ((uint16_t)0x60) +#define AUDIO_I2C_ADDRESS ((uint16_t)0x34) +#define EEPROM_I2C_ADDRESS_A01 ((uint16_t)0xA0) +#define EEPROM_I2C_ADDRESS_A02 ((uint16_t)0xA6) +#define TS_I2C_ADDRESS ((uint16_t)0x70) + +/* I2C clock speed configuration (in Hz) + WARNING: + Make sure that this define is not already declared in other files (ie. + stm32746g_discovery.h file). It can be used in parallel by other modules. */ +#ifndef I2C_SPEED + #define I2C_SPEED ((uint32_t)100000) +#endif /* I2C_SPEED */ + +/* User can use this section to tailor I2Cx/I2Cx instance used and associated + resources */ +/* Definition for AUDIO and LCD I2Cx resources */ +#define DISCOVERY_AUDIO_I2Cx I2C3 +#define DISCOVERY_AUDIO_I2Cx_CLK_ENABLE() __HAL_RCC_I2C3_CLK_ENABLE() +#define DISCOVERY_AUDIO_DMAx_CLK_ENABLE() __HAL_RCC_DMA1_CLK_ENABLE() +#define DISCOVERY_AUDIO_I2Cx_SCL_SDA_GPIO_CLK_ENABLE() __HAL_RCC_GPIOH_CLK_ENABLE() + +#define DISCOVERY_AUDIO_I2Cx_FORCE_RESET() __HAL_RCC_I2C3_FORCE_RESET() +#define DISCOVERY_AUDIO_I2Cx_RELEASE_RESET() __HAL_RCC_I2C3_RELEASE_RESET() + +/* Definition for I2Cx Pins */ +#define DISCOVERY_AUDIO_I2Cx_SCL_PIN GPIO_PIN_7 +#define DISCOVERY_AUDIO_I2Cx_SCL_SDA_GPIO_PORT GPIOH +#define DISCOVERY_AUDIO_I2Cx_SCL_SDA_AF GPIO_AF4_I2C3 +#define DISCOVERY_AUDIO_I2Cx_SDA_PIN GPIO_PIN_8 + +/* I2C interrupt requests */ +#define DISCOVERY_AUDIO_I2Cx_EV_IRQn I2C3_EV_IRQn +#define DISCOVERY_AUDIO_I2Cx_ER_IRQn I2C3_ER_IRQn + +/* Definition for external, camera and Arduino connector I2Cx resources */ +#define DISCOVERY_EXT_I2Cx I2C1 +#define DISCOVERY_EXT_I2Cx_CLK_ENABLE() __HAL_RCC_I2C1_CLK_ENABLE() +#define DISCOVERY_EXT_DMAx_CLK_ENABLE() __HAL_RCC_DMA1_CLK_ENABLE() +#define DISCOVERY_EXT_I2Cx_SCL_SDA_GPIO_CLK_ENABLE() __HAL_RCC_GPIOB_CLK_ENABLE() + +#define DISCOVERY_EXT_I2Cx_FORCE_RESET() __HAL_RCC_I2C1_FORCE_RESET() +#define DISCOVERY_EXT_I2Cx_RELEASE_RESET() __HAL_RCC_I2C1_RELEASE_RESET() + +/* Definition for I2Cx Pins */ +#define DISCOVERY_EXT_I2Cx_SCL_PIN GPIO_PIN_8 +#define DISCOVERY_EXT_I2Cx_SCL_SDA_GPIO_PORT GPIOB +#define DISCOVERY_EXT_I2Cx_SCL_SDA_AF GPIO_AF4_I2C1 +#define DISCOVERY_EXT_I2Cx_SDA_PIN GPIO_PIN_9 + +/* I2C interrupt requests */ +#define DISCOVERY_EXT_I2Cx_EV_IRQn I2C1_EV_IRQn +#define DISCOVERY_EXT_I2Cx_ER_IRQn I2C1_ER_IRQn + +/* I2C TIMING Register define when I2C clock source is SYSCLK */ +/* I2C TIMING is calculated from APB1 source clock = 50 MHz */ +/* Due to the big MOFSET capacity for adapting the camera level the rising time is very large (>1us) */ +/* 0x40912732 takes in account the big rising and aims a clock of 100khz */ +#ifndef DISCOVERY_I2Cx_TIMING +#define DISCOVERY_I2Cx_TIMING ((uint32_t)0x40912732) +#endif /* DISCOVERY_I2Cx_TIMING */ + +/** + * @} + */ + +/** + * @} + */ + +/** @defgroup STM32746G_DISCOVERY_LOW_LEVEL_Exported_Macros STM32746G_DISCOVERY_LOW_LEVEL Exported Macros + * @{ + */ +/** + * @} + */ + +/** @addtogroup STM32746G_DISCOVERY_LOW_LEVEL_Exported_Functions + * @{ + */ +uint32_t BSP_GetVersion(void); +void BSP_LED_Init(Led_TypeDef Led); +void BSP_LED_DeInit(Led_TypeDef Led); +void BSP_LED_On(Led_TypeDef Led); +void BSP_LED_Off(Led_TypeDef Led); +void BSP_LED_Toggle(Led_TypeDef Led); +void BSP_PB_Init(Button_TypeDef Button, ButtonMode_TypeDef ButtonMode); +void BSP_PB_DeInit(Button_TypeDef Button); +uint32_t BSP_PB_GetState(Button_TypeDef Button); +void BSP_COM_Init(COM_TypeDef COM, UART_HandleTypeDef *husart); +void BSP_COM_DeInit(COM_TypeDef COM, UART_HandleTypeDef *huart); + +/** + * @} + */ + +/** + * @} + */ + +/** + * @} + */ + +/** + * @} + */ + +#ifdef __cplusplus +} +#endif + +#endif /* __STM32746G_DISCOVERY_H */ + +/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/